Search Documents

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

TEST DECK - ALTIMETER SURVEY WITHOUT ALTMETER TEMPERATURE CORRECTION 1 BAS 8: 22 1391 1391 53. 49.

Jan 1, 1977

Provide a simple and effective means of measuring mining-induced pressure changes in coal mine roof and pillars. Approach Develop a reliable, easy to fabricate and install borehole instrument which measures mining-induced pressure changes in pillars and in the mine roof. Ground pressures are monitored through use of aluminum platens coupled with d copper flat jack. How It Works The Bureau's instrument measures mining-induced pressure changes by transmitting strata pressure through the aluminum platens to an oil-filled borehole platened flat jack (BPF). Pressure in the flat jack is displayed on a gage located outside of the borehole. The instrument is in-stalled in the borehole by inflating the flat jack using a hand-held hydraulic pump. In addition, the platens have been designed to allow up to three BPFs to be installed in a single borehole, thus permitting pressure change measurements in more than one direction from a single borehole. Installation pressure is calculated on the basis of the estimated pressure exerted by the overburden and the percent of recovery after intial mining has

Jan 1, 1986

Provide roof to floor closure rate measurements during underground mining, especially retreat mining of coal pillars, thereby helping the miners predict an imminent roof fall. Approach An electronic device and rugged potentiometric extensometer were developed to provide a means fur measuring total closure and the rate of closure. How It Works An intrinsically safe, battery operated instrument is enclosed in a rugged, hand carried field case. The unit is constructed using low-power, integrated circuits to provide minimal battery drain. Two digital Light Emitting Diode (LED) readouts are used; one displays the rate, the other displays the total closure. The unit will measure one extensometer continuously or two extensometers alternately. Two potentiometric extensometers with a closure measurement range of 6 inches are attached to the readout unit. As the roof to floor closure changes, the potentiometric resistance

Jan 1, 1982

By Harry Dobroski, Larry G. Stolarczyk

Theoretical and experimental research sponsored by the U.S. Bureau of Mines shows that medium frequency (MF) electromagnetic (EM) signals propagate great distances in an underground environment such as a tunnel or mine. This propagation is enhanced by different mechanisms associated with the geology, and with the existence of metallic conductors in the entryways. In stratified geologies, a transverse electromagnetic (TEM) mode of signal propagation is possible if a low conducting layer is bounded above and below by higher conducting layers. In general, the difference in conductivities must be at least several orders of magnitude. Such geological waveguide conditions often exist in underground mines. Propagation via the waveguide effect is known as the "seam mode" of propagation. Another mode of propagation, the "tunnel mode," exists in underground entries with electrical conductors such as power cables, metal pipes, and phone lines. A monofilar mode of propagation exists when signals are impressed upon conductors and return via the surrounding rock. A bifilar mode of propagation exists when all signals exist only on local conductors. In a given location there is a combination of monofilar and bifilar modes that make possible an interaction between the conductors and a transmitting device in a tunnel or entryway. Signals can be impressed on or received from local conductors via magnetic dipole antennas (loops) or line couplers.

Improve safety at mineral operations that use cyanide leach solutions to recover precious metals from finely ground ores, Approach Provide an alternative, non-acidic means of cleaning processing systems such as the State-of-Maine filter system, thereby reducing the exposure of workers to toxic hydrogen cyanide gas (HCN), The Problem Many gold and silver mining operations use cyanide solutions to dissolve gold and silver from ores. The precious metals frequently are recovered from pregnant leach solutions by the Merrill-Crowe recovery process, whereby gold and silver is precipitated with zinc dust. When that method is used, suspended particles in the leach solution must be filtered out before zinc precipitation can occur. This filtering is accomplished with small packaged plants, such as the State-of-Maine (SOM) filtering system. Unfortunately, the filters become clogged with calcium carbonate scale after about 2 to 10 days of operation and must be cleaned before further precious metals recovery operations can continue, Cleaning the system is a hazardous task because the acid is not compatible with the alkaline cyanide leach solutions, and toxic hydrogen cyanide (HCN) gas may be produced when the acid and solution are mixed. That gas, if breathed or contacted with the skin, can cause cyanosis which may induce nausea and even asphyxia and death. To reduce this danger, the Bureau of Mines has devised a safer method of cleaning clogged filters,

