Search Documents

By A. J. Kraemer, O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States is a continuation of a series of reports made in accordance with a cooperative agreement between the Coordinating Fuel Research (C. F. R. ) Committee of the Coordinating Research Council (C. R. C.) and the Bureau of Mines of the United States Department of the Interior . The first of these reports contained data on motor gasolines sold during the winter of 1935-36 and further reports on motor gasolines sold during the succeeding summers and winters to the summer of 1941

Dec 1, 1943

A study was conducted by the Bureau of Mines to evaluate natural gas as an automotive fuel and to provide guidelines for optimum engine adjustments for low exhaust emissions. The study was conducted using a single-cylinder engine, a multicylinder engine, and a total of eight vehicles. Results from single-cylinder engine tests showed that the light-load, lean-limit misfire region for natural gas begins at an air-fuel ratio between 150 and 160 pct of stoichiometric. Changes in ignition timing significantly influenced emissions of nitrogen oxides and hydrocarbons, but had little effect on carbon monoxide emission. Low emissions can be achieved with current-design engines by adjustment of engine parameters, but only with heavy penalty to engine performance. Emissions from vehicles fueled with natural gas are virtually unaffected by ambient temperature change within the range 20° to 100° F. The organic emissions from engines fueled with natural gas were estimated to be 22 to 25 pct as reactive as the emissions produced using gasoline. Levels of exhaust emissions from vehicles fueled with natural gas were unchanged over 10,000 miles of normal driving.

Jan 1, 1973

By B. W. Madsen

A nearly dormant copper sulfide pilot-scale experimental leach containing 8.7 tons of are was injected with oxygen to determine its effect on the copper-leaching rate. Prior treatment of the uncrushed 0.25-percent-copper, mine-run stripping material consisted of 461 days of acid ferric sulfate leaching, which extracted 47 percent of the total copper. The permeability of the bed had decreased, and the percolation rate had decreased from an initial 20 gallons to 0.8 gallon per square foot per day. Copper extraction had nearly stopped. After injecting oxygen into the ore column and leaching for 30 days, the percolation rate was increased to 6 gallons per square foot per day. In an additional 298 days of leaching, an additional 40.7 percent of the copper was extracted. The improved leaching after the use of oxygen is attributed to stimulated bacterial action, better oxidation, and increased permeability.

Jan 1, 1975

By C. C. Anderson, H. H. Hinson, H. J. Snhroeder

"INTRODUCTION The Eunice field is one of a group in southeastern New Mexico producing oil and gas from so-called limestone-type reservoirs in which the productive strata are dolomite or dolomitic limestone ordinarily, wells in reservoirs of this type show wide differences in their productive characteristics, indicating erratic variations in porosity and permeability. Often there is a large difference in total footage of actual ""pay"" penetrated in neighboring wells and the vertical distribution of the ""pay"" within the productive strata varies. In the Eunice field there are few easily recognizable geologic markers to indicate true structural conditions of the oil-productive section, due to horizontal and vertical gradation in chemical compositions and lithologic characteristics of the strata. Geologic markers are found some distance above the oil-producing zones in this field and consequently they indicate only the general structure. Furthermore, no direct relation has been found between the general structure and the accumulation of oil within the reservoir.Many problems in well-completion and production practice have been met in the Eunice field because of erratic variations in porosity, permeability, in vertical distribution of ""pays,"" and the apparent departure from ordinarily accepted relations of oil accumulation to structure. A detailed study of the position and characteristics of the oil- and gas-producing zones aids production procedure. The methods employed in studying the Eunice field, discussed in this paper, may be applicable to other limestone-type reservoirs."

