Search Documents

By L. Freitag

"The Dollard oil field in southwestern Saskatchewan is a stratigraphic trap of irregular shaped perimeter. The reservoir is a low-angle monoclinal structure with a dip of approximately 100 feet in 5 miles from west to east across the long axis of the reservoir. Production of. 23° API gravity crude is obtained from a Jurassic sand referred to as the J-2-A, at an approximate depth of 4,500 feet. Reservoir studies and fluid analyses revealed that the crude is highly undersaturated, having a solution GOR of approximately 130 cubic feet of gas per barrel, that the reservoir has no definable water table, and that it appears to be of a closed-boundary type. Oil production was marked by a rapid pressure decline and it was soon evident that the greatest ultimate recovery would be best obtained if the natural driving energy of the reservoir were augmented by some artificial energy source. In support of a pressure maintenance programme, studies were conducted on flood-pot recoveries of large-diameter cores, and a potentiometric model study of the field was made. These studies indicated that a successful water flood would be obtained. The Dollard field was unitized in 1955 and pressure maintenance started in March 1956."

Jan 1, 1959

By J. E. Gill, A. R. Byers

"The property of Sladen Malartic Mines, Limited, is in the northern half of Fourniere township, Abitibi county, Quebec. The group is large, but the part so far found to be of economic interest is a strip 3,200 feet long between the Canadian Malartic property to the west and the East Malartic and National Malartic properties to the east ( Fig. 1).The original claims were staked in 1923 and 1924 by St. B. Sladen and H. S. Kennedy because gold was known to occur on claims nearby. In 1928, detailed mapping of the Malartic Gold Mines property (now Canadian Malartic) showed the presence of an east-west gold-bearing zone traceable almost to the Sladen boundary. During the winter of 1929, a hand-driven drill was used to secure short sections of core through casing pipe sunk to bed-rock. This proved the existence of the main Sladen ore zone, but it was not until the price of gold was increased, in 1934, that serious work was attempted.Underground work was started in 1935 and milling in January, 1938. To the end of 1945, 168,882 oz. of gold were recovered from 1,641,974 tons of ore, an average of 0.103 oz. a ton.GEOLOGYThe bed-rock underlying' the Sladen Malartic property consists mainly of Precambrian greywacke and volcanics that appear to form a conformable series with a general northwest strike and vertical to steep northerly dip. Except where disturbed locally by drag folds or faults, tops face north. Intrusive rocks that range in composition from diorite to granite cut the sediments and volcanics. The basic types, generally quartz diorite and diorite, form dykes or sills in the volcanic rocks. The more acidic types, mainly quartz syenite and related porphyries, intrude the volcanics and the sediments in the form of dykes, sills, and larger, stock-like bodies.The orebodies are parts of slightly shattered or brecciated zones, mainly in greywacke, but partly in syenite, diorite, and volcanics, that have been more or less replaced by fine-grained quartz, pyrite, and minor amounts of sphalerite, galena, sylvanite, petzite, and gold."

Jan 1, 1954

By Stanley Davidson

"The ore deposit mined by Falconbridge Nickel Mines, Limited, is one of the numerous nickel-copper sulphide bodies marginal to the large oystershaped mass of differentiated norite in the Sudbury district, famous as the world's most important nickel producing field. The unique character of the ore deposits of the district has resulted in its intensive geological study over a period of more than 50 years. The results of these studies have given rise to a voluminous geological literature and to a great deal of controversy as to the genesis of the ores. This description of the structural geology at the Falconbridge mine is presented in the hope that it may form a small part of the chain of evidence leading to a reasonably satisfactory explanation of the ore genesis.The mine, named after Falconbridge township in which the deposit occurs, lies along the southeast margin of the norite mass, which, however, is h::re concealed beneath a deep mantle of glacial sands and gravels averaging over 100 feet in thickness. As a consequence, the deposit was not discovered by the early prospectors, and it was not until 1916-17 that E. J. Longyear, of Minneapolis, located the ore by drilling(ll). The discovery was foreshadowed in 1899 by the work of Thomas A. Edison, who found indications of the deposit by what is believed to have been a combination of magnetic and electrical geophysical surveys. He sank a prospect shaft over what has to date proved to be the largest and richest ore section in the mine. A wet quicksand layer at the rock surface proved impenetrable, however, and the 'Edison' shaft never reached bed-rock.The Falconbridge property was acquired by the Lindsley interests in 1928, and ore output, since its inception in 1929, has gradually risen from a modest beginning to the present 2,000 tons and more daily. Total production in this period is 7,500,000 tons of ore averaging 1.72 per cent nickel and 0.89 per cent copper, together with a small but valuable content of precious metals, principally of the platinum group."

