Search Documents

By A. Norori-McCormac

"Air recovery, the fraction of air entering a flotation cell that overflows the cell lip, is linked to flotation performance, and it has been shown through industrial testwork that operating flotation cells at air rates that yield the Peak Air Recovery (PAR) results in high mineral recovery. For operating parameters over which flotation plants have little control, such as particle size, investigating the effect on the position of PAR, and the subsequent effect on flotation performance, proves more challenging. To this end, we have developed a bench scale flotation system that runs continuously and exhibits froth behavior similar to that found industrially, allowing the study of such parameters as particle size in addition to air rate. The bench scale system comprises a 4 l baffled cylindrical flotation cell, stirred by a Rushton impeller. The concentrate is recycled back into the pulp, allowing for continuous operation. Glass beads are used as solid particles, allowing a wide range of particle sizes to be tested, with TTAB as collector and MIBC as frother. The system allows operation at air rates typical of industrial flotation systems (1 -2 cms-1 superficial gas velocity), in addition to yielding a froth that coalesces and bursts and exhibits a peak in air recovery as cell air rate in increased. Solids and water recovery is also measured. The results show that air recovery is sensitive to changes in particle size. The intermediate size distribution showed a peak in air recovery (PAR) that corresponded with the maximum solids flowrate, as found industrially. It is shown that finer particles do result in more stable froths and higher recoveries, particularly at low air rates. The effect of particle size on the position of PAR is not yet unequivocally determined from these results."

Jan 1, 2014

By Andrzej Wieniewski, Cezary Regula, Bozena Skorupska, Krystian Cichy

"In this paper, experiences from Polish non-ferrous metals ores enrichment plants in the copper and blende concentrates quality improvement are discussed. The blende concentrate being produced in ZGH Boleslaw S.A., with Zn content of about 54,5% is characterized by the relatively high magnesium content reaching a level of 1% resulting from the dolomite presence, while for the zinc production by electrowinning a concentrate in which magnesium content should not exceed 0,3% is required. The implemented new technology for the quality improvement of blende concentrate is based on the leaching of zinc concentrate with sulfuric acid aimed at dissolving of the contained dolomite, and then flotation of the leached concentrate. It allows to obtain a concentrate with magnesium content below 0,1% at the simultaneously increased zinc content to about 57,5%. In the paper, laboratory tests results on the development of optimal flotation flowsheet for the gypsum removal and the industrial tests results concerning the process optimization of this flotation are discussed. In turn, the copper concentrate being produced in Polish copper ore enrichment plants KGHM PM S.A., is characterized by the increased organic carbon content - above 8%. It creates problems with the smelting of this concentrate because of difficulties with the heat removal derived from the combustion of organic carbon in the flash smelting process. The implementation of segregating flotation to the industrial practice allows the effective production of two concentrates with the differentiated chemical compositions - a concentrate with increased copper content and reduced organic carbon content for the flash smelting process, and a concentrate with lower copper content and increased organic carbon content for the shaft smelting process. In the paper, conditions of the segregating flotation and the achieved results are described."

Jan 1, 2014

By Y. B. Zhu

Soil reconstruction and improvement trials and vegetation experiment is carried out at Shuilong-shan acid rock waste dumps at Dexing Copper Mine in China. pH value, Cu2+, Pb2+, Zn2+, etc. concentration in acid rock drainage (ARD) is also monitored every month since 2005. The results of experiment show that: Lime and topsoil stripped from open-pit is appropriated soil improvement material. Full cover soil improvement method is suitable for flat area, contour soil improvement method and hole soil improvement method is appropriate for slope area. The optimal plant species is ligustrum lucidum Ait,Lespedeza bicolor, Paspalum notatum, Veti-veria zizanioides, Eragrostis pilos and Neyraudia reynaudian. It is the best for Arbor, shrub and grass to be arranged in pairs or groups in order to remold optimal landscape. Pilot sites, covering 3ha, is established. Vegetation coverage reaches 90% in platform area, 40% in slope area. pH value in ARD increased slightly, Cu2+, Pb2+ concentration in ARD decreased, Zn2+ concentration in ARD decreased and varied slightly.

