Search Documents

By Leonard Obert

This report describes a gage which, when used with my procedure for producing strain relief, will measure the resulting borehole deformation, From the borehole deformation the magnitude and direction of the principal stresses in a plane normal to the axis of the borehole can be calculated. The design considerations, mechanical construction, sensitivity, and stability of the gage are discussed. INTRODUCTION During the past two decades an increasing mount of consideration has been given to the problem of measuring and evaluating stress in rock around underground openings. Several investigators have made theoretical and model studies of the stress and (or) strain concentrations around simulated mine openings or in structural members, such as mine pillars or immediate roof. Other investigators have developed gages for directly or indirectly measuring stress or strain, and a number of reports present the results of measurements made with these gages. Because various methods and instruments have been developed, factors involved in this type of measurement will be briefly considered.

Jan 1, 1962

By E. R. Maize

This report is the third of a series on convergence of roof and floor in coal mines and subsidence of surface that accompanies it. The first papery dealt with extraction in a mechanized mine (Montour 10) having relatively short rib lines that retreat rapidly. The second 6/ dealt with extraction in a mine (Crucible) in which coal was loaded by hand and in which the rib lines were long and slow-moving. The present report deals with a mine (Gibson) in which conditions approximated those in the Crucible mine, except that the distance between room centers was considerably less and the pillars were narrower in consequence. Moreover, the average cover was less and the studies were made under the steep hillside of a stream valley compared with a gently rolling surface over the portions of the second mine studied. Gibson mine lies in the east-central part of Washington County, Pa., approximately midway between the Montour 10 and Crucible mines on a north-south line. A cooperative agreement covering the work was made with the Hillman Coal & Coke Co. through W. L. Affelder, vice president. This paper describes the methods used in the investigation, gives excerpts from the data obtained, and offers such generalisations as appear to be justified.

Jan 1, 1940

By Kevin Hennings

Screening efficiency models developed to date rely almost exclusively on empirical formulas based upon large amounts of acquired operating data. A screening model was developed using a combination of empirical coefficients and explicit mathematical expressions which quantify screening phenomena. A series of screening tests was run to supply data for purposes of correlation and empirical coefficient evaluation. The model has been implemented as a digital computer program. The validity of the modeling procedure has been established by laboratory testing. Results generated by the model have been used to compile an applications handbook, which can be used to predict screening performance in lieu of using the computer program.

Jan 1, 1982

By Pedro Lilienfeld

The objective of this program was the development, design, fabrication, and laboratory testing of a mine-worthy continuous respirable dust monitoring system (CRDMS). The operation of the sensor unit of this system is based on the light scattering intensity of the respirable fraction of airborne dust. The CRDMS is compatible with the typical environmental rigors that characterize coal mines and, in particular, the shock, vibration, impact, moisture and dust conditions prevailing at active training machines. The sampled area must be within the breathing zone of the mining machine's operator, whose dust exposure is to be monitored by the CRDMS sensor unit. Instantaneous, as well as shift-averaged dust concentrations, are displayed and recorded for later retrieval, Alarm indications and other diagnostic information are provided. The project was completed with the delivery of three sensor/display units (SDU), one data retrieval unit (DRU), two mining-machine-compatible power supplies, and two [auxilliary] battery packs.

Jan 1, 1983

To improve communications between mine workings and surface locations during emergency situations and for administrative purposes. The Approach: Development of a device for interconnecting phone systems which permits two-way communication between a public telephone and a mine pagerphone by authorized personnel. How It Works: The system, developed by personnel at the Bureau's Pittsburgh (Pa.) Mining and Safety Research Center, makes connections between the public phone line and mine pagerphone line. As shown in Fig. 1., incoming calls are sensed by the ring detector (4) and the system "answers" the call electronically. To reach the pagerphone system, the caller inserts an audible tone of fixed frequency through the microphone of his telephone. This tone is produced by a miniature, pocket-carried tone generator and is detected by a tone recognition circuit (5). When this hap-pens, relay, switching, and logic circuitry (6) closes the connections between the two phone systems. Simultaneously, a page activator (9) places a DC paging voltage on the mine phone line.

