Search Documents

By Robert W. Metcalf

Corundum, natural alumina, or aluminum oxide (A1203) is the hardest mineral known except diamond. Theoretical composition is Al 52.9 percent and 0 17.1 percent, but it always contains small quantities of impurities, chiefly silica, iron, and lime. The melting point of corundum is above 1950° C., and it is insoluble in the strongest acids. Its hardness (9 on the Mohs scale) varies slightly according to purity, and its specific Gravity ranges from 3.95 to 4.10, 4 being a fair average. The index of refraction is 1.760 to 1.768 and its streak is white. Luster is adamantine to Vitreous, come specimens pearly, and color varies widely from white, gray, pink, and blue to black, brown, or bronze. Gem varieties are transparent or translucent, and of more brilliant coloring - red, blue, yellow, purple, or green. Corundum occurs in opaque massive or block structure with parting planes little developed or only roughly delineated and in granular form as minute crystals or small, irregular grains interspersed throughout the contact zones of schists and gneisses.

Jan 1, 1944

By James R. Aggson

This Bureau of Mines report describes floor heave ground control problems that have been encountered in a new underground coal mine in West Virginia. Previous experience in the coal seam, the results of physical property investigations, and in situ rock stress determinations are discussed. The apparent cause of the ground control problems is the existence of a high, biaxial, horizontal stress field coupled with a floor member that has time-dependent deformation characteristics, A theoretical analysis of the failure process is developed. The analysis is assisted by finite element techniques. Mine design recommendations based on this analysis are presented.

Jan 1, 1978

By M. G. Wallis

This report presents the results of a study to develop a detailed mining method design based on longwall mining with sublevel caving. The method is applicable to low-dipping coal seams 20 or more feet thick such as are found in the western United States. The report covers (1) the development and description of the mining method, (2) evaluation of the engineering feasibility of the design, (3) estimates of productivity and recovery, and (4) an engineering cost analysis and economic feasibility evaluation of the mining method design.

Jan 1, 1977

Under contract from U. S. Bureau of Mines, Harza Engineering Company in cooperation with Eastern Associated Coal Corporation, conducted a ground control study of two mechanized longwall panels at the Federal Number 2 Mine. The mine is located in Northern West Virginia, and the coal is mined from the Pittsburgh Coal Seam. The prime objective of the study was to collect data which will aid in the proper selection of the longwall supports system and to control the entry caving problem. Instruments installed in the mine were borehole pressure cells, convergence recorders, roof sag recorders, horizontal roof strain indicators, differential floor movement systems, and lateral roof and floor movement systems. Instruments installed on the surface, above the instrumented longwall panels, consisted of slope indicator system, vertical bed settlement probe system and shear displacement detecting system. A comprehensive surface subsidence study was conducted in conjunction with the instrumentation. In addition to the instrumentation and monitoring, special tests were conducted to determine the bearing capacity of the roof and floor rocks, in situ modulus of coal, roof and floor rocks, and response of borehole pressure cells to ground stress. Cores of coal measure rocks were collected for the physical property tests. Face observations were made to detect various roof behavior parameters under the different jack setting pressures. This report essentially describes the instrumentation work, special tests and presents the data collected.