Jan 1, 1986

By Larry Patts, Michael J. Brnich

Approximately 45% of U.S. coal is produced from underground mining. The use of diesel engines to power under- ground mining equipment has steadily increased over the past four decades in an effort to improve mine safety and productivity. Several advantages realized with the use of diesel-powered mining equipment in underground coal mines are listed in Table I. The primary disadvantage of using diesel equipment in underground coal mines is that diesel exhaust emissions can contaminate mine ventilation air. The major constituents of diesel exhaust are gaseous emissions (which include carbon monoxide, carbon dioxide, oxides of nitrogen, sulfur oxides and unburned hydrocarbons) and diesel particulate matter (DPM). The Mine Safety and Health Administration (MSHA) has incorporated threshold limit values for all gaseous components of diesel exhaust into their regulations. These have been established by the American Conference of Governmental Industrial Hygienists.

By Nicholas Kyriazi, John P. Shubilla

The National Institute for Occupational Safety and Health, National Personal Protective Technology Laboratory, has undertaken a study to determine how well self-contained self-rescuers (SCSRs), deployed in accordance with Federal regulations (30 CFR 75.1714), hold up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSRs in the seventh phase of testing from May 1999 to August 2000. The SCSRs were tested on human subjects and on a breathing and metabolic simulator. The results indicate that most of the apparatus, if they pass their approved inspection criteria, perform satisfactorily. The deployed CSE SR-100s, however, exhibited significantly higher inhaled carbon dioxide (CO2) levels than new units, as they did in the previous two phases. Several Draeger OXY K-Pluses that rattled when shaken were found to have potassium superoxide (KO2) particles throughout the breathing circuit, including the mouthpiece. Draeger investigated the problem and developed a shake test to detect damaged units. The durations of new Ocenco M-20s were statistically significantly longer than those of deployed units, although only by 2 min.

Jan 3, 2002

By Gene Asai

Properties obtained for columbium carbide-carbon castings ranging in car-bon content from 12 to 17 weight-percent were compared with those of hot-pressed composites of similar composition. The properties were oxidation resistance in static air between 500° and 700° C, linear thermal expansion between 20° and 2,400° C, electrical resistivity between 20° and 1,500° C; microhardness between 20° and 1,500° C, and modulus of rupture between 1,300° and 1,800° C. CbC-C castings differed markedly from hot-pressed material with respect to microstructure, electrical resistivity, and modulus of rupture, but behaved quite similarly with respect to oxidation resistance, thermal expansion, and hot hardness. In oxidation resistance, thermal expansion, and hot hardness both materials were independent of carbon content. Both castings and hot-pressed composites oxidize rapidly in air above 600° C, have thermal expansion coefficients very similar to columbium metal, and the logarithm of the hardness decreases linearly with increasing temperature. The microstructures of hot-pressed composites contained varying amounts of graphite in a CbC matrix but did not contain significant amounts of a eutectic structure present in all castings, nor did they contain graphite needles which were present in the hypereutectic castings. The higher electrical resistivity of hypereutectic castings over hypereutectic hot pressings was attributed to the presence of highly oriented graphite needles in the castings. The modulus of rupture of castings was 1-1/2 to 2 times that of hot-pressed composites. Both materials displayed bend ductility above 1,800° C.

Jan 1, 1971

ESTABLISHMENT of an effective inspection system has been held essen¬tial to any international agreement that may be designed primarily to curb the testing of nuclear weapons. A number of reports and papers already have described basic inspection concepts and appraised various pro¬cedures, techniques, and methods as to their probable effectiveness in detecting and identifying violations under such agreement. This report results from a study of only one part of the contemplated inspection system, specifically the final phases embracing onsite investigations and mine examination techniques. The results and reports of earlier work were reviewed in detail, and subjects that were found to have been exhaus¬tively evaluated are recognized by reference and not redescribed here. In other instances, previously described techniques, methods, and clues were revaluated to define more clearly their practical value to the final objective of an onsite inspection. Previous documentation does not refer to a number of subjects, techniques, tools, clues, and methods considered by the study; this report treats these in detail, even though when applied singly or collectively their practical value may be questionable.