Jan 1, 1954

By C. M. Trigg

"PEC uranium deposit, 100 km southwest of Coppermine, was discovered by diamond drilling in 1976 following ground and airborne geophysical surveys, geological mapping, geochemical surveys and boulder prospecting that were initiated as the result of the discovery of uraniferous sandstone outcrops in 1969 by geologists of Aquitaine Company of Canada Ltd.The deposit is within gently northeasterly dipping medium to coarse-grained Unit 11 quartzitic sandstone of Neohelikian Dismal Lakes Group. The deposit is from 10 m to 70 m above the base of the sandstone which, beneath the deposit, non-conformably overlies weathered and altered Aphebian granite of Great Bear Batholith or unconformably overlies rubble breccia, conglomerate and medium-grained Unit 8 sandstone of Paleohelikian Hornby Bay Group.A northeasterly trending, 500 m wide graben, bounded by the steeply dipping northeasterly striking Imperial and Aquitaine faults, contains the deposit which is 1.1 km long by up to 340 m wide. The deposit overlies a post-Hornby Bay Group, pre-Dismal Lakes Group topographic high. Uranium principally occurs as stratabound, often peneconcordant bands; a lesser amount of uranium is fracture controlled.Stratabound uranium exists in gently easterly dipping, subparallel bands ranging in thickness from 1.5 m to 6.0 m. Pitchblende, coffinite and sooty black uranium oxides occur as interstitial disseminations and grain coatings subparallel to bedding; they also replace pyrite and form narrow veinlets.Small amounts of torbernite, carnotite and cuprosklodowskite coat pitchblende and are disseminated within mineralized bands. Pyrite, marcasite, chalcopyrite, chalcocite, cove/lite, digenite, azurite, malachite, arsenopyrite, glaucodot, niccolite, bravoite (? ), goethite, hematite and magnetite as well as quartz, barite, calcite, biotite, chlorite and clay minerals exist within the mineralized bands. Uranium grades of 0.1 % to 0.3 % U3O8 over thicknesses of 1 m to 2 m are typical.A steeply dipping fracture zone near the Imperial fault contains sooty black uranium oxides, torbernite, carnotite and cuprosklowdowskite as well as sulphides, cobalt arsenides, quartz and carbonate. The zone may reach 70 m long; its true width is about 1.9 m. Uranium grades range up to 5.18% up, over0.9m.Pitchblende and coffinite from PEC deposit have been dated at 1.08 ± .10 Ga with possible remobilization at .45 Ga. The deposit contains an inferred 3,150 tonnes of U3O8."