Jan 1, 2014

By V. F. Bannikov, A. P. Kozlov

"The purpose of this study was to develop a theoretical and technology framework for designing new combined technologies for processing tailings containing non-ferrous and noble metals using dry separation. The main goals of the study were: identifying the distribution patterns of valuable components in various fractions in dry separation processes; examining the patterns identified for different types of non-ferrous and noble metal tailings; developing a theoretical and technology foundation for the development of innovative technologies for the efficient processing of tailings with minimal process water consumption. To examine the possibility of efficient recovery of valuable components from refractory tailings using dry separation, an experimental laboratory unit was designed and built, composed of novel or modified lab equipment: plasma unit for increasing the magnetic susceptibility of Fe - containing minerals; magnetic separator supporting isodynamic and polygradient fields; pneumatic separator for the dry separation of finely dispersed mineral mixtures; dielectric separator using the resonant frequency of the electric field. The laboratory unit supports various modifications and combinations of the lab equipment. The experimental studies led to the development of a unified process scheme for lab tests of mature and non-ferrous smelter tailings using dry separation methods.INTRODUCTION The huge amount of waste from mining and processing of mineral resources Russia inherited from the extensive use of mineral resources in the Soviet Union and amount of waste continue to grow. Often the content of valuable non - ferrous, rare and noble metals in waste exceeds the balance contents in natural ores of the developed deposits. The availability of a rich scientific reserve for the creation highly effective innovative technologies for waste processing determines the necessity of the acceleration in the resolution of problems of the complex assessment, capitalization and involvement in the processing of technogenic resources in Russia (Chanturiya and Kozlov, 2014.)."

Jan 1, 2018

By J. Yianatos

The regrinding stage is necessary to achieve the particle size (liberation) for the final upgrade in the cleaning flotation process. At present, vertical mills (Vertimill) are employed at industrial scale, using small steel balls as grinding media. The regrinding process characterization requires mixing regime knowledge along with the mean residence time of the liquid and solid phases. The residence time distribution (RTD) and the actual mean residence time estimations from theoretical relationships are complex due to the presence of three components (solid mineral, balls and water), mass transport characteristics and segregation affecting solid holdup. Therefore, the experimental RTD determination is suitable for industrial mills. In this work, RTD measurements were performed in two different industrial flotation plants. Both plants operate with Vertimills of 1000-1500 HP in the regrinding process with different circuit arrangements according to the plant treatment capacity. The RTD was measured using the radioactive tracer technique. This technique allows for non-invasive tracer detection where the procedure consists of selecting a liquid (Br82 in aqueous solution) or solid (irradiated solid) tracer for RTD data acquisition in real time. The RTD was modelled by the Large and Small Tanks in Series (LSTS) model, which allowed the characterization of the different mixing regimes for both liquid and solids in the regrinding mills. Effective mean residence times in the range 2-11 min were obtained with RTD shapes similar to those obtained in tumbling ball mills. It was found that residence times of liquid and fine particles were similar, which is consistent with results observed in other mixing systems, e.g. mechanical flotation cells. Also, the mean residence times estimated from the RTD allowed the mass balance adjustment to be validated from metallurgical sampling data. RTD estimations are useful for better understanding the Vertimill behaviour and to identify the actual breakage rates. Keywords: vertical mill, residence time distribution, particle size, modeling

Sep 1, 2012

By Tiago de Souza, Caroline Gonçalves, Carlos Eduardo de Castro, Everton Dias

The Miraí plant from Votorantim Metais, has two screening stages to the bauxite classification after scrubbagem. The final product has hold the larger size of 0,84 millimeters (20 mesh). There are two sieves Haver & Boecker (model R-TE 3658 x 10972), which have four modules with cut size sieves of 10 mesh (1.70 millimeters) and ¼ inch (6.35 millimeters) on the primary screen, and 20 mesh (0.84 mm) on the secondary screen, all made of polyurethane. The actual configuration was established according to the empirical tests realized that aimed the increase material load on the secondary screening. However, having in mind the screening process improvement and use the fractions smaller than 0,84 mm, which have significant levels of Alumina and low reactive silica, was proposed a new test of change the sieves opening for 6 mesh in the primary screen and 28 mesh for the secondary sieve. The objective of this work was measure the ore alterations on the particle size distribution on the screening steps, increasing the plant weight and ratio recovery before and after the test.

