Search Documents

By M. Bigdeli Karimi

In this study, the effect of strain level and holding time in semisolid temperature range via SIMA process on AS21 Mg alloy was investigated. Some cylindrical samples of this alloy with 1cm in height and 2.5cm in diameter (H/D=0.4) were compressed to 10%, 20%, 30% and 40% at 300-C. Then, the samples were reheated in semisolid temperature range at 614°C for various times. The results of optical microscopy and image analysis showed that with increasing of strain and holding time, dendritic structure changed to equi-axed structure, gradually. Also, the best conditions to obtain good globular structure were achieved. Furthermore, it was seen that after compression and reheating, Mg2Si intermetallics with Chinese script morphology converted to dispersed-fine particles which were distributed into the ci-Mg grains.

Jan 1, 2007

By L. Jiang

The evolution of twinning in an AM30 Mg alloy was examined by uniaxial tension and compression testing at temperatures from ambient to 250°C and a strain rate of 0.1/s. The samples were cut along the extrusion direction from extruded AM30 Mg alloy tubes. Specimens deformed to various strain levels were examined by optical microscopy and electron backscattered diffraction (EBSD) techniques. The results indicate that the initial extrusion texture plays an important role in the formation of different types of twins and that the twinning behavior also depends on the strain path. Contraction and double twinning are the dominant twinning mechanisms in uniaxial tension, while extension twinning prevails in uniaxial compression. The different twinning behaviors are shown to be responsible for the sharply contrasting strain hardening characteristics of the experimental flow curves.

Jan 1, 2006

By H. M. A. Rice

"The Ainsworth mining camp is on the west side of Kootenay lake; British Columbia; 14 miles south of the town of Kaslo. It is in one of the oldest mining districts in central British Columbia; for mining started there in 1888. Its principal production was between 1905 and 1920. Activity since then has been sporadic. According to available records; some 222; 000 tons of ore had been produced from the camp up to 1942.GENERAL GEOLOGY Bedrock in the district consists of a succession of quartzite, quartz-mica schist, hornblende schist, and limestone of Late Precambrian, Carboniferous, and Triassic age. Most of the hornblende schists are of volcanic origin but some formed from related intrusions. The Nelson granodiorite batholith of Jurassic age borders the camp on the west. There is also a series of basic dykes of much later age."

Jan 1, 1954

By M. X. Yao, C. D. Opris, P. C. Patnaik, R. Liu, X. J. Wu

Two cobalt-based superalloys, Stellite 694 and Stellite 712, were functionally graded with reinforcement of titanium-carbide particle for high-temperature wear/corrosion applications. The designed composite specimens were fabricated using powder metallurgy (P/M) technique, combined with hot isostatic pressing (HIP). Calorimetric effects of the alloy powders were investigated using the differential scanning calorimetry (DSC) technique, which provided the basis of the sintering cycles designed. The phases present in the microstructures of the materials were analyzed using SEM and X-ray diffraction. The wear resistance of the materials was evaluated on a pin-on-disc tribometer. It was demonstrated that adding titanium-carbide particles to the alloys has increased significantly their wear resistance. It was also found that the HIP process had improved the density of the sintered specimens and thus enhanced their wear resistance.

Jan 1, 2004

By Paul D. Young, Michael J. Allan

"The Con Mine has been producing gold continuously since 1938. In 1990 laboratory and pilot plant investigations began into the use of pressure oxidation for treatment of an arsenic trioxide waste product from two previous roaster operations on the property. This led to the construction in 1992 of a 96 ton/day plant to treat a mixture of arsenic waste and flotation concentrate from the existing mill. The plant was commissioned in the fall of 1992.This paper describes experience gained in the commissioning and initial operation of the plant. The unique aspects of treating a hazardous waste product are described including special operating procedures to satisfy environmental and employee safety concerns. The paper further describes modifications made to the process flowsheet, to operating procedures and to materials of construction in the early months of operation."

