Search Documents

By R. G. Dressler

The design and operation of the Koppers powdered-coal gasifier and its auxiliaries at Louisiana, Mo., are described. This unit was designed to convert 1 ton of coal per hour with oxygen and superheated steam into synthesis gas - primarily carbon monoxide and hydrogen. The first run was made on May 4, 1949. After this, 44 short runs (less than 8 hours each) and 1 long run (lasting 11 days) were made. Total gasification time was 420 hours. The gasifier was not cooled down during the year when these runs were made. After an initial period of test operations and equipment proving, during which 12 runs were made, the effect of numerous variables on gasifier performance was studied. The long run was made primarily to check the equipment in sustained operation. Detailed data from these runs are presented.

Jan 1, 1954

By Alan A. Bergeron, J. L. Michels, R. L. Collins

Advanced communication and monitoring systems were developed and demonstrated in three underground mines representing different mining techniques, geographical areas, and material mined. The first mine was a large coal mine in western Pennsylvania that used room and pillar techniques and continuous mining methods. The system developed for this mine provided private telephone channels, environmental monitoring, and control of underground equipment, all on a single coaxial cable, with all system operations under the direction of a minicomputer. Many advanced features were incorporated into the system, such as paging of roving personnel, two-way section wireless, through-the-earth emergency communication, and redundant signal paths. Television was multiplexed into the system for underground equipment surveillance. A hoist radio system completed the complement of equipment at the mine. The second mine was a magnetite ore mine in eastern Pennsylvania that used block caving mining techniques. A radio system was developed that provided two-way communications between trackless vehicles and roving personnel. A unique system of uhf/vhf repeaters combined with a flleaky-feeder" transmission line offered operational and emergency features not previously found in mine communication systems. Evacuation alarming, personnel paging, fan-hole drill operator communications, and maintenance and safety vehicle dispatch were provided. The system required no dispatcher and operated during power failure. A hoist communications/shaft inspection system completed the installation. The third mine was a deep silver mine in the Cour d’Alene district of Idaho. The system developed for this mine utilizes a single wire pair to provide up to 14 voice channels. A unique combination of PBX, telephone carrier system, and intercoms offered private conversations, selective signaling, and emergency backup communications. Two hoist communication systems were installed to provide a voice link and in-cage belling signal between hoistman and cage.

Jan 11, 1981

By C. E. Wyndham

The occurrences of manganese In Alabama were reported to be widely scattered over the northeastern section of the State, and these were examined before a development project was started.2/ The most promising and available showings were chosen for further investigation, which include 1 deposit in Goshen Valley, 6 in the Rock Run area, and 2 in the northern section of Calhoun County. The work was performed by the Bureau of Mines from July 29, 1949, to February 17, 1950. The work consisted of power auger drilling 69 holes 3-1/2 inches in diameter and totaling 2,548.4 linear feet. The accuracy of samples from auger drill holes in this type of deposit was determined by sinking two shafts a total depth of 68.17 feet, from which channel samples were cut. Sixteen rotary core holes totaling 1,048.7 linear feet were drilled with a 3-inch, double-tube core barrel. Twenty-two diamond core holes were drilled with a 2-1/8-inch, double-tube core barrel and NX diamond bit. In addition to the above drilling 220.8 cubic yards of soil and rock was excavated by hand from 403.9 linear feet of trenches and 69.7 feet of test pita. A total of 206 samples were taken and analyzed for manganese, iron, cobalt, nickel, and insoluble.

Jan 1, 1953

By C. H. Fisher

[Many methods of analyzing tar oils for their tar acid and base content have bun employed in connection with both academic and. industrial investigations. Most of these analytical procedures are based on the diminution in volume caused by extraction with alkali and mineral acids (contraction method), although other methods haves been employed.4/ In many instances the adoption of an analytical method was not preceded by adequate study, and, as a consequence, the literature, on this subject is conspicuous for its contradictory claims and recommendations. It has bin shown in the, case of certain synthetic solutions5/ that large errors may result if the analysis is carried out by simple extraction with alkali and mineral acids.]