Jan 1, 2014

By A. Vidyadhar

Printed circuit boards (PCBs) constitute a majorpart of electrical and electronic equipment containing valuable metals such as Cu, Ni, Au, Ag, Pd, Fe, Sn, Pb, etc. The concentration of base and precious metals in PCBs is observed to be several times more than those in their respective ores. Therefore, the recycling of PCBs is necessary to recover the valuable materials. However, the ultrafine particles pose a big challenge. Removal of them is suggested prior to processing by flotation. Froth flotation is observed to be a promising technique for rejecting the plastics from the comminution product. In the present work, enrichment of ground 1.0 mm PCB powder was investigated through flotation route by varying the operating variables such as frother dosage, pulp density, air flow rate and rotational speed of the impeller. The liberation studies indicate that excellent liberation of metal values is achieved from the non-metallic constituents at -1.0 mm size and below. The particulate system is quite rich in metal value with about 23% total metal content. The non-metallic constituents such as plastics are observed to possess strong hydrophobicity while the metal particles in the pulverized mass are hydrophilic in nature. Froth flotation kinetics is studied in depth with a view to facilitate high rejection of plastics and identify optimum operating conditions for the same. A number of experiments are performed to establish the influence of the operating variables on flotation performance. The conditions for achieving higher yield of the metal-rich fraction with respect to a specified grade are discussed in the light of the experimental results. It is found that the requirement of reagents is negligible which could be a very important factor from the commercial stand point. Single-stage flotation increases the metal content from 23% to over 32% with a mass yield of around 75% and over 90% recovery of metal values. 32% of the materials in the feed could be effectively rejected in the float fraction losing less than 4% metal values. The dependence of kinetics on the process variables is also discussed. It was concluded that a high rotor speed helps in efficiently rejecting the plastics. Frother should be added to help stabilize the froth and enhance the kinetics. A moderate air flow is required while pulp density must be kept low for efficient pre-concentration. It is established that the entire -1.0 mm comminution product could be treated by flotation for generating a pre-concentrate. Keywords: printed circuit boards, recycling, froth flotation, kinetics, recovery

Sep 1, 2012

By S. M. Narbekova, L. V. Semushkina, Zh. A. Aldybayeva, A. A. Mukhanova, D. K. Turysbekov, N. K. Tussupbayev

More complex and heavy-concentrating oxidized and mixed sulphidic oxidized ores are involved in production because of increasing needs for non-ferrous metals. Extraction of the oxidized minerals of non-ferrous metals general in current technologies. The problem is solved to oxidized polymetallic ores the preliminary selective sulphidization is the oxidized surface of the components by means of hydrogen sulphide, sulphide and calcium polysulphide, and also element sulphur, etc. The task was to study details of flotation of the oxidized lead-bearing ore of the Zarechnoe deposit (Kazakhstan) with calcium polysulphide as sulphidation. According to chemical analysis initial samples of the ore contain, %: lead – 4.8; zinc – 0.1; general iron – 0.81. Phase structure lead is characterized by the oxidized form of 57.76-64.5 %; by sulphidic status of 25.5-32.64 %, and by plyumboyarosite of 19.0-23.02 %. Researches on flotation beneficiation of oxidized lead-bearing ore are conducted. Sulfidizator gave to grinding, on flotations there were used the collector (butyl xanthogenate of sodium) and frother (T-80). Experiments were conducted with a new sulphidizator – calcium polysulphide. The latter is obtained by interaction of CaO calcium oxide with sulfur and water at high temperature with component mass the following ratio S:CaO:H2O =10:5:85. Extent of mill initial ore was optimised (88.42 % of - 0.071 mm grade). For the optimum mill mode the studies on matching of an optimized consumption of sulphidizators are performed. On basic technology with application of sulphide of sodium as a sulphidizator at optimum mill, the lead concentrate with the content of lead 64.4 % at extraction of 86.6 % was received. The content of cerussite in a concentrate was about 14.9 % at extraction of 82.1 %. With application of calcium polysulphide as a sulphidizator the lead concentrate with the content of lead 68.0 % at extraction of 88.0 % was received. The content of cerussite has made 16.0 % at extraction of 85.0 %. Application of a new sulphidizator allows to increase extraction of lead in a concentrate from 64.4% to 68% and cerussite extraction – from 82.1 % to 85.0 %. The possibility of application of calcium polysulphide as a sulphidizator instead of conventional sulphurous sodium was established.

