Search Documents

By Cathy Aimone-Martin, Kristin Dunlap Kolden

Blasting was conducted for the Army Corps of Engineers (Corps) in the Columbia River near Saint Helens, Oregon during 2009 and 2010 to deepen the navigation channel as a final phase of a dredging project to accommodate larger container ships. The Columbia River Channel Improvement Project (CRCI) required 4 months to blast and dredge 300,000 yd3 (229,366 m3) of basalt from the bottom of the channel to allow Post-Panamax vessels with drafts up to 50 ft (15.2 m) access to the Ports along the River. Explosives charges were limited to 90 lbs (40.8 kg) per delay for the protection of fish and marine life in the area. A fish mortality study and marine mammal monitoring program was also required by the Corps. Underwater overpressure monitoring was required for each blast and peak overpressures measured 10 ft (3.1 m) above the river bottom 140 ft (42.7 m) from the closest blast hole were not to exceed 70 psi (483 kPa) with a cautionary level of 40 psi (276 kPa). Specifications required sampling rates of 500k S/s and PCB Peizotronics tourmaline pressure sensors. The Corps granted permission to co-locate additional ceramic-type sensors at different sampling rates to design redundant monitoring systems 140 and 300 ft (42.7 and 91.4 m) from blasting and develop a site-specific overpressure attenuation model for the project. This paper presents the correlations of overpressure with cube-root scaled distance factors, a comparison of measurements using three different pressure sensor systems, and a discussion of blast design influence on overpressure measurements.

Jan 1, 2014

By M E. Hanson, K Chong, R H. Jacobson, S C. Way

To create conditions for economic rates of mineral recovery in a deep, hard rock mass, enhancement of naturally occurring permeability is necessary, and may be achieved through explosives detonated in boreholes. Previous theories of explosively created permeability are reviewed and found to relate permeability solely to the degree of fracturing, neglecting porosity. A theory is presented that includes both fracture density and porosity, and its results are applied, together with a knowledge of explosive behavior, to derive design parameters for in-situ mining.

Jan 1, 1983

By D. Lee Petersen, Travis Davidsavor

The 2003-2004 expansion of a Duluth medical center required rock blasting adjacent to the existing structures, a Mn/DOT retaining wall and other urban structures. This case history describes the methods of a blast damage assessment, based on blast parameters, excavation locations, and critical vibration receptors (including surgical suites, a linear accelerator and a major retaining wall). The assessment concluded that blast vibrations could be controlled, by limiting charge weight, to eliminate impact at the critical receptors. Prior to construction, we conducted preconstruction surveys on structures susceptible to vibration damage. During construction, we reviewed submittals, observed test blasts, reviewed blasting logs and monitored blasting vibrations. Up to 13 seismographs were used simultaneously. Close coordination with medical center operations personnel was necessary to prevent impacts to critical medical procedures. Measured vibrations were clustered around the predicted values, and attenuated at the predicted rate. High-frequency blast induced ground vibrations induced low-frequency vibration of an adjacent MnDOT retaining wall. Medical center structures were observed to significantly attenuate the ground-borne vibrations. This paper was first published in the Proceedings of the 56th Annual Geotechnical Engineering Conference, 2008, at the University of Minnesota.

Jan 1, 2010

By Frank Sames

Blast vibration and airblast overpressure signals are generally rated and compared only by their maximum amplitude and the principal frequency associated with the peak pulse. The scaled distance concept is often used to predict peak amplitudes and can be applied for blasts in the same area of a mine to evaluate the statistical properties of a set of readings.

Jan 1, 1997

By P Bellairs

The Hamersley Province is located 1OOOkm to the North of Perth .the Capital City of Western Australia and is of major economic significance due to the mining of extensive deposits of Haematitic Iron Ore for both domestic and export use. A small but significant proportion of the waste associated with these deposits presents problems due to its ability to spontaneously combust and react with explosives resulting in premature detonations.

