Search Documents

By Robert F. Stevens, Robin Givet, Kenneth Viking

"Summary This paper describes a case of a directional pile installation conducted from an existing oil platform in the Caspian Sea, offshore Baku. Results are presented for 660 mm outer diameter (660 mm OD) conductor piles. Each conductor was equipped with a beveled aluminum toe for directional impact driving and was driven through a 710 mm casing using a Delmag 100–13 diesel hammer and a chaser pile. The 710 mm casings were preinstalled to a depth of 75 m below mud line (75 m BML). The longest impact driven conductor pile on the project was 456 m at end of drive, and reached the terminal depth of 295 m BML.Soil conditions consisted of soft to stiff silty clay to a depth of 30 m BML, underlain by stiff clay to 96 m BML, very stiff silty clay to 200 m BML, and very stiff to hard clay down to 300 m BML.In order to assess the maximum stresses in the conductors and check the performance of the hammer, the driving of each conductor was monitored using a Pile Driving Analyzer (PDA). The hammer fuel setting was adjusted based on the PDA outputs to ensure the conductors were not overstressed during installation. All driving and monitoring operations were carried out from the drill floor.The conductor piles drove easier than anticipated but in the direction predefined by the pre-cut angle of the beveled aluminum toe. The driving system performance was good. Post driving, the SRD were analyzed by either the global method analysis, using WEAP, or by the CAPWAP program.To detect any collision between the conductor being driven and the adjacent wells in production, the well heads were monitored in real time with high sensitivity accelerometers. These accelerometers were connected to an alarm system on the drill floor, triggering a siren and a strobe light should a collision be detected by an abnormal increase of the peak acceleration.IntroductionThe world longest directional impact driven pile was installed in year 2005. The operation was carried out from an offshore production, drilling, and quarters (PDQ) platform located about 120 km east of Baku, in the Caspian Sea.The platform foundation consists of driven piles and 24 slots were available for drilling the wells to the reservoir, located about 3800 m below sea floor. Each slot was fitted with a casing, 710 mm in diameter, running from the top of the jacket to a depth of about 75 m BML (Figure 1). Oil production started in 1997 and by the end of 2003, 14 wells were in operation; 10 slots were therefore still available, either for oil production or for water injection. However, due to larger than expected settlement of the platform, drilling of additional wells was put on hold. After further investigation, experts concluded the settlement was due to an alteration in the mechanical properties of the bearing strata supporting the foundation piles. This alteration was due to either excess soil material transportation, or soil fracture by the drilling fluids (mud), when drilling the first wells. With only 14 wells in production, out of 24 possible, the owner faced a new dilemma: to drill, or not to drill new wells?"

Jan 1, 2014

By Karen J. Dawson, Francisco Johnson

"Pressure-grouted high strength helical displacement piles are a recently developed pile type that can be useful in conditions where noise or vibrations must be low or where access or clearance is limited. However, there is no information in the literature that can be used to estimate the soil resistance of these piles or production rates. To fill this information need, this paper presents a New Jersey installation case history and the results of static axial and lateral load tests on both pressure-grouted and ungrouted high strength helical piles at the case history site and trial installation locations in New Jersey and Washington State. Piles between 25 and 50 feet long comprised of steel shaft diameters of 4.5, 5.5, and 7 inches with equivalent grout column diameters ranging from 12 to 22 inches were tested. Lateral loads of up to 100 kips and axial compression loads of up to 700 kips were applied. The results of the load tests are compared to predictions of lateral deformation and axial resistance.INTRODUCTIONHelical piles have long been recognized as a useful foundation type in situations where noise and vibrations must be limited, or where there are access or clearance restrictions. Relatively well-documented design methods and torque to capacity correlations have been developed for the most commonly used helical piles, which are relatively small (typically shafts of 6 inches or less) with corresponding low load carrying resistance.With the increased need to construct in congested urban environments, there is incentive to develop helical piles with higher axial resistance. Seismic and other loading conditions also require lateral resistance, which is low for the typically small helical pile shafts. One method of increasing the soil resistance, both axially and laterally and at relatively low cost, is to place grout around the shaft. Injecting the grout under pressure through the hollow helical pipe section and out a grout port or ports located near the toe of the pile has the potential to increase the pile resistance significantly above that which can be achieve by gravity grouting. Not only does the pressurized grout push out against the surrounding soil, but the rotating helix helps to distribute the grout laterally. Unfortunately, little information is available in the literature to help designers estimate the resistance of grouted helical piles in general and none is available regarding pressuregrouted helical piles."