Jan 1, 1976

By S. H. Ash, E. M. Brooks

"Many of the hoisting slopes at the mines in the State of Washington are driven on extra steep dips. To facilitate hoisting they are driven wide enough to provide two tracks. The cars are handled by high-speed, first-motion electric hoists and the trips run in balance.The State mining laws a provide that special man-cars be provided on slopes of 20° or more and that no one be allowed to ride while any loaded car is being hoisted in any slope in a mine. Obviously, in addition to the fact that it is more or less hazardous to ride while an empty trip is being hoisted, considerable hoisting time is lost during the day if some one has to ride the trips in the slope.Owing to the locations of pumps and various types of equipment, more or less travel is required up and down the slope. Not only to provide a proper safety factor but also to comply with the law, some other means of transportation in an¬other passageway is desirable. This is sometimes recognized in large mines by pro viding separate hoisting shafts, or slopes, and necessary equipment, which are use for transporting men and material. The handling of material in itself would justify the system in most large mines.The following description of an automatic electric man-hoist was prepared from data furnished through the courtesy of Mr. Thomas Murphy, superintendent of the Northwestern Improvement Company's mines in the Roslyn-Cle Elum coal field.The special features of this hoist are that no hoistman is required and its operation is always under the control of the person or persons riding the trip.The hoist was installed at mine No. 5, Roslyn, Washington, to provide a means of entering and leaving the mine on idle days or at night when no hoistman was on duty and to make it unnecessary to use the main hoist for a man trip during working hours. It has been in operation for about two years and has given very satisfactory service.The hoist, with all accessories, is housed in a concrete building 200 feet back from and in direct line with one of the main airways. One car with a capacity of six men operates over a distance of 1,200 feet on a 38° pitch.The wiring details of the electric circuits which control the operation of the hoist are shown in Figure 1-a.The hoist is driven through a worm gear by a 500-volt shunt-wound direct-current motor at a car speed of 120 feet per' minute. A gravity friction brake with magnetic release is mounted on the- motor shaft and is wired in multiple with the motor field coils. The hoist drum is also equipped with emergency friction brakes, which operate by gravity and are released, in case of overspeed, by the governor geared direct to the drum shaft. When these brakes set the control circuit is opened at contact 2E-2C and the motor stops.If the descending car meets some obstruction and is stopped, the hoist continues to run and unwind the rope. To guard against this occurrence, a weighted sheave wheel rides the rope 4 feet from the drum, and if the rope becomes slack the rider drops downward and opens the contact 2C-2E which stops the hoist.Limit switches, S1 and S2, are located on the hoist indicator, which is connected to the drum shaft through sprockets and chain. The pointer P indicates the position of the hoist at all times."

Jul 1, 1930

By James Paone

Land utilized by the mining industry from 1930 through 1971 amounted to 3.65 million acres, or 0.16 percent of the land mass in the United States. Land reclaimed during the same period was 1.46 million acres, or 40 percent of the land utilized. This report includes data on land use for wastes from underground and surface mining, for wastes from mill operations, and on subsidence. Data on land use and reclamation were obtained from operating companies, mining organizations, appropriate State agencies, and others concerned with such activities. The 10 leading States in land used for mining in 1971 were, in decreasing order, Kentucky, Pennsylvania, Arizona, Ohio, California, Florida, West Virginia, Illinois, Minnesota, and Indiana. Mineral commodities accounting for a major portion of land use are, in decreasing order, bituminous coal, sand and gravel, stone, copper, phosphate rock, iron ore, and clay; for coal, these commodities are produced principally by surface mining operations. Reclamation over the 42-year period was largely on lands utilized for surface mining of bituminous coal. New surface mining methods, particularly for coal, incorporate some form of land restoration.

Jan 1, 1974

By Lulie H. Crump

Salient information on reserves, production, and consumption of fuels and energy by State is summarized in this Bureau of Mines publication. Reserve and production data are shown for each of the fossil fuels (coal, crude oil, natural gas liquids, and natural gas) and for uranium. The consumption data of each of the major consuming sectors (household-commercial, industrial, transportation, electric power, and miscellaneous) are broken down by energy source (coal, petroleum, natural gas, hydropower, and nuclear). In addition, total energy consumption in the Nation in 1974 is compared with consumption in 1973 and 1975 (preliminary data).