Jan 1, 1986

By W. E. Johnston

At last year's Annual Meeting a paper by Haultain and Johnston was presented entitled Is the Gold in Tellttrides Soluble in Cyanide? Since then the writer has continued the study of various phases of this problem. Samples and specimens of ore from some of the Kirkland Lake mines have been studied and non gold-bearing tellurides have been found in these that are not soluble in ordinary mill solutions. Samples of tailings, both old and recent, from this district have been examined with apparatus and methods that have proved very successful in detecting the presence of extremely minute quantities of tellurides. Tellurides, both base-metal and gold-bearing, have been discovered in these tailings, but only in such minute quantities that their presence would not affect the ordinary assay results. More free gold particles have been found in the tailings than gold-bearing tellurides. Much experimental work has been done on tellurides, concentrated from high-grade material and from ordinary run-of-mine ore. The gold-bearing tellurides behave very much as does gold itself. Finely divided particles are dissolved fairly rapidly, coarser particles more slowly. All the tellurides are soft and brittle and also have a high specific gravity, with the result that they are extremely finely divided in ordinary mill practice. The ordinary high-lime solution of Kirkland Lake practice is suitable for the dissolving of the gold tellurides. Oxygen is necessary, but apparently not more so than in dissolving gold. Some particles have been found that appear under the microscope to be ordinary metallic gold particles, but on heating they show a small telluride content. These appear to dissolve more slowly than gold. There is considerable variation in the ratio of tellurides to gold from different points in the mines. So far the writer has failed to find any connection between this ratio and the richness of the ore. Generally speaking, the base-metal tellurides predominate. Some of these contain gold but this may be due to a mixture of tellurides in the one particle.

Jan 1, 1933

By Bryn Harris

Answer to the question is given as 42! Asked the wrong question So got the wrong answer How does this apply to the mining industry? And particularly to this session on Water? Water is just one aspect of mining/minerals/metals Should not be looked at in isolation Need to adopt a ?holistic? approach

May 1, 2013

By J. R. Perumareddi, V. S. Sastri, M. Elboujdaini

It is well known that high strength steels used in aerospace industry, are generally susceptible to hydrogen embrittlement during surface treatment such as electroplating with zinc on cadmium. Hydrogen embrittlement reduces ductility and results in brittle fracture rather than failure by plastic deformation. Hydrogen embrittlement of high strength steels is mitigated by surface treatment such as plating with other metals. Data on the hydrogen contents of steels before and after surface treatment by hot extraction-thermal conductivity, secondary ion mass spectrometry (SIMS) and UV-visible spectroscopy along with the mechanism are presented.

Jan 1, 2006

By W. W. Weber

"The Mine property comprises some 700 acres in ranges VI and VII, Barraute township, about thirty-seven miles due north of Val d'Or in northwestern Quebec.The transformation of a small farming community into the youngest and largest zinc producer in eastern Canada began late in the autumn of 1950. At this time, a geological survey party of the Quebec Department of Mines discovered sphalerite-pyrite mineralization in a strong regional shear structure crossing range VII of Barraute township. Diamond drilling commenced in November 1950, and by June 1951 a total of more than 63,000 feet of drilling, at fifty-foot intervals, had explored an ore zone 2,500 feet in length and 102 feet in average width to a depth of 700 feet, the deepest ore intersection.Production started late in 1952, and is at present in excess of 4,000 tons per day. Production in 1954 of77,790, 166 lbs. of zinc and 989,610 oz. of silver, from 1,525,284 tons of ore, makes this mine the largest zinc producer in eastern Canada.General GeologyAll the consolidated rocks of the area are Precambrian, and most of them are volcanic. They consist mainly of subsiliceous Javas, with smaller amounts of siliceous to intermediate lavas and pyroclastic rocks. The lavas have been intruded contemporaneously by many sill-like bodies of coarser-grained diorite and gabbro. There are no sedimentary rocks within ten miles of the mine.A period of major folding and faulting was followed by intrusion of granite. The volcanic rocks have been compressed into isoclinal folds trending roughly east-west, and the granitic batholiths also show a rude lineal alignment in the same direction. The granitic masses vary consider-ably in composition, ranging from the potassic LaCorne granite, ten miles south of the mine, to the sodic Duverny mass, ten miles west. In addition there is a variation from a general granitic core to dioritic and gabbroic phases on the margins and in satellitic intrusions."

