Search Documents

By J. R. Thoenen

This circular is part 3 of the third paper (entitled "Excavation") of a series summarizing the technical problem; involved in the production and preparation of sand and gravel. Part 1 discussed the use of power shovels, draglines, and excavator cranes. Fart 2 discussed the use of power scrapers, slackline cableway excavators, and hydraulic monitors. This circular discusses the use of the hydraulic, clamshell, ladder, and dipper dredge. Part 4 to follow will discus the use of haulage equipment, and subsequent parts will discuss the application of both excavating and haulage equipment to various types of deposits. HYDRAULIC DREDGE Judged by the number of installations and the tonnage produced, as recorded in part 1 of this circular, the hydraulic or pump dredge is the most popular type of underwater sand and gravel excavator.

Jan 1, 1935

By John E. Rourke, O&apos

This report documents the process of site selection, instrument installation, data acquisition, and preliminary data analysis followed to characterize the physical response of overlying strata to longwall mining. A system of surface, subsurface and mine level instrumentation was installed at the Allen Mine in Weston, Colorado where the overburden varied in thickness from 600 to 900 feet. Survey monuments, automatic-recording strain-meters, multi-point rod extensometers, inclinometer-extensometers, stressmeters and tape extensometer convergence stations were installed to monitor displacements and stress changes. A preliminary analysis of the data acquired up until project termination has shown the system to be operative and strata response to be similar to that reported for other subsidence monitoring case histories. Recommendations for continued monitoring of the instrumentation systems are presented.

Jan 1, 1982

By H. L. Anthony, A. C. Richardson, G. D. Coe

"INTRODUCTION The Warrior View mine of the Seaboard Coal Corporation is located in Tuscaloosa County on the Warrior River about 14 miles northeast of Tuscaloosa, Ala. The Brookwood bed at this point yields a coal with fair coking qualities, and the product from neighboring mines on this bed has been used for the manufacture of blast furnace coke. The output of the Warrior View mine, however, is used exclusively for domestic and steam-raising purposes.This paper continues the series° of reports on the washability of Alabama coals which are based upon the study of coal preparation in Alabama now being conducted by the U. S. Bureau of Mines and the University of Alabama with the cooperation of the different coal mining companies. This paper contains screen-sizing and float-and-sink tests of a representative sample of run-of-mine coal, and flakiness and crushing tests on certain sizes.Published information on the Brookwood bed is very meager. Fieldner6 gives the proximate and ultimate analyses for a number of seam samples taken from representative mines working this bed. Gandrud and Britton7 show sections of this bed taken at Searles, Ala. They also give the specific gravities of the coal, the bone, and the shale partings.Table 1 give the proximate and ultimate analyses for the 3/4 to 3/16 inch size of raw coal. Table 2 gives the sulphur content and the ash fusibility temperatures of the float-and-sink fractions for this same size. The character of the coal is very uniform throughout the range of sizes produced and, as it was not convenient to have these analyses on all sizes, this size was chosen as being representative of the coal. From the information available it is evident that the coal preparation problem is restricted to one of ash reduction.SAMPLING AT THE MINEAt the Warrior View mine the run-of-mine coal is dumped from the mine cars upon a 3-inch grizzly. The oversize is crushed in rolls set at 24 inches and joins the undersize before being elevated to the raw-coal bin ahead of the jig. The sample was caught at the point where elevates discharges into the raw-coal bin, by taking a proportional amount of the coal at 10-minute intervals over the period of a day's run, The total sample amounting to 2.7 tons was shipped to the laboratory at Tuscaloosa for the washability studies."

May 1, 1932

By Michael J. Beus

This Bureau of Mines report describes a tunnel stress relaxation gage (TSR) developed to measure initial radial displacement around full-sized underground openings. The TSR technique was shown to be a valid concept in previous field verification tests. Sensitivity has been improved by employing a titanium alloy cantilever in the transducer head, which also permits a deeper sensor location. Use of improved fabrication methods such as stainless steel bellows and sputtering techniques and use of an environmental chamber for testing greatly increased overall reliability. A miniature data acquisition system (DAS) was interfaced directly to the transducer for increased versatility and containment entirely within a borehole. The present TSR system is suitable for use around full-size underground excavations, particularly machine-bored openings. Field evaluation of the improved instrumentation verified the design goals.

