Search Documents

By A. D. Marcy

The Midnite Mine is an inactive, hard-rock uranium mine in Stevens County, WA. Oxidation of sulfide-containing minerals, primarily pyrite, in the ore body produces large quantities of acidic water. An interception system installed by the mining company limits the discharge of contaminated water from the mine. The U.S. Bureau of Indian Affairs (BIA) and the U.S. Bureau of Land Management (BLM) have been actively involved in planning remediation of the disturbed areas. To assist in remediation, the U.S. Bureau of Mines (USBM) initiated research to determine water quality and to define ground water flow characteristics. USBM personnel designed a monitoring network, supervised installation of sampling wells, and collected and analyzed water samples. This Report of Investigations describes interpretation of data collected between December 1989 and April 1992. The computer program WATEQ4F was used to identify aqueous species distribution and to calculate potential solid phase controls of solubility. To assist in interpretation of changes in water quality between sampling locations and to develop models describing proposed flow paths, the computer program BALANCE was used. Using output from these programs and field observations, a description of the chemistry along proposed ground water flow paths at the mine is presented.

Jan 1, 2010

By X. Shi, K. S. Kaspnak

"The generation of free radicals from reactions of nickel (Il)-thiol complexes with molecular oxygen and model lipid hydroperoxides was investigated by electron spin resonance (ESR) utilizing 5,5-dimethyl-1-pyrroline-N-oxide (DMPO) as a spin trap. Incubation of nickel (II) [Ni(II)) with cysteine in an aerobic environment generated hydroxyl (·OH) radical, which then reacted with cysteine to generate a carbon-centered alkyl ( · R) radical. Radical generation was inhibited under a nitrogen atmosphere. Model lipid hydroperoxides, cumene hydroperoxide, and I-butyl hydroperoxide enhanced the yield of these radicals and also generated an alkoxyl (·OR) radical. Radical yield decreased by approximately half under a nitrogen atmosphere. Although histidine did not cause radical formation in the reaction between Ni(II) and cumene hydroperoxide under aerobic conditions, the addition of histidine to a mixture containing Ni(ll), cysteine, and cumene hydroperoxide under the same experimental conditions increased the yield of · R radical but lowered the yield of ·OR and ·OH radical adducts. It thus appears that histidine caused the ·OH attack to be more site-specific. Similar results were obtained utilizing 1-butyl hydroperoxide. Penicillamine or N-acetylcysteine yielded similar results except that under aerobic conditions, reaction between Ni(ll) and N-acetylcysteine without hydroperoxide did not generate a significant concentration of free radicals. Under the same experimental conditions, cystine did not generate any detectable free radicals, suggesting an important role of the -SH group in Ni(II)-mediated free radical generation. The results indicate that free radical generation from the reaction of Ni(Il)-thiol complexes and molecular oxygen, and/or lipid hydroperoxides, may play an important role in the mechanism(s) of Ni(II) toxicity and carcinogenesis. INTRODUCTIONWhile nickel is a well-recognized carcinogen [l, 2]. the underlying biochemical mechanisms remain unclear (3, 4). Recent studies suggest that these mechanisms may involve oxidative DNA damage through free radicals, especially the hydroxyl (•OH) radical [5-13]. The mechanisms of nickel carcinogenicity and toxicity may also involve lipid peroxidation [14-21]. Unlike ferrous ion [Fe(II)], the Ni(II) cation itself does not directly react with 02, H2O2, or lipid hydroperoxides to generate free radicals [12, 21]. However, it has been reported that Ni(II) complexes with certain synthetic oligopeptides, e.g., tetraglycine or glycylglycylhistidine, make Ni(II) reactive with 02. This reaction results in transitory formation of Ni(III) and degradation of the organic ligand via free radical reactions [22]. Such Ni(II)-peptide complexes are also capable of reacting with H2O2 to produce oxygen free radicals [11, 12]. Although the cellular environ¬ment may not contain these particular peptide ligands that are known to render Ni(II) redox active in vitro, it does contain a variety of oligopeptides that are capable of forming Ni(II) complexes at physiological pH, and thus may facilitate Ni(II) redox activity in vivo. These oligopeptides include glutathione (y-L glutamylycysteinylglycine), carnosine (homocarnosine (y aminobutyryl-L-histidine), and anserine ( B-alany1-3-methyl-L-histidine)."

