Search Documents

By David C. Peters, Robert S. Crosson

A method of error analysis has been applied to the location technique of non-linear least squares iterative inversion in order to evaluate the resolving power of several seismic array configurations with various assumed earth models and errors and inaccuracies in arrival times. The results obtained demonstrate that lateral accuracies of location are improved significantly when the depth of the miner is known. Lateral location to within 100 feet appears achievable in many instances. If it is possible to refine earth models significantly beyond what has normally been assumed in this work by the use of on-site data, or if the mine is shallow (300 feet or less), accuracies of-about 30 feet or so may be attainable. Inaccuracies in earth models of about 5% are found to contribute much more heavily to these location inaccuracies than errors of a few milliseconds in picking arrival times; however, arrival time errors of 15-20 ms or above will dominate these model inaccuracies. The expected accuracy of location is found to fall off very rapidly as the miner moves outside the array. The strength of this effect depends markedly upon the geometry of the array configuration and can be reduced by careful design. Also, as the size of the array is increased, expected location errors within the array are not altered much, but continue to match the error associated with the smaller array over a larger area (assuming that all stations can still pick up the miner's signals). Better location accuracy, especially with respect to depth control is achievable in an earth where the velocity is depth-dependent (increasing with depth) than in one which is homogeneous. This is an advantage since the

Jan 1, 1974

By D. Dolinar, T. P. Mucho

Horizontal stresses are caused by global plate-tectonic forces. During 1995 alone they were largely responsible for the closing of two longwall mines in the United States. This paper presents six case histories from Pennsylvania, West Virginia, Kentucky and Alabama. In each case, a mine encountered roof falls or difficult ground conditions at the headgate caused by horizontal-stress concentrations. The problems are detailed, and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble free. The paper also discusses detailed measurements that were made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal-stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel to the maximum horizontal stress, as previously thought, but rather it is 20° in the stress shadow of the gob. Other stress-control techniques, including artificial support, are briefly discussed.

By Manuel Gomez

A computerized moving average technique was developed to interpolate coal seam characteristics between sample points. The interpolative method coupled with multivariate regression analysis and simulation procedures was used to forecast coal properties not readily obtained from an analysis of drill core samples. Coal property forecasts were of two kinds: (1) specific mine property forecasts that are suitable for mine product control and yield a good approximation of the local variation along both the vertical and horizontal axes of the seam, and (2) regional estimates where much of the local seam variation is smoothed out, but the general trends are maintained. Forecasts of the volatile matter, ash, total sulfur, and the heating value for part of the Pittsburgh seam located in Ohio, Pennsylvania, and West Virginia were in good agreement with independent evaluation data. Spatial configuration for preparation characteristics, particularly, the effect of crushing on sulfur release, low-and high-temperature carbonization properties, the Hardgrove grindability index, the coal hardness index, gasification variables, and hydrogenation factors were constructed for the same area of the Pittsburgh seam. These forecasts may be developed from drill core data collected in the exploration phase of mining. The results, which may take the form of a series of maps, are useful to mining, chemical, and combustion engineers, to economists and mine managers, as well as to coal users for mine design, economic analyses, energy forecasts, utilization studies, mine product control, and environmental control and programming.

Jan 1, 1974

By Spencer P. Howell, J. F. Xrawshaw

"A recent premature explosion in a quarry that resulted in the death of nine men and the injury of several others, was directly traceable to a spark from a steam-shovel working under the face directly in front of the hole being loaded. This accident and similar accidents on record in the Bureau of Mines indicates the necessity for pointing out the dangers in quarries of explosives being ignited by sparks emitted from steam shovels and locomotives, and making recommendations for greater safety.Many premature explosions of which the following are examples, have resulted from sparks, both from steam shovels and passing locomotives. (A) The premature explosion occurred during August, 1920 at a limestone quarry, in a 100-foot drill hole, loaded with 1000 pounds of high-grade nitroglycerin and gelatin dynamites. This hole had been loaded with 500 pounds of 75 per cent strength gelatin dynamite, 300 pounds of 60 per cent straight nitroglycerin dynamite, and 200 pounds of 50 per cent straight nitro¬glycerin dynamite; but no steaming had been placed in the hole. The powderman loading the hole saw the spark enter the hole and was able to run a short distance before the explosion took place, thus escaping serious injury. The explosion of this first hole was transmitted to nearby hole similarly charged. The fall of rocks from these two holes buried the steam shovel and some of the gang of men working around it.(B) In September, 1909, in the Canal Zone, a steam shovel uncovered a misfired charge of dynamite. While the dynamite was being picked up the steam shovel continued working nearby. A spark from the shovel set fire to some loose dynamite spilled on the ground from the troken cartridges. This fire was transmitted to a hole which was being loaded close by and caused a premature explosion. One man was injured."