Jan 1, 1978

By Lowell B. Moon

The Stange and Byrnes Heirs manganese mines, adjoining properties in Bland and Giles Counties, Va., have produced at least 20,000 long tons of concentrates containing 8,000 long tons of manganese. They were selected as the site for a strategic-mineral development project because of the existence of geologic possibilities for extensions of the known ore body. In plan, the long dimension of the ore body parallels the axis of a major anticline. Localization apparently is due to longitudinal and transverse fracturing incident to two-way folding. That the manganese oxides were deposited by downward-moving solutions is suggested by the fact that mineable concentrations are confined to a coarse, porous sandstone under-lain by impervious silt and clay. Bureau of Mines project work began on January 15, 1941, and was completed on April 23. The work sampling the faces of the pit, bulldozer trenching, and churn drilling. Pit sampling consisted of 132 channel samples usually 5 feet long and taken at 20-foot intervals. Seventeen trenches aggregating some 4,500 feet in length were dug by the bulldozer. Trenches averaged 12.6 feet in width and 5 feet in depth. A total of 1,978 feet of churn drilling was done in 33 holes. In preparation for churn drilling it was necessary to construct roads to 21 of the 33 sites. A total of 2,867 linear feet of road averaging 13 feet in width was built.

Jan 1, 1950

By Arnold M. Lansche

DOMESTIC OUTPUT of white arsenic, As2O3, was derived entirely as a byproduct of smelting arsenic-containing copper ores by The Anaconda Company at Anaconda, Mont., and American Smelting and Refining Company at Tacoma, Wash. Arsenic metal was not produced. Consumption, and Uses.-Most of the white arsenic produced in 1964 was consumed in manufacturing lead and calcium arsenate insecticides. In the 12 year period since 1951 the production of lead arsenate insecticide has varied between 7,800 tons and 4,900 tons, indicating that lead arsenate has maintained its position in competition with organic insecticides.

Jan 1, 1965

The United States Bureau of Mines is establishing a computerized mineral inventory system to help the Federal Government appraise its mineral position and prepare programs insuring against critical shortages of materials. This system, called the Minerals Availability System (MAS), is a component of the Bureau's minerals intelligence function designed to conduct and maintain an inventory of minerals important to the Nation. The MAS defines the physical and commercial availability of the mineral resources. Known resources are evaluated and classified by deposit for entry into a computer storage and retrieval system. An integral concern of these evaluations is the cost of mining and beneficiating the ore contained in specific deposits. To meet this concern, a cost handbook was developed as an aid to preparing feasibility-type estimates for capital and operating costs of mining and primary beneficiation of various types of mineral occurrences. Cost data, obtained from U.S. and Canadian companies, were used as the basis of this handbook. The handbook presents cost curves and equations for each component of the mining and beneficiation process. Factors for each cost component are also given, thereby allowing the updating of cost for time, geographic location, labor rates, and mining and milling conditions. Included in the latter conditions are items such as the length of haul, need for rock bolts, and a rock work index for ores and rocks of various hardnesses. 1.2. USE OF THE HANDBOOK Using the handbook a feasibility-type estimate falling within 25% of expected actual cost is obtainable by summarizing cost components. This handbook should not be used to determine the cost of any single component of a mining or beneficiation system, as any single component may not fall within the 257 limit. It must be understood that anyone who uses the handbook must have a comprehensive knowledge of mining and processing technology and cost estimating procedures. The handbook was intended to be used internally by the Minerals Availability System. Because

Jan 1, 2012

By J. T. McCartney

OPTICAL PROPERTIES of U.S. coals of differing rank have been investigated by the Bureau of Mines, for about 20 years. These investigations have been remade to further the development of an objective basis for petrographic analysis of coal and to add to knowledge of the structure and composition of coal and coal components by determining their optical constants in various regions of the electromagnetic spectrum. Various experimental techniques have been used in these studies, including determination of reflectance from bulk specimens and transmittance of thin and ultrathin sections, interferometry, electron microscopy, and election diffraction. Similar studies leave also been made of graphite, the end product of coal metamorphism. The bureau of Mines conducted the first U.S. investigation of reflectance properties of coal components, laying the foundation for petrographic analysis based on arbitrary reflectance classes and for automated reflectance analysis of coals. Optical constants of coals of differing rank and of graphite have been determined in the ultraviolet-visible-near infrared spectrum. Maxima in the optical constants of graphite were observed in the ultraviolet region and were interpreted to be related to transitions of electrons between the valence and conduction bands. Similar maxima for coals, especially high-rank coals, appeared to be characteristic of the presence of graphitelike layers. A special application of optical theory to absorbing, anisotropic materials like graphite and high-rank coals has been developed. Electron microscopic and electron diffraction studies of coals have revealed various ultrafine structures in coal components and have shown the evolution of an oriented, crystalline graphite structure in high-rank coals.