Nov 1, 1995

By R. N. Love, L. Goldman

"INTRODUCTION When tannin is present in a boiler water, it causes certain difficulties in many analytical testing procedures because of its colloidal action in interfering with the removal of suspended matter by filtration and also because of the color it imparts to the boiler water.For example, in any test for phosphate in boiler water the first step is to filter out of the sample all sludge and suspended solids. Calcium phosphate in the sludge would give high results if not completely removed. If tannin is present in the sample, the sludge and suspended matter tend to pass through the filter paper so that it is difficult to remove it all. It may even be that tannin makes some of the suspended material in the sample completely nonfilterable. If this is true, it would be necessary to destroy or remove the tannin from the sample before filtering to get complete removal of calcium phosphate from the sample. In addition, if the test used is a colorimetric one, the tannin causes interference by its own color.As the calorimetric phosphate test is so convenient for control purposes and the use of tannin for boiler water treatment has become common, it has become necessary to develop suitable methods for employing the colorimetric phosphate test for boiler waters containing tannin. In this paper three different methods for doing this arc described and studied."

Oct 1, 1946

By Frank E. Cash

Data on the occident experience of the pebble-phosphate industry in Florida for 1937 and 1938 are combined in this report with statistics for the 7-year period 1930-36, inclusive, which were published in Information Circulars 69174/ and 69685/. The periodic publication of such data enables the pebble-phosphate industry, as well as other industries, to consider relative hazards, compare experience, and thereby help to prevent accidents. ACKNOWLEDGMENTS Accident data ere furnished by the following; operating companies: Amalgamated Phosphate Co., Brewster; American Agricultural Chemical Co., Pierce; Coronet Phosphate Co., Plant City; International Agricultural Corporation, Mulberry; Phosphate Mining Co., Nichols; Southern Phosphate Corporation, Bartow; and Swift & Co. Fertilizer Works, Bartow.

Jan 1, 1940

By J. R. Thoenen

During the year 1927 the Bureau of Mines, at the request of a number of quarry operators, undertook to make a study of quarry operating costs in order to determine average costs for certain operating conditions and to suggest a model cost accounting system for quarry operations. A detailed questionnaire was prepared and mailed by the bureau to all quarries on its records as employing ten or more men in 1926.

Jan 1, 1929

By H. C. Miller

The removal of the mud sheaths that are deposited against the faces of productive oil sands during rotary drilling is one of the important problems confronting operators, especially in semidepleted fields where formation pressures are low. Unless the mud sheaths behind the perforated oil strings and liners are removed and the sands exposed, oil cannot enter the wells. Consequently much oil that otherwise might be produced from low-pressure sands is trapped and never recovered. Various types of perforation washers, down swabs, and agitators are used at present for breaking down the mud sheaths and removing the disintegrated clay particles from wells after the perforated Wipes have been inserted. Mechanical methods for removing mud sheaths are :quite satisfactory, but prompted by the request of certain .operators in the California oil fields Bureau of Mines engineers have conducted a series of laboratory tests with the view of developing a chemical method for removing mud sheaths in oil wells that will be applicable to field conditions. This report describes the laboratory work and deals generally with a chemical method for removing the mud sheath, cake, or plaster deposited against the face of oil sands in drilling wells end in wells that, on being shut in temporarily during periods of overproduction of oil, are conditioned for the shutdown .period by filling the well opposite the producing formations with mud fluid. The method described in this report was devised in the San Francisco laboratory of the Bureau of Mines and, as far as the writers have been able to determine, differs from any chemical method ever used in actual wells. The method proposes to add a small amount of calcium carbonate (preferably pulverized limestone) to the mud fluids before they are introduced into the wells so that the resultant mud sheaths will be susceptible to disintegration by acid solutions when it is desired to expose the faces of the oil sands in the wells.

Jan 1, 1934

By M. E. Volin

The tungsten potentialities of the Combination mine were examined by a mining engineer of the Bureau of Mines in 1947. A report based upon his personal knowledge of the mine and the results of the examination contained recommendations for further investigation. This report presents factual data from Bureau of Mines field investigations begun in August 1947 and continued until December 1948, except for a 5-month recess during the first winter. The Combinat.ion mining property of 52 patented claims and 15 patented mill sites is in the Black Pine mining district, Granite County, Mont., 11 miles northwest of Philipsburg. The altitude in the mine vicinity is approximately 6,500 feet.

Jan 1, 1952

By W. A. Stickney

This report summarizes the results of laboratory tests of five samples of low-grade phosphate ores from Idaho. The laboratory test work has demonstrated that by grinding, desliming, and flotation a portion of the siliceous gangue can be removed. The highly carbonaceous ores responded successfully to treatment after preroasting, to produce a plus-30-percent-P205 product. It has been found that highly siliceous ores, as represented by the samples treated, are more readily amenable to concentration than ores high in calcium carbonate. Of the five samples tested, four were amenable to concentration to a product containing over 30 percent P205. One sample, from the Conda, second bed, was not amenable to mineral-dressing treatment to produce a plus-25-percent-P205 product.

