Search Documents

By G. G. Barbante

An understanding of the thermodynamics of smelting copper anode slimes is a prerequisite for improvements to the process. During slimes smelting, a silver-copper selenide matte is formed and subsequently oxidised to silver metal. As part of a series of investigations, molten silver selenide matte was oxidised at 1 100 degrees C with pure oxygen. The chemical potential diagram for the system was developed and used for qualitative prediction of the results of the experiments. A simple, computational thermodynamic model of converting is presented, the adjustable parameters of which were determined by matching the model with the experimental results. The practical usefulness of the model was demonstrated by predicting the effect on silver recovery of smelting temperature and of using either oxygen or air as the smelting gas

Jun 21, 1905

The reduction of zinc from slags by a molten, carbon-saturated bath was examined in a laboratory study under conditions of continuous slag feeding. The results show that it is possible to reduce the bulk of the zinc from the slag before there is a net reduction of iron. However, the recovery of zinc was not as high as in batch tests performed in an earlier study. Lead in the slag was reduced simultaneously with the zinc to very low levels and was volatilised. Copper in the slag was reduced and dissolved in the alloy. An attempt was made to identify potentially commercial ways of treating zinc slags using an iron bath. The approaches that appear to have the greatest potential are reduction in a batch process using electrical heating and reduction in a continuous process with co- or countercurrent flow of the slag and alloy. In the latter the alloy would be prepared in a separate furnace before being contacted with the slag. The purpose of this would be to superheat and carburise the alloy so that no additional heat or reductant would have to be supplied in the slag-alloy reactor

Jul 1, 1991

By R. Lahtinen, M. Tiainen, R. Salminen

The application of similarity analysis derived from regional geochemical mapping data to the location of Ni-bearing intrusions was tested in southwest Finland, where a well-known nickel belt is situated. Samples of till from the vicinity of the Vammala and Kylmakoski Ni-Cu deposits, which were collected independently of the Geological Survey of Finland's regional geochemical mapping programme, were used to provide geochemical modelling data. The data consist of the aqua regia-leachable concentrations of 20 elements from the less than 0.06-mm fraction of glacial till. The variables used in the similarity analysis were selected on the basis of a factor analysis in which the method of oblique rotation was used. A hierarchical clustering of the modelling samples produced two main groups. The first group was described as the "nickel deposit environment model" and the second as the "nickel deposit location model". The data for the standardised variables were compared sample by sample with the model data by similarity analysis using the Simana program with a cos theta measure of pattern similarity. The nickel deposit environment model delineated the known Ni belt and indicated an extension to the east. The nickel deposit location model identified target areas of reasonable size with the greatest potential for Ni ores within the nickel belt

Dec 1, 1991

By J. A. Finch, D. Lin

The robustness of the large-sections correction procedure, Hill's fast approximation, Barbery's correction and the PARGEN correction was examined by comparing their ability to reconstruct the true liberation distribution using sectioning data from computer-generated spheres. The results indicate that the flexibility of a correction procedure is related to the assumptions it makes about the continuity of the liberation distribution, locked-particle characteristics and ore texture. Overall, the large-sections procedure appeared to be the most generally applicable. The Hill fast approximation performed well, but this was probably because it partially incorporates the sphere model; the performance of the PARGEN and Barbery corrections varied from case to case.

Dec 1, 1995

By G. Richards

Research shows that having more women in the top mining jobs can bring bottom-line benefits. Mining companies are starting to embrace the need for greater gender diversity at board and senior management levels, figures and examples are given.

Jul 1, 2015

By R. G. Garrett, A. J. S. Geddes

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). The 1986 geochemical survey was successful in recognising all the previously known mineral occurrences of significance in Jamaica, in outlining areas not previously believed to have mineral potential and in stimulating fresh appraisals of old occurrences in terms of their potential for new commodities. This has resulted in a very significant increase in mineral exploration activity in Jamaica

Jul 1, 1991

By Xiao Min You, D. R. Swonbourne

Smelting of Cu anode slimes involves the use of a slag to hold the oxidised Cu, but some Ag is also inevitably oxidised to the slag. The solubility of Ag in sodium silicate slags at 1 100 and 1 150 degrees C has now been determined over a very wide range of oxygen partial pressures. Silver was found to be present in the slags both as neutral atoms and as AgO(0.5). The activity coefficient for atomic Ag was a very strong function of slag composition and temperature, whereas that for AgO(0.5) was much less affected by slag composition and was almost independent of temperature over the limited range examined. The results reveal that the dissolved Ag cannot be fully recovered by reduction of the slag with very reducing gases

