Search Documents

By Dennis A. Long

Slip and fall accidents are a major cause of lost-time injuries associated with large mobile equipment in surface mines. An evaluation of the safety hazards associated with getting on and off large surface mining vehicles showed that most of the accidents occur at the point where personnel attempt to mount or dismount the machine at ground level. The major hazardous design conditions were identified as excessively flexible supports for lower steps or rungs, inappropriate ground-level-to-first-step distances, poor step designs, access designs that use vehicle components as steps or walkways, and inadequate hand- rail and guardrail designs, Additional hazards are introduced by the lack of proper maintenance of ladder hardware and the work practices of operators in carrying articles while mounting and dismounting the vehicle. This Bureau of Mines report describes the design and in-mine testing of improved access system for large mobile mining equipment.

Jan 1, 1984

By Philip G. Burkhalter

Total yield and backscattered electron coefficients were measured in this Bureau of Mines study in an microanalyzer as a function of atomic number and of primary crier: ;y in the 15- to 35-kilovolt range. The electron coefficients were obtained indirectly from measurements of the specimen electron current and the primary beam current collected in a Faraday cage and were measured with a precision better than 0.5 percent. Secondary electron emission was suppressed with opposing potential applied to a screen grid surrounding the specimen. The values of the backscattered electron coefficients agreed with published values within 5 percent.

Jan 1, 1965

Treat contaminated coal mine drainage to meet EPA and State water quality requirements. Approach A model (fig. 1) is presented for selecting, designing, and sizing one or several passive mine drainage treatment systems that can be used in remediation of abandoned mine lands (AML). The three principal types of passive mine drainage technologies for the treatment of coal mine drainage are an aerobic system, a compost wetland, and an anoxic limestone drain. The multistep approach presented here provides a simplified method to characterize the type and magnitude of the water quality problem and then to select either a single treatment system or a combination of treatment systems to address the specific site situation. How It Works Step 1. Discharge Characterization. Characterization of the discharge consists of measuring the discharge flow rate and collecting water samples at the point of discharge for chemical analysis. Both the flow rate and chemistry of a discharge can vary seasonally and in response to storm events. It is important to account for this variability by determining flow rates and water chemistry under various conditions.

Jan 1, 1992

By G. W. Weems

The Bureau of Mines combined preconcentrating techniques and mass spectrometry to develop a parts-per-billion general analysis of impurities in helium. The impurities are preconcentrated using a Bureau trace-impurity analyzer; 35-mm Hg pressure of helium is left in the concentration trap to sweep the impurities into the mass spectrometry and provide a 10-mm Hg sample pressure.

Jan 1, 1966

By J. F. Barkley

As part of the work of serving as Chairman of Subcommittee 3, Health and Industrial Requirements, of the American Society of Mechanical Engineers' Committee on Air-Pollution Controls, the author assembled the following information on accepted maximum permissible concentrations of air pollutants from the standpoints of health, damage to vegetation, damage to property, and requirements of industrial processes. A search in technical literature was made followed by direct inquiry to all State governments as to their regulations. The subcommittee membership - G. D. Clayton, senior sanitary engineer, Public Health Service, United States Department of Health, Education, and Welfare, Detroit, Mich., Dr. L. Greenburg, commissioner; Department of Air Pollution Control, New York, N.Y., Dr. M. Katz, Defence Research Chemical Laboratories, Ottawa, Ontario, Canada, and Dr. H. H. Schrenk, research director, Industrial Hygiene Foundation of America, Inc., Mellon Institute, Pittsburgh, Pa. - reviewed the information and made very helpful comments and corrections.

Jan 1, 1954

By John D. Corrick

The environmental and nutritional characteristics necessary for maximum copper extraction from a low-grade ore by Ferrobacillus ferrooxidans have been explored as have many of the limiting parameters. Criteria considered were oxygen consumption, copper extracted, soluble copper concentration, temperature, pH, particle size, nutrients, and other inorganic salt concentrations. A set of environmental and nutritional conditions were developed for E. ferrooxidans Which supported cell reproduction and maximum microbial oxidation of a low-grade copper sulfide ore. Percolator tests conducted under these optimum conditions resulted in an 18 percent increase in the quantity of copper microbially extracted over that extracted under conditions considered to be standard. Manometric tests determined those extremes of environmental conditions and nutritional factors Which were detrimental to the extraction of copper by E. ferrooxidans.