Jan 1, 1994

By J. L. Rodrigues Bravo

The aim of this paper is to show the results of the study that relate the variations of the bismuth content in the Caraíba Metais' electrolytic copper with the main electrolysis' process variables as electrolyte flow rate and temperature, anode's impurities content, electrolyte composition, current density, etc and their combinations and factors like cathode washing, blend of materials entering rod plant's furnace, analytical methods, shot-circuit inspection, etc. Also, the methodology considered arsenic, bismuth and antimony mass balance in the electrolysis and their electrolyte's molar ratio relations as well as bibliographic references of refineries that operate in similar conditions. The results showed the circumstances with the major probability of causing bismuth content increasing in the electrolytic copper and the main operating conditions that have to be fixed for having less bismuth variation and lower content in the electrolytic copper.

Jan 1, 2007

By F. Golestani-Fard, A. A. Nourbakhsh

In this paper microstructural development of nitride-Bonded SIC refractories is reported in presence of Al203, Mg() and Urea additives .The samples were prepared by mixing, shaping and firing at 1400-1500°c in a controlled atmosphere furnace. Phase analysis, microscopic observation and mechanical evaluation were taken for microstructural investigations. The strength of samples doped with Al203 was first increased and then decreased at higher amount of Al2O3 additions. The addition of MgO decreased the strength while the urea showed an improving effect on strength. These phenomena could be attributed to microstructural evolution and mainly to liquid phase formation and grain morphology. It was found that the additives such as Al203, MO and urea could modify the microstructure in terms of phase formation and texture modification, which in terms influences the mechanical behavior.

Jan 1, 2004

By Fengxiang He, T. Meadowcroft, Yanjun Zhang

Slag from the zinc fuming furnaces contains about 3 percent zinc and 0.1 percent lead. The paper outlines several experimental techniques for recovering these components from liquid fumer slag. The simplest method, remelting followed by a hold period, indicated that a substantial fraction of the metal values was recoverable as a result of fuming into the gas phase, presumable by reduction of the metal ions by divalent iron ions. Following on from this, slag samples were equilibrated with copper, chosen because the activity coefficients of zinc and lead in copper are very low. This improved metal recovery, with substantial amounts of lead and zinc reporting to the liquid copper as well as to the fume. Application of an electrical emf across the slag-metal interface, using a graphite anode and a liquid copper cathode, resulted in further gains in metal recovery.

Jan 1, 2004

By M. Bueno

Between 1993 and 2003, a series of AG and SAG mill pilot plant trials were conducted using Hardinge Ical pilot plant scale SAG mills on numerous ore samples and ranging across a wide variety of operating conditions. The data from these tests were used to evaluate the design of SAG and AG mill circuits for over a dozen projects, of which about half were eventually constructed and commissioned. The data were also used in the development of SAG mill modelling, scale-up and simulation procedures by several consultants who had access to part of the data set. Recently, we have had the opportunity to bring this data together and further analyse the consolidated dataset. This paper reports on the outcomes of this analysis that has identified the impacts of different AG/SAG circuit flowsheets and operating conditions on energy efficiency and operating cost.

Jan 1, 2012

By Robert Lamarre

In today?s environment, the availability of production equipment is a must to increase throughput and profits. For a number of mining organizations around the world, spare parts availability is key to achieving this goal. Fortunately, having less production equipment immobilized by a lack of spare parts does not equate to increases in inventory levels or in carrying costs. Advance operations research has shown a number of avenues to increase equipment availability while reducing total investment in stock. The presentation will explore these avenues by focusing on key inventory management changes that can be implemented by organizations to optimize their service and stocking levels. We have successfully applied our approaches in start-up mining projects, in mature projects and in end of life mining operations. We will illustrate our methodology using examples from our work with > 30 mining sites around the world.