Jan 1, 1974

By G. Hakes

A data bank on bolter technology was assembled which included state-of-the-art industrial equipment as well as new equipment currently under development for the U.S. Bureau of Mines. This information was augmented by field visits to selected USBM contractors, mine operators and others for the purpose of obtaining a thorough understanding of present coal mine roof bolting safety and productivity problems. These direct contacts provided valuable insight regarding requirements for new bolting equipment necessary to assure wide user acceptance. Using this background material and information, a series of roof bolter concepts was developed offering improved operator safety with minimum impact on productivity. The concepts developed utilize existing componentry and technology wherever possible. All of the concepts feature a fully protected operator station located 6' to 10' outby the active bolt line and the hazardous rotating machinery.

Jan 1, 1978

By Fred D. DeVaney, C. W. Ambler

"Copper sulphate is a common flotation reagent for blende ores. Metallic iron also is present in the mill circuit, and a reaction between the iron and the salt would be in accord with well-known chemistry. The abundance of metallic iron in a flotation feed may be noted by even perfunctory examination. First of all the mine contributes metallic iron, then the coarse-crushing machines add their share, and finally the fine-grinding medium its portion. If the grinding is with cast-iron balls the amount of metallics is greater than when steel is used. Thus it is that much more metallic iron is present than would be indicated by noting the ball consumption. An estimate that the total amount of metallics is twice that supplied by the balls and liners might not be far amiss.That copper sulphate plates out on iron in an acid solution is well known, but since flotation is practiced commonly in solutions where acid has not been added this reaction has not been given sufficient thought.This problem has been the basis of a study undertaken jointly by the Mississippi Valley Station of the United States Bureau of Mines and the Missouri School of Mines and Metallurgy, at Rolla, Missouri. Its importance may be understood better when the tonnage of zinc ores now being treated by flotation in this country is considered. According to Gaudin4 5,536,244 tons of zinc or were treated by flotation during 1927. In these operations copper sulphate was employed as an activating agent; the amount per ton averaged 0.81 pound for straight sulphide zinc ores and 1.16 pounds for complex ores. Since such large quantities of zinc ore are treated by flotation and since metallic iron is always present, the importance of studying their reactions on each other and the effect of their reaction"

Dec 1, 1929

By Michael Kaplan

An investigation was conducted of the use of a mechanical rock splitter as the primary means for rock fragmentation in underground hard rock mining systems. Analyses and scale model tests showed that reasonably sized splitters that could be mounted on the booms of conventional drill jumbos were capable of fragmenting over a ton of rock per cycle. Detailed drill-split mining systems were developed for entry development, room and pillar, bench mining, and cut and fill mining. Economic analyses of these systems showed them to be generally competitive with conventional drill-blast methods. Except for bench mining, drill-split offered substantial cost savings over drill-blast. The investigation also included a technical evaluation of the mechanical splitter, an analysis of health and safety, and a determination of the potential applicability of drilling and splitting.

Jan 1, 1979

By D. Harrington

Seldom, if ever, has any mining hazard presented itself that some method has not been devised to control it to some extent; the degree of success of such control depends largely upon the intensity of desire to prevent suffering, injury, and death. The economic saving to be realized and the more definitely this is realized by all concerned, the more quickly and effectively will the hazards be handled is an important incentive to prevention of accidents. Preventing coal-mine explosions is by no means a complex problem; all that is necessary is sensible, conscientious, sustained effort. The fact that explosions can be prevented has been well-demonstrated by the record of the post few years; the average annual death toll from explosions for the 5 years 1906-1910 was 438, and for the 20 years prior to 1929 it was 265: during the past 4 years an average of only 32 deaths per year resulted from this cause, although the annual production during that time varied but slightly from that of 1906-10. This is a truly remarkable reduction, and if other types of mine accidents had been reduced in the same ratio only about 300 would be killed annually in our mines instead of the nearly '1,300 killed in 1936 and the approximately 2,000 killed annually for many years. Although frequency of occurrence of explosions has not lessened greatly during the last decade, their severity decreased markedly, which would indicate that effective means are being taken to prevent the spread of explosions, even though ignitions and their causes are not being handled nearly as effectively as they might or should be handled. Several large coal-producing States, which in the past have experienced numerous disastrous explosions, have been free from such disasters for continuous periods as long as 8 years in the relatively recent past. The application of rock dust to underground surfaces has been an important factor in preventing widespread explosions; some of the mast dangerous mines have been rock-dusted fairly adequately, and this has been amply repaid in the reduced severity of explosions, as heretofore indicated; however, many have applied rock dust apparently without giving much consideration to the amount required to prevent