Jan 1, 1936

By Geoffrey C. Huggins

Diagnostic: tests were performed on a production ST-5A Load-Haul-Dump machine manufactured by Wagner Mining Machinery Company to evaluate and rank order noise sources. The diagnostic evaluation indicated that the major noise sources were the transmission, the engine, and the cooling fan. This phase was followed by implementation of recommended noise control treatments, which included vibration isolation of the transmission, a transmission enclosure, an engine enclosure, and modifications of the inlet to the cooling fan. The final step in the program was an underground operational period which began on 31 August 1976 at the National Gypsum Mine in Shoals, Indiana. The noise control treatments successfully reduced the LHD operator noise exposure by 7 dB(A), thus increasing its allowable operation time by a factor of 2.7. Actual measurements made underground using noise dosimeters have indicated that, during, a typical shift, the noise control treatments have reduced the fractional exposure to an allowable level. The report discusses the mechanical aspects of the LHD, its noise sources, the treatments applied, the final levels achieved, and field experience with the noise-controlled machine.

Jan 1, 1977

By K. K. Kelly

METALLURGICAL thermochemistry of titanium is a broad subject and (if data were available) could include a wide variety of topics. The present report is restricted to extractive metallurgy and to substances and reactions that bear upon the magnesium, sodium, and hydrogen-reduction processes employing titanium tetrachloride. The aim has been to present enough data so that the reader not only can check: the calculations for the reactions discussed but also can conduct related calculations if he so desires, without recourse to other compilations of data. The subject matter divides naturally into two parts-the selection of the data to be adopted and the application of these data to pertinent metallurgical reactions.

Jan 1, 1959

By C. H. Fisher

[Mxny methnhs of ,analyzing tpr oils fnr thoir tar acid ~nd base cnntent hava boon employL~d in connection mith both ac~d,.mic and. industrial investigs- tions. Mnst of thznu nnalyticel proc?durn~s aro bpsed nn th; diminution in volums caused by extract lon sit5 alkali 5 minL+ra,l acids (cantrsction rn,>thod) , although othrr mr~thrids havu &apos;sL<on ?q~lnglt 8 . In many instmccs th-: donti ti on of RT~ m~lytic~l m ithod was not ;r.:c ~d~d by ~d.jqunt9 study, and, ns 3 cone+ qucnce, tha lit .,ratur ? on thls sub,jr:.ct is consoScuous for its cnntr~dictnry . claims and rocnmmondatinna.. 1.t tiR.s b9~n shoyn in th;, cnsn of c.lrtn.in synth?tic solut innsfi/ thnt larg~ jr-orn sny rcsult if th2 ,mnlysis is c~rri~d out by sim~la extraction wi.th alidi r.nd min 3rd ncids.]

Jan 1, 1937

By ALBERT LONG, Wing G. Agnew, FELIX CHAYES, Alton Gabriel, Leonard Obert

Although the technique of diamond drilling was developed nearly 80 years ago, the use of this process as an aid to mining and other fields of engineering has increased greatly during the last decade , primarily as a result of the development of the cast -set bit , which now largely replaces the hand - set types , and of the use of bort instead of carbons . Since this transition to cast - set bits and bort diamond , many papers ( 1-14 ) have been written on the application of diamond drilling to various engineering problems . These papers contain , besides specification of the problems , some information on the labor and bit costs and a few data on drilling technique . These data , however , are subject to restricted interpretation owing to the large number of variables , which are not controlled in field drilling . Only one paper has come to the attention of the authors , namely , that by Sundberg and Lindqvist ( 16) , which reported a study of diamond drilling under controlled conditions . This paper was written early in the transition period, and the data and conclusions presented therein have had , without a doubt, considerable influence on the development of presentday diamond bits and In view of the fact that during the last 10 years thrilling procedure . have been new developments in diamond bits. and new applications of diamond drilling , a general program of research has been inaugurated to study the problems resulting from these changes .

Mar 1, 1947

By E. H. Denny

This paper discusses accident experience and costs in 150 Colorado coal mines for the 5 years 1929-33; these mines produced 62 percent of Colorado&apos;s coal tonnage during this period. This and similar studies by the United states Bureau of Mines in other States (listed in the appendix to this report) make available comparable information on mine-accident costs and bring out clearly the importance of accident reduction from the humanitarian as well as from the economic standpoint. Compensation insurance costs constitute a considerable part of the cost of coal output. The tendency toward greater liberalization of workmen&apos;s compensation laws and increased benefits thereunder may mitigate to some extent the seriousness of an accident to a worker and his dependents, but no compensation is paid ultimately, not by an insurance fund but by the mine operator and the general public, which includes the miner. The one really effective method of reducing compensation costs is to reduce the number and severity of accidents.