Aug 1, 2013

By G. E. Agar, R. Stratton-Crawley

"The applicability of a hydrocyclone model to simulation of the cyclone banks in a multi-stage sandplant circuit producing mine back fill has been demonstrated. The model ha~; been used in conjunction with a modular computer program for circuit simulation in order to study the effect of changes in the operating conditions. It has been shown that weight recovery to sand fill increases as feed percent solids decreases, and, to a lesser extent as pressure drop across the banks increases. An increase in apex diameter also causes an increase in weight recovery. Increased weight recovery must, however, be balanced against sump an1l cyclone capacity and dilution of sand fill by fines. The predicted results from circuit simulation were in good agreement with plant data.The model has been found to be applicable to widely different ores."

Jan 1, 1979

In terms of throughput, product size and power draw, grindcurves provide a measure of the response of the mill performance to changes in mill operating parameters – usually mill filling. Since presenting the principle in 2006, grindcurves have been applied to a wide variety of AG and SAG mills. Mill response has been carefully measured for variations in: mill fillings from 15% to 40%; throughput by a factor of two; power by 50%; feed blends; liner profile; and mill speed from 65% to 80%. The outcomes of this extensive program of work are presented as the measured grindcurves. How they have enhanced our understanding of mill operation and how they may be applied to practical daily mill control is discussed. It is proposed that this technique provides a viable and valuable mill control tool that may find extensive application in the industry.

Jan 1, 2012

By Steven Chung

Decision Network Modelling in a mining operation represents a complex process environment that is inherently more variable than a processing plant or factory. The uncertain availability of loading locations, haulage paths, loading and hauling equipment, along with inconsistent operator behaviour, cause a relatively large number of upset events that must be recognized, communicated and dealt with by the appropriate management authority. Traditional process maps that represent a deterministic model of the mining process can quickly break down in the face of such a volatile environment. An alternate modelling strategy, composed of decision networks, focuses on the interactions between goal-oriented entities and their environment, allowing system integrators to explicitly determine the information to be exchanged while providing feedback mechanisms that improve system flexibility and decision quality. This ensures a consistent framework for incrementally increasing system automation.

May 1, 2010

By J. L. Luo, D. G. Ivey, A. H. Adeleke

Double-edge-notched flat tensile samples of X70 steel were used for both slow strain-rate testing (SSRT) and cyclic loading testing with the notch located in the zone of interest, i.e., the weld metal (WM), base metal (BM) and heat affected zone (HAZ). By using both optical and scanning electron microscopy, the stress corrosion cracking (SCC) behaviour with respect to crack morphology and various forms of microstructure was investigated. In all the samples considered, the mode of failure was predominantly transgranular with cleavage facets around the edges of the fracture surface. The BM, with a bainitic microstructure, had the highest resistance to SCC when compared with the mixed microstructures of acicular ferrite-primary ferrite and acicular ferrite-grain boundary ferrite observed in the WM and HAZ, respectively. The effect of microstructure on stress corrosion cracking behaviour is discussed based on experimental observations.

Jan 1, 2005

By Neda Zangeneh

Production efficiency from low permeability gas shales require techniques to optimize hydraulic fracture completions. One completion strategy involves the simultaneous or near simultaneous hydraulic fracturing of multiple horizontal wells to maximize the fracture network area and stimulated reservoir volume. However, changes to the in-situ stress field caused by an earlier hydrofrac on subsequent hydraulic fractures are not accounted for in traditional hydrofrac design calculations. Presented here are the results from a set of transient, coupled hydro-mechanical simulations of a rock mass containing two wellbores using the discontinuum-based distinct-element method. The results demonstrate the influence of stress-shadows generated by a hydraulic fracture on the development of subsequent hydrofracs from an adjacent well. It is shown here that these interactions have the potential to change the size and effectiveness of the hydraulic fracture stimulation by changing the extent of the hydraulic fracture around the secondary well.