Nov 1, 1920

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

2. Preliminary Study - Initial Probing 2. 1 Introduction Initial probing of the mine passage is required prior to the emplacement of the sealant material or deployment of the seal checker system. Factors which are of interest in sealing and checking include a. size and condition of the mine passage b. location of the borehole with respect to the ribs c. the presence of water flows d. the proximity to an intersection The importance of each of these factors depends strongly on the sealant material. Because the sealant material had not been selected at the time of the initial probing study, a broad survey of probing techniques was conducted. The capabilities and limitations of each technique as they applied to probing through the borehole were identified. To facilitate this comparitive evaluation, Table I was prepared which lists all passage conditions which might affect the emplacement of sealant material in the passage. The most satisfactory techniques for observing each condition of interest are listed together with the effects of the observation on the sealing operation. Table II summarizes the environmental conditions likely to be encountered in the passage being probed and the physical

Jan 1, 1973

By R. D. Leitch

Tests have recently been conducted by the Bureau of wines on the ignition hazard of exposing heated filaments of electric mine lam bulbs in an explosive mixture of methane and air. This investigation was undertaken in order to settle a question that had arisen in connection with the safety of miners? electric lamps. For several years, in view of former studies made by the Bureau and reported in Bulletin 524, the fact that the heated filaments of even low voltage, lour candlepower bulbs constitute a danger was generally accepted by the Bureau's engineers. These early tests, as well as subsequent tests, were conducted with Pittsburgh natural was as the testing medium.

Jan 1, 1925

By S. P. Sandoval, A. E. Clark, S. W. Yopps, J. S. Gomer

The U.S. Bureau of Mines conducted Cu exchange tests for six common clays under simulated in situ leaching conditions. Regression equations were obtained from the data expressing the Cu exchange capacity as a function of Cu concentration, pH, and temperature. Using these equations, an analysis was made of the impact each clay could have on overall Cu recovery. The results suggest that Ca and Na montmorillonite clays could have a major impact on Cu recovery and that attapulgite and illite clays could have a smaller, but still significant, impact. Kaolinite and ripidolite clays pose little threat to loss of Cu from in situ leaching solutions.

Jan 1, 1992

By C. D. McMaster, John C. Hartley

Three systems that monitor ventilating fans are described . These electronic monitoring systems automatically perform most of the operations required to conform with the provisions of the Federal Mine Safety Code in the event of fan failure or slowdown .

Jan 1, 1964

By E. J. Gleim

A list of permissible mine equipment, tested and approved previous to January 1, 1942, was published In Bureau of Mines Information Circular 7207.3/ The present list covers additional equipment approved during the calendar year 1942. The items have been numbered to indicate the order in which each type of machine or device was approved in its particular classification. Thus, Information Circular 7207 gives four air compressors on the Bureau's active list, and the present circular gives the fifth to be approved. Items 90 and 94 under Loading; Machines land Conveyors also appear in Information Circular 7207. These numbers are repeated hero to show that approval was granted during 1942 for additional voltages on machines previously listed one voltage only. Equipment listed in these circulars is approved by the Bureau of Mines only when found upon inspection and test to comply with minimum standards of safety as outlined in schedules prepared on the basis of many years of experience in dealing with safety problems of the coal-mining industry. The use of such equipment in mines known to be gassy, as well as in those which may become so, is earnestly recommended in the interests of safety. This circular is published so that the industry may be kept informed as to the many types of machines, devices, and lamps that arc available for reducing explosion and other hazards incidental to coal mining. The present paper and Information Circular 7207 together give the complete list of all available permissible .Mine equipment.

Jan 1, 1943

By Gordon E. Fletcher

This Bureau of Mines report outlines the atomic absorption analysis of oilfield brines for barium, calcium, copper, iron, lead lithium, magnesium, manganese, potassium, sodium, strontium, and zinc, using the method of additions. The advantages of using atomic absorption are discussed. The method of additions was chosen to overcome large matrix interferences usually found in brines; techniques of overcoming chemical, ionization, and background interferences are also described. The method was used to analyze several hundred oilfield brines and found to be rapid and reasonably accurate. A solvent extraction method was used to concentrate lead, copper, zinc, and iron in low-level samples.