Jan 1, 1955

By H. C. Miller

The removal of the mud sheaths that are deposited against the faces of productive oil sands during rotary drilling is one of the important problems confronting operators, especially in semidepleted fields where formation pressures are low. Unless the mud sheaths behind the perforated oil strings and, liners are removed and the sands exposed, oil cannot enter the wells. Consequently much oil that otherwise eight be produced from low-pressure sands is trapped and never recovered. Various types of perforation washers, down swabs, and agitators are used at present for breaking down the mud sheaths and. removing the disintegrated clay particles from wells after the perforated pipes have been inserted. Mechanical methods for removing mud sheaths are quite satisfactory, but prompted by tie request of certain operators in the California oil fields Bureau of Mines engineers have conducted a series of laboratory tests with the view of developing a chemical method for removing mud sheaths in oil wells that will be applicable to field conditions.

Jan 1, 1934

By L. Kaufman

Fifteen boride composites were synthesized by hot pressing and evaluated by physical and incendivity testing as non-sparking tool materials. The incendivity tests, conducted at the U. S. Bureau of Mines, Albany Research Center, compared the boride compo-sites with standard cobalt-bonded tungsten carbide material used for coal cutter bits. Two titanium diboride composites and two zirconium diboride composites out-performed cobalt-bonded tungsten carbide in wear resistance and reduced tendency to cause ignitions. However, three of these candidates exhibited undesirable chipping. The remaining candidate, a TiB2-(Ni, Cu) composite, did not chip, nor did it cause ignitions at levels where cobalt-bonded tungsten carbide tools caused ignitions in the incendivity tests. Thus, this material appears to be a logical candidate for further development.

Jan 1, 1973

By John E. Pahlman

The U.S. Bureau of Mines has continued its investigation of chemical additive drilling fluids that produce a zero surface charge (ZSC) on a rock to better define the boundary conditions of the phenomenon. Laboratory drilling tests were performed on Minnesota taconite, Tennessee marble, and Sioux Quartzite using diamond-impregnated coring bits or tungsten carbide spade bits. Drilling fluids were made from chemical additives such as inorganic salts, cationic surfactants, cationic polymers, acids, or nonionic polymers in either distilled, deionized water (DDIW), mine pond water, mine well water, or tap water. These additives were tested below, at, and above their respective ZSC concentrations. Penetration and bit life improvements obtained with ZSC concentration solutions ranged from 88 and 56 pct, respectively, to over 650 pct and over 400 pct, respectively, for the additives tested. Polyethylene oxide (PEO) was found to be the best additive for ZSC-controlled drilling because a continuous range of PEO solution concentrations produced the enhanced ZSC-controlled drilling performance.

Jan 1, 1989

By George T. Krempasky

This report is one of a series of Bureau of Mines Information Circulars dealing with mining methods and costs throughout the United States. It describes drifting, crosscutting, and raising operations at several mines in the Coeur d'Alene mining district, Shoshone County, Idaho. Ore bodies in the Coeur d'Alene district are generally in steeply dipping tabular ore zones, are irregular in shape, erratic in occurrence, and have been extensively mined along the strike and down dip. Because of the extended attitude of the deposits a great deal of development work is required. Drifting, crosscutting, and raising methods are described in this report. Shaft sinking is the subject of another report in the same series.

Jan 1, 1960

By Larry A. Haas

The Bureau of Mines is investigating the use of complex gas mixtures, such as would be produced by coal gasification, for reducing iron oxide pellets. A semiempirical model was developed to predict a priori the reduction rate of an iron oxide pellet in a laboratory tube furnace with simulated coal gases at a total pressure of 1 atm. The model uses partial pressures of H2, CO, CO2, CH4 (methane), water vapor, and a temperature-dependent term to predict the rate of reaction. The reduction rate (weight loss per unit of time) was determined with a thermo-gravimetric apparatus (TGA) in the temperature range of 800° to 1,100° C. The ranking of the reductants, in order of decreasing reducing potential, is H2, CO, and CH4 at temperatures between 800° and 1,000° C; however, CH4 became a better reductant than CO at 1,100° C. Water vapor did not decrease the reduction rate as much as did CO2, Carbon deposition was observed at temperatures below 1,000° C with gas mixtures with high CO and low H2 concentrations. With low-Btu gas at 900° C, over 90 pct of the iron oxide was reduced to iron in less than 3 h. This com-pares with a reduction time of 1.5 h with medium-Btu gas and 1 h with reformed natural gases.