Jan 1, 2018

By A. Javadi

"Our recent studies revealed that the sulfide minerals in contact with water during grinding produced hydrogen peroxide (H2O2) where the amount of H2O2 production by the minerals found to be in the order of pyrite > chalcopyrite > sphalerite > galena. The H2O2 effect on the oxidation of pulp components and its influence on the concentrate grade and recovery in flotation have been studied and the results have been presented and discussed in this paper. Studies have also been carried out to build correlation between percentage of pyrite in the concentrate, grinding conditions and concentration of OH•/H2O2 in the pulp and as well of controlling the formation of these species through known chemical means for depressing the generation of the oxidant. Flotation tests using a complex sulfide ore with the same reagent scheme that is being used at Bama concentrator in Iran but with the addition i) Na2S reductant and ii) inorganic (EDTA) and organic (TETA) surface modifiers, during grinding stage have been performed to judge the beneficial or detrimental role of H2O2 on the selective flotation of sulfides. The results demonstrate that the selectivity of metal sulfides against pyrite increases with increasing generation of H2O2 in the pulp liquid.INTRODUCTIONOur recent studies have illustrated the formation of hydrogen peroxide (H2O2) by metal-sulphides during grinding in the presence and absence of oxygen (Javadi Nooshabadi & Hanumantha Rao, 2013a; Javadi Nooshabadi & Hanumantha Rao, 2013b; Javadi Nooshabadi & Hanumantha Rao, 2013c; Javadi Nooshabadi & Hanumantha Rao, 2014). In the absence of oxygen, it was found that pyrite surface is catalytically active and able to breakdown water molecules to form OH• free radical and thereby deriving oxygen in the formation of H2O2 from water molecules. The in-situ formation of H2O2 and its influence on sulphide flotation has not been addressed yet. The presence of strong H2O2 oxidant in the pulp liquid and its selective oxidation of pyrite would be beneficial in depressing pyrite flotation. Therefore, it is important to build correlation between percentage of pyrite in the concentrate, grinding conditions and concentration of OH•/H2O2 in the pulp as well as to study possible ways of flexibly controlling the formation of these species through known chemical means for depressing the generation of the oxidant."

Jan 1, 2018

By M. Blagojev, R. Tomanec

"Studies reported in this paper used polymetallic Pb-Zn-Sb-As-(Ag, Au) ore from Dražnja, Kosovo. The ore is comparatively rich in Zn (6.56%) and Pb (2.87%), but with high rates of Sb and As. Conventional lead and zinc concentration by flotation produced galena and sphalerite rich concentrate with high recovery, but with excessive As and Sb. After chemical analyses, which could not detect the reason for the excessive elements, ore minerals were identified under the ore microscope, their texture characterized, and degree of liberation of useful minerals was assessed. Microscopy of the mineral concentrates revealed complex intergrowths of galena and marmatite minerals mostly with sulphosalt minerals (boulangerite, jamesonite and bournonite) and also with arsenopyrite mainly responsible for the unsatisfactory quality of the concentrate. These complex sulphosalts, among other things have similar behaviour during the flotation concentration, and in spite of their interlocking with galena, therefore inadequate liberation, sulphosalts remain in the lead concentrate. Microscopic analyses indicated that a better galena concentration product is possible with a higher rate of mineral liberation, and then by selective floc flotation of some sulphosalt minerals. Purpose of this work was to show that only chemical analysis is not sufficient, according to that we solved the problem by precise mineral identification and time consuming mineral liberation measurements. INTRODUCTION The polymetallic Pb-Zn-Sb-As-(Ag, Au) ore body of Dražnja, Kosovo, fairly rich in Zn (6.56%) and Pb (2.87%) was repeatedly explored and once even worked. Mineralization at Draznja was primarily represented by sphalerite, galenite and marcasite/pirite. Some sections comprise massive sulphides, and others are lower grade zones of semi-massive sphalerite/galena or marcasite/pyrite dominant sulphides. The ore body II was formed in the southern gallery in the structure Çukë – Lajthishtë (with content of 3.16% Pb and 7.31% Zn). Pb-Zn ore with increased content of As, Sb sulphosalts is not rare phenomenon in the world. While previously treated as unprofitable, economical uninteresting ore, today with development processing and new reagents (organic, ecologic), are the topic of scientific papers. The examination of Pb-Zn ore with high content of sulphosalts we find in deposits as: The hydrothermal vein deposit of Harja in the Baia Mare area, contain a wide variety of sulphosalts [Cook, N. & Damian, G., 1997]; also the deposits Fankou Mine in Guangdong Province and the Dachang Mine in Guangxi Province, where the flotation concentration of galena and jamesonite takes place [Runqing Liu et al. 2015], [Zhang Ting, Qin Wen-Qing, 2015];. On a samples from Tibet in China flotation separation test of galena and jamesonite was conducted [Sun Wei, Han Haisheng, Tao Hongbiao, Liu Runqing, 2015]. According to history of investigation, the mineralized area of Dražnja has a long history of exploration and possible exploitation activities [Slowey, Galen, 2009]. Recent workings were carried out in three stages through the 20th century."