Jan 1, 1965

By E. W. Pehrson

In making any canvass of secondary metals great care must be exercised to avoid duplication or exaggeration of net consumption. One of the major difficulties is to trace the metal accurately as it passes through the many cycles of manufacture. Greater or less duplication probably occurs in any canvass. The manufacturer of tin plate, for instance, purchases primary pig tin exclusively as a raw material. Most of it goes into the coating on the steel sheet, but a substantial part emerges in the form of byproducts such as scruffs and drosses. These are sold to other plants, where they are used in the manufacture of alloys and chemicals. Alloys and chemicals, however, are not necessarily articles for final consumption. The alloy may be sold in ingot form to a bearing manufacturer, who, in turn may produce some scrap, which he may sell to still' another plant that may make still other products. There is a considerable return of tin in the form of waste products from chemicals sold to the silk industry. Even tin plate does not represent an ultimate use of tin because the tin-can maker produces large amounts of clippings, which are sold to detinning plants, where the tin is recovered and used again for some other purpose. Thus the degree of duplication in consumption statistics depends on the point in the industrial cycle where consumption is measured.

Jan 1, 1936

By F. J. Palumbo

Effective recycling or disposal of flue dusts is a continuing problem for copper, brass, and bronze smelters. Over 300,000 short tons (st) of dust is generated annually by U.S. secondary copper, brass, and bronze smelters. The Bureau of Mines has developed an alkaline leach method for recovering metal values from copper converter flue dust containing zinc, tin, lead, and copper. The dust was leached with a hot solution of ammonium chloride and ammonium hydroxide to solubilize ZnO. All of the tin (as Sn02) and the metallic copper, lead, and zinc, as well as possible insoluble compounds of each, report to the residue. Dissolved copper and lead salts are removed from the leachate by cementation with granular zinc. Zinc oxide is precipitated by diluting the leachate with water. The tin-rich (9.8 pct) residue has a ready market. The cement product is recyclable to the smelting operation. The ZnO is at least 97 pct pure and has potential marketability.

Jan 1, 1985

By Dean H. Ambrose

The U.S. Bureau of Mines recently developed computer graphics simulations to characterize mining scenarios, specifically for room-and-pillar mining operations in a three-entry longwall development section. These simulations compare productivity between shuttle car and continuous haulage systems concepts. One of the continuous haulage systems concepts has bolting capabilities that supplement haulage function. Simulations showed the continuous haulage system to be more time efficient than the shuttle car system. Researchers can reuse the simulation code (e.g., mining rates and equipment capacities can be changed) should investigators care to compare production of other mining scenarios. computer simulation, found computer model modification flaws and mining scenario conceptual errors. The fundamental rationale for three-dimensional computer is to cheaply, easily, and quickly obtain information about operation and of a current or proposed mechanical coal or metal/nonmetal mining system. This report documents the computer graphics model and simulation developments and discusses some of the results and observations from the simulations.

Jan 1, 1994

By R. L. Grant

The Bureau of Mines applied automatic computational methods to analyze the degree of correlation between sound transmission and atmospheric conditions. Statistical analysis of data collected over a 5-month period indicated that the following weather variables, listed in order of decreasing importance) have a significant effect on the transmission of sound in the atmosphere: 1. Wind velocity and wind direction. Winds in the direction of travel of the sound wave increase the sound intensity and duration. 2. Barometric pressure. High pressures are related to low sound intensities and durations. 3. Atmospheric temperature. High temperatures are related to low sound intensities and durations. Inversion of the atmospheric temperature did not appear to affect sound transmission under the conditions of this study.