Jan 1, 1977

By R. Luhrman, E. Christ, B. Gores, S. Fischer, E. Johanning

North American railroad locomotive operators (engineers and conductors) are exposed to multi-axis vibration and shocks (1, 2). A recent epidemiological survey showed a prevalence of serious type of neck and lower back disorders nearly double that of a control group (3). Ergonomic working conditions are important co-factors in a vibration and shock exposure risk assessment (4, 5). The goal of this study is to illustrate typical work stations (cabs and seats) in US/Canadian type locomotives and assess shock related exposure risk by calculations of the new proposed shock risk indicators according to the new ISO 2631-5 (2004) (6). Methods Locomotive cab and seat inspections were conducted and operators’ activities were assessed by a trained observer. Field measurements (n=50) were obtained during normal revue service following generally accepted guidelines (ISO 2631 (1)). A sub-sample of n=20 locomotives were selected for the calculation of proposed shock indicators (ISO 2631 (5)). Results There has been little change in basic locomotive cab and seat design in the U.S.. Two locomotive cab design concepts are used: the Association of American Railroad (AAR) Control Stand and in newer series wide-body locomotives the “Control Consol” (Figures 1-2), with varying seating conditions, but frequently subjecting the operator to an awkward body posture in addition to the vibration and shock exposure. [ ]

Jan 6, 2006

By J. C. Gerdeen

It is of upmost importance to keep the size of the program to a minimum for the computer being used. One way is to reduce the size of the data bank by adjusting the large common array A in the main program (page, line 32) and the statement following the assignment of A. The current value of A is 35001 and is optimized for the UNIVAC computer with 5,000 words of useable storage. Another way to reduce the required storage is to overlay the program. That is, to have in the computer only the subroutines which are being used. In large finite element codes, overlays or segmentation of the program is a necessity. The code presented here has three levels of segments and are presented graphically in the tree in Figure D-1.

Jan 1, 1976

By K-H. Frohne

This report presents a study of the Cooper sand of the Fork Run pool of Warren and McKean Counties, Pa., and a prediction of the secondary oil recovery by gasflooding the reservoir. A computer program employing a modification of the Craig, Geffen, and Morse secondary recovery calculation was used to make the gas flood performance forecast and is presented in the appendix. The Cooper sand reservoir in the Fork Run pool lies at a depth of about 1,900 feet and covers an area 1/2 mile wide by 2-1/4 miles long. Original oil in place is estimated to have been 8,266,000 STB. The primary recovery mechanism is solution gas drive, and ultimate primary recovery may reach 20 percent over a well life of 90 years. Two computer predictions were made for gas flooding the Cooper reservoir. The first was for a 25-acre pilot five-spot utilizing existing wells, but project economics were poor since only 25 percent of injection gas is utilized for pilot oil recovery. Recovery was 71,000 STB, or 22 percent of oil in place at flood initiation, but required 25,700 scf gas injected per STB of oil recovered. In the second prediction, pilot area performance was projected for the entire Fork Run pool, and economics became good. Recovery was 1,753,000 STB from 25 five-spots after the injection of only 6,400 scf per STB of oil recovered.

Jan 1, 1969

By D. K. Caddel

Several problems exist with the present design of coveralls used by miners in low coal (seam height 48 inches or less). The back portion of the coveralls often tears when roof bolts or rough areas in the roof are hit. Movement in the shoulder area is restricted. Female low coal miners find it difficult to purchase coveralls that fit properly, and must remove both their hard hat and safety belt in order to urinate and defecate. The objective of this research was to design coveralls which would alleviate these problems. The following features were incorporated into the coveralls; padding in the upper back area to avoid tearing, an action pleat in the shoulders to increase mobility, an inseam zipper to more easily allow miners to perform their bodily functions, and reflective tape to increase visibi¬lity of the miner. A heavyweight denim fabric was used to increase warmth and durability of the coveralls. The coveralls were assessed K long four parameters (comfort, safety, worker productivity, and fabric suitability) using both an in-field assessment by low coal miners and simulation studies. The experimental coveralls proved superior to conventional coveralls along all four parameters. Work clothing sizes for female miners were developed.