Jan 1, 1949

By S. Malkin, Z. Shi, H. Attia, D. Chellan

An experimental investigation is reported on creep-feed grinding of a nickelbased alloy (IN718) using conventional aluminum oxide grinding wheels. Straight surface grinding expe.riments were conducted on nickel-based alloy blocks over a wide range of grinding conditions with straight oil as- grinding fluid applied at high pressure. Grinding power, forces, workpiece surface roughness, and radial wheel wear were measured. Specific material removal rate as high as 64 mm2/s was Used without burning the workpiece, which can be attributed to the extremely low specific energy of 12.6 J/mm3. It was found that the grinding wheel under the present test conditions had a strong capability of self-sharpening as indicated by the stabilized power, forces, and surface roughness after an initial short transient.

Jan 1, 2006

By C. Zangerl, H. Lechner

"Large scale rock slides in deeply incised Alpine valleys are common hazards that can endanger human life, settlement areas and critical infrastructure such as highways, railways and reservoirs (Bonzanigo et al., 2007). In order to perform reliable forecasts of the behaviour of rock slides influenced by large dam reservoirs the geometry, the kinematics, the deformation behaviour and the hydrogeological situation need to be understood profoundly. Based on generic rock slide models the influence of the rock slide geometry on the stability as well as the impact of the buoyancy forces and water load of the reservoir at the toe of the slope are the main focus of this study. Various assumptions of hydraulic conductivity, groundwater conditions of the rock slide and impoundment depth of the reservoir are analysed using limit equilibrium approaches.Generally, deep seated rock slides are characterised by deformation along one or multiple shear zones where most of the measured total slope displacement localizes. Many large rock slides, especially those observed in foliated, mica-rich crystalline rock masses (e.g. paragneisses, mica schists, phyllites), do not fail suddenly or reach high velocities. Instead, many of them move slowly and reach velocities of centimetres per year or even less. Some show episodic accelerations, sometimes reaching alarming levels, but then subside to non-critical levels again. However, there is a potential that deep-seated rock slides fail rapidly, develop into far-reaching run-out rock flows, and cause catastrophic events. Whereas the role of triggers in promoting phases of acceleration is often understood, the same cannot be said regarding the kinematics and dynamic processes by which the rock slide mass decelerates, re-stabilises or accelerates to a catastrophic degree once the trigger impetus has been removed. Thus key questions of the presented work concern the geotechnical, geometrical and hydrogeological conditions under which a slowly moving rock slide is triggered to accelerate to irreversible, maybe dangerous velocities. The development of the sliding zone is generally influenced by pre-existing discontinuities such as brittle fault zones, shear and tensile fractures, foliation and bedding planes. These geological structures determine the geometry of the sliding zone which can either be rotational or translational. During the gravitationally induced failure process the geometry of the rock slide undergoes a change.Several observed post-failure geometries in metamorphic rocks show a concave topography in the middle to upper part of the rock slide and a typical convex or bulge-like topography at the toe of the slope (Zangerl et al., 2012). Whereas the sliding zone of the upper part of such a rock slide mass is rather steep and planar, the inclination of the sliding zone at the toe can be close to zero and act against the driving forces (Alonso et al., 2010). A shear zone that meets alluvial deposits at the foot of the slope encounters a stabilizing impact on the mechanical behaviour. This buttressing effect of alluvial sediments has a remarkable influence on the slope stability."