Jan 1, 1985

By David T. Couillard

Task training is increasingly important in mining operations because of the ever-accelerating pace of technological innovations and the concomitant increasing complexity of mining equipment. This Bureau of Mines report describes two successful task training program In use in two open-pit taconite operations in northeastern Minnesota. The programs are different in approach, but both have improved safety and in- creased productivity while lowering costs. Methods of training both before and after passage of the 1977 Mine Safety and Health Act are described, and the impact of this act on task training at each operation is discussed. The report identifies four common principles that have contributed to the success of the two training programs and presents plans each operation has for improving future training through new technology.

Jan 1, 1984

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations No. 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251, of which this is the seventeenth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project, except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes.

Jan 1, 1948

By J. J. Demeter

As part of its work on converting coal to fluid fuels, the Federal Bureau of Mines has been studying the synthesis of liquid fuels from carbon monoxide and hydrogen by Fischer-Tropsch synthesis. A fluidized bed of nitrided, fused-iron catalyst has been operated successfully to produce high yields of oxygenated compounds. Trouble-free operation continued for over 800 hours, and the test was terminated voluntarily. About 85 percent of the fresh feed was converted when the unit was operated at a space velocity of 500 hr.-1, a 12:1 recycle-to-fresh-feed-gas ratio, a 300-p. s. i. g. pressure, and a temperature of 252° C. When operating at a fresh-feed-gas space velocity of 1,000 hr.-l and a 9:1 ratio of recycle to fresh gas, conversion of fresh feed was 68 percent, and the product yield was 235.9 grams per cubic meter of synthesis gas converted. The oxygenate and C5 and heavier hydrocarbon yield was 110.6 grams per cubic meter of gas converted, 83 percent of this was oxygenates. The atom ratio of N:Fe of the catalyst, initially 0.455, decreased to 0.288 by the end of the 800-hour experiment. Nevertheless, the yield of oxygenated compounds per cubic meter of H2 + CO converted at the end of the run was approximately the same as that obtained 500 hours earlier with identical operating conditions. X-ray analysis of the discharged catalyst indicated that only ?-iron carbonitride was present. Sieve analysis of the discharged catalyst indicated that only 2 percent of fines was produced during the reduction, nitriding, and synthesis.

Jan 1, 1959

By R. W. Lewis

Spectrochemical procedures were developed using dc arc excitation for the determination, in parts per million, of 18 impurity elements in electrorefined beryllium and high-purity beryllium oxide. The metal samples were dissolved in dilute hydrochloric acid, evaporated to dryness, and converted to the oxide in a muffle furnace at 900° C. Germanium oxide was added as an internal standard for the determination of 15 of the elements, copper oxide for boron and molybdenum, and neodymium oxide for calcium. The average coefficient of variation was 11 percent with the exception of copper, which averaged about 43 percent.

Jan 1, 1962

By Stephen A. Swan

Bureau of Mines research has not included analyses of mining dredge safety since 1948. Because of the increasing use of dredges, 63 fatal accidents and several hundred nonfatal injury accidents involving dredges were examined. Also, 31 working dredges and 3 dredge manufacturers were visited to acquire qualitative information. Drowning accidents represented 59 pct of the fatalities and are delineated in detail. Also, countermeasures against other hazards are discussed.

Jan 1, 1985

By Chase E. Sutton

The porosity of a sand is usually the measure of its capacity for holding fluid, although porosity is sometimes selective; that is, a small percentage of the actual pore space (voids), particularly in fine-grained sandstones, may be isolated by the cementing material which prevents the entrance of fluids under normal conditions. Obviously, however, porosity determinations are essential to an engineering study of underground conditions of an oil field, and a simple and reliable method of obtaining a reasonably accurate figure for average porosity is desirable. This report describes a method suggested by Ruasell,3 which was used by the writer in the preparation of a report on the Texhoma-Gose pool, Archer County, Tex.4 The conditions in this pool were particularly favorable for obtaining an average porosity figure, in that some 30 to 35 core samples of the pay sand were available for analysis.

Jan 1, 1928

By L. G. Marshall

This report is one of a series published by the Federal Bureau of Mines describing mining methods and performance at individual operations throughout the United States. The objective of these papers is to promote development and conservation of our mineral resources by disseminating reliable technological information on mining methods, practices, and results that may be applied to the engineering analysis and solution of mining problems. SUMMARY Operation of a limestone quarry producing flux for the steel industry and crushed stone for production of concrete is described in this report. The deposit being mined is a flat-lying limestone formation under a thin overburden 2 to 25 feet thick. The height of the quarry face varies from 9 to 60 feet, averaging 40 feet. Production rate ranges from 4.5 to 5 million long tons per year.

Jan 1, 1959