Search Documents

By C R. Evans

Whole-rock and muscovite potassium-argon dates from selected low-grade metamorphic rocks of Precambrian age in the Canadian Rocky Mountains near Jasper, Alberta, were obtained to ascertain the age of the source terrain and the age of the metamorphism. Ten argillites gave whole-rock dates ranging from 270 to 485 million years, dates which are apparently inter-mediate between the age of the source material and that of the metamorphism. "Up-dating" increases with the degree of orientation of muscovite in the cleavage plane, and with the ratio of the muscovite in the cleavage plane to that in the plane of the bedding. Detrital muscovite from four arenaceous rocks gave dates ranging from 1,050 to 1,780 million years. "Updating" increases with decreasing grain size, so that, within the range investigated, the cube of the median diameter (¢) of the muscovite is apparently proportional to the radiometric date.

Jan 1, 1964

By D. Kalumba, S. Jjuuko

"Thin Spray-on Liners resist relative small deformations (< 1 mm) between rock blocks or fragments in terms of a combination of shear, adhesive and tensile-bond strengths. Shear-bond strength addresses the ability of a thin liner to resist stresses that act parallel to the rock-liner interface. Therefore quantification of shear-bond strength is essential in the formulation of design standards and requirements for Thin Spray-on Liners. In this paper Thin Spray-on Liner support mechanisms are reviewed. In addition previous methods of Thin Spray-on Liner shear-bond testing are discussed. The paper also explains the research being carried out at the University of Cape Town to investigate the effect of different parameters on the shear-bond strength.INTRODUCTIONRock surface support is widely used to combat rockfalls and resulting injuries and fatalities in the vicinity of active faces (Potvin, 2002), where workers spend most of their time (Adams & Baker, 2002; Potvin, 2002; Lacerda, 2004). The conventional (traditional) surface support systems in underground rock support include passive methods such as mesh and lacing and active methods such as shotcrete. However, rockfall sources between 1990 and 2000 in Nevada gold mines showed a steady increase in rockfall injury associated with mesh support as shown in Figure 1 (Lacerda, 2004). The conventional methods also negatively impact the mining operations with regards to costs, logistics and mining cycle times due to large material volumes (Tannant, 2001; Ozturk & Tannant, 2010; Ferreira, 2012). Therefore, these systems need to be substituted, with enhanced methods, in order to realize the business target of the mining industry of providing the planned return on investment made without harm and within budget."

Jan 1, 2015

By M. Mirnezami, J. A. Finch, M. S. Hashemi A.

The surface of -30µm silica suspension (2% v/v) treated with 100 ppm Mg2+ at pH 11 was fully coated with Mg(OH)2. Under this condition, the silica is strongly positively charged (+30 mV) and the suspension is dispersed. Subsequent addition of Ca2+ promoted aggregation and reduced the surface charge. At this pH calcium is present as Ca2+ and CaOH+, i.e., positively charged ions interacted with the positive surface. Aggregation by a chemical bridging mechanism is proposed. The observation may be relevant to the widespread practice in mineral processing of adding lime to promote aggregation and settling in concentrate thickeners.

Jan 1, 2004

By Adam Jordens

Along with gravity separation and froth flotation, magnetic separation is one of the most common techniques for separating minerals. Minerals are separated by a magnetic force that is dependent on a combination of the applied magnetic field, the magnetic field gradient and the magnetic properties of the minerals themselves. Minerals may be classified as diamagnetic, paramagnetic or ferromagnetic based on the way they interact in a magnetic field. The magnetic susceptibility of a material may be determined by using a vibrating sample magnetometer to determine the magnetic moment of the material in an applied magnetic field and then converting this measured moment into the material?s magnetic susceptibility. In the case of rare earth minerals, magnetic separation is commonly used to remove ferromagnetic iron-bearing gangue minerals and to concentrate paramagnetic valuable minerals such as monazite and xenotime. These magnetic separation steps are frequently preceded by a gravity separation step as many iron oxides and rare earth minerals have specific gravities that are much larger than those of typical gangue minerals. By varying the magnetic field intensity it may be possible to use magnetic separation to selectively separate the paramagnetic and ferromagnetic minerals that report to the concentrate after gravity separation. Test work on a Canadian rare earth ore has shown that a gravity concentration step using a Knelson concentrator was able to selectively concentrate heavy magnetic minerals as evidenced by increased recoveries, relative to the Knelson tailings and fresh feed, after processing through a wet variable intensity magnetic separator. Mass pull to the Knelson concentrate was 4.5 % and the magnetic recovery of this concentrate, at 0.94 T, was approximately 40 % higher than the magnetic recovery from the Knelson tailings (70 % versus 30 %). The products of the wet high intensity magnetic separation were also analysed using a vibrating sample magnetometer to determine the magnetic susceptibilities of the various concentrate and tailings products.