Jan 1, 1996

By Ken Tunnel

In the spring of 2005, the Lake Superior Chapter of the ISEE invited me to speak about raw materials used for blasting, anhydrous ammonia and the effect of this important feedstock on the cost of ammonium nitrate.The invitation was extended because our company is involved in trading ammonia and the production of ammonium nitrate. In a response to a request to update that presentation, it struck me how events such as hurricanes Katrina and Rita can change the landscape of our businesses.

Jan 1, 2007

By Mark S. Stagg, Rolfe E. Otterness, Farrokh Djahanguiri

The U.S. Bureau of Mines (USBM) evaluated empirical equations that predict fragmentation from underground stope rounds. Controlled blasting is necessary for creating leaching stopes that maximize the recovery and minimize backbreak of the perimeter wall. This paper presents the fragmentation results from one of the three drop-raise blasts used to develop a reduced-scale cylindrical stope, 1.8 m in diameter and 6 m in height. The stope is located in the Colorado School of Mines Experimental Mine (Edgar Mine) in Idaho Springs, Colorado. This stope is part of a USBM research effort to determine the feasibility of incorporating in situ leaching of rubblized stopes into active underground metal and nonmetal mines.

Jan 1, 1994

Casting design for bench blasting in surface coal mines is a new focus and a fairly recent success. This study aims at the development of a mathematical model to predict the throw of overburden material based on geological conditions of a bench and charges in blast holes. The procedure, derived on the basis of blasting theories and dynamics of the multiple-particle system, explores the mechanisms of casting rocks into pits. Implementing the model with a computer program is a part of the study. The computer program will supply quantitative data for evaluation. It serves the purposes of verification for the model and, hopefully, field applications.

Jan 1, 1988

By Andrew P. Ritter, Douglas A. Anderson, Stephen R. Winzer

We have adopted a unified approach to blast design. Based on earlier research, we chose minimum relief of 3.4 ms/ft between holes in a row and 8.6 ms/ft between echelons to produce good fragmentation. A model has been created which generates the expected ground vibration frequencies from a particular delay pattern. Within the relief guidelines, blast designs have been created to shift the expected frequencies of the ground vibration above the resonant range of residential structures. A programmable sequential blasting machine was used to delay circuits. An extensive three-month seismic monitoring program determined that this approach is successful. From data collected for over a year, we have determined that crusher throughput is up about 10%, frequency modification has been largely successful, peak particle velocities have generally gone down by a factor of 2, and neighbor complaints have decreased drastically.

Jan 1, 1982

By Mike McGill, Steven P. Case, Mark Spaulding

The General Crushed Stone Company at Doswell VA. decided to open a new pit to expand their reserves. The elevation of the property was 136 feet above the present primary crusher. The project required driving twin tunnels under the highway to access the primary crusher from the new property. A shaft was needed to pass blasted rock to the tunnel elevation where it's loaded and hauled to the primary crusher. In addition, a ventilation shaft was required to provide adequate airflow. Dynatec Mining Contractors Inc. Lakewood Colorado was subcontracted to handle the tunnel and shaft development.

Jan 1, 1993

By Lawrence C. K Hu

The release of load mechanism during rock breakage by explosives was founded by Dr. T. N. Hagan & published at the Sixth International Colloquium on Gasdynamics of Explosions and Reactive Systems Stockholm, Sweden, 1977.

Jan 1, 1995

By A Gene Riggs

The Cerrejon Coal Project in Colombia, South America is one of the largest coal mines in the world. The mine is located in northeastern Colombia on the La Guajira penninsula. The area is in a remote valley 132 miles east of the city of Barranquilla.

Jan 1, 1984

By I. Petropouleas, J. Croll, R. Bassett

A programme of tests on controlled internal explosions to a class of circular reinforced concrete columns, has allowed the relationships between the blast energy and the extent of local damage to be understood. These tests have also demonstrated the important additional effects on the damage levels of preexisting axial loads.

Jan 1, 2006

By Valerie A. Rhodes, Catherine T. Aimone

Often blast damage litigation involves structural damage which clearly is not blast related. The fact that structures are observed to be damaged when blasting has taken place in the near vicinity of these structures does not necessarily mean that the damage was caused by blasting. If careful blasting and seismograph records were kept by the blaster which decisively indicate damage is not blast related, then other causes of structural damage need to be assessed. These include problematic soil characteristics and long-term changes in climate or subsurface soil moisture. This paper presents the evaluation process required to investigate soil problems leading to damage often attributed to blasting.