Jul 1, 1939

By Joseph A. DeCarlo

This publication presents statistical data on oven-and beehive-coke plants in the United States. Information on the carbonizing capacity of the coke industry is important because of the close relationship between the coke industry and most of the other basic industries of our country. Coke is an essential-raw material in pig-iron production; also, coal-chemical materials are used to make fertilizers, paints, plastics, synthetic rubber, explosives, detergents, nylon, pharmaceuticals, dyes, and many other useful products necessary to sustain and improve the high standards of living in our country. Oven-coke plants in the United States on December 31, 1958, are tabulated in table 1. This tabular presentation shows the location, classification, number and type of ovens, annual coke capacity, coal chemicals produced, and name and address of parent company for each individual coke plant. About 86 percent of the capacity of slot-type coke ovens in the United States is owned by iron and steel companies. In most of these plants the coke ovens are integrated with the blast furnaces to facilitate transportation of raw materials for steel making. This has resulted in large coke plants, and the average annual coke capacity of "furnace" plants in 1958 was 1.3 million tons. Nonfurnace or "merchant" plants include coke plants associated with chemical operations, gas utilities, as well as coke plants that produce metallurgical, industrial) and residential-heating grades of coke and coal-chemical materials for sale on the open market. These plants ordinarily are not as large as furnace plant~ and annual coke capacity of merchant plants in 1958 averaged only 500 thousand tons. At the end of 1958 there were 55 furnace plants and 22 merchant plants.

Jan 1, 1959

By Robert W. Gordon

This report describes the results and conclusions of the further development of a lightweight probe drill for use in anthracite mines. Improvements to the drill previously developed under Contract H0282044 were made and tested at an Eastern Pennsylvania mine. These improvements were: 1. Better hole cleaning due to the development of an air-water mist flushing system. 2. The application of roof drill bits to allow drilling through rock seams and lenses. 3. The development of a quick coupling drill system which reduced total steel change time. 4. Adaptation of a swivel to the drill anchoring system which greatly reduced set-up time between holes. With these improvements the probe drill demonstrated its ability to drill the required 11 holes in one shift. It also gained miner acceptance as a viable underground working tool. The probe drill proved to meet all of the design requirements of portability, low weight drilling controllability, structural integrity and reliability. In addition to its ability to drill the required probe pattern, the probe drill has the capability of drilling long holes. By drilling several holes over 80 feet deep the probe drill has demonstrated a potential for use in robbing pillars and for methane drainage.

Jan 1, 1981

By Richard D. Miller

This Bureau of Mines publication contains analyses and related source data for 224 natural as samples from 18 States. Of the total, 191 sam¬ples were collected during calendar year 1981. The remaining 33 samples were collected during previous years, but releases, granting permission to publish were not received until 1981. All samples were obtained and analyzed as part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by the mass spectrometer and special helium apparatus described previously (1-2).3 The results of the investigation of the occurrences of helium are published annually to make the information available as soon as possible to the gas industry and the general public. Twenty-five publications have presented the results of 12,827 gas analyses made prior to 1981. The first three bulletins (1-3) contain analyses and related data on 5,218 gas samples collected from 1917 through 1960; these bulletins have been supplemented annually by information circulars (4-17, 19-24) containing 7,609 analyses of samples collected since 1960.

Jan 1, 1982

By R. H. Storch

The work described in this report was part of a Bureau of Mines program to appraise the titanium-mineral resources of Idaho. Part of the program included churn drilling of alluvial deposits that previous preliminary testing, primarily for rare minerals, had indicated to be potential sources of titanium minerals. The first spot churn drilling began in the Deadwood placer area, Valley County, Idaho, in July 1956 to determine both the amount and grade of the ilmenite, FeTi03. Ten holes, ranging in depth from 6 to 40 feet and aggregating 251 feet, were drilled; 54 samples were taken. The samples were sent to the Spokane field laboratory for concentration and visual estimation of the amounts of the more common minerals in the heavy sand concentrates. For specific determinations samples from each drill hole were composited and shipped to the Bureau of Mines laboratory in Albany, Oreg., where petrographic, quantitative X-ray spectrographic, and chemical analyses were made.