Aug 1, 2013

By R. M. Berry

A brief outline of refining methods used to (1) upgrade yellowcake to nuclear purity and (2) convert the uranium to the chemical and physical forms required by the fuel fabricators is presented. The uranium hexafluoride (UF6) production facility now under construction at Eldorado, Port Hope, is discussed. Technological improvements in uranium refining are considered.

Jan 1, 1969

By W. L. Uglow

In recent years, the microscope has come to be recognized as a valuable aid to engineers whose business is the discovery, development, concentration or reduction of metallic ores. In many of the large treatment plants microscopical research has already an important status; and in the hands of efficient operators the microscope has indicated methods of solving ore problems resulting in the saving of thousands of dollars that otherwise might have been lost in tailings, or expended in freight rates or smelter charges. Failure to procure all the information that the microscope can supply concerning the physical and mineralogical characteristics of complex ores has in many cases led to the construction of unsuitable concentrators, just as the failure to investigate in detail the geological conditions of an ore deposit has often results in the squandering of money on shaft sinking, and mechanical installations which subsequent development of the deposit failed to justify. The great progress recently made in the selective separation of minerals by means of the various processes of flotation and leaching brings strongly to our attention, the scope of the field in which microscopical methods may be advantageously employed. The microscope enables one to observe the minute details of rock, ore, gangue, concentrate, tailing, matte, slag and metal, that are invisible to the naked eye. Furthermore, the technique of microscopal research has been so highly developed that a microscopist can not only observe, but deter-mine the compositions and measure the diameters of the mineral constituents in the ore to be treated. Magnifications of these constituents up to 3,000 diameters may be produced by the proper combination of eyepiece, objective, and projection apparatus, and the images thus viewed may be photographed through the microscope, and permanent records made of them.

Jan 1, 1924

A Joint Venture between Hope Bay Gold Corporation and Miramar Mining Corporation recently acquired the Hope Bay project in Nunavut, which represents the first discovery of a major new Archean greenstone gold belt in Canada since the discovery of Hemlo in 1982 and the Yellowknife belt in 1938. Located some 685 km North of Yellowknife, the Hope Bay Belt is geologically comparable to the other major gold producing regions of Canada. The initial discovery of gold mineralization in 1992 led BHP to acquire virtually all of the Hope Bay belt. Over the subsequent 6 years, BHP expended C$85 million on exploration, including 180,000 meters of drilling, 2.3km of underground workings and a 27,000 tonne bulk sample, as well as extensive environmental and economic studies. Hope Bay Gold and Miramar acquired the Hope Bay property in December 1999 for a cost of C$27 million, considerably less than the C$85 million spent by BHP in exploring the property. They both hold 50% of the project, and share expenses equally. Hope Bay Gold is the manager of all exploration phases and Miramar will manage feasibility, construction and operations. The Hope Bay Joint Venture controls 1,117 sq. km., covering virtually the entire 80 km long Hope Bay and adjacent Elu greenstone belts. We believe that Hope Bay is one of the best-undeveloped gold projects in Canada. Work to date has defined a global resource in excess of three million ounces of gold in three principal deposits, each of which is open to extension along strike and to depth. A C$17 million work program for year 2000 focused on advancing a significant portion of the gold resource to a measured and indicated category. This will provide the basis for initiation of a feasibility study in 2001. The 2000 drill program was one of the largest undertaken in Canada last year, and is a clear indication of our confidence that Hope Bay will develop into a major gold producing district. The majority of the potential mineable areas known to date lie within 350m of surface and would be accessed through a combination of open pit and declines. Currently, development of a 1,800 to 2,000 tpd gold mine producing in excess of 300,000 ounces of gold per year at cash costs below $US200 per ounce is envisioned. In addition, the exploration potential on the 80 km gold belt at Hope Bay is clearly tremendous.