Jun 21, 1905

By M. T. Styles, E. Condliffe, R. C. Leake, R. J. Chapman, D. J. Bland

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. Quantitative point analysis and microchemical mapping identified 52 different types of mineral in inclusions, usually ranging in size from 5 to less than 1 micrometre, inherited from source bedrock. A combination of grain chemistry, heterogeneity and inclusions provides a grain signature reflecting the type and history of source mineralisation. Several grains from an alluvial site are needed, to allow for bedrock variation and the presence of inclusions in only 10-20% of grains. A total of 1 530 grains obtained from 30 localities in Scotland were of ten types, two of them minor variants. Two types in the Highlands may be related to centres of Caledonian igneous activity, but the most widespread is likely to have been of deep-seated origin and structurally controlled. Gold in the Ochil Hills is probably from a source associated with Devonian andesitic activity. In the Southern Uplands, grain types reflect two separate episodes of mesothermal lode gold mineralisation and relationships with Permian red beds/mafic volcanics and with Tertiary dykes

Jun 19, 1905

By C. J. A. Mcewan, C. M. Rice

The Rosita Hills contain rich, vein- and breccia pipe-hosted precious metal deposits. Volcanic activity occurred in two cycles - an early, mainly andesitic cone-building phase that terminated in the formation of a caldera and breccia pipes and a later phase characterised by trachytic lavas and dykes, rhyolite domes and lamprophyre dykes. Alteration consists of weak propylitic and argillic and, locally, intense advanced argillic, K-feldspar sericitic and silicic types. Marked trace-element depletions (Rb, Sr, Zn, Mn) are associated with K-feldspar-sericitic alteration and with advanced argillic alterations, whereas enrichments (Pb, Ag) are associated with K-feldspar-sericitic alteration. Gold distribution is highly localised and is controlled by breccia pipes and a caldera ring fault; it is not related to district scale alteration. In general, the geochemical and alteration patterns are complex, but they are clearly influenced by linear structures, the caldera ring fault and breccia pipes. Pipe-hosted Au-Ag and vein-hosted Ag mineralisation are associated, respectively, with early andesitic and late, post-caldera rhyolitic activity. The pipe-hosted and, especially, the vein-hosted mineralisation show affinities with adularia-sericite-type epithermal deposits

Jan 1, 1991

By L. Villa, O. Suarez, D. Arias, L. G. Corretge

The deposit comprises two vertical, lenticular bodies emplaced in the allochthonous block of a Variscan thrust. Epigenetic mineralisation occurs as replacement of carbonated volcaniclastic rocks of Cambro-Ordovician age. The dominant sulphide minerals are sphalerite and galena with minor chalcopyrite; the main non-metallic mineral is quartz and there is hydrothermal silicification, chloritisation and sericitisation. Sulphur isotope values for sphalerite and galena are heavy and reflect the fundamental relationship between delta-34S in ZnS and in PbS, suggesting isotopic equilibrium. Four sphalerite-galena pairs yield temperatures between 163 and 218 degrees C, in good agreement with the 187-207 degrees C estimated by the Ga/Ge-sphalerite geothermometer. The ore sulphide was leached by the hydrothermal solution from diagenetic pyrite in the host rocks and disseminated sphalerite and galena in Cambrian carbonates

Jun 19, 1905

By P. Golledge, A. D. S. Gillies

An investigation has been carried on samples of three Queensland coal dusts to determine the potential explosibility of dust-gas mixtures. The explosion potential of the samples was classified by the lean and rich limits of explosibility and the limiting oxygen concentrations for each sample. Plotting of these points showed 2-dimensional flammability limit surfaces for coal dust/oxygen, methane/oxygen and coal dust/methane mixtures. From these plots the 3-dimensional flammability envelopes defining the explosibility of the mixtures were defined. The explosion limits of the coal dust/methane/oxygen system were seen to be influenced most by the explosibility characteristics of coal dust. Methane exerted a stronger influence over the explosion limits when the coal had a low volatile content

Jun 19, 1905

By R. D. Dukimo, M. V. Sevian

The nature of fracture and factors that control the extent of fracture in the tumble-drum and drop-tower tests have been identified. The product-size distribution, on which the standard strength indices for these tests are based, and the breakage rate constants depend on a number of factors other than the strength of the lumps. The standard indices and rate constants are meaningful only in a comparative context and for events whose loading mechanism is similar. The results of experiments on three Australian ores, from Yandi, Koolan and Mount Whaleback, are used in combination with fracture mechanics theory to explain why different tumble-drum standards have been found to be fully consistent. A more meaningful measure of strength could be the parameters of the Weibull function, scatter and average strength

Jun 19, 1905

By L. E. Mordberg, E. N. Nesterova

Geochemical studies of the bauxite deposits show that the primary composition is gibbsitic. Some trace elements were relatively mobile during bauxite formation with the content of Th, U and Zr increasing and that of Rb, Ni and Co decreasing. Y and Pb were relatively immobile during lateritisation; their contents and ratios were inherited from different types of underlying rocks. The supply of Ni and Co took place at the diagenetic or epigenetic stages; their ultimate source was the crystalline basement in the region. The studies support the view that the bauxite was likely to have originated as a result of in-situ lateritisation and not through sedimentary transport and redeposition