Jan 1, 1958

By Walter D. Holland

This document is one of a series of instruction guides developed to help instructors present health and safety training courses to workers in the metal and nonmetal mining industry. This course is intended to provide above ground metal and nonmetal mining employees with training which will assist them in performing their work safely and healthfully. A document entitled, "Airborne Contaminants in Above Ground Metal and Nonmetal Mining and Processing Work Areas," is used as a manual for the students during the course. The unique features of the teaching guide are thumb rules for recognizing hazardous situations, candidate contamin¬ants for each work area and descriptions of control devices and work procedures.

Jan 1, 1977

By John R. Reeves

The data presented in this paper form the chief part of a general survey of the oil-shale resources of Indiana. Other papers* have already been published which contain data an various aspects of this resource. In combination, these papers present data with reference to the following points; (1) distribution of the New Albany shale; (2) amount of shale available; (3) homogeneity and thickness of the formation; (4) amount and quality of the oil obtained from the shale; (5) nitrogen content of the shale; (6) extractibility of the shale and its amenity to breaking; (7) some economic factors bearing upon the utilization of the shale; and (3) other miscellaneous factors and data. In the future, technical work on other phases of the general problem is expected to be done with the object of making a complete survey of this resource which is of much potential importance to the state and nation.

Jan 1, 1923

By M. O. Serbousek

The load-transfer mechanics of fully grouted roof bolts in coal mines have been investigated in laboratory and analytical studies. The purpose of this Bureau of Mines research is to increase understanding and better interpret data from routine field pull tests and to develop a numerical model of a grouted bolt that can be used in a global computer model of a mine roof. Analytical studies using closed-form solutions and finite-element techniques were compared to experimental results. Laboratory work includes variation of bolt length, hole diameter, and grouL type. Pull tests were pel'fol·med on 4-, 2-, and I-ft bolts in holes of 1-and I-3IB-in diameters. Both polyester resin and inorganic grouts were used as the anchorage medium. Strain gauges were installed on the bolts at several locations to observe the rate of load transfer from the bolt through the grout to the rock mass when a force was applied at the bolt end using standard jack pull testing procedures and equipment. The average anchorage length of 4-and 2-ft bolts was 22 in. Grout type and hole size variations did not produce a significant effect on the rate of load transfer from the bolt to the rock.

Jan 1, 1987

By Anthony T. Iannacchione

The Bureau of Mines developed data on the methane content of the Hartshorne coalbed, Haskell and Le Flore Counties, Okla. The methane content is calculated to be between 1.1 and 1.5 trillion cubic feet, based on an estimate of total coal in place of 2.4 to 3.2 billion short tons. Methane increases with depth, but the rate of increase decreases with greater depths. Degasification in advance of mining is recommended for all mines operating at depths greater than 500 feet to reduce hazards and methane explosions, decrease mine ventilation costs, and conserve the natural gas that would be otherwise wasted.

Jan 1, 1979

By Michael Sokaski, M. R. Geer, H. F. Yancey

This report is one of a series describing investigations by the Federal Bureau of Mines of the performance of various types of coal - cleaning equipment ; other reports in the series are listed in the bibliography . The information in these reports is useful to the coal industry and the manufacturers of coal - cleaning equipment in several ways : First , it assists the coalpreparation engineer who is planning a new plant to select the type of process best suited to the requirements by enabling him to forecast the yield and quality of clean coal obtainable with each type of equipment . Second , the information serves as a yardstick by which the performance of a plant can be judged and thus helps determine whether it is operating at satisfactory efficiency . Both these functions promote better coal - preparation practice ; that is , they help provide coal of more suitable quality for the market and likewise minimize the waste of good coal . This serves the interest of conservation with which the Bureau is vitally concerned . The present report deals with three plants using the Tromp dense - medium process , named after its inventor , K. F. Tromp , who developed the process in the Netherlands in 1936.5/ Selection of this particular dense -medium process for investigation was entirely a matter of convenience , and reports dealing with other dense -medium systems are planned for the future . Two baths are employed in one of the plants investigated . The first of these , handling 6- to 3 - inch coal , exhibited an exceptionally sharp separation between coal and impurity . This was characterized by an error area of 12 and a probable error of 0.023 . In the second bath , treating refuse from the

