Search Documents

By A. R. Taylor Jr.

The heat capacities of a-quartz form beryllium fluoride were measured at approximately 3° intervals from 8° to 300° K., using an adiabatic calorimeter. At 298.15° K the heat capacity and entropy were 12.39 cal/deg mole and 12.75 ±0.04 eu respectively. Enthalpy measurements were made with an ice calorimeter at approximately 30° intervals on the quartz and glassy forms of beryllium fluoride between 300° and 1,200° K. A melting point of 825° K and an 0,-8 type transition at 500° K with a heat effect of 75 ca1/mole were deter-mined from the enthalpy data for the quartz-type sample. Beryllium fluoride glass crystallized spontaneously into the quartz modification at 500° K. The heat of the reaction BeF2 (a-quartz) .... BeF2 (glass) was found to be 1,125 ±16 cal/mole at 298° K by solution calorimetry. This value, when corrected to 273° K, was used to correct for the heat absorbed by the formation of glassy BeF2 when the sample was dropped into the ice calorimeter from temperatures above the melting point. Using corrected enthalpy measurements, the heat of fusion was determined to be 1.13 kcal/mole at 825° K.

Jan 1, 1965

By B. W. Naugle

This report describes the carbonizing properties of coals from the principal beds in Cambria County, Pa. Samples of coals from Upper and Lower Freeport and Upper and Lower Kittanning beds having estimated minable reserves of 50-million tons or more were studied by the Bureau of Mines. Cambria County coals rank either as medium-or low-volatile bituminous. A preparation study indicated that all coals tested in this county, except one sample from the Lower Freeport bed, were responsive to cleaning and would yield a product with satisfactory chemical properties for metallurgical coal. All coals tested from Cambria County yielded strong coke; however, they expand excessively when carbonized singly, and should be used only as minor constituents in metallurgical coking blends when carbonized in slot-type ovens.

Jan 1, 1959

By Robert W. Ageton

The Bureau of Mines investigated the in situ vertical component of the rock stress in the rib of the haulage drift on the 6100-level of the Star mine, Burke, Idaho, using the flatjack and borehole deformation methods. The estimate of the vertical component of stress about 2 feet into the rib at a station along the haulage drift on the 6100-level of the Star mine by the flatjack method is approximately 5,875 psi, whereas the borehole deformation procedure at this station yielded a value of 5,500 psi for the same depth into the rib. The test zone is approximately 5,625 feet below the surface.No attempt was made to extrapolate stress estimates beyond the depth of the flatjack installation.

Jan 1, 1967

By Scott Turner

We are here today to witness the graduation of 63 young men as Engineers in the mineral industries . It is an important occasion and one in which the public takes a keen interest , since this school has long been famous for the educational facilities it affords young men, and for the high professional standing of its graduates . : : : It is fitting that once each year we should pause to review the path the student has traveled , and to reflect upon the perspective opening before him as an engineer . I was invited to come from Washington to take part in this ceremony and to say something to these young graduates . In searching for a theme ," it occurred to me. that perhaps my best contribution would be to duscuss certain beliefs as to college training , deal with the situation in which the young engineer finds himself on graduation , touch on the new ideas of the social and political responsibilities of the engineer , and point out what he may expect to find in practice , and , above all , what he must do to orient himself properly in the mining profession and maintain the best traditions of our brotherhood . Let us first review your college days and see what they have done for you . I am told there are still many temptations in college . I know there used to be . Rest assured the same holds true in the professional life ahead of you. The main difference is , perhaps , that your greatest temptations in college were those offered by your teachers , who tried to entice you into realms of harder work, closer application , increased concentration , clearer thinking and better understanding , by animating your curiosity and increasing your powers of reasoning and of observation . In other words , here you have carefully and systematically been decoyed toward finer and loftier things . Do not expect that similar helpful influences will greet you on every side in your professional life . Often quite the contrary is the case .

Oct 1, 1930

By Donald O. Rausch, Robert H. Merrill, David W. Wisecarver, S. Jackson Hubbard

Results are reported for stress - relief borehole - deformation measurements made in three underground openings near open - pit mines in the Ruth mining district , Nevada . A total of 134 deformation measurements were made in 8 boreholes . These measurements determined the regional stresses in the horizons above , below, and at the elevation of nearby open - pit mine floors ; knowledge of these stress conditions is considered essential information relative to certain aspects in the designing of stable pit slopes . The determinations indicate that the stresses in the district are due to the gravitational load of the overburden in a confined stress field .

Jan 1, 1964

By Thomas M. Barczak

This U.S. Bureau of Mines (USBM) report evaluates the load supporting characteristics of grout columns used as point supports for mine subsidence abatement. The cone-shaped columns were constructed with sodium silicate and cementitious grout in both wet and dry environments. The scope of work included the testing of seven full-scale grout columns in the USBM's Mine Roof Simulator from which the load-deformation and failure characteristics were determined. The performances of grout columns are analyzed with respect to (1) the amount of roof contact established during column construction, (2) shape effects produced by the truncated cone geometry, (3) size effects in reference to grout strength and full-scale column capacity, (4) the effect of wet environments on grout strength, (5) the effect of the sodium silicate on the grout strength and full-scale column behavior, and (6) the stiffness of the grout column. Limited tests were also conducted on cylindrical columns constructed in fabric bags. Recommendations for point support construction using sodium silicate technology and the need for additional research to develop improved containment devices for column construction are addressed in the report.