Jan 1, 2016

By Alessandro Bertero, Stefano Valagussa, Filippo Maria, Wesley Schmutzler, Leoni

"Abstract The Deep Mixing Method (DMM) represents a viable solution to improve the adverse geotechnical properties of foundation soils. Differences and the importance of performing pre-construction laboratory and field tests will be highlighted. Comparative analyses and interpretations between the various lab and field stages, along with accumulated information about soil properties and QC results, allowed fine-tuning of the production parameters throughout almost the entire project.Two projects where the US Army Corps of Engineers selected the Deep Mixing Method (DMM) for the required stabilizations, and a third project completed in Italy, will be illustrated:•,?the LPV 111 Project (New Orleans - LA – USA); DMM was used for groundimprovement/foundation strengthening and consequently stabilize and support the burden of the new levee.•,the Rio Puerto Nuevo Project (San Juan - PR - USA); DMM was applied to improve the soils adjacent to a 90” forced sewer main relocation and to improve the soils for the base of a new drainage channel•,the new Italian high speed railway project (Florence Italy); DMM technology was applied to realize a a TBM break in/break out, foreseen originally by jet-grouting.IntroductionThe Deep Mixing Method (DMM) represents a viable solution to improve the adverse geotechnical properties of foundation soils. The effectiveness of working parameters depends largely on the physical and mechanical properties of the soil to be treated. Therefore, well designed laboratory and field test programs, aimed to disclose the interaction between the site-specific soils and the mixing parameters, are essential to achieve the desired end product."

Jan 1, 2014

By Ashirbad Satapathy, Sanket Rawat, Ramanand Shukla, Ravi Kant Mittal

Bearing capacity factor (Nq) and Adhesion factor (α) are the key parameters for analyzing the load carrying capacity of pile foundations embedded in cohesionless and cohesive soils respectively. Numerous models are available in the form of charts or equations for the computation of these parameters and hence, have been adopted by most of the International and National standards. Indian Standard for the Design and Construction of Concrete Pile Foundations, IS 2911–Part 1 (2010), also makes use of charts detailed in its Annexure B. However, the sources of these charts have not been specified clearly, making it difficult to back-refer to the actual models to assess their basis for resolving any critical scenarios encountered during design. The present study aims at acquiring a distinct understanding of the development of these charts in order to bring more clarity to the design process of pile foundations. The given charts have been compared with various models specified in existing literature and international standards for the calculation of Nq and α for both driven and bored piles and hence, the basis of Indian Standard charts has been identified. Moreover, it is evident that the use of these charts complicates the process of automation of analysis and design of pile foundations as well as the associated optimization studies. Additionally, the manual entry of data especially, from the logarithmic graph of Nq, escalates the chances of error thus, making it a critical concern for design offices. Therefore, this paper also presents a non-linear regression model for Nq and α, developed using NCSS software for both driven and bored piles. Through multiple iterations, the value of coefficient of determination for Nq and α has been found to reach greater than 0.995. The developed equations can be simplistically used for both manual and automated analysis of pile foundations.

Nov 1, 2022

By Karl A. Higgins

In August 2004, the long-awaited National Harbor project in the DC metro area sprang to life with the design of Gaylord National Resort and Convention Center. When the project was in its final stages of construction in 2007, it was noted as largest building development of the east Coast and the 4th largest Building project in the U.S. The final construction costs were above $900M and it served as the catalyst for the overall National Harbor development which added another $1B in construction costs over the next few years. The Gaylord Hotel is supported by approximately 150,000 linear-feet of driven precast concrete piling, one of a handful of major DC area projects in the early 2000s that were supported by this pile type. The project overall was a success, but the fast-paced construction schedule created significant challenges to the designers and contractors. Piling installation was the first major building construction task, and it did not start out well. While the test piles were installed without damage, when production pile driving began in the summer of 2005, pile head and body breakage soon became evident. Typical of most highprofile projects, there are many stakeholders involved and an equal number of opinions on why the piles were breaking. The financial and contractual implications of starting the project off awkwardly were evident to all. The pile driving criteria was scrutinized by the contractor, and the engineer’s had reservations about the size and type of the hammers used for pile driving. Ultimately, it was proven the leading cause of pile breakage was neither the pile driving criteria nor equipment, rather the pile materials themselves. The author of this paper is also the Geotechnical Engineer of Record for Gaylord National and many of the adjacent National Harbor buildings including the recently completed MGM casino. About 100 piles were damaged during Gaylord’s construction some requiring multiple piles for replacements. Over the past decade or so, rumors on the causes of the pile breakage have spread in the market, with some alleging this pile type is not compatible with the geologic setting. I have purposely avoided writing this case-study due to the controversy surrounding the subject, but now some 15 years later it seems appropriate to do so considering DFI’s annual conference location. This will be a fact-based assessment of pile breakage at Gaylord and will also include a comparison to the neighboring buildings where far fewer driven piles were damaged, once a more appropriate concrete mix design was required. The pre-cast supplier is no longer in business.