Jan 1, 1967

By R. E. Siemens

A process is being developed by the Bureau of Mines to selectively recover nickel and cobalt from low-grade domestic laterites. In laboratory evaluation of the process, the oxides in the laterite were selectively reduced with carbon monoxide at temperatures from 350° to 600° C. For material containing more than about 5 percent magnesia, pyrite additions or post-reduction heat treatments were necessary to achieve satisfactory nickel and cobalt extraction for this range of reduction temperatures. Multistage leaching of the reduced material at ambient temperature and pressure in the presence of oxygen, ammonium sulfate, and ammonium hydroxide extracted up to about 90 and 85 percent of the contained nickel and cobalt, respectively. The nickel was selectively recovered from the leach solution by solvent extraction and was then stripped from the loaded organic with dilute sulfuric acid to provide a nickel-rich electrolyte. Treatment of the raffinate with hydrogen sulfide resulted in the recovery of cobalt as a sulfide. The only contaminant in solution was magnesium which was removed by ion exchange or precipitation. In this process the energy requirements are relatively low and except for minor operation losses, only coke and oxygen are consumed.

Jan 1, 1975

By A. S. Peck

This report presents the results of a cooperative study between the Bureau of Mines and the University of Utah to define the mechanism involved in the adsorption of oleic acid and sodium oleate on fluorite, calcite, and barite, using an infrared spectrophotometer for identifying and measuring the adsorbed reagents and reaction products. Fluorite, calcite, and barite react with oleic acid and sodium oleate in a water system, forming chemisorbed and solution products. The chemisorbed species is a surface mineral cation-collector anion salt, Chemical analysis of solution resulting from the adsorption reaction indicates that the adsorption process causes displacement of mineral anions, namely, fluoride, carbon ate, and sulfate from the surface of these minerals.

Jan 1, 1963

By F. R. Cattoir, T. A. Sullivan

Commercial uranium metal was electrore fined to a high- purity product using molten- salt electrolytes in an inert atmosphere cell . Electrorefined uranium that contained , after consolidation , less than 30 ppm of metallic impurities was prepared . A method of leaching the electrolyte crystals to remove the salts was developed . Cathode current efficiencies from 90 to 100 percent were obtained . Two molten- salt electrolytes were prepared and evaluated : (1 ) lithium chloride - potassium chloride - uranium trichloride and ( 2 ) sodium chloridepotassium chloride - uranium trichloride . Very little difference was found in the purity of the uranium metal produced in either system . The lithium chloride - potassium chloride - uranium tri - chloride electrolyte was preferable from an operational standpoint .

Jan 1, 1964

By Thomas H. Dubaniewicz

The National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory, conducted a study of past mine explosions to identify the ignition locations and ignition sources responsible for the most severe explosion events resulting in death. Since the Scotia disaster of 1976, many fatalities from underground coal mine explosions have been linked to nonpermissible electrical equipment ignition sources located in intake air courses. With few exceptions, explosion protected equipment is generally not required in intake air courses of gassy underground coal mines in the US. Cigarette lighters were another prevalent ignition source for fatal explosions ignited in intake air courses. Several mine rescue/ recovery teams have encountered electrical ignition hazards. The study provides evidence that intake air courses of gassy underground coal mines fit the description of certain Hazardous (classified) locations described in the US National Electrical Code®. Class I Division 2 or Zone 2 explosion protection tech¬niques may be used to design intake air equipment so that it does not present an ignition source under normal operation, before mine power is shut down in emergency situations. Nonpermissible circuits in intake air courses that are likely to remain energized during emergencies, e.g. battery powered equipment, should be protected by more stringent Class I Division 1, Zone 1, or Zone 0 techniques, to protect rescue/recovery personnel.