Jan 1, 1962

By N. S. Dalal, X. Shi

"The oxidation of NADPH by vanadate(V) in the presence of glutathione reductase showed typical enzymatic kinetics. The oxidation was inhibited by N-ethylmaleimide, a glutathione reductase inhibitor. Superoxide dismutase had no significant effect on the oxidation, indicating non-involvment of the superoxide radical. The vanadate(V) reduction was found to be a one-electron transfer process. These results suggest a new pathway for vanadate(V) metabolism and a new function of glutathione reductase. Compounds of vanadium(V), such as NaV03 , exert potent toxic effects on a wide variety of biological systems (1-3). Despite intense current activity, however, the biochemical mechanism of vanadate(V) toxicity is still not well understood (1- 14). It is believed that one of the important pathways involves the oxidation (by vanadate(V)) of NAD(P)H (15, 16), but, to our knowledge, there has been no report of the identification of any vanadate(V) reductase. With a view to finding if there exists any vanadate(V) reductase, we have investigated the oxidation of NADPH by vanadate(V) in the presence of glutathione reductase. Glutathione reductase (GSSG-R)2 was selected because our previous studies have shown (17) that GSSG-R can act as a reductase for chromate(VI), which is isoelectronic with vanadate(V). We find that GSSG-R does indeed function as a NADPH-dependent vanadate(V) reductase, thus pointing to a new pathway for the metabolism of vanadate(V), as well as to this property for GSSG-R. MATERIALS AND METHODSSodium metavanadate (NaV03 ), henceforth vanadate, was purchased from Aldrich and its solution was always freshly prepared. The GSSG·R used was from bovine intestinal mucosa and was purchased from Sigma. The oxidation of NADPH was followed photometrically as the decrease in absorbance at 340 nm. The spin trap, 5,5-dimethyl- pyrroline-N-oxide (DMPO), was purchased from Aldrich and used without further purification, since very weak or no spin adduct signal was obtained from the purchased sample when used alone.ESR spectra were obtained at X-band (9.7 GHz) using a Bruker ER200 ESR spectrometer. The magnetic field was calibrated with a self-tracking NMR gaussmeter (Bruker, Model ER035A) and the microwave frequency was measured with a digital frequency counter (Hewlett-Packard, Model 5340A). An ASPECT 2000 computer was used for data storage and analysis. The concentrations given in the figure legends are the final concentrations. All experiments were carried out in the phosphate buffer solution (pH 7.2) and at room temperature."

Jan 1, 1990

By M. J. Beus, M. K. Larson, J. K. Whyatt

U.S. Bureau of Mines researchers reviewed an in situ stress estimate developed from measurements of overcore strain taken at test sites on the 7300 and 7500 levels of the Star Mine near Mullan, ID. Although the field measurements of overcoring strain were found to be useful, significant deficiencies were found in the stress estimation procedure. A new stress estimate was developed incorporating statistical methods and an improved understanding of stress concentration factors for interpreting overcore strains recorded by doorstopper cells. Spatial variability of overcore strains and the implications for stress field variability were explored.