Jan 1, 1982

By Robert J. Pokora

This report summarizes the work performed under USBM Contract No. J0100038, "Demonstration of Noise Control Techniques for the Crushing and Screening of Nonmetallic Minerals." The objectives of the program were to: a. Identify the prevalent sources of crushing and screening noise in portable and stationary plants b. Design retrofit noise control treatments for those sources c. Field test control treatments under actual operating conditions. A census of the nonmetallic industry was performed to determine the number and types of crushing and screening equipment. Based on the census, eight plants were selected and surveyed to assess the variety of noise sources, determine the worker noise exposure to those sources, and to identify possible constraints that had to be considered in designing and installing the retrofit controls. Three plants were selected from those surveyed and retrofit noise control treatments were designed, including: a. A primary crusher operator control booth b. Screen decks made of resilient cloth c. Screen feedbox impact pads d. Rubber feed plate for secondary crusher e. Rubber feed chute linings for secondary crusher f. Noise attenuating curtain for secondary crusher. A new primary crusher control booth was installed at one plant, and the operator noise levels were reduced from 97 dBA to 78 dBA. Screen noise at the two secondary crushing plants was reduced by 3 dBA to 7 dBA; crusher noise was reduced by 5 dBA at one of these two plants. Noise levels at normal outside operator and cleanup locations were reduced by 4 dBA to 7 dBA at one secondary plant, but operator/cleanup noise levels were not significantly reduced in the second plant due to rapid wear of installed materials. At one of the two secondary plants the retrofit noise control materials displayed excellent wear characteristics. The rapid wear of retrofit materials at the second plant was due to improper materials being supplied and changing circuit conditions.

Jan 1, 1982

By Louis Schaffer

This report characterizes several coal Dine mobile equipment operator populations with respect to age, mine experience, machine operator experience, and training. The information is used to demonstrate a method of normalizing the injury data collected by the Mining Enforcement and Safety Administration-Health and Safety Analysis Center.

Jan 1, 1977

By Geo. S. Krueger

This paper, describing mining methods and costs at the Judge mine Park City, Utah, is one of a series being prepared by the Bureau of Mines on mining practices in the United states. ACKNOWLEDGMENTS The writers acknowledge the assistance of E. D. Gardner, supervising engineer, Southwest Experiment Station, Bureau of Mines; Paul H. Hunt, mine manager, Park Utah Consolidated Mines Co.; Wm. Osika, chief mine accountant; and Eric Neilson, assistant master mechanic of the mine.

Jan 1, 1938

By J. D. Davis

THIS REPORT gives results of an investi¬gation of the carbonizing properties of coals from Pittsburgh bed, Jamison No. 9 mine, Marion County, W. Va., and from Upper Freeport bed, Bull Run No. 1 mine, Preston County, W. Va. The study included Bureau of Mines-American Gas Association tests at 800° and 900° C. and various chemical and physical tests designed to evaluate the plastic, expanding, and agglutinating properties of coal. A blend of each coal was carbonized in the 500-pound slot oven. The carbonization sample of Pittsburgh coal contained 2.7 percent moisture, 35.8 percent volatile matter, 54.4 percent fixed carbon, 7.1 percent ash, and 0.9 percent sulfur. It contained 60.9 percent fixed carbon on the dry, mineral-matter-free basis and had a heating value of 14,780 B. t. u. per pound on the moist, mineral-matter-free basis. It therefore ranks as high-volatile A bituminous and was blended with low-volatile Pocahontas No. 3 coal. Upper Freeport coal contained 2.8 percent moisture, 27.7 percent volatile matter, 60.9 percent fixed carbon, 8.6 percent ash, and 1.0 percent sulfur, as carbonized. It contained 69.5 percent fixed carbon on the dry, mineral-matter-free basis and therefore ranks as medium-volatile bituminous. It was blended with high-volatile A Pittsburgh coal from Allegheny County Pa.