Jun 1, 2012

By A. D. Akerman, D. D. Young, G. R. Baiden

The development and maintenance of underground roadways are increasingly important aspects of the modern mining process. With the trend toward automation and track-less mining, roadbeds capable of with standing increased wheel loading have proven necessary to maintain high vehicle speed and reduced maintenance costs. Concrete has been used successfully on some roadways in order to obtain the required characteristics. However, this solution usually involves unacceptable expense. The objective of the Road Router project was to create a drift floor profiling machine capable of cutting a smooth surface out of the existing rock floor of development drifts and ramps. This surface would provide a durable, high strength, low rolling resistance roadbed that would allow for reduced operating cycle times and lower maintenance costs of scoops and haulage trucks. The Road Router has the potential to offer an alternative to concrete with substantial cost savings.

Jan 1, 1997

By Hans Lundberg

During the last few years, geophysical methods have been introduced to aid mining geologists and mining engineers in locating mineral deposits. These methods have been developed as the result of investigations of various physical characters of minerals and rocks. In prospecting for ore-bodies, electrical methods have proved most successful. These methods are based on the great differences in electrical properties, and especially in conductivity, between ore minerals and rock minerals. The electrical resistance of the common minerals, rocks, and ores in ohms per cubic céntimeter is given in the following table: [ ] The first attempts at electrical prospecting were based on observing currents of polarization around certain ore bodies, which currents it was possible to measure. This method has been developed by Prof. Schlumberger and has been utilized by him successfully. He is represented on this continent by Mr. Sherwin Kelly, who has successfully operated the method here.

Jan 1, 1926

By M. S. Moats

As smelter feeds become more complex, the impurities that ultimately report to electrorefineries are changing. Many of these impurities collect in the electrolyte and must be controlled. As commercial copper electrorefineries look to expand their capacities by increasing their operating current density, the interaction between electrolyte composition and anode passivation can cause operational difficulties. To improve the industry's understanding of the passivation phenomena, the role of electrolyte composition was evaluated using commercial electrorefining anode samples. The electrolyte composition variables examined were copper, acid, nickel, arsenic, chloride, thiourea and glue. Finally, the role of non-commercially utilized additives, such as bromide and polyethylene glycol were studied. From this investigation, electrolyte parameters that inhibit copper dissolution through copper sulfate precipitation, copper oxide stabilization and/or absorbed species lead to accelerated passivation. Species that prevent passivation have the ability to complex cuprous ions. Possible mechanisms for the role of each.

Jan 1, 2007

By T. Cutard, E. Cailleux, F. Nazaret, G. Bernhart

This paper deals with the study of the mechanical behavior in the 20°C-900°C temperature range of refractory concretes reinforced with metallic fibers. Fibers are introduced to improve the damage resistance and to minimize the quasi-brittle behavior of refractory concretes. In some cases, a plastic or ductile like behavior can be obtained. Two approaches are considered in these studies. The first one is based on the micromechanical scale. Main objectives are to understand, quantify and predict the thermomechanical behavior of monofiber microcomposites. Such considerations are helpful to optimize the composite formulation for a better behavior. The second one is based on the macromechanical scale. Main objectives are to characterize and to model the macroscopic thermomechanical behavior of randomly reinforced refractory concretes. A particular attention is firstly paid to the relationships between the microstructural changes and the mechanical properties and secondly to the structural size effects.

Jan 1, 2004

By S. R. Izatt

The use of MRT, a highly selective separations technology, has long been demonstrated to be a cost effective, efficient, and environmentally sound process for extraction of a wide range of anions and cations that are commonly found in copper electro - refining and electro - winning circuits, as well as in environmental treatment operations. This paper provides an update of commercial MRT applications in the copper industry. Several recent installations and test programs are reviewed including recovery of bismuth from tank house electrolyte, and from chloride matrix selenium reduction solution which is generated in the anode slimes treatment process. Recovery and refining of platinum group metals originating in the anode slimes is also discussed. Various other base metal and other target separations of interest to the copper producer are also reviewed. The recovery products are high purity metal salts which can be marketed directly or readily reduced to metal.

Jan 1, 2007