Jan 1, 1995

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

APPENDIX F GOVERNMENT OFFICES CONTACTED DURING SURVEY 1. MESA Inspection Offices North Central District Duluth, Minnesota South Central District Dallas, Texas Rolla Subdistrict Rolla, Missouri Rocky Mountain District Lakewood, Colorado Salt Lake City Subdistrict Salt Lake City, Utah Spokane Field Office Spokane, Washington Osburn Field Office Osburn, Idaho Phoenix Subdistrict Phoenix, Arizona 2. MESA Research and Management Denver Technical Center Denver, Colorado Pittsburgh Technical Center Pittsburgh, Pennsylvania Metal and Non-Metal Office Washington, D C 3. State Offices (State plan States) Arizona State Mine Inspector Phoenix, Arizona New Mexico State Mine Inspector Albuquerque, New Mexico

Jan 1, 1976

By Walter J. Frank

Thls report summarizes work done under Bureau of Mines contract H0357100, "Development of a Crimp Connector for Trailing Cable Splices." The purpose of this effort was to establish optimum connector design conditions to meet flex cycle, pullout and electrical resistance criteria on phase power conductors. Field testing of "optimum design" connectors is briefly discussed. One of the primary objectives of contract H0357100 was to enable one to design better performing phase conductor connectors. Illustrating the practical significance of this 1s a discussion on the development of a new splice kit for trailing cables. The connectors in this kit were designed in accordance with the design methods described in the contract final report. Kit components, test data, and a connector installation tool are also discussed. The successful effort on the phase connector has resulted in contract H0377042, entitled "Design and Testing of Joining Sleeves for Trailing Cable Ground and Pilot Wires." The purpose of this contract (currently in effect) is to improve ground-conductor and pilot-wire performance. Significant findings to date are discussed.

Jan 1, 1979

To improve the reliability of the Bureau developed bore-hole gage now widely used to determine the absolute state of stress in rock. Approach Use the knowledge gained by extensive field tests to design a more rugged and reliable Instrument using lighter and stronger materials. How It Works The original gage consisted of a stainless steel cylinder 1-3/8 Inches In diameter and 10-1/2 inches long. The new gage is made from titanium. This lighter material reduces the weight of the gage by 43 percent, which enhances the gage placement and depth of overcoring in vertical up? holes. For added strength, the titanium case and placement end are now threaded to the gage body instead of using screw fasteners. Three pairs of strain gaged transducers are positioned to measure the diametral deformation of a 1-1/2 diameter borehole at 60-degree intervals around the Inner surface of the borehole. Each transducer consists of a beryllium copper cantilever with a strain gage cemented on each side. These transducers are secured Into the gage body by a tapered shank for minimal creep. The transducers opposite each other are wired together to form a 4-arm external bridge circuit. A pair of transducers is referred to as a component. Any deformation of the borehole, which occurs during overcoring, is detected by pistons which translate the motion to the components. Each

Jan 1, 1982

Predict the spontaneous combustion potential of a coal, using an expert system computer program. Background Approximately 15% of underground coal mint fires in the United States are attributed to spontaneous combustion. These spontaneous combustion fires frequently occur in worked-out or abandoned areas of a coal mine, This makes the control and extinguishment of the fire difficult and often requires large sections of the mine or even the entire mine to be scaled for long periods of time. A prior knowledge of the self-heating potential of the coal can be useful in preventing spontaneous combustion fires through the use of aggressive monitoring and control measures at existing coal mining operations, and in the planning oh new mines. Many factors can affect the spontaneous combustion process in a mine, including the self-heating potential of the coal, ventilation, geologic factors, and mining conditions and practices. Various test methods have been used to evaluate the relative self-healing potential of coals, including crossing point temperature and adiabatic heating methods, and oxygen adsorption techniques. However, these tests arc usually time-consuming and difficult to conduct, limiting their use to laboratories.

Jan 1, 1992

By Willis Beckering

The Bureau of Mines designed a cell having four variable compartments in series to facilitate analysis of multicomponent mixtures. Use of the cell considerably decreases the time required for differential absorption analyses. A solution of a major component is placed in each compartment, and the light absorbed by each of these components is varied by increasing or decreasing the path length of the appropriate cell. Simple calculations then establish the amount of the component present. In analyzing unknown mixtures, compensation is made for compounds known to be present, and the differential spectrum representing components not accounted for is recorded and analyzed.