Jan 1, 2010

By Wm .. O. Vanderburg

This paper describing the mining practices at the Block P mine of the St. Joseph Lead Co. at Hughesville , Mont . , is one of a series of similar papers being prepared by the Bureau of Mines on mining practices , methods , and costs in the various mines of the United States .

Mar 1, 1931

By W. M. Dressel

The objective of the research reported in this publication of the Federal Bureau of Mines was to devise a mineral dressing procedure that would concentrate zinc silicate minerals from certain deposits in southwestern Missouri. The best flotation results were obtained by batch laboratory flotation using sulfidizing agents and ethoxylated cocoamine. The flotation concentrate contained 70 percent of the zinc at a grade of 47.8 percent. Gravity concentration tests showed that 55 percent of the zinc could be recovered at a grade of 48.3 percent.

Jan 1, 1961

By John S. Berber

Olefin and paraffin mixtures (C10-C16 and C10-C22) were separated from low-temperature lignite tar by urea adduction and sulfated to yield secondary alkyl sulfate detergents. The C10 ?C16 secondary alkyl sulfate showed a 99.3 percent biodegradability, and the C10-C22 fraction showed a 96.8 percent biodegradability, exceeding the required standard of 80 percent for the biodegradability of anionic detergents in washing and cleaning compounds. Chlorination of paraffins yielded a detergent of 93.2 to 93.4 percent biodegradability.

Jan 1, 1968

By James Noll

Total carbon (TC) is sometimes used to measure or characterize diesel particulate matter (DPM) in occupational settings such as underground mines. DPM samples are collected on quartz fiber filters. When using quartz fiber ?lters, adsorption of gas phase organic carbon (OC) has been reported, causing a positive bias in the particulate TC results (adsorption artifact). Most of the data on the sampling artifacts and corrections apply to environmental air sampling, where samples are collected at a much higher filter face velocity and the OC concentrations are generally much lower relative to occupational sampling. In this study, we investigated the effects of adsorption artifact on samples from occupational settings. Samples were collected with and without denuders to determine the amount of gas phase OC collected and the accuracy of certain corrections. In underground stone mines, the adsorption artifact was found to positively bias the particulate TC by greater than 20% for filter loadings below 25 µg/cm2 TC (8-h time weighted average) 262 µg/m3). The tandem ?lter correction reduced the effect of the artifact, as high as 60% of the TC value, to less than 11% for laboratory data. It also significantly reduced the effect of the artifact obtained for field samples.

Jan 1, 2008

By T. L. Marchewka

As part of its program to conserve the Nation's natural resources by developing improved performance materials, the Bureau of Mines, U.S. Department of the Interior, in cooperation with the U.S. Department of Energy, has conducted an investigation of materials of construction able to withstand the high temperature and hostile environments encountered in coal gasification units. Refractory pipe liners are required when extremely hot gases or abrasive solids are transported between processing units in the gasification plants. One promising technique for producing refractory pipe (or refractory pipe liners) is centrifugal casting. For this study, the effect of processing variables such as workability, additives, reinforcement and spinning time, and centrifugal force were evaluated using four commercial refractory concretes. In addition, data on characteristics such as strength, density, abrasion, and spalling resistance of 5-inch-diam refractory pipe were developed. Techniques for forming large-diameter (19-inch) refractory pipe also were evaluated. The test results indicated that all four refractory concretes could be made into strong, homogeneous pipe, but that optimum casting parameters had to be determined for each specific composition. The investigation revealed that the major controlling factor in the production of the centrifugally cast pipe was the workability of the refractory concrete.

Jan 1, 1979

By D. E. Wolfson

As part of its overall program of coal-carbonization research, the Bureau of Mines is studying the coking properties of coals from various fields of this country. Few of the coals included in this survey are used for the manufacture of metallurgical coke, although some well-known coking coals necessarily are tested to provide comparative data, particularly on blending properties. The overall objectives of the study were given in detail in a previous report.3/ The inherent suitability of coal for metallurgical purposes, as distinguished from economic considerations, depends primarily on (1) the available reserves, (2) chemical composition, (3) preparation characteristics, and (4) carbonization behavior. These items are considered in selecting coal for carbonization tests.

Jan 1, 1956

By Raymond M. Stateham

The Bureau of Mines evaluated temperature increases on the heads of resin-grouted bolts as indicators of the integrity of the anchoring of the bolt. Expected increases were calculated by the finite difference method; the calculations were checked by bolthead temperature measurements, both in the laboratory and in the field. The accuracy of the calculations varies with the validity of assumptions necessary to the process. Measurements in the laboratory produced a temperature rise of about 4.00 F on the head of a 4-foot bolt when installed with a full column of resin. This increase remained for about 30 minutes. Similar increases were noted on bolts installed at the White Pine mine, White Pine, Mich., but bolthead temperature increases in the mine lasted only about 10 to 15 minutes. When partial columns (reduced amounts) were used, the temperature increases were smaller.