Jan 1, 1967

By H. A. Doerner

"Statistics show3 that in 1927 the United States consumed 60 per cent of the world's production of chromite and produced none. The uses of chromium are rapidly expanding, and a dependable supply is essential to our industries. Since the political and commercial control of our supply of chromite is now in foreign hands it is prudent to determine how this nation can best prepare to supply its need for chromium if the imports were cut off or restricted and whether it is now possible and desirable to stimulate production of chromium from domestic deposits. We have only small amounts of chrome ore of high enough grade to meet present trade requirements. Therefore the Bureau of Mines is making a study of methods for beneficiating our low-grade ores.Chromite (Cr203.Fe0), is the only commercial source of chromium. For refractories, a minimum of 40 per cent Cr203 and a low silica content (5 to 8 per cent) is usually specified. In most instances bricks or lumps having a physical structure that will not crack when heated are required. The only way an inferior ore could be adapted to this use world be to concentrate it and develop a satisfactory binder to make bricks out of the concentrates.For making ferrochrome the requirements are a minimum of 45 per cent Cr203 and an iron content not exceeding one-third of the chromic oxide. On some low-grade ores gravity concentration will give a product meeting these requirements; other ores yield concentrates containing too much iron or other impurities to be saleable."

Jun 1, 1930

By P. R. Tisot

Structural response and/or deformation was determined for each of four different grade Green River oil shales (27.0-, 34.5-, 45.5-, and 63.5-gal/ton) as they were heated in an inert atmosphere, under constant compressive stress, from ambient to subretorting temperatures; that is, below those required for rapid pyrolysis of the organic matter. Small cores and small columns of confined fragments comprised the test specimens, which were heated, in a specially designed microunit, at a uniform rate either to 725° or to 825° F under three different stress levels, 80, 200, and 325 psi. Structural response of some cores was observed as they were heated in a stress-free environment. The obtained stress-strain-time-temperature relationships provide information regarding the oil shale's yield temperature, yield stress, rate of compressive strain, loss of mechanical strength, and nature of structural deformation. Effects of structural deformation on induced permeability in small columns of fragments are presented. Results indicate that underground retorting of Green River oil shale may be seriously impaired through loss of induced permeability brought about by structural deformation of rich oil shale under the influence of heat and compressive stress.

Jan 1, 1971

By S. H. Ash

THE MAGNITUDE of the anthracite industry's drainage problem in the Lackawanna River drainage area is realized when it is known that in 1948 the 27 pumping plants in this region pumped over 48 billion gallons of water to the surface from the mines in the Lackawanna Basin of the Northern field. This is almost 92,000 gallons per minute pumped against an average hydrostatic head of over 300 feet for that year. By comparison, Lake Wallenpaupack, the largest artificial body of water lying wholly in Pennsylvania, contains 71 billion gallons of water in its 24-square-mile area: the volume of water pumped from the mines in the Lackawanna Basin during 1948 was approximately 68 percent of that impounded in Lake Wallenpaupack. The Lackawanna. River and its tributaries drain a troughlike area of 345 square miles. The synclinal axis of this trough lies within the coal measures. All surface drainage into the valley must traverse some part of the coal measures. On the basis of 45.03 inches of rainfall recorded by the Scranton station of the United States Weather Bureau for 1948, the runoff from the Lackawanna River drainage area during that period was 135 billion gallons, approximately three times the volume of water pumped by all mine pumping plants in the Lackawanna. Basin of the Northern field during 1948. In other, words because of the pervious condition of the strata overlying the mine workings, approximately one-third of the total runoff in the Lackawanna River drainage area becomes mine water. This report, reveals that less than 7 percent of the 72 miles of pervious stream beds examined between Archbald and Pittston have been unproved.