Jan 1, 2018

By M. Barsky, E. Barsky

It is generally accepted that the optimal flow velocity for gravity classification is the final particle settling velocity or, which is the same, the particle spin velocity. However, we have found differences between the settling velocities and the spin velocities of the very same particles. Here we present the results of experiments in a cascading gravitational classifier comprising eleven stages. The feed material was introduced at each stage successively, from the first to the eleventh. The optimal flow velocity was determined for each case. From these experiments it follows that the value of the optimal flow velocity depends to a greater extent on the point of introduction of the feed (i.e., on the design of the device) than it does on the interaction between the solid phase and the flow.

Jan 1, 2003

By X. S. Yuan

With a demand for increasing energy efficiency and a need for improving bitumen recovery, a highly integrated solution for sustainable lease development of Aurora North of Syncrude has been proposed and implementation plans are underway. Flocculation and thickening technology as an important component of the integrated solution provides Syncrude an opportunity of rapid heat recovery from tailings and more flexible tailings closure and reclamation options. Flocculation of fine-particle suspensions by polymers is a non-equilibrium process whose performance is strongly influenced by physical and chemical variables. While polymeric flocculants are frequently used to establish the chemical conditions favorable for flocculation, the actual performance of a flocculation process generally depends more on the physical variables, such as the hydrodynamic conditions in mixing the flocculants and slurry. In order to study the effect of hydrodynamic conditions on flocculation of Syncrude fine tailings, a standardized laboratory test procedure called power flocculation has been developed in comparison with the conventional manual mixing methods. It is shown that the agitation speed and time in conditioning the flocculant solution and the slurry have a profound effect on the flocculation performances measured by initial settling rates, supernatant clarity and sediment density. It was found that the optimum bench test conditions for power flocculation of Aurora fine tailings with a sand-to-fine ratio (SFR) of about 1:1 are conditioning of the flocculant solution and the tailings slurry at 250 rev/min to 300 rev/min in 20 s to 40 s. The test results are inter-preted with a flocculant adsorption/redistribution kinetic model that helps understanding of the effect of hydrodynamic conditions on flocculant adsorption, floc formation and floc growth.