Jan 1, 1938

By Travis Q. Lyday

Mineral production in Fiji, a group of 322 volcanic islands and atolls of Melanesia in the southern Pacific Ocean, continued to be dominated by gold. However, the Fijian mineral sector remained a minor factor as a source of export earnings, Government revenues, and employment, generating only 1% of the gross domestic product (GDP), estimated as $1.2 billion.2 The largest and most important mining operation was the Vatukoula gold mine on the north side of Viti Levu, the main island. The Vatukoula Mine has been in prduction since 1932, producing about 3.8 million troy ounces of gold and 1.3 million troy ounces of silver to date. In April 1983, the large Australian mining firm, Western Mining Corp. (WMC), assumed operation of the mine in a joint venture with Emperor Gold Mining Co. Ltd., which operated the mine previously. The WMC takeover of the mine management was expected to bring in additional capital and technological expertise in order to modernize operations, increasing both efficiency and output. During the year, rate of recovery was only about 75% of the gold contained in the ore and only 40% of the contained silver. Mining at the Vatukoula Mine was done using bath opencut and underground methods, with about 60% of the ore mined attributed to the underground operations.

Jan 1, 1985

By P. B. Grote

The report provides a general description of DOM technology, sources for DOM technology, and identifies approaches and requirements for acquisition by the Enterprise of DOM technology by conventional means. The approaches identified assume the Enterprise enters into a contractual/ joint venture arrangement with an uncommitted and competent systems management firm at various stages of the DOM system acquisition process. The approaches provide for training through work/study as well as through direct participation in acquisition programs. The potential success of the alternatives are evaluated in terms of the likelihood of the acquisition of an ongoing Enterprise economic DOM operational capability. The study concludes that sources exist and that the Enterprise should under-take the development of its own technical capability through conceptual design prior to selecting its source for systems management expertise.

Jan 1, 1980

By C. A. Geffen-Fowler

This report, sponsored by the Bureau of Mines, presents the results of an examination of the safety of the Blind Shaft Borer (BSB) shaft sinking system and an alternative modified BSB design concept in comparison to conventional shaft sinking technology. Detailed study of the two systems was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the BSB systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the two BSB systems was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that both BSB systems are safer than conventional shaft sinking. The potential risk of conventional shaft Sinking operations could be reduced by over 30%, on the average with the use of the original BSB system, and by an average of about 10% with the modified BSB. Design change recommendations to further improve the safety of these systems include a better fire suppression system, improved man haulage systems and more compact hydraulics. An operational safety manual was also developed for the modified BSB system.

Jan 1, 1981

By W. A. Dunkley, W. W. Odell

About two-thirds of the manufactured gas supplied to the public by the gas plants in the Illinois district is cnrbureted water gas. The leading generator fuel is coke, ma.de in by-product c.oke ovens or in retorts, chiefly from eastern gas coals. During the fall and winter of 1917-18, when the demand for coke by war industries and the restrictions of the Fuel Administration in connection with the transportation of coke from eastern States made it almost impossible for many gas companies to obtain their coke requireml'nts, several water-gas plants had to use bituminous coal as generator fud. Many operating difficulties were encountered, some of which were solved more or less satisfactorily in different plants. A number of plants attacked the problem rather blindly because facilities for making tests were lacking and because technical men were too busy with labor and supply problems to study thoroughly the conditions involved or to ascertain what other plants had done with this fuel. It was therefore with the hope of assisting the gas industry during this critical period, and of promoting the use of Central District coals for gas making, that the Illinois Mining Investigations, a joint agency of the U. S. Bureau of Mines, the University of Illinois, and the Illinois Geological Survey Division undertook the, tests discussed in this paper. • This report was compiled under the auspices of a technical committee appointed by Gov. Frank 0. Lowden to promote the use of Central District coals in gas manufacture as a war measure. This committee included the following representatives of the various agencies concerned: U. S. Bureau of Mines, E. A. Holbrook and W. W. Odell; Illinois Gas Association, C. W. Bradley and R. B. Harper; University of Illinois, Dean C. R. Richards, Prof. S. W. Parr, and Prof. H. H. Stoek; State Geological Survey Division, F. W. De Wolf, G. H. Cady, a.nd W. A. Dunkley. F. W. De Wolf was chairxnan of the committee and E. A. Holbrook was secretary.