Jan 1, 2015

By W. P. Corking

"The purpose of this paper is to describe the relationship of the goldbearing ore to structure at the Pickle Crow mfoe. Information beyond this scope may be found in the reports and papers of Hurst( l), Bothwell(2), Thomson(3) , and Monette( 4).The property lies on Crow river, in Patricia district, 80 miles northeast of Allanwater, and about 125 miles northeast of Sioux Lookout on the Canadian National railway. From April of 1935, when the mill began operation, to the end of 1944, a total of 564,890 oz. gold and 49,275 oz. silver were recovered from 958,416 tons of ore.Mining on the property is at present carried on in two separate orebodies, the Howell and the No. 2 vein. Stoping has been carried on from every level on the Howell vein to a depth ot 2,450 feet below the surface and from several levels on the No. 2 vein through a mile long cross-cut on the 750-foot level to the Howell vein workings. A steadily increasing volume of ore is being obtained from the No. 2 vein.Each of the two orebodies consists of vein quartz with small amounts of other gangue minerals either in a single vein or a stockwork of veins. Both lie within sheared walls and carry gold in the free state. Fig. 1 shows the position of the veins with respect to the surrounding rocks. It will be noted that the delineation of the beds of iron formation shows that the lava flows and minor, interbedded sediments that make up most of the country rocks are areally folded and contorted.STRUCTURENearly all gold found to date in sufficient quantity and concentration to make ore in the Pickle Crow area is confined to these major quartz veins . Both strike a little north of east and dip north, and in both cases the attitude of the enclosing rocks is somewhat more north of east in strike and more steeply north in dip than that of the veins. As a result of this disposition both veins migrate across their enclosing rocks at a moderate angle in both dip and strike. (In this connection it should be noted that No. 2 vein dips at a considerably flatter angle than its host rock, but has a very pronounced rake to the northeast, effecting the same result as in the Howell vein.)"

Jan 1, 1954

By N. Maleki

Magnesium matrix composites are widely used in automotive and aerospace industries for achieving higher performance due to their light weight. The Mg2Si intermetallics compound in Mg/Mg2Si composite exhibits many excellent properties such as high melting temperature, high hardness, and low thermal expansion coefficient. However, under normal cast conditions, the primary Mg2Si phase exhibits coarse Chinese script or dendritic morphologies and the eutectic structures is very brittle resulting in the low ductility and strength of the alloys. Modification treatment is a very effective method to obtain fine microstructure and improve the mechanical properties of the alloys due to low production cost. In this investigation various amount of bismuth addition have been carried out on Mg?5wt %Si alloy to refine and modify the morphology of coarse Mg2Si in order to improve the corrosion resistance of the composite product. The effect of Bi content on microstructure of Mg2Si/Mg composite was investigated by optical and scanning electron microscopy followed by EDX analysis and X-Ray diffraction. In order to compare corrosion resistance of unmodified and modified specimens, Immersion test and potentiodynamic polarization (PD) were used. The results showed that by Bi addition, the size of primary phase Mg2Si was considerably reduced and the morphology was modified from a coarse dendritic shape to a polyhedral shape. The results also indicated that the corrosion resistance of Mg?Si alloys was improved by the addition of 1%wt of Bi due to the reduction, refinement and evenly distribution of Mg2Si phase. Indeed, both the morphology and distribution of Mg2Si intermetallic had a great influence on the corrosion behavior of Mg/Mg2Si composite.

Oct 1, 2011

By E. A. Hart, J. E. Gill

"The property of Arntfield Mining Corporation, formerly Arntfield Gold Mines, Limited, covers an area of 2,110 acres and lies in Beauchastel township, western Quebec. The Francoeur mine lies to the west, and to the east are the West Wasa and Wasa Lake properties.The property was staked in September, 1923, by the late F. S. Arntfield. The early surface work was concentrated in the west part of the property along the Francoeur-Arntfield shear zone. The zone was opened by No. 1 shaft, which was sunk for an inclined depth of 250 feet. A series of silicified lenses were discovered farther east, where No. 2 shaft was later raised to the surface. A third shaft explored a shear zone about 1,900 feet to the east, where No. 3 shaft orebodies were developed.The mill was built at No. 3 shaft and production commenced in July, 1935, at 125 tons a day. This was increased to 280 tons by 1938, and later to 350 tons. The mine continued operations on this scale until April, 1942, when the exigencies of war necessitated closing. The Company was reorganized in 1944 and underground development was resumed in June, 1945. The total value of gold and silver produced to April, 1942, was $2,011, 755 from 529,987 tons of ore.ROCK TYPESThe area is underlain by highly deformed and altered Keewatin volcanics overlain by little deformed Cobalt sediments along the south boundary. The lavas in the vicinity of the mine workings are rhyolite, trachyte, andesite, and a flow breccia of intermediate composition. The fragmentals range from fine, well-bedded tuffs to coarse agglomerate in which acidic and basic horizons can be distinguished.The intrusive rocks are diorite and quartz-feldspar porphyry in the form of stock and sills, and narrow dykes of mica lamprophyre and syenite porphyry."