By Marco Fellin, Van E. Komurka

Significant cost and construction benefits were obtained from performing a bi-directional static load test prior to construction on the Russell Street Bridge Replacement project in Missoula, Montana. The project utilized 24 drilled shafts to support two three-span bridges across the Clark Fork River. A bi-directional static load test (“BDSLT”) was performed on a large-diameter production shaft to demonstrate construction methods and confirm design assumptions. Subsurface conditions consisted of gravel with sand to a depth of 20 feet (6.1 m), underlain by gravel with sand, silt, cobbles, and occasional boulders. The test shaft had a nominal diameter of 5.9 feet (1.8 m), and an embedded length of 75.5 feet (23.0 m). The geotechnical engineer of record and the BDSLT test engineer collaborated to optimize the BDSLT jack assembly location within the test shaft, determine appropriate instrumentation locations, and plan the test protocol. The maximum applied test load was 10,707 kips (47.6 kN). Significant benefits were obtained from performing the BDSLT test, including 1) reducing each production shaft’s length by using a higher LRFD resistance factor allowed by having performed the testing, 2) using test-determined unit shaft resistances to evaluate and accept two production shafts that may have otherwise required remediation, and 3) providing the Montana Department of Transportation (and other designers) with increased presumptive unit resistance values in the gravel/cobble/boulder deposits. PROJECT DESCRIPTION The project was constructed in Missoula, Montana for the Montana Department of Transportation (“MDT”). The original bridge was approximately 60 years old, and consisted of a two-lane, 420-foot-long (128-m), four-span, riveted steel plate girder design spanning the Clark Fork River. The bridge was due for replacement owing to its deteriorated state, and the need for increased traffic volume capability afforded by a four-lane structure. HDR was the structural engineer. The preferred bridge alternate was a 459-foot- long (140-m), three-span, welded steel plate girder design. The new bridge was designed to meet current standards in accordance with MDT bridge design and AASHTO LRFD criteria. The new bridge was constructed in phases to keep traffic open during construction.

Jan 1, 2019

By Y. M. Ha, T. D. Nguyen, D. T. Nguyen, H. K. Choi

Conventionally, cement deep mixing (CDM) columns are designed to have constant diameters over the improved depth as this facilitates the construction procedures. However, this design pattern may be inefficient in cases of spread footings or shallow foundations. This paper first briefly introduces principles of an improved CDM method that can create head-enlarged CDM (termed PF) columns. A simple analysis approach was introduced to obtain optimal shape of PF columns that results in minimum settlement. The effectiveness of this improved method over the conventional CDM method was then illustrated by settlement analysis for an actual footing in a case study using two recommended analytical methods in the literature. Analysis results from the case indicated that by using the same amount of soil-cement mixed volumes, settlement from a footing on PF columns can reduce up to 10 % compared with that from the same footing on CDM columns. In addition, a material quantity comparison for the case indicated that to have the same settlement values the volume of each PF column can be reduced of around 10% compared with that of the CDM column. INTRODUCTION The cement deep mixing (CDM) method is one of the most popular methods in ground improvement works. Details on the method such as construction procedures, necessary equipment and recommendations are described in many references or manuals (e.g. Bruce et al. 2013, BS EN 2015, Kitazume and Terashi 2013). Conventionally, CDM columns are designed to have constant diameters over the improved depth as this facilitates the construction procedures. However, this design pattern is found inefficient in cases of spread footings or shallow foundations as the upper soil layers are naturally weaker than the deeper ones but are subjected to larger amount of induced stress from the superstructures.