Jan 1, 1976

By Charles Prasky

The Bureau of Mines investigated the conversion of nonmagnetic iron minerals to magnetic form through reduction Toasting operations. The primary objective was to obtain a concentrate that could be used as a direct shipping material for blast furnace consumption. Crude iron materials from the Steep Rock Lakes, Ontario, area were prepared into a blend of 8 parts siliceous ore, 3 parts pyritic ore, and 1 part tailings. Experimental work included laboratory reduction roasting tests, two continuous 10-day campaigns, and one 12-hour test all in a 34-inch by 36¬-foot rotary kiln. The objective of the project was achieved in producing an iron concentrate containing about 66 percent iron with over 90 percent iron recovery. Desirable operating conditions were developed in the kiln but optimum process variables were not completely established.

Jan 1, 1969

This publication summarizes the in-house and contract research projects programmed for fiscal year 1984 by the Bureau of Mines under its Conservation and Development activity. The document provides a mechanism for interested parties to gain insight into projects of the Bureau's Conservation and Development research program. The objective of the Conservation and Development Program is to provide the technological advances needed to stimulate the mining of domestic deposits containing critical, strategic, and other essential minerals in compliance with existing regulations and at costs sufficiently low to be competitive in world markets. Research efforts are directed toward improving the fundamental understanding of processes and procedures involved in the production of minerals. The overall goals will be accomplished by investigating alternative mining methods to increase domestic production of critical and strategic minerals from low-grade deposits; expanding the technology for the economic and efficient extraction of minerals consistent with cost-effective compliance with environmental regulations; and advancing the technologies needed to insure an adequate supply of coal.

Jan 1, 1984

By I. D. Shah

The Bureau of Mines investigated the sequence of principal chemical reactions taking place during the roasting of covellite (CuS). Practically all covellite is converted to digenite (Cul.SS) before oxidation to Cu20 begins. Part of the Cu2O is then converted to CuO, which in turn forms CuS04 through CuO?CuS04 as an intermediary. CuS04 and CuO'CuS04 decompose at 600° to 700° C to yield CuO and S03 (g) as final products. An overall mechanism is proposed for chemical reactions occurring at different interfaces of partially oxidized CuS pellets.

Jan 1, 1970

By J. M. Stuve

Standard heats of formation (AH°p) of YbCl3 (c) and TmCl3 (c) were measured by solution calorimetry. Heat of solution data are given for ytterbium and thulium metals and corresponding anhydrous trichlorides in 4.360 molal hydrochloric acid. The derived standard heats of formation of YbCl3 (c) and TmCl3 (c) were -229,370 ±720 and -235,820 ±400 cal/mole, respectively, at 298.15° K. The resulting heats of formation for YbC13 and TmCl3 are about 1 kcal and 6.3 kcal more negative than previously published values.

Jan 1, 1967

By C. W. Davis

Two general schemes have been used for the determination of gold and silver in material containing considerable quantities of copper ; one is known as the " all fire " method , and the other as the , " combination " , or " wet and dry" method . The all fire crucible method , using an excess charge of litharge , has been found satisfactory when the copper content of an ore is under 6 per cent , ( Loevy , J. , Zur Edelmetallbestimmung in hochprozentigen Kupfererzen : Chem. Ztg . Jarhrg . 35 , 1911 , p . 278 ) , or where the precious metal value is so great that a small sample can be used . In the latter case , silica is added until the copper ratio is sufficiently low . If there is more than 6 per cent of copper in an ore , the lead button obtained from a crucible fusion will require repeated scorification before . it can be cupelled successfully . Rescorification is not only tedious , but also causes a slag loss of precious metals . In combination methods , the copper is dissolved , and the gold and silver in the residue . is determined by fire assay Although some combination methods have given satisfactory results for gold and silver , they are not applicable when an estimation of the platinum metals is required . Since substances containing platinum are frequently high in copper , a study of methods which might be used for the estimation of small quantities of gold , silver , and the platinum metals in such material was considered worth while . The estimation of platinum in ores by fire assay methods has been described in Technical Paper 270 of the bureau; ( Davis , C.W. , The detection and estimation of platinum in ores : U. S. Bureau of Mines Tech . Paper 270 , 1921. ) the present paper , which is supplementary to that report , deals chiefly with the application of combination methods , taking them up to the point where the fire assay is to be applied .

Mar 1, 1921

By Wing G. Agnew

[This report presents the results of tests made by the Mining Division, Bureau of Mines, on the relative durability of manganese-steel drill rods and carbon-steel drill rods for use with the detachable bolts]

Jan 1, 1941

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations No. 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251, of which this is the fifth. The data are accompanied by maps showing the location of holes drilled and deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in Volume I. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each half township is given with the discussion of that area.

Jan 1, 1948