Jan 1, 1954

By P. E. Auger, J. E. Gill

"The zinc deposits to be described are in Lemieux township a few miles south of the Tabletop mountains, in the central part of Gaspe peninsula, Quebec. Although they have not been worked, they constitute a potential source of zinc and lead and structurally are of considerable interest.GENERAL CHARACTER OF THE OCCURRENCEThe deposits are in sharp-walled quartz-carbonate veins and breccia zones carrying locally, and in varying amounts, sphalerite, galena, pyrite, marcasite, chalcopyrite, and specularite. Those so far investigated strike generally north-south, have steep dips, and cut through sediments of Lower Devonian age, mostly calcareous argillites or siltstones. Wall-rock alteration is negligible.BROADER STRUCTURAL FEATURESThe principal known occurrences are in the south-central part of a dome structure measuring 6 by 5 miles. The argillaceous sediments are overlain, on the flanks of the dome, by sandstones and lavas. These have been stripped from the central part of the dome, revealing the veins in the argillites beneath. The veins formed after the volcanics, but the fractures and breccia zones in which the deposits formed are confined mainly to the argillite series, presumably because of the greater strength of the lavas.The argillite series is cut by dykes, sills, and small stocks of diorite and acidic 'porphyries' that are older than the veins.THE FEDERAL HILL AREAThe distribution of known veins is shown in Fig. 1. The characteristic features of the veins are well illustrated by the Federal Hill area shown in Figs. 2, 3, and 4, and described below."

Jan 1, 1954

"The North Star and Don Jon copper deposits lie beneath the waters of Thompson Lake, which is 12 miles east of Flin Flon, Manitoba. The deposits were discovered during the years 1949 and 1951 by diamond drilling done in the vicinity of pyritic showings on the shores of two small islands in the lake. The Don Jon ore body lies 1, 700 feet southeast of the North Star orebody and is connected with the North Star mine workings by a crosscut on the 600-foot level (Figure 1 ).Production began on January 1, 1955, at a combined rate of 200 tons per day. The ore is trucked, on 24 miles of highway, to the Hudson Bay Mining and Smelting Co., Limited mill at Flin Flon.Regional GeologyRocks in the Thompson Lake area are Precambrian volcanics, ranging in composition from andesite to rhyolite, with related tuffs and breccia. These rocks have a general north-south trend and are steeply dipping. The area is part of the Lac Aimee fault block, which probably is the southward extension of a south-plunging syncline now thrust some miles to the north. This regional deformation has produced many subsidiary zones of intense shearing and crumpling. It is in two of these zones of shearing and drag-folding that the orebodies occur. The only recognizable intrusive is a narrow diorite sill which trends northeasterly near the west shore of Thompson Lake.The North Star MineA pyritic showing, carrying some chalcopyrite, was discovered around the year 1930 on the west side of a small island near the west shore of Thompson Lake. This ground was included in a group of claims acquired by the Hudson Bay Exploration and Development Co., Limited in 1947.In the years 1949 to 1951, a diamond drilling program outlined a copper sulphide orebody. This ore zone comes to surface beneath the lake, about 300 feet north of the pyritic showing on the island."