May 1, 2001

The concept and practices of co-extraction of coal and methane have emerged in recent years to improve coal mining safety and productivity, utilise methane resources, and reduce fugitive emissions in environments that involve multiple coal seams with low gas permeability. The system of co-extraction integrates two previously separate operations of coal extraction and methane drainage. The coal mining operation reduces the coal seam gas pressure and creates strata fractures that enhance gas migration and capture from mine workings and surrounding coal seams. An effective methane drainage operation produces a consistent and quality clean energy product and, at the same time, reduces the methane concentration in underground workings and the methane content and pressure in the adjacent coal seams. This is a significant benefit in preventing gas explosions and outbursts, and promotes a safer and more productive coal mining environment. In addition, the co-extraction with enhanced utilisation of coal mine methane directly leads to a reduction in greenhouse gas emissions. Presented in this paper are key results and outcomes of a major Asia Pacific Partnership project carried out from 2008?2012 by the Commonwealth Scientific and Industrial Research Organisation in collaboration with Huainan Mining Industry (Group) Co. Ltd., to develop and demonstrate advanced technologies at Pansan mine, Huainan, that promote the concept and practices of co-extraction of coal and methane. A comprehensive approach was adopted to assess fundamental strata and coal seam methane conditions during mining, and optimise mining sequences and coal mine methane capture systems. The project has not only demonstrated a practical approach and procedures of advanced co-extraction of coal and methane systems but also delivered significant benefits and outcomes in improved mining safety and efficiency, increased methane capture and utilisation, and reduced fugitive methane emissions at the Pansan mine. The total mine gas drained increased from 25.36 Mm3 in 2007 to 47.0 Mm3 in 2011, and the mine gas utilisation increased from 4.94 Mm3 in 2007 to 21.15 Mm3 in 2011. The improved methane capture resulted in reduced coal and gas outburst risks and methane concentration levels at the mine workings, provided a safe working environment for coal production, boosted the mining efficiency, and eliminated methane related incidents over the last few years at Pansan mine.

Aug 1, 2013

By David G. Dixon, Ahmad Ghahremaninezhad, Edouard Asselin

"Atmospheric leaching of chalcopyrite in sulfuric acid solutions is a slow process due to the mineral’s passivation. We have investigated the nature of the passive film in this work. Electrochemical reduction and oxidation of chalcopyrite over the potential range of -0.5 to 1.2 VSHE were investigated in 0.5 M sulfuric acid solution (pH 0.3) at 25 ºC by multicyclic voltammetry and open circuit potential measurement. The influence of scan limits on the evolution of current peaks was studied with both stationary and rotating electrodes. It was observed that the anodic oxidation of chalcopyrite begins at potentials above 0.6 VSHE, most likely by preferential dissolution of iron atoms over copper atoms. The selective electro-dissolution process results in formation of a metal-deficient sulfide passive film (i.e. Cu1- xFe1-yS2, y > x). The passive film dissolves at 0.9 VSHE. Elemental sulfur is one of the products of chalcopyrite dissolution above 1.0 VSHE. Cathodic reactions within the potential region of 0.1 to 0.6 VSHE and anodic reactions at potentials lower that 0.5 VSHE are associated with at least one soluble species from solution. The soluble species involved in the cathodic reactions are likely ferric and cupric, while the soluble species involved in the anodic reactions is likely H2Saq."