Jan 1, 1991

By Karl E. Burger

Recently an experiment was completed at the Golden Sunlight Mine, a property owned by Placer Dome Inc. of Vancouver, British Columbia, to measure the Body Waves entering their highwall created by blasting. The purpose of the study was to assess the damaging effects of blasting on the highwall, in order to further slope stability. Stress and Strain experienced in the earth that is created as a result of blasting can be determined by knowing several important pieces of information. These include the compressional and shear wave particle velocities initiated by blasting, the Body Wave travel velocities in both the shear and longitudinal direction, and the densities of the rock in question. A series of equations based on wave theory can then be used to determine the stress and strain affecting the highwalls. The Blasting Engineer can then use this information to design blasts that create peak particle velocities less than levels that maintain the integrity of the highwalls. This paper first discusses the experiment used to measure the Body Wave velocities. It then traces through the subsequent calculations necessary to generate the information needed by the Blasting Engineers, the Mining Engineers, the Geological Engineers, and the Geophysicists to design blasts and develop open pit plans to alleviate unstable highwall conditions.

Jan 1, 1989

By K Ramachandra Rao

Joints, fractures and other structural defects bring anisotropic character Into a rock mass. Conventional methods of blast design In a rock mass consisting phyllites, mica schist etc., which are characterised by the presence of closely spaced, nearly vertical planar Joints, result In formation of large slabs which cannot be handled by the excavation and loading equipment without resorting to secondary blasting. Frequent secondary blasting Is not only expensive but also, Is a source of environmental hazard. Interruption of production cycles frequently, leads to uneconomical mining. This problem could be minimised by designing blasts which produce forces whose components along and across the joints/fracture planes Is lust sufficient to break the rock mass In both directions. Rock mass strength can be assessed from field and Laboratory tests. Projecting structural features with respect to bench orientation on a stereoplot helps In assessing magnitude and direction of force vectors required to fragment the rock mass to the desired size range.

Jan 1, 1995

By Rodger Andrews

High cost - low productivity mining methods at the Homestake Mine forced the need for a new and safer means of ore extraction. Vertical Crater Retreat (VCR) was introduced in 1978 and accounts for over 50% of the underground mine production today. Many advantages can be attributed to this form of "bulk mining"; including steady production, decreased labor costs, and the ability to mine bulk stopes in the lower portion of the mine. However, safety and high productivity are the two major advantages. This paper will deal specifically with crater blasting and the application of mass blasting techniques in Vertical Crater Retreat slopes.

Jan 1, 1988

By Juan Carlos Vasquez, Romel Villanueva

We present the results of our field research on the variation of the density of the gassed explosives and their influence on the blasting results in the Peruvian mines: Yanacocha, Toquepala and Antamina. Currently, 90% of Peruvian mines uses gassed explosives, for their economic and technical benefits. But new practices and design criteria have had to be adopted, and the most important a careful control of the in-hole density, whose variation in the depth of the hole strongly affects the detonation process.

Feb 1, 2020

By Joe Strobbe, Kevin Joe

The U.S. Bureau of Reclamation awarded PCL Civil Constructors the project to build a new visitor's center and parking lot structure at the Hoover Dam. The excavations for these structures present many blast design challenges. The visitor center, a 30 foot deep excavation was blasted in the Nevada side of the canyon wall, 600 feet above the existing power plant. This excavation also included a through-cut underneath the existing road that carries the traffic over the Dam between Nevada and Arizona.

Jan 1, 1993

By Floyd W. Crump

New technology in video equipment, such as Super Video Tapes, Super Video Camera Recorders equipped with high speed electronic shutters, and VCR's with editing capabilities make it possible to resolve high speed events to still frames with an event elapsed time of 17 milliseconds (ms). This is far from the 2 ms resolution available with a High Speed 16 mm Film Camera such as the LOCAM at its maximum 500 frame persecond speed, but is adequate for many field blast evaluations.

Jan 1, 1991