Jan 1, 1949

By Gordon L. Kidd

The object of this paper is to show the relations of the East Coulee coal area to the near-by Willow Creek, Wayne, Rosedale, and Drumheller areas, all being parts of the Drumheller field. The word ?area? is here used in a more local sense than that employed by Dr. J. A. Allan, whose. 'area' is rather comparable with the 'mining division' in British Columbia. I have drawn freely from the published information, particularly from Dr. Allan's report on the "Geology of Drumheller Coat Field, Alberta", and from Dr. E. Stansfield's paper on " A Chemical Survey of Alberta Coals", to whom thanks are due. The Drumheller field is served by branch lines of the two principal Canadian railways. The C.N.R. traverses the district by its Goose Lake line from Calgary to Saskatoon; and the C.P.R. by a line from Calgary to Acme and then southeasterly to Drumheller, where it effects a junction with the C.N.R., over which the C.P.R. has running rights as far as Rosedale. From Rosedale, a joint line built during the summer of 1928 extends about forty miles down the Red Deer river to the mouth of Bull Pond creek. From that point the C.P .R. turns more southerly to connect with the Bassano-Empress line. The C.N.R., it is expected, will eventually proceed eastward to connect with a transcontinental line. The joint line from Rosedale down the Red Deer river opened up the Willow Creek and East Coulee areas.

Jan 1, 1929

By E. Marcotte

"Technology developments and improvements are imperative to maintain a viable mineral processing industry. In order to achieve optimum implementation of technology in processing plants, safety conscious and efficient work forces are required. Effective management methods are required to prevent employee injuries, equipment or environmental damage and process losses. Good leadership also provides for employees to perform their work in the safest and most efficient manners to attain optimum recoveries of the valuable minerals and produce high quality mill products. Equipment and processes must be designed, operated and maintained as required to assure safe and efficient mineral processing.INTRODUCTIONThe Canadian mining industry must contend with many challenges to attain and maintain a competitive position in today's global market. Canadian Mineral Processors play a vital role in meeting the challenges and achieving optimum mineral productivity.Ongoing technology developments and improvements continue to be imperative to maintain a viable mineral processing industry. The efficient implementation of technology developments requires a safety conscious, skillful and productive work force.In addition to technical and human resources, challenges may also include governments, labour unions or environmental advocates who at times may appear to be misguided or unrealistic. Canadian Mineral Processors must not allow themselves to be overwhelmed by these apparent obstacles but must use their demonstrated ingenuity to achieve successful solutions.It should be recognized that the majority of the Canadian work force are, in fact, a potentially talented and skillful people with ambitions to excel. As leaders of people, we must provide the methodology, incentive and direction that will allow our work forces to realize their ambitions. If the potentials of our work forces are not recognized and leadership is not properly exercised much loss will occur. That is, safe effective and efficient work will not be achieved."

Jan 1, 1993

By Angeles Mendoza Sammet

Based on the analysis of issues associated to conflicts between communities and mining companies in Mexico, this paper suggests actions to make mining more sustainable in Mexico. Interviews with key informants and a revision of documental information available on the internet provided information on 15 cases of conflicts in various parts of the country. The issues varied from incompliance with environmental law to assassination of community members opposing mining. The analysis concludes that mining is not sustainable in Mexico. Both mining companies and the Government of Mexico can make changes to improve sustainability. Mining companies could take a proactive approach and engage in consultation with communities before starting operations. Sharing information with communities on environmental management programs and monitoring results can be a way to start building trust and demonstrate environmental commitments. Companies can implement and evaluate CSR policies to ensure that all staff and contractors are trained on them to reduce and/or prevent corruption and violations of human and indigenous rights. Only 3 of the 15 companies had clear social responsibility policies or sustainability targets, but no reports evaluating them. Complying with the law does not make a project sustainable because of corruption, deficient enforcement, and gaps in legislation. The Government of Mexico should address the following points to make mining more consistent with sustainable development. Update the mining legislation to introduce sustainable development principles and consultation. Incorporate the notion of Free, Prior, Informed Consent (FPIC) for Indigenous People (IP) on all applicable Mexican laws or regulations. The government should not grant concessions on protected areas or indigenous lands without extensive meaningful consultation with the public, IP and land owners. Finally, it is vital to increase SEMARNAT?s capacity to review impact assessment reports and inspect and monitor environmental compliance along the life cycle of projects.