Jan 1, 1935

By M. W. Von Bernewitz

Corduroy is used for saving gold in small Land large milling plants throughout the world. Investigations by the Metallurgical Division of the Bureau of Mine indicate that corduroy blankets, used with or without a trap or jig in the mill classifier circuit, often are effective in concentrating gold and sulfides, especially if the gold does not amalgamate readily and if not enough sulfides are present to warrant the use of a shaking table, flotation cells, or cyanide plant. Most cold-mining countries include several or many small miner, that produce siliceous ores low in sulfides and gold, which can easily be amalgamated or caught in traps or jigs or on corduroy and shaking tables. At these mines the ore is crushed by stamps or bill mills, and the flow sheets include plates, flotation cells, and cyanide treatment, yet probably nearly as much of the pair minerals may be recovered by the less expensive plant. A well-known western maker of mine and mill equipment asserts, as the result of considerable observation of installed plants, that old and other valuable minerals should be caught as soon as they have been released by a mill, end recommends jigs to do this. A supplier of corduroy has informed us that at some mines this material is being replaced by jigs that catch gold as fine as 400-mesh. But for the small operator, inexpensive equipment such as a corduroy table may be better adapted and give a good recovery of gold and associated minerals.

Jan 1, 1939

By E. A. Sondreal

The Bureau of Mines investigated the use of lignite char for producing carbon disulfide; CS2 production rates were as high as when wood charcoal was used as raw material. The maximum space velocity for CS2 produced in the bench-scale study was 9,280 hour-1, reacting sulfur and lignite char at 792° C. The reaction temperature and the temperature at which the char was carbonized were the two most important factors in determining CS2 production rates. Increasing the carbonization temperature in nitrogen from 400° to 900° C advanced the temperature at which carbon disulfide was first produced from 550° to 850° C. The average activation energy for reacting chars with sulfur was 44,000 cal/g mole. The reaction was first order with respect to the partial pressure of sulfur. Increasing the rate of sulfur admission caused a decrease in rate of production at otherwise similar conditions. Rates were not affected by either char size or sodium carbonate catalysis. High space velocities at moderate temperatures using inexpensive lignite chars could offer an economic advantage in the manufacture of carbon disulfide provided that yields were attractive.

Jan 1, 1967

By G. W. Grove, H. R. Burdelsky, F. E. Griffith

"INTRODUCTION The work of using a system of air locks in unsealing a mine in Ohio following a fire probably was one of the outstanding jobs of its kind in a medium-thick coal bed.The fire in this mine, thought to have been of electrical origin, was discovered at about 1:30 a.m. on December 11, 1941. Forty-four men were working in the affected section at the time; 5 escaped unassisted, and 37, who had barricaded themselves, were rescued. The bodies of two men, who had succumbed after breathing fumes given off by the fire, were brought part way out of the mine before it became necessary to seal the mine.Direct attempts to extinguish the fire with water were abandoned when hazardous amounts of 'carbon monoxide, methane, and other inflammable gases were detected in return air passing through the main haulageway and escape-way of the mine.The mine was completely sealed on the surface at about 8 p.m. on December 12, 1941, with the two bodies remaining in the mine. Sixteen days after the mine had been sealed, the two bodies were recovered. This was accomplished by air-locking through a partitioned-off stairs compartment of a ventilation shaft. This work was done under adverse barometric and atmospheric conditions.A method for collecting representative air samples from the immediate fire area was used successfully by utilizing a vacuum pump on about 10,000 feet of existing water line that had been broken near the fire area.The immediate fire region was sealed, and confined to a relatively small area; the remainder of the mine was recovered, and operations were resumed February 9, 1942, or 59, days from the time of sealing the mine on the surface. This recovery was made by air-locking the main entries inby from the shaft and No. 2 right-face entries.The distance between air locks averaged about 500 feet, and as each new set of seal stoppings and air locks was completed, the old or outby seals were taken out and the area between was ventilated. In ventilating this area, it was often necessary to use line curtains to direct the air into dead-end places."

Oct 1, 1947

By Gary E. Sherman

To aid the U.S. Army Corps of Engineers In their Resource Development Navigation Study, the U.S. Bureau of Mines (Bureau) examined the potential for mineral development near ten Alaska port sites. This report presents the results for the first three sites: Bethel, Kivalina (Red Dog), and Omalik Lagoon. The mineral deposits near Bethel are primarily gold and mercury; the nearest deposit being 55 mites away. Because of the expense of constructing and maintaining a road over the poorly drained lowlands, the potential of Bethel as a port site in the near-term is considered to be low. The Kivalina site currently serves the Red Dog mine and has the potential to handle material for similar deposits in the area. Results from a lead-zinc mine model indicate that potential for additional mine development exists in the area. Coal is the major deposit type found near the Omalik Lagoon site. Due to environmental constraints, development of a large-scale mine producing coal for export is considered unlikely. A small-scale coal mine model was used to examine the feasibility of producing coal for regional use. This alternative may be feasible but would require conversion of heating/generating equipment in the area.