Jan 1, 2014

By H. W. McGerrigle

The St. Lawrence Valley of Quebec lies in an earthquake danger zone, the main centers of which appear to be Murray Bay, Montreal and Quebec City. This paper compares conditions in this "earthquake zone" with those of other, currently more active, earthquake zones of the Earth, deals briefly with the mechanics of earth movements and outlines the means by which earthquakes are re-corded. An account is then given of the earthquakes which have occurred in the Province of Quebec -from that of 1534-35 to the earthquake of 1925. A 50-year frequency cycle is implied. The general conclusion is that the 11robability of future earthquakes should be given more consideration in the construction of buildings in the St. Lawrence Valley region.

Jan 1, 1966

By N. Depountis, Th. Rondoyanni, N. Sabtakakis, K. Kavoura, G. Tsiambaos

"Some typical landslide phenomena in Western Greece, in terms of the geological composition and structure of the affected materials, induced by heavy rainfalls are thoroughly studied and analyzed. The studied cases involved composite landslides on Flysch and Neogene weak rock materials that constitute the most critical landslide prone geological formations in Greece. The studied cases named Platanos, Platanitis and Karya include representative landslide sites as regards to the geological composition and structure of the displaced formations. Thus: (a) flysch formation includes different lithological units as shales, marls, siltstones, sandstones and conglomerates and is closely related to the Alpine orogenesis, suffering intense past tectonic movements and (b) the Plio-Pleistocene sediments include clayey marls, marlstones and siltstones. The investigated landslides , affecting mainly transportation routes, are closely related to heavy rainfalls induced by extreme meteorological events and are controlled by active fault tectonics. Long term movement monitoring using borehole inclinometers and surface benchmarks showed that landslides control was effective only when the proper stabilization measures were taken.INTRODUCTIONLandslides represent a major threat to human life, property, infrastructure and natural environment in most regions of the world. They are recognized by the scientific and politic authorities as having a major socio-economic impact and they represent a significant hazard for the population and the properties in particular locations. Landslide hazard expressed as the probability of occurrence within a reference time period and is a function of the spatial and temporal probability (Varnes, 1984; Guzzetti et al. 1999; Lee and Jones, 2004). The spatial probability of landslide initiation (susceptibility) is mainly related to static causal factors (slope inclination, material properties, etc.), while temporal probability is mainly related to dynamic causal factors such as rain input, increased groundwater levels and drainage, earthquakes, etc. (Van Westen et al. 2005)."

Jan 1, 2015

By C. -S. Xie, J. -H. Kong

The microstructure and mechanical properties of X80 hot-rolled thick steel strips with a thickness of 17.5mm produced in Wuhan Iron & Steel Company (WISCO) are introduced in the paper. The steel strips as fabricated through proper thermomechanical processing (TMP)/ on-line accelerated cooling (OLAC) processing have shown high strength and toughness, low brittle transition temperature, good weldability, and high Shear Area (SA) percentage in Drop Weight Tear Test (DWTT). The microstructure of the steel strips is characterized with mainly acicular ferrite, and fine dispersed Martensitc-Austenite (M-A) phases. It is determined that the mechanical properties are improved due to the presence of the fine M-A phases and precipitates, which could be formed by reducing the finish rolling and coiling temperatures.

Jan 1, 2005

By J. Shibata, N. Murayama, H. Yamamoto

As one of effective usages of wastes discharged in the non-ferrous metal industry, the syntheses of AlPO4-5 and hydrotalcite were carried out using aluminium dross as a raw material. AlPO4-5 is an aluminium phosphate condensate with properties of zeolitic materials and large pore size. Hydrotalcite is an inorganic anion exchanger and has a layered structure of complex hydroxide. They were synthesized in an autoclave at high temperature and pressure. Various physical properties such as crystal structure, surface texture, and specific surface area were measured. AlPO4-5 can be synthesized from aluminium dross under hydrothermal conditions at 180°C-200°C, and 3h. At the same time, AlPO4-34 and non-porous AlPO4 were also formed as by-products. The crystals of AlPO4-5 have a hexagonal structure. Lt is desirable to heat the reaction product at around 550 °C to remove tri-ethyl amine. The specific surface areas of the reaction product before and after heat treatment at 550°C were 17.9m2/g and 358m2/g, respectively. Hydrotalcite can be obtained by a co-precipitation method from the aluminium dross and waste MgCl2 solution discharged in the aluminium regeneration process. Small amounts of SiO2, Al2O3, and Fe2O3 remain in the reaction product as an impurity component. The interlayer distance of the obtained reaction product is about 0.3 nm. Hydrotalcite changes to Mg-Al oxide during calcination at 500 °C for 3h, and then hydrotalcite is formed again by a rehydration operation. The physical properties of the reaction products obtained from the wastes were very similar to those from fresh reagents.