Jul 1, 1960

By T. A. Lang

The objective was to develop a Program Plan of analytical studies and tests for determining (1) the optimum installation tension of a coal mine roof bolt, (2) the most valid bolt support theory or theories, and (3) the most valid roof failure theory or theories. On this basis a comprehensive literature search was made and significant material dealing with coal mine roof behavior, roof bolting and roof support was collected, reviewed, classified and analyzed. Emphasis was given to the influence of rock reinforcement on the control of deformation, stress field modification and mine roof stability. An assessment was made of the effect of various parameters including bolt tension, bolt pattern and time of installation, on the effectiveness of rock reinforcement systems, and equations developed for bolt tension as a function of these parameters, and rock properties. From these studies, a major program plan of tests and studies was developed for verifying and validating the most tenable theories of roof behavior and roof support and for determining optimum bolt installation tension.

Jan 1, 1979

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States is a continuation of a series of reports made in accordance with a cooperative agreement between the Coordinating Fuel Research ( C.F.R. ) Committee of the Coordinating Research Council ( C.R.C. ) and the Bureau of lines of the United States Department of the Interior . The first of these reports presented data on motor gasolines sold during the winter of 1935-35.4/ Further reports have been issued describing motor gasolines sold during the succeeding summers and winters to and including the summer of 1941.5/ No reports were made on motor gasolines sold during the winter of 1941-42 and during the summer of 1942 . However , starting with the winter of 1942-43 , the semi - annual reports have been resumed

Jan 1, 1945

By Rogers F. Davis

This publication has been prepared to supply manufacturers and industrial users a listing of mobile diesel-powered equipment and subassemblies approved and certified by the Bureau of Mines for use in noncoal mines. Testing of diesel-powered equipment is one phase of the Bureau's program of health and safety that concerns approval of electrical and diesel equipment designed to prevent explosions, fires, shocks, or toxic hazards in underground mines, when such equipment is used and maintained properly. Manufacturers submit machinery and component parts to the Bureau for study of their design, safety features, and use. Equipment must pass exacting tests and must meet strict requirements established through research and experience and listed in the Bureau's permissible schedules before the Bureau approves it as permissible for safe use in mines.