Jan 1, 2019

By Mahesh Hingorani

Integrity issues for bored cast-in-situ piles have raised the need for the use of non-destructive tests to verify pile integrity and detect possible anomalies in installed pile sections that could adversely affect their serviceability. Integrity inspections performed after installations are often the most reasonable alternative available to assess the shaft quality. The two most common methods are pulse-echo from a small hand held hammer at the pile top, and cross-hole ultrasonic transmissions along the shaft between parallel sonic pipes. While different in technique, each method has its advantages and limitations. This paper emphasizes more on the degree of accuracy of low-strain pile integrity test by comparing the results with cross-hole sonic logging. Reliable data collection and interpretation by an experienced test engineer will reveal the integrity of the pile. Cross-hole sonic logging and low-strain pile integrity testing were both specified as quality control measures for a metro rail project in India. Both cross-hole sonic logging and low-strain pile integrity testing indicated defects in several bored piles. Also minor imperfections recorded by cross-hole sonic logging were observed in low-strain results. The observations of the two test methods are presented and compared for a better understanding of the importance of low-strain test results for any project. INTRODUCTION Cast-in-situ concrete piles are often chosen as a deep foundation alternative where challenging soil conditions exist. Although quality control measures are almost always taken during the installation of the piles, it is often difficult or impossible to confirm the integrity of the pile at this stage, particularly in wet conditions. Because of the relatively high probability of bored piles having anomalies, quality assurance of each bored pile is essential for each project.

Jan 1, 2019

By Chetan D. Savani, Mike K. Muchard

The necessity to evaluate undocumented foundation lengths is essential in assessing the useable life, need for scour protection, retrofitting, or full reuse of existing bridge foundations. For this purpose, Parallel Seismic Testing (PST) has the best accuracy and is applicable to the widest range of foundation configurations used in bridge construction of any test method. Although not limited to bridges, PST case studies are presented involving two bridges. To preface the case study discussions, an overview of the PST method is given along with its results and analysis thereof. In one of the cases, we were afforded the rare opportunity to see the existing piles being extracted long after the PST testing program was completed. The resulting Class A prediction reaffirms the accuracy of the method. Versatility of the PST method is also exemplified in the two cases presented, where unique situations from complex foundation systems were overcome by analysis to provide successful results.

By Nadir Ansari, Brian W. Wilson, Marina S. W. Li

"A hybrid shoring system consisting of cast-in-place soldier piles with Cutter Soil Mixing (CSM) infill panels was constructed for temporary support of a 19.8 m (65 ft) deep excavation in Vancouver, British Columbia, Canada. Deep Mixing (DM) was completed up to 9.7 m (32 ft) in fill, peat, wood waste and clayey silt with embedment in dense till, and soldier piles constructed through the dense till extending to below final excavation level. Two trial CSM panels were installed ahead of production to assist with developing the termination criteria of the CSM panels in the dense till. The constructed depth of the CSM panels was based on interpretation of real-time monitoring data obtained through the Bauer B-tronic system. Inclinometer monitoring data from two CSM panels and two soldier piles, as well as soldier pile survey target data was used to assess and monitor the performance of the hybrid shoring system throughout bulk excavation. The objectives of this paper are to provide an overview of the design and construction aspects of the hybrid DM shoring system and to present inclinometer and pile target data to demonstrate the lateral performance of the CSM infill panels and soldier piles. This paper also discusses the merits of using real-time monitoring data as part of the engineering decision-making process for validating CSM panel construction. BACKGROUND A hybrid DM shoring design was recently completed for a high-rise development in downtown Vancouver, British Columbia for temporary support of a five level basement excavation. Deep mixing was proposed by the excavation and shoring design-build team as the preferred method to construct infill panels between soldier piles because of the speed at which the shoring system could be constructed in variable fill, peat, wood waste and overburden compared with traditional secant piling methods. The development site is generally a truncated triangle in plan, with the longest side of the triangle being approximately 115.7 m (380 ft) long and the two shorter sides being approximately 71.6 m (235 ft) (Hybrid Shoring Wall 1) to 75.0 m (246 ft) (Hybrid Shoring Wall 2) long. The site is bounded by an existing bridge off-ramp structure along its longest side, and by city streets on the other two sides, as shown in Figure 1. The truncated section is approximately 16.8 m (55 ft) (Hybrid Shoring Wall 3) long. Due to project constraints, the hybrid DM and soldier pile shoring system was only proposed for the two shorter sides of the triangle and the truncated section. Traditional secant piles were installed for the longest side. This paper focusses on the hybrid shoring system. A typical detail showing the CSM infill panel with the soldier piles is presented in Figure 2."