Jan 1, 2014

By Zhiyong Gao, Ruiying Fan

"Crushing and grinding are the prerequisite processes in many industries, such as minerals processing and powder technology. During crushing and grinding, minerals will cleave or fracture along the directions by broken the interlayer bonds (e.g., ionic bonds), generating some commonly exposed surfaces. The broken (or dangling) bonds at the generated surface makes the surface more active and determine the reactivity of the surface. In this work, the population of broken (or dangling) bonds on commonly exposed surfaces of fluorite mineral (a chosen model mineral) was calculated. Based on the calculated broken bonds information, the anisotropic surface reactivity of fluorite such as surface energy, surface relaxation, dissolution, wettability, surface charge and adsorbability, were discussed. The results show that the surface broken bonds density, which is positively related to the surface energy, can be used to predict the cleavage nature, surface relaxation degree and surface stability of fluorite crystal. The distribution characteristic and the number of broken (or unsaturated) bonds of surface active atoms (like Ca for fluorite crystal) can be used to predict and explain the anisotropic wettability, surface charge and adsorption mode and strength of organic molecules on different commonly exposed surfaces. It is easy to conclude that the calculation of surface broken bonds can serve as a fast and accurate way to start the mineral chemistry studies. These findings will be helpful to the mineral/material chemistry research in related interfacial science communities.INTRODUCTIONGrinding for mineral liberation is a prerequisite for a successful flotation separation. Also grinding for size reduction is a prior process for a favorable powder technology. During the grinding process, the minerals / materials will cleave and fracture along certain crystal directions with relatively weak interlayer chemical bonds1 to form a number of common exposed surfaces. Exposed surfaces are the outer boundary of a solid substance. In the mineral / material block, the bonding orbital of the atoms is filled with electrons and the atoms are in a steady state. Atoms on these exposed surfaces appear to show dangling bonds (or broken bonds) by losing chemical bonds to adjacent atoms in the previous block. Therefore, surface broken bonds serves as an initial property of a fresh surface. The lattice arrangement and crystal orientations causes differences in the number of dangling bonds on each exposed surface, i.e., anisotropic surface broken bonds2. The anisotropic dangling bonds enable the exposed surfaces to show varying degrees of surface reactivity (including surface energy, surface charge, surface relaxation, dissolution, wettability and adsorption behavior), known as anisotropic surface reactivity."

Jan 1, 2018

By F. K. Ikumapayi

An approach to environmental sustainability and improved process economy, in sulphide minerals production is recycling of process water in flotation of complex sulphide ores, although the chemistry of process water may be a critical issue to flotation efficiency. The influence of major components of calcium and sulphate ions in process water on xanthate collector adsorption and flotation response using pure chalcopyrite, galena and sphalerite minerals were investigated by Hallimond flotation, zeta-potential measurement, FTIR and XPS spectroscopy studies, while bench scale flotation tests were also carried out using complex sulphide ores. The impact of the species in flotation was comprehended using deionised water, tap water, process water and simulated water containing equivalent amount of calcium and sulphate species in process water. Hallimond flotation results showed a decrease of chalcopyrite and galena recovery in process water and also in the presence of calcium and sulphate ions in both deionised and process waters, whereas sphalerite does not respond to flotation. The adsorption of calcium and metal ions but not sulphate ions on the minerals is evidenced by zeta-potential data. FTIR and XPS studies revealed the presence of surface oxidized sulfoxy species and surface calcium carbonates on chalcopyrite in the presence of process water and water containing calcium ions, surface oxidized sulfoxy and carbonate species on galena in the presence of deionised water, process water and water containing calcium and sulphate ions, all at flotation pH 10.5, and these surface species influenced xanthate adsorption. The presence of surface oxidized sulfoxy and carbonate species at the sphalerite flotation pH 11.5 were seen in the presence of deionised water, process water and water containing calcium and sulphate ions, but the surface species does not influence xanthate adsorption. Bench scale flotation using two different complex sulphide ores showed that chalcopyrite, galena and sphalerite recoveries are better in process water than tap water. The studies showed that the process water can be recycled in flotation with no detrimental effect on grade and recovery of sulphide minerals. Keywords: sulphide minerals, flotation, zeta-potential, FTIR, XPS