Jan 1, 2011

By W. H. Emens

[This circular is one of a series dealing with tie development and equip¬ment of small and medium size mines, and with the costs of such work prior to productive operation. The preparation and publication of these papers by the Bureau off Mines has been made possible through the cooperation of various min¬ing and development companies. The bureau of Mines has published a series of circulars dealing with min¬ing methods and costs at a large number of producing nines in the United States, Canada, Mexico, an, other countries. Unit costs of development work, shaft sinking, (rifting, crosscutting, tunneling, and raising are usually much higher in the preliminary development of a property than during its productive life.]

Jan 1, 1933

By Arno C. Fieldner

The objectives of the coal-research activities of the Bureau of Mines are very well expressed in the organic act of Congress establishing the Bureau. It reads as follows: That it shall be the province and duty of the Bureau of Mines, subject to the approval of the Secretary of the Interior, to conduct inquiries and scientific and technologic investigations concerning mining, and the preparation, treatment and utilization of mineral substances with a view to improving health conditions, and increasing safety, efficiency, economic development, and conserving resources, through the prevention of waste in the mining, quarrying, metallurgical and other mineral industries; to investigate explosives and peat; and on behalf of the Government to investigate the mineral fuels and unfinished mineral products belonging to, or for the use of, the United States, with a view to their more efficient mining, preparation, treatment, and use; and to disseminate information concerning these subjects in such a manner as will best carry out the purposes of this act.

Jan 1, 1946

By R. L. Grayson

"Compliance standards for respirable dust, which are reduced because of high quart: concentrations, have become an industry-wide problem. Research on the physical and chemical character of quart-classified particles in respirable coal mine dusts indicates that they may exist in intermixed layers or may be coated by clay or coal material. The relative amount of intermixing varies with the coal seam being mined. If most of the quart: particles of a mine dust are ""pure,"" then the dust may have a high fibrogenic risk potential because of truly free silica and the compliance standard should be lowered. lf, however, quart: is locked inside another material matrix, or coated, a reduced compliance standard may not be appropriate.Although much research has been done on coal workers' pneumoconiosis (CWP) over the past decades, the etiologic agents of the disease still have not been pinpointed. The predominant methods of characterizing respirable coal mine dusts were bulk analysis techniques for determination of elemental and mineralogical concentrations, the results of which were used in statistical analyses to determine relationships between dust composition and the occurrence of CWP. These methods are incapable of finding the etiologic agents in the dust primarily because of complicated and confounding physiochemical factors, which may be discovered if the focus of characterization was done on a dust particle level.The SEM/EDXA-based research discussed here shows a significant difference in the number of ""pure"" quartz particles in respirable dusts collected from different mines. Some of the results have been reported previously (Grayson, Andre, and Simonyi, 1988). Concurrent research by other investigators (Wallace et al., 1989) demonstrates an SEM/EDXA-based methodology to pinpoint the location of the ""contaminating"" substance(s ) in a quartz-classified particle. The research of the European Economic Community has also begun analyses on the respirable-dust-particle level (Robock and Bauer, 1988).Since the compensatory and intangible costs of CWP are substantial in the United States, it is important that the etiologic agents be determined and then either controlled or neutralized in a cost-effective way. This line of research is especially important consid-ering the forecasted. near-term growth of coal production and the evolution of high productivity longwall panels (an immediate problem in compliance) and continuous mining sections ( a probable future problem).This need has been accentuated now that nearly all respirable dust samples submitted to MSHA are analyzed for free silica (Tomb, Parobeck, and Gem, 1986). Today a real problem exists in the coal industry, both underground and surface, because of high quartz levels in respirable dusts causing substantially reduced compliance standards (Murphy, 1989).The combined results of the respirable dust particle investigators indicate that conventional bulk sample analyses may not faithfully represent the amount of biologically available or active quartz in all mines with a high level (greater than 5% ) of quartz in the dust For example, some mine dusts might contain predominantly occluded (or coated) quartz particles where bulk analysis would result in anomalously high ""free silica"" measurements. The same result would occur when quartz particles are intermixed substantially with other minerals that can alter the surface of the composite particle away from a quartz-behaving character."