Jan 1, 2009

By D. A. Wilson

Several promising systems for selectively oxidizing the iron in an iron-tin alloy commonly called "hardhead" were investigated in a research project conducted to devise a method for recovering tin from this troublesome alloy. A satisfactory oxidation method was developed and tested successfully on melts of 2,000 grams. Molten hardhead (near 1,080° C.) was blown with air to oxidize iron and leave tin in the reduced state. Recovery of available tin was 96 to 98 percent. Tin products contained 2 to 0.1 percent iron which was reduced to 0.06 percent by filtration at 250° C. Iron oxide formed during oxidation was absorbed by a fluid flux cover composed of 43 percent silica, 17 percent burned limestone, and 40 percent fused borax. Less successful but nevertheless promising results were obtained with mixtures of steam and hydrogen which were sufficiently selective at temperatures between 600° and 950° C. but did not result in complete oxidation of iron. Carbon dioxide-carbon monoxide mixtures also oxidized iron selectively but incompletely. Both stern and carbon dioxide systems produced sufficiently encouraging results to additional research on these systems.

Jan 1, 1961

By Kenneth B. Higbie

Expenditures to advance scientific technology in general reached an all time high in 1965 with some $22.2 billion estimated to have been allocated by government and industry. Federal Government expenditures were estimated at $15.4 billion, with almost 90 percent of the funds devoted to programs involving defense, atomic energy, and outer space efforts. With this massive effort in the United States and a very impressive effort elsewhere in the world, there is little wonder that many new metallurgical developments were announced in the technical press during the year. No effort has been made to cover all aspects of the industry, but a few of the developments are described in this chapter.

Jan 1, 1966

By D. E. Emerson, C. G. Kirkland, E. M. Frost

An apparatus has been developed for determining the helium content of gases containing 40 percent or more helium . It utilizes activated coconut charcoal at liquid nitrogen temperatures to adsorb constituents other than helium in the mixture . Series of analyses have been run where the mean deviation was less than 0.05 percent helium . Twenty or more analyses can be made in an 8- hour day .

Jan 1, 1964

By Floyd G. Anderson

Owing to the rapid growth of the perlite industry in recent years, the Bureau of Mines has received numerous requests for information relative to the possible harmful effects of breathing dust resulting from the processing and use of perlite. As published information on the composition of perlite is rather meager, consisting chiefly of conventional chemical analyses, samples of crude and expanded perlite from 9 deposits in 6 Western States were studied. Crude perlite ores were examined petrographically and analyzed by chemical, spectrographic, and X-ray-diffraction methods. Sized crude and expanded perlites were analyzed chemically for total free and combined silica content.

Jan 1, 1956

By M. S. Oudenhoven

This Bureau of Mines investigation was conducted to obtain an experimental solution of stress changes in the vicinity of a circular opening in an infinite plate. Plates were stressed biaxially in compression and subjected, by four different-length shoes, to a uniform pressure at opposing points on the opening periphery. The principal stresses along the vertical and horizontal axes, which result from peripheral pressure, were obtained from the photoelastic analysis of four frozen-stress epoxy models. These principal stresses were then super-imposed on the mathematically determined principal stresses (along the same axes) obtained from a theoretical biaxial stress field in which the magnitude of the lateral pressure was one-third that of the vertical pressure. The results indicate that an increase in shoe length increases the radial compressive stress and the tangential tensile stress (except tangential compression at r/a = 1, which exists for all shoe lengths). Also, a partial control of the stresses within one-half radius of the opening surface is accomplished by a change in the magnitude and placement of peripheral pressure.

Jan 1, 1966

By John J. Sammarco

This U.S. Bureau of Mines report describes the research effort and results for a computer-assisted appendage control system of a Joy 14CM continuous mining machine. The cutter head (shear), gathering head, conveyor, and stabilizer jack are the appendages. Positional control of each appendage is accomplished by specifying the desired position to the appendage control computer, which uses appendage position sensor data. Appendage movement is actuated until the desired position is attained as determined by control algorithms. A description of the sensors, mechanical and electrical interfaces, data acquisition and control (DAC) system, experimental method to determine appendage response characteristics (range of motion, start and stop delay times, and movement rates), and their application to the position control loop algorithms are presented. Also, the test results for the shear in an unloaded (free space) and loaded (cutting) condition of the shear are presented.

Jan 1, 1991