Jan 1, 2017

By Ambarish Ghosh, Rituparna Dey, Indrajit Chowdhury

"In port and harbor facilities, jetties and cargo berth terminals are usually installed on piles that remain partially embedded in soil, while a part of it behaves as columns supporting top deck. Technology in vogue adapts a pseudo static analysis in computer where the top deck including piles are analyzed as an integrated system based on finite element method when the piles are modeled as beam elements, while the soil in which it is embedded is modeled as linear or nonlinear springs. Typical berthing force of the ship is considered as a pseudo static force where the dynamic characteristics of the force is taken into consideration by an equivalent impact factor and little study exists on the actual behavior of these type of piles under the transient shock due to berthing impact. Present paper proposes an analytical solution based on which one can compute the dynamic response of such jetty piles considering shear modulus of soil constant with depth. Considering the solution is analytical in nature no special software is needed and can well be adapted fordesign office practice using generic utility software like MATHCAD, MATLAB etc. that makes theproposed model computationally very efficient.INTRODUCTIONResponse of piles under dynamic load has been an important study in the realms of civil engineering, where significant research has been carried out on its dynamic behavior under harmonic loads like one experienced in a machine foundation or under seismic force.A number of researchers have given solution to this problem like Parmelee et al (1964), Tajimi (1966), Penzien (1970), Novak et al (1974, 1983), Banerjee and Sen (1987), Dobry and Gazetas (1988),Chowdhury and Dasgupta (2008).However, most of these theories are based on piles loaded under harmonic load and valid for long piles where structural failure precedes the soil failure considering the piles are long and flexible."

Jan 1, 2015

By Matt Fenwick, Douglas R. Schwarm

Stringent underwater noise limits at the Fairview Ave. N. bridge replacement on Seattle's Lake Union required an innovative approach to supporting the 470-ft long drill trestle. Screw-in foundations would reliably mitigate noise, but the required 500-kip bearing resistance were an order of magnitude higher than typical helical piles. This paper describes the process of designing, installing, monitoring, and testing 22-inch dia. helical piles 80 feet long with 36- and 42-inch dia. helices. A static load test confirmed that the conventional k-factor design method can be extended to capacities of up to 800 kips. A 375 ft-kip drive mechanism had to be fabricated because no North American equipment could supply the necessary installation torque. Real time installation monitoring and later "re-torque" tests confirm that helical piles gain capacity with time, analogous to driven piles under restrike. Underwater and on-land measurements confirmed very low noise, suggesting the possibility of widespread adoption where similar limits are imposed. Overall, this case history illuminates the need for innovative deep foundation types in response to ever-increasing regulatory constraints.

Sep 8, 2021

By Madhav, V., M. R., Ahmad, Padmavathi, M. S.

Modulus of deformation (Es), also referred to as elastic modulus is dependent on many variables such as type of loading, degree of anisotropy and non-homogeneity of strata, etc. and is one of the most challenging soil parameters to estimate. Modulus of deformation of soil can be obtained from elemental tests in the laboratory, from in-situ tests or on the basis of correlations with other soil parameters. Back analysis of full-scale loading test is the most appropriate method for the estimation of the deformation modulus since the effects of installation and pile-soil interactions are accounted for. Moduli of deformation of the ground are estimated from different pile load tests, viz., compression, pull-out, and lateral load tests and compared. The method of interpretation of pile load test is based on the initial liner portion of the load-displacement curve. Theoretical solutions of Poulos and Davis (1980) and Madhav and Poorooshasb (1988) that relate settlement or displacement with load based linear elasticity theory are used. It has been established that the modulus of deformation of the ground is not unique but depends on the type of test and the type of loading. The differences can be significant.