Aug 1, 2013

By T. T. Chen, J. E. Dutrizac, G. Poirier

In the Waelz kiln process, EAF dust is converted to an Fe-rich slag, a (Zn, Fe)-rich dust that is recycled to the kiln and the Zn-rich Waelz oxide which is subsequently up-graded for the recovery of zinc. To clarify the reactions occurring, the Waelz kiln products from a European Waelz plant were characterized mineralogically to determine the mineral species present, their micro-textures and the metal carriers. The EAF dust contains 27 % Zn, and consists mainly of ZnFe2O4 and ZnO, together with minor to trace amounts of NaCl, PbCl2, KCl, CaO, Ca2Fe2O5, Fe203, FRO, Pb oxide and various Ca-Fe-Al-Mn silicates. The KCI and NaCI sometimes agglomerate the other particles. The slag consists of nodules which often exhibit colloform structures. The slag contains of variable amounts of Fe, FeO(OH), FeO, gypsum, Ca(OH)2, Ca2SiO4 and various Ca-Fe¬Al-Mg-Mn silicates as well as minor to trace amounts of ZnFe2O4, Cr-Fe oxide, Mn-Fe oxide and other species. The Waelz oxide contains 57-61 % Zn, and consists predominantly of ZnO, with minor to trace amounts of KCI NaCl, Pb(OH)Cl, Pb20(SO4), Pb chloride, ZnSO4, ZnFe2O4, Ca2SiO4, Ca2Fe2O5, Ca-Fe silicate and NaZn4(SO4)(OH)6Cl.6H2O. The KCI agglomerates the other particles in the Waelz oxide. The recycled dust appears to be a mixture of EAF dust and Waelz oxide, but it contains relatively more coarser-grained metallic Pb and Pb oxide particles.

Jan 1, 2004

By S. Sagar

In September 1996, Dofasco commissioned a 165 Mt twin shell EAF furnace and an associated ladle fleet. During and after this startup, refractory performance in the ladles was optimized on a holistic approach through several initiatives that increased ladle refractory retention times from 7000 to over 16000 mins (160 heats). This dropped the overall refractory costs by 40% while ensuring a consistent and predictable ladle performance. One initiative that drove enhancements was the proper brick selection for each particular refractory area and it's process conditions. The work concentrated on the selection of a resin bonded alumina magnesia carbon (AMC) brick in the barrel area of the ladle, upgrades to the 2 piece monolithic alumina cast ladle bottom and increasing the slagline refractory brick quality with the appropriate zoning/paneling. The adoption of a magnesia alumina carbon (MAC) brick in the transition area of the barrel/slagline has also improved performance and predictability. The design developments have lowered the overall wear rates and balanced the service life of the entire ladle. Safety was improved and breakout potential reduced by changing the safety lining from a high alumina brick to a state of art technology - monolithic shotcrete lining. This initiative decreased the overall manpower required to brick a ladle and increased shop ladle availability. The ladle bricking area environment was also improved by adopting a post combustion device to burn phenol fumes from ladle preheating practices. This has improved the overall health & safety of the reline teams. The consistent and predictable performance of the ladle on a whole has allowed the shop to decrease the number of working ladles in operation from 5 to 4. This further decreased wear rates from over-oxidation and excessive thermal cycling, saving approximately $500,000 in natural gas from pre-heater operations.

Jan 1, 2004