Sep 1, 2012

By A. V. Faiberg

Currently, the interest to conditioning of cyanide-bearing recycled solutions with high-grade of base metals, in particular, copper has significantly grown. This can be explained by two major factors. Firstly, there are strict regulations on cyanides amount in tails and higher cost of detoxification processes. This problem can be easily solved during the ore treatment using the conditioning of solutions and water recycling. Secondly, the presence of other metals minerals which react with cyanide during gold leaching resulting in high cyanide consumption. The presence of copper is a major problem. Many copper minerals react with cyanide with the formation of cyanide complexes-Cu(CN)2-, Cu(CN)32- and Cu(CN)43-. One mole of copper consumes 2-4 moles of free cyanide. Availability of cyanide-soluble copper minerals has deleterious effect on gold leaching (gold recovery, cyanide consumption, tails detoxification, efficiency of gold elution and electrowinning). The precipitation of copper from the solutions improves gold recovery by CIL. The removal and recycling of cyanide allowed the reduction of cyanide addition to the process. The recycling of spent cyanide-bearing solutions based on the removal of copper and the return of cyanide bound in complex compounds for leaching process is an optimal way of solving the problem of gold-bearing copper ores treatment. By using the technology, an adverse impact onto gold recovery process is eliminated and at the same time reducing the cyanide consumption. Today, processes and methods of high-grade copper leaching solutions conditioning before and after gold recovery have been developed, which combine two ways of copper recovery: as a saleable product and cyanide to recover gold and reduce total operating costs. They are Cutech, MNR, SART, Cyanomet, AuGment, Vitrokele, Hannah and Cyanisorb. At the same time, these technologies have not been studied enough and described in literature. Data on parameters and operating conditions as well as introduction is not available. The conditioning technology of recycled solutions developed by IRGIREDMET JSC allows copper to be recovered as high quality concentrate and at the same time free cyanide regeneration in the recycled solution which is amenable to gold leaching. This technology was commercialized at a mine in Kazakhstan in 2008. The removal and recycling of cyanide does not require additional cyanide and is cost-effective. More cost-efficiency is achievable through selling copper concentrates, closed water cycle without the detoxification of effluents and enhanced gold recovery by CIL and cathode quality.

Sep 1, 2012

By T. Khonthu

The purpose of this investigation was to evaluate the relationship between different milling procedures, viz. a ball mill and an IsaMill respectively, and the flotation performance of the different mill products. Two ores were used, viz. a base metal sulphide (BMS) and a platinum group mineral (PGM) UG2 ore. Flotation was used as a diagnostic to investigate whether the different milling procedures may have different effects of the floatability of the particles. The present study is part of a research programme investigating this question using a wide range of comminutiondevices and procedures. Similar particle size fractions from the different milling procedures were used in the flotation tests. The particles were characterized in terms of particle size distribution, morphology (using scanning electron microscopy and image analysis software) and rheology tests. The results have shown that in general when comparing similar feeds to flotation in terms of equivalent particle size distributions as indicated by the d80 value, the ball mill generally yielded better recoveries and grades in the case of the BMS and lower chromite recoveries in the case of the UG2 ore compared to the IsaMill. No significant differences were observed in the morphological or rheological characteristics of the particles subjected to the different milling procedures. Although the results appear to indicate that IsaMilling is less advantageous than ball milling in terms of the flotation performance for the two ores studied it should be emphasized that these results do not take into account the relative advantage which IsaMilling has over ball milling in terms of direct and indirect energy consumption and GHG emissions nor, most importantly, does it consider the platinum group element recoveries in the case of the UG2 which may have increased significantly as a result of the finer grind which the IsaMill produces after 4 passes compared to the ball mill after 64 min. Such results which will be reported is due course may show that the greater liberation expected after IsaMilling of the PGMs outweighs any disadvantages indicated in this study.

Sep 1, 2012

By S. J. Neethling

"This paper examines the impact of several key variables on the performance of flotation cells. The study makes use of a simulator for the froth phase of the flotation vessel, as the main purpose of this study is to separate the impact of different variables from one another. In experiments it is very difficult to separate the effect of variables from one another as a change in a singe input parameter, such as air rate, invariably also affects many of the other key variables, such as bubble size and bubble bursting rates.In order to achieve this a base case simulation that is typical of many of the rougher cells found in sulphide flotation circuits was carried out. Four key variables, air rate, incoming bubble size, surface bubble size and the fraction of the bubbles flowing out of the cell unburst, were varied in order to obtain the system.s response.The most significant results were obtained when the bubble size was varied. An increase in the incoming bubble size has the effect of reducing the pulp zone recovery, but increases the froth zone recovery. If it were possible to vary the incoming bubble size without influencing the overflowing bubble size, the impact of the change would be unclear because of these two competing effects. The effect of a change in the overflowing bubble size has an opposite effect on the froth recovery, with larger bubbles resulting in lower froth recoveries.A final interesting result is that all the effects examined affect the process to a similar degree, which implies that none of these variables can be disregarded, either in industry or in further research."