Sep 1, 2022

By Randy R. Williams, Roberto R. Olivera, Brian W. Wilson, Marina S. W. Li

"An extensive, deep mixing (DM) ground improvement program using the Cutter Soil Mixing (CSM) technique was designed and constructed in 2013 to support up to 20 m (66 ft) high Mechanically Stabilized Earth (MSE) walls and bulk earthworks for the development of the Kitimat Liquefied Natural Gas (LNG) facility at Bish Cove, British Columbia. The deep mixing program consisted of overlapping rectangular panels of in situ cement treated soils, constructed using the CSM technique, to form barrettes covering an area of approximately 12,900 m2 (15,428 yd2) and providing suitable static and seismic stability of foundation soils for support of the proposed MSE walls, which would in turn support LNG facilities. The deep mixing program comprised of 1645 CSM panels that were constructed through varying thicknesses and discontinuous layers of very soft fine-grained marine deposits and/or loose sandy silt to silty sand deposits, embedding typically 2 m ( 6.6 ft) into dense silty sand to sand and gravel. CSM panel depths ranged from 5 m (16 ft) to 30 m (98 ft) and were constructed by treating approximately 73,900 m3 (96,658 yd3) of soil yielding average unconfined compressive strengths exceeding 2.5MPa (363 psi).This paper outlines the approach adopted for the design of the CSM ground improvement program in the highly variable subsurface conditions present at the site. A phased sitespecific investigation consisting of boreholes, test pits, Cone Penetration Tests, piston tube sampling, advanced laboratory testing and groundwater monitoring was implemented. In addition, soil-cement bench scale testing was completed, followed by installation of 8 CSM panels for field trial purposes. Extensive geotechnical static and seismic analyses including Limit Equilibrium stability analyses, liquefaction assessments, and advanced numerical modeling were undertaken to optimize the design and meet the project-specific design performance criteria. The Design-Build team worked closely to develop and implement Quality Assurance and Quality Control plans and managed significant construction challenges while achieving suitable panel termination depths."

Jan 1, 2017

By Jason Buenker, Molly Winston

Torque-installed piles are gaining popularity in Southern California as the go-to deep foundation element for small- to medium-capacity loads in urban environments. The torque-installed pile is a displacement- based screwed pipe pile with a closed-end conical tip welded to the bottom of the pipe. Torque-installed piles are most efficient in loose to medium dense soils with high liquefaction potential. Where used properly, torque-installed piles can be installed faster, require less clean-up, and create less onsite vibration/disturbance than other pile alternatives. However, torque-installed piles are not applicable in all soil conditions and care must be used to apply the pile effectively in the correct subsurface environment. This paper will review current Southern California state-of-the-practice for torque-installed pile design and construction, potential roadblocks to successful installation, and available capacities from load tests. INTRODUCTION Torque-installed piles are a type of full-displacement screwed pipe pile originally developed in Southern California circa 2001 by Substructure Support, Inc. The pile is unique for its proprietary closed-end conical tip shown in Fig. 1. The tip has a welded steel-helix plate and cutter teeth that allow the pile to be advanced efficiently under applied torque and down pressure (crowd). Since original development of the pile, several contractors or manufacturers have proposed similar proprietary screw-type piles with comparable conical tips. Pile installation is relatively quiet, vibration-free, does not generate spoils, and faster than comparable pile types. The pile was originally developed as an alternative to driven pile foundations and remains a critical substitute to driven foundations in urban environments. Torque-installed piles are conventionally specified as 12 ¾-inch outside diameter (OD) steel pipes with a ⅜-inch-thick wall, although larger sizes with alternative dimensions have been used outside Southern California. Pile installation lengths generally range from 30 to 50 feet but may reach 80 feet or greater where soil conditions permit. The pile is generally backfilled with concrete following installation to increase lateral pile stiffness and may incorporate rebar cages or other reinforcing steel to facilitate connections to structural elements. The pile is frequently specified using performance-based specifications that encourage contractor innovation and use of proprietary installation means and methods.

Jan 1, 2019

By Francisco A. Flores, José L. Aguirre, Héctor A. de la Fuente, Erika Bernal, Jorge Arroyo-Esquedla

This paper presents the analysis, design, and construction of soil improvement for storage tanks foundation support at a site in Tabasco, Mexico. A total of 980 Rammed Aggregate Piers of 12.5 m in length and 0.5 m in diameter were designed and constructed to support four storage tanks. The soil conditions at the site generally consist of loose to medium dense silty/clayey sand to about 8m depth, underlain by very loose to medium dense silty/clayey sand with seams of very soft clay. The use of Rammed Aggregate Piers induced densification of the soil to increase its stiffness and reduce the liquefaction potential to control both static and dynamic induced settlements. Standard Penetration Test (SPT) and Cone Penetration Test (CPTu) explorations were performed prior to and post soil improvement to compare the liquefaction potential and the Factors of Safety associated with the two conditions. Finally, the soil improvement installation rate is presented. Soil improvement using Rammed Aggregate Piers represented a suitable alternative to support storage tanks foundation in potentially liquefiable areas.