Jan 1, 1974

By W. T. Abel

The Bureau of Mines tested 48 materials for their ability to absorb H2S from hot simulated producer gas (1,000°-1,500° F). The material found best from the standpoint of absorption capacity, durability, and amenability to regeneration was sintered pellets of 75 percent fly ash-25 percent Fe203. The performance of this absorbent under simulated and actual conditions is described. The effect of absorbent composition, absorbent temperature, steam content of the gas, and tar vapors and dust in producer gas is discussed.

Jan 1, 1974

By Robert L. Crosby

The Bureau of Mines investigated the substitution of cement copper powder for commercial copper powder in an Fe-7 pct Cu-l pct C powder metallurgy alloy. Copper powders from six different commercial cementation operations were separately upgraded by screening and hydrogen reduction. They were then mixed with commercial iron and graphite powders to form the Fe-7 pct Cu-l pct C alloy. Various chemical and physical properties were determined on the upgraded cement copper and the alloy powders. Mechanical, physical, and chemical properties were determined on green and sintered specimens made from the alloy powders. Mean tensile and bending strength of sintered specimens were significantly lower than the means from specimens made from commercial metal powders. The lower strengths are apparently related to poor sinterability.

Jan 1, 1970

By A. L. Engel

This publication describes further research by the Federal Bureau of Mines in beneficiating domestic manganese ores. The ores selected for treatment were typical of many manganese deposits in California and Nevada in that they have not been economical to mine because they are low grade or contaminated with siliceous minerals and are not amenable to physical concentration.3 4/ It would be desirable to develop a simple treatment method resulting in nearly complete extraction of manganese from these ores and applicable to small-scale operations. Sulfation reduction appeared to be such a method. The studies reported in this publication were directed toward sawdust or lignin-sulfonates as reducing agents. Sawdust, as waste from lumbering, and lignin-sulfonates, byproducts of woodpulp papermaking, are comparatively cheap and may be available in areas where manganese ores are found. Sugar, oils, and coal were also tried as reducing agents.

Jan 1, 1960

Continuous remote sensing of methane concentration in underground mines. Approach A methane transducer, developed as a fixed point rib-or face-mounted operating device, measures ambient levels of methane and produces a signal that is proportional to the measured concentration. How It Works The methane transducer, developed under contract for the Bureau of Mines, uses a catalytic-type sensor which will detect methane concentration. The transducer is mounted vertically, as shown. This type of mounting minimizes dust accumulation on the sensing element, which might cause degraded operation. The unit must not be located in an area where water can continuously drip or run on It. The transducer generates an electrical signal proportional to methane concentration at the sensor. A sensor failure output indicates the status of the sensing element A circuit within the methane transducer detects whether the sensing element is shorted or open. A high signal (approximately 8 Vdc) on the failure output Indicates the sensor element is operating In Its normal range. A low output (less than 1 Vdc) indicates an element fault. The methane transducer, enclosed in a stainless steel

Jan 1, 1982

By S. E. Khalafalla

The Bureau of Mines investigated the metallothermic reduction of copper oxide as a function of temperature, reactant proportions, form of reductant, and gaseous environment, using iron and steel scrap reductants. The reaction proceeded rapidly with powdered iron at temperatures above 560° C, attaining over 95 percent copper metallization within 3 hours. The importance of inter-reactant contacts on the extent of the reaction was evident from the variable, but usually lesser, degree of metallization obtained with iron from tin cans and automobile steel scrap. Reduction decreased as the molar ratio of copper to iron increased between 1 and 3. The most favorable gaseous environment for the reaction was a static helium atmosphere containing about 0.6 percent water vapor. Ferrothermic extraction of copper from its oxides appears to be essentially a "solid-state cementation" process. While ordinary cementation processes must be preceded by leaching, the ferrothermic method avoids this generally slow step and also the water pollution caused by the leaching agents. Sulfidic copper concentrates could likewise be reduced with metallic iron following their complete oxidative roasting.