Jan 1, 2003

By C. A. Perez

Estimation of rock composition in mineral plants is important to determine rock size and grindability which in turn may improve control of the grinding process. Variations in ore grindability and size distribution directly affects mills power consumption and throughput. Therefore, it is desirable to develop new tools to estimate rock lithological composition. In this paper, a new method for lithological classification based on machine vision is proposed. The method is based on a single video camera and employs information about texture using several different spatial scales. Texture information is extracted from rock images using Gabor filters that can be adjusted at different spatial scales and orientations. After feature extraction, rock images are classified using support-vector machine (SVM). The method was tested on a database containing sub-images of 64x43 pixels of five ore types as follows: massive sulphide (MS), disseminated sulphide (DS), net textured (NT), gabbro (G), and peridotite (P). These ore types were assigned to three grindability classes: soft (MS), medium (DS and NT) and hard (G and P). The database was divided in 2 subsets for training, cross validation, and for test. Classification accuracy is compared with previously published results on a dataset with three different classes of rocks according to their hardness. Results show that our proposed method reached significant improvements (between 13%-20%) in classification accuracy relative to previously published results. Keywords: rock classification, lithological classification, grindability estimation, Gabor feature extraction, texture features

Sep 1, 2012

By P. Oliveira, A. Peres, A. Silva

"The decrease in iron content and increase in contaminants grade, associated with greater participation of compact and semi-compact materials, has impacted the recovery of a mechanical cells flotation circuit in the Iron Quadrangle, Brazil. The recovery decrease in the flotation stage motivated the current conventional flotation circuit reevaluation seeking alternatives to restore the recovery, without affecting the final concentrate quality parameters, with low investment. Sampling, chemical characterization of samples, bench scale flotation experiments, and mass balances were conducted. Analysis of the results showed opportunities to improve the circuit performance. The stages prior to the flotation circuit changes were: rougher, cleaner, recleaner and scavenger. In the previous configuration, recleaner was operated as cleaner scavenger and the iron grade in the scavenger concentrate was 23%, representing 38% of the new feed. After the circuit change, the circulating load was reduced from 38% to 15% and the iron content was upgraded to 42%, resulting in increased residence time. The iron content in the global tailings of the concentrator was decreased from 10.9% (year of 2013 average) to 10.2%, representing gains in both mass and metallurgical recoveries.INTRODUCTIONRegarding plant practice, the year 1972 represents a landmark for the concentration of iron ores in Brazil. VALE started up 28 units of WHIMS (wet high intensity magnetic separators) at the Cauê plant in Itabira, each one producing 1x106 t/year of concentrate. Later 17 WHIMS machines were commissioned at Conceição. During the 80’s decade of last century, changes in the ROM required the addition of a cleaner flotation stage to decrease the silica content in the pellet feed.The first company to use reverse cationic flotation as the only concentration operation of iron ore was SAMARCO (start up in 1977). Since 2015 flotation has been utilized at VALE in Itabira as major concentration process, magnetic separation acting as scavenger stage.The Jones matrix type WHIMS were manufactured for decades under patent by KHD Humboldt Wedag. After the expiration of the Jones patent, Eriez Magnetics took the world leadership regarding WHIMS manufacturing. The Brazilian branch of Eriez is Inbras. Based on plant practice experience at the Fabrica concentrator, the Brazilian company Gaustec was established (RIBEIRO and RIBEIRO, 2010) and is now present in different countries. The mega sized WHIMS GHX-1400 (18.000 Gauss, gaps smaller than 1.5 mm) were developed to face the challenge of huge throughput required by iron ore processing (Ribeiro et al, 2017)."

Jan 1, 2018

By M. Eraydin

Dewatering fine particles (e.g., flotation concentrates) is inefficient, energy intensive and often requires large capital and operating costs. To address these issues, a series of advanced dewatering technologies have been developed at Virginia Tech. These include novel dewatering aids and a hyperbaric centrifuge. Typically, the moistures obtained using these methods are 30% to 50% lower than those obtained using conventional methods, as demonstrated in laboratory and pilot-scale test programs. With another novel dewatering technology that has been tested in bench-scale tests, the moistures can be reduced to levels once believed to be attainable only through the use of thermal dryers. In this communication, test results obtained with these advanced dewatering technologies are presented and compared.

Jan 1, 2014