Oct 1, 2022

By J. S. Lee, R. K. Massarsch

"A 3.2 km long immersed road tunnel forms part of the Busan-Geoje Fixed Link in South Korea, which connects Korea's second largest city Busan, with the island of Geoje. To ensure the water tightness of the joints of the segmental tunnel structure and to limit the forces in the shear keys, the differential settlements have to be limited. This was achieved by extensive soil improvement of the marine clay below the tunnel with cement deep mixing (CDM) and sand compaction piles (SCP). This paper focuses on the characteristics of the marine clay, the basic design principles, layout and constructional issues of the CDM soil improvement, and numerical and numerical analyses to predict settlement and stability.INTRODUCTIONThe Busan-Geoje Fixed Link consists of two short cut & cover tunnel access ramps, a 3.2 km long immersed tunnel (Figure 1) and two long span cable stayed bridges. The tunnel consists of eighteen concrete elements each of 180 m length having a rectangular cross section of 26.5 m in width and 10 m in height. The tunnel elements are cast in a dry dock on shore and floated out to the sea, immersed in their final positions on a gravel bed in pre-excavated trench and connected to each other by a dual gasket system. The water depth was up to 50 m making the tunnel of the deepest yet constructed. After immersion, the tunnel is protected by backfill material at the sides and rock armour on top. Each tunnel element consists of eight 22.5 m long segments. The joints between the segments and between the tunnel elements are equipped with EDPM water stops, Omega seals and concrete shear keys. The longitudinal displacement behaviour of the segmental tunnel structure in the varying ground conditions represents a complex soil-structure interaction problem which has been modelled with a FEM structural model representing the tunnel, the joints and with springs to represent the soil that are derived from the PLAXIS soil/foundation models. In order to ensure the water tightness of the joints which have limited opening capacity and to limit the forces in the shear keys, differential longitudinal settlements have to be limited. This is achieved by limiting the variations in subgrade modulus along the alignment and it in practice means that differential settlements are limited to a few tens of millimetres. Without soil improvement of the marine clay below the tunnel, long-term tunnel settlements of up to 400 mm were predicted when taking into account the likely variations in the trench profile, backfilling and uncertainties in the soil properties. Such large total settlements led to large variations in the sub-grade reaction along the alignment, which in turn resulted in significant differential settlements, unacceptable joint opening and large shear key loading. It was therefore decided to carry out extensive soil improvement with cement deep mixing (CDM) (CDIT, 1999) and sand compaction piles (SCP) (Kitazume, 2005) after studying a number of foundation alternatives."

Jan 1, 2015

By Alex Grenoble, Alex Reeb, George Filz, Farzad Abedzadeh

"This paper summarizes available information on the characteristics and properties of deep-mixed soilcement produced by the wet method. The topics covered in this paper include: unit weight, unconfined compressive strength, strength variability for field mixed materials, influence of curing time, influence of consolidation pressure, Young’s modulus, differences in strength and stiffness between small and large samples, creep deformations, Poisson’s ratio, and tensile strength. In addition, this paper discusses the development of design considerations and recommended property values for a project that uses soilcement to protect an existing dam penstock from loads applied by an overlying stability berm. Some of the key recommendations for the deep-mixed soil-cement to be used in this project are that (1) a curved strength envelope that includes tensile strength can be used in the analysis, (2) the stress-strain and strength properties can be characterized using Duncan and Chang's (1970) hyperbolic model, and (3) a specification based on the median unconfined compressive strength value is appropriate.INTRODUCTIONFor many projects, including foundation and embankment support, deep mixing can be designed based on simplified procedures and following standardized guidelines (e.g., FHWA 2013). However for unusually complex or critical projects, it is often necessary to perform numerical analyses, and in order to perform these numerical analyses well, a thorough understanding of the material properties is needed.This paper summarizes information on the characteristics and properties of deep-mixed soil-cement produced by the wet method, and it discusses the development of design considerations and recommended property values for a specific project, herein referred to as the penstock project, that requires numerical analyses. For the penstock project, a horseshoe-shaped enclosure of soil-cement is being considered beside and above an existing dam penstock to protect it from loads applied by an overlying stability berm that will be constructed for seismic remediation. The concept is to use soilcement created by the deep mixing method along the sides of the penstock and to use compacted soilcement above the deep mixing to create the crown of the protective soil-cement zone around the penstock. For this application, the soil-cement stiffness, rather than its strength, is the controlling design parameter. To achieve the necessary soil-cement stiffness, the strength will be high enough that the factor-of-safety values against instability along potential failure surfaces passing through the soil-cement are high. Following conventional practice, the soil-cement acceptance criteria will be based on the unconfined compressive strength, and the specified strength will be selected to produce the desired modulus value."