Jan 1, 1952

By Arcy, D&apos Banister

The productive potential of the Nation's principal active and inactive silver mining districts has been evaluated, using 1964 economic conditions and assumed silver prices ranging up to $3 per ounce. On this basis, the United States has an estimated 5 billion ounces of unmined silver, excluding minor byproduct silver in gold deposits. Approximately 3.5 billion ounces are contained in deposits requiring higher silver prices to be economically minable, and about 1.3 billion ounces are in currently operating mines. An analysis of silver consumption trends since 1954 indicates that the free world industrial market will climb to nearly 800 million ounces annually by 1985. U.S. industrial silver consumption has been projected to increase at an annual rate of 4 percent from 1965 to 1985. Average annual increase for the remainder of the free world has been 8.1 percent since 1953; this is expected to level off with an estimated average increase of 5 percent to 1975 and 4 percent from 1976 to 1985. Foreign silver production has, in the past, exceeded consumption, but in 1960 the supply deficit was over 100 million ounces. U.S. production, also traditionally exceeding demand, was suddenly overtaken at the start of World War II. By 1964 the annual deficit, excluding coinage, was over 84 million ounces. World coinage requirements of silver are fast declining and expected to total only 25 million ounces annually by 1985. In fact, coins are already becoming major short-term source of silver to fill the large deficit between industrial demand and current production. The larger, long-term deficit (to 1985, the limit of this study) must be balanced by silver from the hoards and new production from silver deposits. Eventually all of the deficit must be met by new production or silver prices will rise until consumption is greatly curtailed. To balance free world supply and demand, it is estimated that the free world must produce an additional 85 million ounces by 1975 and 375 million ounces by 1985. The estimated proportion expected from U.S. deposits is 17 million ounces by 1975 and 74 million ounces by 1985.

Jan 1, 1969

By A. C. Johnson

This circular is one of a series published by the Bureau of Mines describing mining and beneficiation methods and costs at various mining operations throughout the United States. Inclusion of the Abbott mine in this series is of particular interest, as the complex geology and the character of the deposits make their exploitation a unique operation. The mine operates on a high-cost, comparatively small-scale basis, and only the persistence of an aggressive management has enabled it to maintain its rank among the major mercury producers of California. Rising costs and decreasing metal prices, which continuously threaten the low profit margin, are reflected in increased efficiency of operation. This report summarizes past operations and describes, in detail, the geology and ore deposits; exploration and mining methods; and furnacing and condensing operations. It covers the entire operation from initial exploration to the actual production of mercury. Comparative production costs for 1944 and 1958 are of special interest.

Jan 1, 1962

By JeffreyS. Vipperman, Daniel R. Babich, EricR. Bauer

In response to the continuing problem of noise induced hearing loss NIHL among mine workers, the National Institute for Occupational Safety and Health NIOSH has conducted numerous noise surveys in coal preparation plants. The research, consisting of worker dose monitoring, task observations, and equipment noise profiling, was completed in eight separate preparation plants. Worker dose monitoring was conducted for three shifts in most cases. Workers experiencing higher than allowable doses were task-observed for one full shift to correlate dose to noise source(s). Finally, noise levels on all floors, and in lunchrooms and control rooms, were characterized. Results indicate that only workers who routinely spend a significant portion of their shift in the plants (away from the control rooms) are susceptible to overexposure from noise. Certain pieces of equipment (screens, centrifuges, sieve bends) are the loudest primary noise sources responsible for the worker noise exposures.

By Michael L. Boucher

Copper and nickel sulfides occurring in the Duluth Complex of northern Minnesota were examined at the Bureau of Mines, A microscopic study was undertaken to determine the mineralogy and paragenesis of the ore minerals. Eighty-two samples were taken from one deep diamond drill core located near Babbitt, Minn. Modal analyses are presented for the Duluth Complex rocks and for the are minerals in the major mineralized zone. The major sulfide minerals are chalcopyrite, cubanite, pyrrhotite, troilite, and pentlandite. Results of this investigation suggest that the mineralization is related to the structural features of the enclosing rocks: pores, open fractures, and cavities. The pyrrhotite-troilite-pentlandite assemblage is believed to have formed from an immiscible sulfide melt, probably associated with the troctolitic rocks. Most of it settled to the very porous base of the Duluth Complex, and to the other porous zones near xenoliths; small portions were trapped higher in the section. A later introduction of a copper-rich sulfide melt replaced some of the pyrrhotite-troilite and oxides, and filled in the remaining open spaces and fractures in the Duluth Complex and those of the adjacent footwall rock.