Jan 1, 1924

By L. B. Phelps

A method is presented for the burial of potentially toxic spoil in high density zones or packages within spoil piles. Such burial could reduce the outflow of pollutants and thus minimize contamination of groundwater flows. Laboratory model studies using ammonium bromide tracer were performed to quantify the expected outflow mixing that could be achieved through package construction in spoils. Field drilling and geophysical density logging of spoils was carried out at three sites in Pennsylvania and Ohio to obtain a range of field spoil bulk density measurements and spoil samples. These data are analyzed to determine the relationships between spoil density and the controlling factors of lithology, depth, age, particle size distribution and mining method. A separate series of spoil permeability tests were performed in the laboratory to investigate the relationship between permeability and its related parameters. Research results are applied to the toxic package method to suggest guidelines for pack-age size, shape, density and placement for future field prototype development.

Jan 1, 1981

By G. T. Lineberry, W. J. Wiehagen

A Paradigm Shift As market economists, mine managers are interested in "staying in business" and even "prospering." Bottom-line results are the "order of the day." Concern for bottom-line results invokes questions such as: How much was produced? At what cost? And, was anyone injured? While these questions will always carry everyday emphasis at the mine, they are fundamentally lacking in that they often appear, especially to lower levels of management and to the production worker, as preeminent concerns. Driven by market economics, many organizations have decentralized, outsourced, downsized, restructured, and formed new coalitions. Investments in new technology and concentration on productivity have been part and parcel with these changes, contributing to improvements in both safety and efficiency. A reason for (and, perhaps a result of) these improvements has been the development of a highly experienced and flexible work force. These changes in mining present an interesting opportunity to modify a few paradigms about work life in general, and perhaps a few paradigms about how we invest in the miner, in particular. Studying these issues now might offer some interesting opportunities for the future, as the foundations for the next generation of mine workers are laid. With the average "experienced" U.S. miner five to fifteen years from retirement, perhaps a key determinant of future success in the world market might be how well we make the transition from today's work force to the work force of tomorrow. We can ill afford to wait a few more years to tap into the special knowledge residing within a veteran mining work force. The WCPM work Crew Performance Model, see pp. ) is one approach to defining, capturing, and transferring this expertise.

By Clayton M. Rumsey

The U.S. Bureau of Mines conducted a mineral resource survey of the Cinder Cones Wilderness Study Area (WSA) (CDCA-239), 10 miles east of Baker, CA, in 1983. The 44,299-acre WSA is underlain by Precambrian granite gneiss, Upper Cretaceous or lower Tertiary Teutonia quartz monzonite, and Quaternary basalt flows and alluvium. This mineral survey included an examination of two volcanic cinder mines, five lode prospects, two volcanic cinder prospects, and reconnaissance sampling in and near the WSA. The seven prospects are in the WSA; the two volcanic cinder mines are adjacent. No mines are in the WSA. In 1981, there were 61 placer and 3 lode mining claims in the WSA. Sample results from two prospects within the WSA contained significant gold and silver values; however, the mineralized rock is of limited extent and no resources were apparent. Alluvial samples taken throughout the WSA contained only traces of gold. Two volcanic cinder cones within the WSA contain an estimated 30 million tons of cinders. There are sufficient cinders outside the WSA to satisfy demand in the foreseeable future. Stone, sand, and gravel deposits are not resources because similar material is closer to markets. No evidence of energy minerals or geothermal resources was found.