Jan 1, 2015

By Caciola Jr. Joseph J., Nidal M. AbiSaab

"Thanks in great part to the geology of the New York City Metropolitan area, mini-caissons are a popular choice for deep foundations. These drilled elements are readily available, easy to install with minimal impact on adjacent structures, and can be designed with large compressive and tensile capacities. Despite the frequency with which they are employed, the engineering design community is divided over several of the underlying principles governing the design of mini-caissons. This paper seeks to draw attention to several of these issues in an effort to encourage further research and discussion, namely: (1) how the allowable stresses have changed for the NYC Building Code over time, (2) the inconsistent load transfer mechanisms considered for geotechnical capacity, and (3) the role of the permanent steel casing towards structural capacities of mini-caissons.INTRODUCTIONIn the local construction nomenclature, mini-caissons are drilled deep foundation elements which derive their capacity from a socket in rock. A permanent steel casing (commonly between 7- and 24-inches in diameter) aides the drilling through overburden soils to the top of bedrock. Afterwards, an uncased rock socket is drilled into the bedrock and the inside of the casing and rock socket is inspected by means of portable video equipment. After inspection, the interior of the socket and casing is filled with steel reinforcement and concrete or grout. The casing-soil interface is generally ignored for axial design purposes and the full geotechnical compressive or tensile capacity is assumed to be generated in the rock socket. Figure 1 shows a typical mini-caisson cross section.Mini-caissons have been used for decades in the New York City area for a number of reasons. They have historically been proven to develop high axial capacities in the city’s metamorphic rock (Tamaro et. al. 2000), often exceeding 300- to 500-tons. Additionally, their method of installation (drilling) is generally able to bypass layers of dense Glacial Till, boulders, and manmade fill which would interfere with the installation of other pile types (e.g. driven piles, auger cast piles). Further they are able to extend to depths exceeding 50-ft to reach bedrock underlying a site, making them a useful tool in areas where rock is relatively deep or varied in elevation. Drilled casing installation also results in fewer vibrations and disturbances to adjacent structures and can occur in areas of restricted access (a constant concern for any project in a dense urban environment such as NYC)."

Jan 1, 2016

By Thomas Billups, Brendan FitzPatrick, Doug LeDo, David Carchedi

"Working in urban environments presents unique logistical challenges beyond those typically associated with traditional geotechnical analysis and design. These challenges often include working on sites with limited access and laydown area, vibration concerns for adjacent structures and the need to work from variable elevations or within excavations. This paper describes the use of the modular Ductile Iron Pile system, a low-vibration driven micropile, on two urban projects on the Johnson & Wales University campus in Providence, Rhode Island. The paper describes the successful implementation of Ductile Iron Piles installed to develop capacity in end-bearing on one site and friction on the second site. Design, installation and quality control operations are all presented as well as the results of full-scale load testing performed on non-production test piles. This paper is of importance to the industry because it describes a versatile option for project teams as an alternative to traditional micropiles, helical piles or other deep foundation systems for urban sites.INTRODUCTIONWorking in urban environments presents unique logistical challenges beyond those typically associated with traditional geotechnical analysis and design. These challenges often include working on sites with limited access and laydown area, vibration concerns for adjacent structures and the need to work from variable elevations or within excavations. Two recent projects in downtown Providence, Rhode Island faced a combination of problematic soil conditions and urban construction challenges including vibration concerns. Both projects were a part of the Johnson and Wales University campus development. Figure 1 illustrates the urban locations of the sites."

Jan 1, 2016