Mar 1, 1992

By Leo J. Neill, O&apos

Abrasives are essential to the manufacture of munitions - airplanes, gas, shells, tanks, and in fact every product that involves metal forming or finishing. An indication of the importance of abrasives in the national defense and aid-to-Britain programs is the close peace-time correlation between demand for abrasives and automobile production, which in recent years has consumed more than 35 percent of the total output of abrasives. Unprecedented demands on the abrasives industry are forecast by the rapid expansion in airplane output, tie increased mechanization of all armed forces, and the consequent speeding up not only of the factories where finished munitions are made but also of the steel mills and other factories were additional large quantities of abrasives are needed for snagging or rough-grinding semifinished products before they can be used by the fabricators. A recent survey by the artificial abrasives manufacturers indicates that they can readily increase their output 75 percent compared with the previous peak of 1937 without building new plants. By overhauling production schedules, their maximum production possible could be increased to 182 percent of the 1937 output, and the nature of the industry is such that plant capacity could be increased rapidly if need therefor should arise. No figures on the estimated requirements for abrasives in 1941 or 1942 have as yet been compiled, but the industry feels that it can meet demands as they develop.

Jan 1, 1941

By Harry W. Campbell

In 1984 and 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied part of the Meadow Valley Range Wilderness Study Area (NV-050-156) in order to evaluate its identified mineral resources. The study area is located in Clark and Lincoln Counties, NV, about 50 miles northeast of Las Vegas, NV. The Johnston and Fitchett prospect, in the northern part of the study area, has more than 3 million tons of marginal perlite reserves suitable for many commercial uses. A preliminary mining feasibility estimate suggests perlite could be profitably mined from the study area; however, it is unlikely these perlite deposits will be developed in the foreseeable future because of unfavorable market conditions. Zeolite minerals occur in alteration zones adjacent to perlite deposits at the Johnston and Fitchett prospect, but high quality material is closer to potential markets. A metalliferous black shale unit containing 800,000 tons of subeconomic resources may extend into the study area at the Bradshaw vanadium prospect on the northwest boundary. Limestone, stone, sand, and gravel occurrences are wide-spread, but other suitable deposits in the region are more accessible to potential markets. Seven prospects in and near the study area were examined. The entire study area is leased for oil and gas exploration. A group of perlite placer claims covering more than 480 acres was located in the 1940&apos;s in the northern part of the study area. A small group of lode claims was located in the mid 1950&apos;s in the southwest part of the study area. No mining claims are currently (1985) held inside the study area. No mineral production is known from within the study area.

Jan 1, 1987

By Charles B. Carpenter

When a drilling well strikes a horizon in which there is a large volume of petroleum or natural gas under high pressure, danger of a blowout with disastrous results is imminent unless proper precautionary measures are taken. The history of oil-swell drilling has been marked by many blow-outs and wild wells, some of which-have caught fire and burned for long periods. Such incidents nearly always make headline news, but ordinarily few persons realize that what to them is an interesting newspaper item may entail great financial loss to the operator and frequently loss of life or personal injury to members of the drilling crew and others in the vicinity of the well. The blow-out, wild well, and crater are dreaded specters to every thoughtful person in the oil industry because of danger to life and property, underground damage to surrounding wells, dissipation of reservoir energy, and waste of irreplaceable natural resources that blow to the air or migrate to barren formations. Every operator drilling in high-pressure fields must be on the alert always to forestall any conditions that may lead to a blow-out, and his vigilance must not cease until a well is completed and oil, gas, or both are flowing to storage or market.

Jan 1, 1937

By Steven R. Munts

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 8,445 acres of the 20,650-acre Tunnison Mountain Wilderness Study Area in order to evaluate its identified mi nerd 1 resources. The study area is located in Lassen County, CA, about 8 miles northeast from Susanville. No mineral resources were identified in the study area based on literature, field observations, and sample results. No mines were operating in or near the study area in 1985, and no mines, prospects, or claims have been located in or within 1 mi le of the study area. The study area is underlain by Pliocene and Pleistocene volcanic units composed of basalt, andesite, rhyolite, and some pyroclastics. No metallic and only nonmetallic commodities are present in the study area. These included stone and sand and gravel. Although substantial volumes of basalt and andesite (stone) occur within the study area, no identified resources of these commodities were delineated. Sand and gravel is not economic because of small occurrence size and lack of local markets.

Jan 1, 1987