Jan 1, 1969

By A. M. Stubbs

The Bureau of Mines has devised a procedure to selectively extract and recover chromic oxide (Cr203) from waste high-temperature shift catalysts that contain approximately 6 pct Cr and 62 pct Fe, both in oxide form. The Bureau's procedure consists of roasting the waste catalyst with sodium hydroxide (NaOH) or sodium carbonate (Na2C03) followed by water leaching. The chromium from the leach liquor was recovered utilizing an oxidation-reduction reaction with pH adjustment to form a hydrous chromic oxide (Crp3oXHp) precipitate. The roast-leach procedure produced chromium extractions greater than 89.7 pct, with product recovery in excess of 99 pct from the leach liquor. The costs of the NaOH and Na2C03 roast processes, including sizing and equipment-related recommendations, were determined by the Bureau's Office of Process Evaluation. The economic evaluation indicates that producing a Crp3 product, at the present time, is not competitive with the present-day cost of imported chromites. The estimated average operating cost for both processes was $5.44/1b of recovered Cr203 concentrate. However, this procedure offers a potential alternative to the disposal of this waste through landfiIl.

Jan 1, 1988

By S. R. Borrowman

Physical beneficiation, leaching, and solvent extraction investigations were made to recover a high-grade thorium oxide product from Bald Mountain, Wyo., conglomerate. The monazite in the Bald Mountain deposit contains 8.8 percent Th02 and, therefore, is higher in thorium content than the usual domestic or foreign monazite. A sample of composited drill cuttings for the study contained 4.3 pounds of monazite per ton of are. The work showed that the monazite, although unusually fine grained and friable, could be concentrated by tabling and magnetic treatment to yield a product assaying 5.65 percent Th02 with a recovery of 61 percent of the thorium. Subsequent decomposition of the concentrate by treatment with sulfuric acid and solvent extraction of the resultant solution with a primary aliphatic amine yielded a thorium oxide product of 99-percent grade.

Jan 1, 1962

By Peter F. Steidl

As part of the Bureau of Mines methane control program, the Upper Free-port coalbed was studied in Fayette County, Pa., where this coalbed lies about 650 feet below the Pittsburgh coalbed and contains the largest remaining reserves of any coalbed in the county. Coal and overburden isopachs, structure and joint pattern maps, and a fence diagram were prepared using data from gas and oil exploration logs and coal outcrops. These maps will aid in deter-mining the need and/or feasibility of degasifying the Upper Freeport coalbed in the study area. Much of the coalbed in this area is under 600 to 1,400 feet of overburden. By correlation with data from the Pittsburgh coalbed, the gas content at depths of this order is estimated to be between 140 to 300 cf/ ton of coal, for a total of 190 to 400 billion cubic feet of methane in this coalbed in Fayette County.

Jan 1, 1977

By T. L. Hebble

The Bureau of Mines investigated a hydrometallurgical procedure to recover Co, Ni, and Cu from an electrolytic zinc industrial copper filter cake. The copper filter cake is presently unmarketable or of low value because economic and environmentally acceptable processing technology is lacking. Research by the Bureau of Mines has developed a multistage process for recovering or recycling over 93 pct of the Zn, Cd, Cu, Co, and Ni from this material. The stages involved are (1) wet sizing, (2) H2S04 leaching of undersized material, (3) H2S04-Mn02 leaching of H2S04 leach residue, (4) selective precipitation of As, Cu, and Co-Ni products, and (5) precipitation of manganese for recycling to the leach circuit. The final process residue is only 1.6 wt-pct of the initial cake and consists of lead sulfate.

Jan 1, 1981

By J. G. Donaldson

The Bureau of Mines investigated the formation of boron and boron-carbide coatings by vapor-phase reactions. Optimum parameters were determined for hydrogen reduction of boron trichloride and for the fonnation of boron-carbide coatings on graphite by reaction with the depositing boron. At 1,300° C, about 85 percent of the boron was deposited. Tungsten substrates did not react with the boron deposit; other substrates reacted to various extents. The hydrogen reduction of boron tribromide was briefly investigated. Boron carbide was deposited at 1,300° C by adding methane to the boron trichloride-hydrogen feed gas. The chemical composition of the vapor-deposited boron carbide approximated B4C. A method of etching B4C was developed to study its microstructure. When boron was deposited on graphite at 1,500° C, very hard, uniform, strongly adherent coatings of B4C were formed that might be useful in rocket nozzle applications.

Jan 1, 1968