Jan 1, 2004

By J. J. Taute, O. S. Tinkler, G. Zárate, K. C. Sole, J. Steeples

Global practice in copper solvent extraction is reviewed, based on individual plant operating data for 2018. The survey respondents account for almost 40% of global copper cathode production by solvent extraction and electrowinning. Regional trends in operating conditions, as related to the prevailing ore mineralogy, leaching processes, and life of mine are evaluated. The adoption and expansion of this technology in the African Copperbelt and Asia are assessed, together with the associated challenges of specific orebody characteristics. Trends in feed and electrolyte compositions and flow rates, and extractant and diluent selection, together with their impact on copper recovery are reviewed. The evolution of equipment design and associated ancillary processes are discussed, and new projects identified. INTRODUCTION Continuing from similar surveys carried out in 1997, 1999, 2003, 2007, and 2013 (Robinson, Davenport, & Jenkins, 1997; Jenkins, Davenport, Kennedy, & Robinson, 1999; Robinson, Sandoval, & Cook, 2003; Robinson, Moats, Davenport, Karcas, Demetrio, & Domic, 2007; Sole, Zarate, Steeples, Tinkler, & Robinson, 2013), global operating practice in copper solvent extraction (SX) in 2018 is reviewed. Contributing operations include established sites in the USA (8), Chile (9), Peru (2), Spain (1), Mexico (2), and Australia (2), as well as newer operations in Africa (7) and Asia (3). This survey represents 2018 copper cathode production of 1.91 Mt, or about 43% of world production by solvent extraction combined with electrowinning (SX–EW). Trends in operating conditions and performance, as well as equipment design and process technology choices are analysed. The significant expansion in production in the African Copper Belt is also discussed. There are currently about 130 operations worldwide producing some 4.6 Mt copper by SX–EW; of these, about half produced more than 10 000 t/a. Figure 1 shows global copper production by country. As it has for several decades, Chile remains dominant, with 36% of global production of cathode copper. Since 2005, the Democratic Republic of Congo (DRC) has increased production year on year, and now represents 23% of the global total (International Copper Study Group, 2017; Statistica, 2018). Copper production in Asia has grown significantly in the past decade, particularly since the ramp-up of Wanbao in Myanmar. There used to be numerous small copper SX plants in China (Schlesinger, King, Sole, & Davenport, 2011), although most of these have now shut down and Chinese production is lower than it was five years ago. The most important trend, however, is the rise of Chinese-owned mining companies, particularly in Central Africa, but also around the world more generally.

Jan 1, 2019

By N. Chow, W. McCombe, G. Remple, J. Nikkari, L. Nightingale-Mercer

Orano Canada Inc. (Orano) operates the McClean Lake mill in northern Saskatchewan, processing high concentration uranium ore, delivered in slurry form, from the Cameco operated Cigar Lake mine. This slurry is ultimately processed into the purified uranium oxide product known as calcined yellowcake. During the calcining process, sulphate (SO42-) entrained in the yellowcake undergoes thermal decomposition into sulphur dioxide (SO2). SO2 is a colourless gas that poses health and safety risks. Since 2016, an anhydrous ammonia dosing system was successfully added to the existing Venturi particulate scrubber system to provide efficient removal of SO2 from the calciner off-gas. Within the pH controlled scrubber solution, SO2 exists in a pH dependent equilibrium with sulphite/bisulphite (SO32-/ HSO3-). The presence of a significant fraction of reduced sulphite and bisulphite in mill solutions presents a hazard in downstream circuits. Should these solutions drop in pH, either through natural oxidation or inadvertent mixing with low pH solutions, the solution equilibrium will shift from SO32-/HSO3- in favour of SO2, resulting in the evolution of SO2 gas from any liquid surfaces. In 2018, Hatch Ltd. (Hatch) and Orano implemented a design change in the calciner scrubber system. Blowdown from this system is now treated in an oxidation pre-step utilizing hydrogen peroxide (H2O2) and anhydrous ammonia (NH3) for pH control, in order to convert the residual sulphite/bisulphite present in solution to stable ammonium sulphate product. This paper will detail some of the challenges and actions undertaken to minimize SO2 risk, culminating in the recent introduction of a novel system designed to oxidize sulphite/bisulphite and prevent mobilization from the calciner scrubber solution into other mill areas where there is the potential for acidification and SO2 release.