Jan 1, 1952

By James E. Aplin

Previous studies have shown that fracturing of roof strata precedes ultimate failure, and that the fracture development causes an accompanying increase in the apparent resistivity of the strata. Using this principal, a microprocessor controlled resistivity roof fall warning system (RRFWS) was developed that automatically sequences through and records up to 32 electrodes that may serve as either voltage or current electrodes. This capability permits increased coverage with a minimal number of required electrodes. The data is stored in a nonvolatile memory and on an optional printout, making the system nonsusceptible to loss of mine-power. To further save battery power, the system's electronics shut down between readings, except for a carbon molybdenum steel real-time clock. At a preprogramed interval, the RRFWS reactivates and repeats the sequence. If the absolute change or the rate of change of resistivity exceeds a predetermined limit the system is capable of sounding an alarm. In addition to the monitor, a stainless steel mod led split-set electrode was also developed that permits long-term corrosion-free contact.

Jan 1, 1983

By Rudy J. Matetic

The National Institute for Occupational Safety and Health (NIOSH) at the Pittsburgh Research Laboratory (PRL) is conducting research to reduce the noise exposures of roof bolting machine operators and to prevent additional cases of Noise Induced Hearing Loss (NIHL) thru the development of engineering noise controls. This paper describes and evaluates an engineering noise control for the roof bolting machine, namely the collapsible drill steel enclosure. The results of the evaluation demonstrated that using the collapsible drill steel enclosure provided a 7 dB(A) reduction in sound pressure level at the operator?s position of a roof bolting machine.

Jan 1, 2008

By F. E. Armstrong

An instrument using a gamma-ray backscatter technique for determining the weight-percent incombustibles content of coal dust and rock dust mixtures in coal mines has been built and tested. The unit gives a direct readout in per-cent incombustibles for coal mine dust mixtures containing between 50 and 100 percent incombustibles; calibration of the device requires using a sample of the rock dust employed; this is usually limestone but occasionally dolomite or gypsum. A small americium-24l source is used with a scintillation detector whose output feeds a rate meter. The source-detector geometry used was chosen to reduce the effects of variation in bulk density. Accuracy of the system is within ±3 percent for most mixtures. The instrument is portable and completely self-contained; the rechargeable batteries supply power for 300 to 400 determinations.

Jan 1, 1974

By E. G. King

The literature contains little thermodynamic information regarding inter-oxidic compounds of the ferroalloy elements and, as a result, thermodynamic considerations of extractive and utilization processes involving these elements have been hampered. As part of a Bureau of Mines program to improve this situation, this paper reports the heats of formation of three calcium vanadates and two magnesium vanadates. There were no previous similar data for any of these compounds. The experimental method was hydrochloric acid solution calorimetry, using calorimetric reaction schemes involving the vanadates and their component oxides. The results were expressed as heats of formation from the component oxides and from the elements. Corresponding free energy of formation values were calculated. The data show that the calcium and magnesium vanadates are stable with respect to all possible decompositions in which vanadium remains pentavalent. This conclusion is similar to the one drawn by Koehler6 for three sodium vanadates.

Jan 1, 1962

By M. C. Bleiweiss

Various light sources were evaluated for use in a fiber optic lighting system for mining machines. It was determined that a metal halide arc lamp was best because of its resistance to damage from shock and vibration and the high luminance of the arc. Measurements were made of the percent transmission of the ½ inch thick glass window and the fiber bundles, the total lumen output of the diffuser assembly with a known input and of the average surface luminance of the diffuser assembly. These data were then used to calculate the theoretical output of the system given an estimated input from the source. A prototype 55 watt, single-ended metal halide source was then developed. In order to provide greater efficacy and higher throughput through the fiber optic cables, a variation of the lamp with thallium iodide added to the fill was developed. The lamp was modified and a ballast was developed to allow it to hot restrike.

Jan 1, 1986