Jun 18, 1905

By B. J. Breen, C. S. Mogg

Considerable borehole investigation work has been completed at a proposed site at Sellafield in Cumbria, supplemented by seismic surveys, other geophysical sensing and geological mapping. The focussing of investigation on the rock mass itself will be achieved by means of the planned underground rock characterisation facility, giving access to depths of about 800 m in the strong, low-permeability basement rocks of the Borrowdale Volcanic Group. Characterisation work undertaken during the sinking phase and interaction with continuing surface-based exploration and monitoring should permit a firmer assessment of the long-term safety of a repository. Key considerations in the choice of a design for the repository include the waste handling method, underground inlet cell, underground vaults, vault environment and environmental effects

Aug 1, 1994

By J. A. Finch, Zhenghe Xu, Z. A. Zhou

Whether the microscopic bubbles generated by the high energy dissipation and high feed-slurry velocities in new flotation cells are stable in solution and what roles they play in particle collection are of great interest for the flotation of fines. Experimental work has shown that, with fast flow of liquid through an orifice, stable microscopic bubbles can form in flotation systems by hydrodynamic cavitation in the absence of gas supersaturation. The minimum flow rate at which bubble formation is initiated varies from 8 to 15 m/s, depending on the design of the cavitation tube, which is within the range of feed slurry velocities of some newly developed cells. Feed aeration enhances the formation of micro-bubbles by hydrodynamic cavitation. The study suggests that the fast flotation kinetics of some new cells may be attributed in some degree to the formation of microscopic bubbles

Jun 21, 1905

By J Parnell, B Manson

Bitumen occurs in the basins in reservoir sandstones, in veinlets close to hydrocarbon source rocks, in veins through lava beds and in sulphide-mineralised veins where it is closely associated with, but predates, the sulphides. The role of organic matter was probably in enhancing metal reduction by creating a low-Eh environment rather than in metal transport. Coeval euhedral quartz crystals or albite in sulphide-bearing carbonate veins provide evidence of an aqueous component to the hydrocarbon fluid

Aug 1, 1995

By D. K. Bose, R. H. Rakhasia, V. D. Shah, J. C. Sehra

A series of experiments was conducted to determine the effects of roasting temperature, soaking period and quantity of soda ash added. At a laboratory scale, under optimum conditions of roasting at 873 K for 2 700 s with soda ash 10 wt% in excess of stoichiometric, molybdenum recovery was 99%. The investigations indicate the technical feasibility of producing high-purity MoO3 by combining the roasting process with carbon adsorption/desorption. The process uses low-cost chemicals, can be scaled up readily and is free of the SO2 pollution generated by conventional roasting, as the sulphur content of the concentrate is converted to sodium sulphate

Jun 18, 1905

By R. D. Stewart

Paper presented at the conference: Risk assessment in the extractive industries, held in Exeter, UK, 23-24 March 1994, and first published London: IMM, 1994, preprint volume, 18pp., 5 refs. A seismic risk assessment method has been developed for application to rockburst prone deep-level mining sites which have sufficient seismic coverage. The technique utilises several seismic hazard parameters simultaneously and assesses the seismic risk on a daily basis according to the individual levels of these parameters. Critical levels are determined from investigation of the long-term behaviour of the parameters in relation to recorded potentially damaging seismic events. The method has been applied to a data set comprising 15 months' worth of seismic data, with encouraging results

Aug 1, 1995

By G. X. Wang, R. E. Siemens, M. C. Fuerstenau, D. Chandra

Soda roasting of concentrates from Mouat, Montana, was performed in a temperature range of 450 to 650 degrees C and chromium was solubilised by water leaching at room temperature. It was found that high extraction yields of chromium were primarily dependent on the conversion of Cr3+ to Cr6+ during the roasting step, and this was enhanced significantly by simple attrition of chromite particles during this step. Gangue impurities (mainly Si) were more detrimental to Cr extraction than lattice impurities such as Al or Mg. It appears that oxidation proceeds into grains along a preferred crystallographic plane in the cubic lattice of the chromite. The effects of roasting time, temperature, soda to chromite ratio and particle size on the extraction of chromium are presented

Jun 18, 1905

By K. D. Russ, A. J. Beer

Non-contact systems for measuring underground voids have used theodolites, reflective or non-reflective laser methods and sonar techniques. An effective but cheaper alternative is based on use of a Wild T1000 electronic theodolite coupled to a Leica Data DISTO and a Wild GRE3 data logger. The software used to process the theodolite data is a spreadsheet and macro combination, while Surpac, Datamine and AutoCAD modelling packages have been investigated for viewing the tunnel profiles. The main limitations were found to be blinding, when irregularities in the stope obstructed the line of sight, and the 30 m range of the Data DISTO model used in the study, although more powerful models are available. All three modelling packages proved suitable, with Surpac providing the best-quality printed images of the voids surveyed and AutoCad by far the cheapest alternative

Jun 21, 1905