Jan 1, 2020

By S. M. Fatemi-Varzaneh

The AZ31 magnesium alloy is considered as a promising alloy in various applications and industries. Furthermore, to design a proper hot working process (rolling, forging and extrusion), the assessment of hot working behaviour of the alloy is necessitated. Accordingly, the hot deformation behaviour of AZ31 alloy was studied through hot compression testing method. The latter was carried out in a wide range of temperature (523 K to 783 K) and strain rates. The obtained true stress-true strain curves and final microstructures were examined and a partial melting was realized at 740 K. It was concluded that the presence of liquid did change the deformation mechanisms thereby affecting the flow behaviour.

Jan 1, 2005

By F. R. Archibald

MR. A. F. B. Norwood: Having been associated in the past few years with nine different plants roasting aurif erous concentrates in Australia, two of which were new installations for which design and construction were undertaken by the writer, I read Mr. Archibald&apos;s paper with very great interest, and I deem it a great privilege, as a member of a sister Institution, to be invited to contribute to the discussion on the paper. I wish to congratulate the author on a very informative and interesting paper, and, although situated many thousands of miles away, I feel I have gathered from it a very close idea of the operating conditions and of the work that has been carried on at the Beattie gold mine. Working along somewhat different lines, it is interesting to note that the conclusions drawn by the author run closely parallel to those accepted in Western Australia, viz., that the object of roasting is to obtain a porous calcine, and that this can best be achieved by roasting first at a temperature below 900 deg. F. to 1,000 deg. F., and then raising the temperature at the finish of the roast. Turning first to the laboratory work, the materials I have studied in Western Australia cover a range from those with little or no arsenic to concentrates carrying as high ?as 20 per cent, i.e., even higher than in the analysis quoted for the eoncentrates from Nepheline Products, Limited. In the ease of arsenic-free pyrite concentrates, the roast is ideally carried out at a temperature ranging from 900 deg. F. to 1,000 ferric oxide is one cause of the refractory gold remaining In deg. F. No improvement in extraction is obtained when the calcines are cyanided by raising the final temperature above this point; nevertheless, in technical practice it is desirable to finish the roast at 1,200 deg. F. in order to decompose basic ferric sulphate and thereby reduce the consumption of chemicals in the subsequent cyanidation step. However, if at any stage of the roast the temperature is raised above 1,200 deg. F., the extraction by cyanidation falls, and continues to do so the higher the maximum temperature that is reached. Line A in the accompanying graph typifies this effect.