Jan 1, 1975

By J. P. Rider

Operating practices and resulting production from longwall faces are continually improving. Consequently, longwall operators are continually seeking to improve the dust control capabilities on longwalls. The National Institute for Occupational Safety and Health (NIOSH) has been conducting dust surveys at longwalls throughout the country in an effort to document the types of controls that are being used and to quantify the relative effectiveness of these controls. To date, surveys have been completed at longwalls in Alabama, Colorado, Pennsylvania, Utah, and West Virginia. In addition NIOSH has been reviewing longwall dust parameters provided by mine operators to MSHA to assess the status of dust control technology being used throughout the industry. Results from the underground dust surveys and information obtained from MSHA will be summarized in this paper to provide an update on longwall dust control technology and practices.

By Russell Levens

A strategy for prioritizing mining health and safety research by evaluating the potential for risk reduction through interventions is proposed. Mining has one of the highest incidence rates of injury and disease found in major industries. The main premise of this paper is that often the best opportunities to reduce these rates are not revealed by retrospective analysis of injury and illness data. Instead, a proactive approach is needed that accounts for risks to specific hazards that can be abated by engineering or behavioral interventions. The process proposed here begins with development of prospective interventions. The degree of reduction in risk to be expected from an intervention then is determined from statistics on the mining worker population, the expected degree of success of the intervention, and the expected change in the severity of injuries resulting from the intervention. Three disparate mining health and safety concerns are presented to demonstrate common problems in assessing risks of injury and illness and describe additional data needs. Information on events preceding injuries and illnesses and more detailed demographic data on the mining work force are needed to analyze injury and illness data more precisely. Detailed information on exposure to specific hazards is necessary to evaluate the potential for an intervention to reduce risk of injury or illness.

By T. M. Barczak, S. C. Tadolini

Pumpable roof supports provide an alternative approach to secondary support in underground mining. Unlike all other supports that are either partially or fully prefabricated prior to being transported into the mine, the pumpable support is fabricated in place in the mine entry. This reduces the underground material handling efforts and thus the injuries historically associated with in-mine support construction. On-site fabrication also facilitates application of the support in areas that are inaccessible to transportation equipment such as scoops or rail cars, making it ideal for many bleeder applications. One of the main advantages of the pumpable support is that it fully bridges from the mine floor to the roof, thereby eliminating the requirement of “topping off” the support with wooden wedges or crib blocks that soften most other support responses. This report examines the development of modern pumpable roof support technology and provides a full description of the performance capabilities of each of the support products now on the market.

By Nicholas Kyriazi, John P. Shubilla

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory, has undertaken a study to determine how well self-contained self-rescuers (SCSRs), deployed in accordance with Federal regulations (30 CFR 75.1714), hold up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSRs in the sixth phase of testing from mid-1996 to early 1998. The SCSRs were tested on human subjects and on a breathing and metabolic simulator. These results indicate that most of the apparatus, if they pass their inspection criteria, perform satisfactorily. However, the deployed CSE SR-100s exhibited significantly higher inhaled CO2 levels than new units, as in the previous phase. This will cause higher ventilation rates in most users, which will, in turn, result in higher breathing pressures, possibly causing users to prematurely remove the apparatus. CSE Corp. has developed a noise test that can identify apparatus suffering from chemical-bed degradation causing the early CO2 breakthrough. This test was added to the inspection criteria for the SR-100. In addition, several of the MSA Portal-Packs that passed their inspection criteria were found to have KO2 dust in their mouthpieces. Further investigations by NIOSH and the Mine Safety and Health Administration confirmed these findings, which resulted in the decertification of the apparatus and their removal from service.

Jan 1, 2000

The revised inspection standards or recommendations herein have been prepared for use in Federal inspection of bituminous-coal and lignite mines. They succeed a compilation of similar standards published as Bureau of Mines Information Circular 7268 in December 1943 and employed as a guide in Federal inspections since that time. Important alterations and additions have been made because of changes in mining, practice and temporary shortages of some safety equipment; moreover, several previous standards have been found not generally applicable and have accordingly been deleted. Mining methods and equipment continue to change, and new hazards and new safeguards are introduced. Consequently, these standards are subject to revision from time to time. Questions from the coal-mining industry regarding these standards and suggestions as to changes and additions thereto will be welcomed and considered carefully when the next revision is made. Many constructive criticisms from the mining industry have been considered in preparing this edition.

Jan 1, 1945