Jan 1, 1966

By Alan G. Mayton

A prototype end-cab shuttle car (SC) design has been developed to improve protection and address ergonomic concerns of the SC operator in low coal mines. The new design features an end cab transversely mounted to the SC and equipped with a closed-circuit video system. The end cab was retrofitted to a low-coal SC and evaluated in surface trials at the U.S. Bureau of Mines. During surface trials, test operators evaluated the end-cab SC relative to visibility; cab features-space, seating, controls, and operator position; tramming-inby, outby, and turning corners; and dumping. Trials were conducted using 12 test subjects; 6 were experienced SC operators. Results of the trials were promising. Of the experienced operators, the only operator with low-coal experience gave the new design the highest rating. Four experienced operators rated the end-cab design "better" to "much better" than a standard center-driven, side-cab SC for visibility when tramming, protection from roof and rib hazards, and no change in seat position with direction of travel. This report discusses research to modify a used 21SC JOY SC, retrofit the SC with the Bureau-developed end-cab, and evaluate the retrofitted end-cab SC in surface trials.

Jan 1, 1993

By Thomas E. Marshall, Timothy Batchler, Anthony T. Iannacchione

As the amount of new fractured surfaces or "damaged rock layers" within roof rock increases, the stability of the rock mass decreases. While direct measurements of this phenomenon are not easily made, there is good circumstantial evidence to support this hypothesis. For example, it is common to observe increased cracks or fractures in the immediate mine roof rock before a roof fall. Likewise, roof drill holes placed in areas that later fail often reveal increased numbers and/or separations of fractures within the rock column through time. And finally, the frequency of microseismic activity, representative of rock fracturing, increases before a roof fall. For this study, more than 700 microseismic emissions were collected from two underground limestone mine roof fall areas in southwestern Pennsylvania. Microseismic events were located and magnitudes determined using the moment magnitude technique. Moment magnitude is based on the event seismic moment, which is a measure of the seismic deformation. The amount of new fracture surface length was calculated based on the stored strain energy within the rock prior to fracture. In the two case studies presented, a significant amount of microseismic activity was observed as much as two days before the first signs of failure in the roof fall areas. Additionally, results from this analysis reveal much about the behavior of strata prone to failure and allows for the construction of hazard maps based on microseismic emissions. The potential use of this technique as a means of anticipating roof falls is analyzed and discussed.

By T. N. McVay

The various applications of beryllium and its compounds in atomic - energy technology and a growing recognition of possible increased utilization of the metal in the aircraft and space - missile fields have resulted in increased interest in domestic and world reserves of beryllium . Unfortunately, little dependable data on beryllium resources and reserves are available , as past consumption of the element has been small and only limited prospecting and exploration work has been done . The scarcity of resource information is attributed partly to the difficulty of recognizing beryllium minerals in the field . These minerals frequently do not have distinctive characteristics of specific gravity, color , or other physical properties , that enable ready identification by the average prospector . This is particularly true of fine - grained minerals . As a result , a simple field test for identifying beryllium- bearing rock is needed . Recognizing this , technologists of the Federal Bureau of Mines investigated several of the proposed qualitative chemical tests for beryllium . This report describes various modifications of one of these methods to make it more suitable for use in the field . In the modified method , duplicate samples are fluxed -- one with potassium bifluoride and one with potassium bisulfate -- followed by dissolution of salts in water , conversion of the solution to an alkaline condition, addition of morin , and examination of the solution for fluorescence under short -wave ultraviolet light . This method provides a fast , dependable field test for beryllium minerals containing as little as 0.2 percent beryl or its equivalent . The test involves no radiation hazards , and it can be performed by persons having no technical training ; therefore , it should be useful to prospectors in discovering beryllium mineralization .

Jul 1, 1960

By A. A. Giardini

This report represents the results of a literature study on boron nitride and related substances. The purpose of the study was to find Information that might be of value for production of a new, hard modification of boron nitride preferably in single crystal form. The report consists of a review of the major developments in boron nitride research, a discussion of the results, tabulations of physical and chemical properties;, conclusions drawn from the study, and a bibliography.

Jan 1, 1953