Jan 1, 1949

By Frank Martonhegyi

"The objective of this paper is to review the coal basins in the Canadian part of the Western Cordillera to aid their understanding, and to aid in finding and proving places of economic coal mining potential. Coal occurs in eugeosynclinal basins in the Western Cordillera which evolved through three stages: -from systems of volcanic arcs in the Late Jurassic to mid-Cretaceous; -through an intermediate stage with deposition in increasingly restricted successor basins in Jurassic to Early Tertiary; -to a continental stage by the Eocene. Minor coal seams occur usually in late volcanic arc stage sediments bur they can be locally thick as they are on Queen Charlotte Islands. Successor basins usually show a marine-paralic-limnic evolurion. Signijicanr coal deposits occur in the tarter two sequences in the Whirehorse (Tantalus) and Bowser (SkeenaSusrur) basins. Currenr activities are intensive in the more accessible Bowser Basin, for example at Telkwa, Susrut River and on the Groundhog coal field. On Vancouver Island major coal seams occur in cyclic sediments, but the more accessible deposits are mined our. Exploration renewed recently in the less accessible northern part of the Island, for example Quinsam, for surface mineable coal. The Western Cordillera is a mosaic of allochtonous tectonic blocks. They originated from the south and were displaced northward by several hundred kilometres. Many Tertiary coal basins are related to strikeslip transcurrent faults along which the later part of displacement took place, for example the Dawson coal area in the Tintina Trench. Tensional and dipslip normal faulting also created or enhanced sites for thick peat accumulation. For example at Hat Creek 280 m of coal occur in a 550 m section. Secondary structures are often better exploration targets than the main fault zones. Pluvial and alluvial fan environments away from the main drainage are usually the favourable sites for thicker and cleaner coal deposition."

Jan 1, 1985

Strips of AA6111 automotive alloy were cast on a horizontal single belt strip casting simulator, Pure copper and carbon steels substrates plasma sprayed with different coatings for improving the strip surface quality, were used as chill moulds, Experimental studies revealed that a graphite coating provided the greatest benefit in achieving good surface quality. The interfacial heat fluxes during solidification of AA6111 strip were calculated by the IHCP method (Inverse Heat Conduction Problem). Temperature variations and cooling rates within the strips were then calculated through numerical simulations based on the time-dependent heat fluxes obtained by IHCP, The effects of casting parameters, including casting temperature and strip thickness, on interfacial heat fluxes, cooling rates and microstructures, were investigated, Although the maximum interfacial heat fluxes on the chill copper substrate were much higher than the results obtained from the steel substrates, the solidification times of the melts were mainly determined by strip thickness. Very fine equi-axed grains were obtained for both 1.2mm and 2.5mm thick strips thanks to the rapid extraction of heat, and effective grain refinement.

Jan 1, 2005

By Ted Nuorivaara

The use of polymer-surfactant mixtures as foam stabilization agents is a topic that has drawn the attention of several fields but has so far not be thoroughly studied in the context of mineral froth flotation. The present work showcases a study on the impact on flotation performance of cellulose surfactant derivatives and their mixtures with commercial frothers. Bubble size and foam property measurements were run in a two-phase system along with laboratory-scale flotation experiments conducted using a porphyry copper ore from a mine in Finland. A comparative analysis on recovery, grade and flotation kinetics is presented on the products obtained using: i) a partially hydroxylated cellulose derivative (i.e. hydroxypropyl methyl cellulose; HPMC), ii) a commercial polyglycol-ester frother (Nasfroth240; NF240), and iii) mixtures of these two. The results show that using frothers with a total concentration of 30 ppm, the HPMC-NF240 mixtures provide advantages in terms of Cu recovery, (i.e., up to 95%), compared to the use of either NF240 (ca. 76%) or HPMC alone (ca. 1%). Interestingly, only a small proportion of HPMC mixed with NF240 was sufficient to produce a measurable increase in recovery. This improved performance was attributed to a synergistic effect of the polymer-surfactant mixture which further reduced the bubble sizes in a two-phase system compared to that of NF240. The present work offers a further step into understanding the phenomena taking place when a short chained surfactant is either substituted or mixed with a cellulose derivative, offering potential ways of exploiting this behavior for the enrichment of minerals. INTRODUCTION Froth flotation has been the predominant technology used to beneficiate sulfidic copper minerals such as chalcopyrite ever since it was invented in the late 19th century. The reason for the domination of flotation technology lies behind its versatility in selective separation as well as relatively cheap operational costs (Wills & Finch 2015). Even though flotation of sulfidic copper minerals is moderately well understood based on the broad research work done around the subject (e.g., Albijanic et al., 2015, Bournival et al., 2017, Wang et al., 2015, Mikhlin et al., 2015, to cite only a few), the modern era presents new challenges to the primary raw material industry, including questions regarding sustainability of mining operations accompanied by a need to improve the process efficiencies due to declining ore grades (Edraki et al., 2014).

Jan 1, 2019