Jan 1, 1985

By James C. Barker

The U. S. Bureau of Mines made a reconnaissance In the western Crazy Mountains for cobalt and associated metals as part of the Alaska-wide critical and strategic metals program. The area, located about 75 miles north of Fairbanks in central Alaska, is underlain by complexly faulted, predominantly clastic sedimentary rocks bordering the Tintina Fault system. Above background metal concentrations were found to occur in altered fault zones, tectonic breccias, soils, and ground water seeps and precipitates that either cut or are derived from the faulted clastic sedimentary rocks. Up to 0.115 pct cobalt and more than 2.0 pct zinc were detected in soil samples. Spring precipitates contained up to 1.3 pct zinc, 0.037 pct tungsten, and other metals. Some localities lacked cobalt but contained anomalous amounts of copper, lead, zinc, silver, and other metals. No outcropping of primary metallic minerals was located because of Colluvium and vegetation cover and extensive deep leaching. Therefore, whether the metal values encountered are due to primary deposits with economic development potential or are the results of concentration by ground water from low-grade sources is unknown. The presence of cobalt, nickel and zinc, and the identification of minor tin and tungsten indicate that further investigation is warranted.

Jan 1, 1983

By Ferron A. Olson

Natural bornite (Cu5FeS4) leached in ferric chloride or in sulfuric or hydrochloric acid solutions with oxygen showed several differences. In ferric chloride 80 of the copper was leached in two stages. The first (30 copper removal) requiring one minute was controlled by mixed kinetics (liquid ferric ion diffusion and chemical surface reaction). The second was controlled by formation of a surface sulfur layer and then diffusion through the sulfur. With oxygen in sulfuric acid reaction was slow and only the first stage was studied. Copper removal had an induction period. The bornite structure disappeared at 12% copper removal (also found with ferric chloride) and covellite formed on the surface with a species inside the particles having an x-ray structure similar to CuFeS2 but with composition Cu3FeS4 (also with ferric chloride). Copper removal was controlled by iron dissolution. Surface iron vacancies filled with Cu+ to give CuS while interior copper dissolution produced Cu3FeS4. Preliminary results with oxygen and hydrochloric acid showed 80% copper removal and sulfur as end products (similar to ferric chloride).

Jan 1, 1982

By Dana C. Reinke

Water well drillers are exposed to high levels of noise while working. NIOSH researchers have found that water well drillers are exposed to levels above 85dB (A) while performing certain tasks during a typical drilling job. Noise levels consistently over 85dB (A) during an 8–hour work shift are hazardous and can lead to hearing loss in workers. Finding ways to reduce noise exposure is difficult because of many factors. The work environment is constantly changing due to the location of jobs and environmental factors. The types of drill rigs required for drilling are expensive. Equipment can range from new to used (10 to 30+ years old). Drillers and owners can work together to prevent noise–induced hearing loss, and measures can be taken to reduce exposure to hazardous noise.[ ] Preventing hearing loss occurs through three stages. The first stage is removing noise from the source (i.e., drill rig). Various parts of a drill rig create noise besides the drilling rod. NIOSH researchers have examined noise levels of drill rigs. Some of the loudest parts of the drill rig include the compressor, engine, and cooling fan (Fig. 1). While removing the noise source from a worksite is ideal, the process would be expensive and difficult.[ ]

Jan 9, 2005

By H. F. Yancey

The investigations described in this bulletin are confined to a study of the washing characteristics of bituminous coals. The major part of the work was conducted by the Bureau of Mines in cooperation with the Engineering Experiment Station of the University of Illinois and the State of Illinois Geological Survey Division between 1918 and 1924, in accordance with the provisions of an agreement between these agencies. The washing characteristics of coals from many of the important coal-producing fields of the Eastern and Central States were examined. The coals of the Pacific Northwest States and Alaska have been studied separately by McMillan and Bird of the Northwest Experiment Station of the Bureau of Mines at Seattle in cooperation with the College of Mines of the University of Washington.2 OBJECT OF INVESTIGATION The object of the investigation of coal preparation by the Bureau of Mines has been to promote the production of better prepared coal and to facilitate the correct selection and design of coal-preparation plants by obtaining as complete information as possible regarding the washability of the various types of American coals and the treatment best suited to each. In addition, some attention has been given to the development of new methods of washing coal. The work naturally divides itself into three rather distinct steps: (1) Development of a systematic method of examining and testing a coal; (2) classification of the American coals on a basis of the occurrence of the impurities associated with the coal in the beds; (3) examination of one or more representative coals of each type.

Jan 1, 1929