Jan 1, 1963

By Jr. Allan

"Although the advantages of large-capacity air receivers for underground mines are plainly evident from published information about various installations in the United States and abroad, details of their construction are not generally known in this country., Ordinary present-day air-compressor installations servicing mining machines are designed to supply air at a specified pressure in sufficient quantity to meet the peak demand of the mine,2/ although this demand may exist for only a few minutes out of 24 hours and, as usually happens, eventually exceeds the capacity of the compressor. Most of the receivers provided with these compressors (to a certain degree of standardi¬zation) are capable of storing a volume of air approximately equal to that compressed in 1 minute by the machine.3, 4/ As a result, during peak-load periods the compressor operates at full load capacity without maintaining kick-off pressure. At other periods of the work cycle, production of compressed air is intermittent.At least one large mine5/ has adopted large-capacity receivers to reduce wear on its air-compressing system caused by the sudden demand of peak loads. Under the old system, the compressors jumped suddenly from half speed to full speed; boilers furnishing steam to the compressors were taxed heavily to provide the increased requirements of power; and machines using the air, among which were four large hoists, were required to operate at 65 pounds per square inch rather than at the 90 pounds per square inch for which the compressors were regulated. Operation of air machines, especially drills, at pressures lower than those for which they were designed decreases their efficiency and increases maintenance costs. In addition, air that comes directly from the compressors has had little opportunity to cool and dry enroute.6./ As a result, quantities of compressor lubricant and water are carried into the machines that use the air. When expansion occurs in the cylinder or turbine of such engines, the temperature of the air drops, and this oil and water is precipitated. The water washes away lubricating oils in the machine, causing poor performance and high cost of maintenance; the compressor oil, in addition to being a poor lubricant for compresed-air engines, exerts a corrosive action on gaskets and rubber hoses.7/Reduction of peak demands on air compressors by large receivers lowers power costs by establishing more nearly constant load factors,8/ and in some cases by permitting the use of smaller compressor capacity.8,9/Load factor is the ratio of average demand to maximum demand; a low load factor costs money.10/Elimination of high-peak demands raises the load factor by making the average and the maximum demand more nearly equal. Further savings may be made possible by large receivers where their use permits charging to be done at night in regions having lower power rates during that period.11/Where ordinary receivers are used, compressor breakdowns cause immediate work stoppages in the mine owing to lack of air. Similarly, the capacity of a large receiver has been known to permit uninterrupted work in the mine until the compressors have been returned to service.9/Large-capacity receivers, either steel-tank or underground rock-chamber, offer a practical solution of many existing problems by providing a sufficient reserve of compressed air within the pressure range required for efficient operation of machines to level off peak demands on the compressor. The com¬pressors operate when the demand has reduced the pressure in the receiver below the regulating pressure and until all air used from the receiver has been replaced. It has been found possible in at least two mines,8.9/ one of which the author has visited, to entirely eliminate one compressor and to obtain more efficient performance from the remaining one by the construction of an underground coal-chamber receiver.8/"

Jan 1, 1950

By D. E. Sullivan

The Minerals Availability Program of the Bureau of Mines conducts cost evaluations of current and potential mineral operations in the United States and foreign countries. The International Mining Cost Indexation System (IMCI) allows data of different time periods within a country to be updated to a common base year for analytical purposes. The IMCI comprises 12 factor cost indexes and an exchange rate series for 96 market economy countries, denominated in both local and U.S. currency. The IMCI for each country contains 12 time series indexes that measure the average annual rate of change in the cost of factor inputs to the mining industry within that country. Mining industry factor cost indexes include wages, plant and equipment, construction and mining materials, power and transportation, and other measures considered to comprise the majority of capital and operating costs. Cost data or proxies are collected in local currency. Index series within each country are constructed separately and indexed on a 1975 base year. The local currency index is converted to a U.S.-dollar-based currency index using an exchange ratio.

Jan 1, 1987

The objective is to provide effective training on refuge chambers for underground coal miners. This training will increase knowledge about how to teach miners to operate, transport, and inspect a refuge chamber; what to expect psychologically and physiologically inside a refuge chamber; and how to decide when to use a refuge chamber. Background During 2006?2007, several disasters occurred at U.S. underground coal mines, resulting in 28 fatalities. These disasters led to new approaches to mine safety and health, as well as new federal regulations. One new technology mandated by federal legislation is the refuge chamber. Refuge chambers are movable shelters that are either made of steel or inflate from a steel skid as a tent. They can potentially save the lives of miners during an underground mine emergency by providing breathable air, food, water, and a safe environment for up to 96 hours. Because the refuge chamber is a new technology, recommendations, information, and training products are greatly needed.

Nov 1, 2009

By Michael J. Brnich

On November 20, 1968, a massive explosion rocked the underground workings of Mountaineer Coal Co.?s Farmington No. 9 Mine in West Virginia. Of the 99 miners who were working in the mine at the time of the explosion, only 21 survived and escaped the mine. This group included eight who were rescued from the Mahan?s Run air shaft. Nearly 40 years after the event, researchers from the NIOSH Pittsburgh Research Laboratory conducted oral history interviews with two of the eight survivors rescued from the shaft. The Farmington No. 9 Mine disaster ultimately led to passage of the Federal Coal Mine Health and Safety Act of 1969 (amended in 1977).

May 1, 2009