Search Documents

By A. M. Simons

Cyanide destruction by Caro’s acid is one process commonly employed by gold operations to meet regulatory requirements and/or the International Cyanide Management Code compliance for weak acid dissociable (WAD) cyanide in cyanidation tails or waste water from such operations. Typically smallscale bench tests to evaluate and assess the suitability of the Caro’s acid destruction process are conducted. Additionally, the experimental procedure used during these preliminary investigations may also differ from that implemented at the full-scale. This paper presents the results from a fundamental investigation of the Caro’s acid process to establish a more detailed understanding of the impact that the experimental procedure has on the destruction of cyanide. In particular, it was found that the control of pH was important to avoid copper(I) cyanide precipitation at low pH and maximise WAD cyanide destruction. Residual peroxide in the preparation of Caro’s acid has the potential for subsequent cyanide destruction and could be exploited.

Jan 1, 2014

"Beneficiation of low grade ores is the process of increasing the grade of a mineral through unit operations that remove and separate the waste (or gangue) material from the valuable mineral that can then be used for further processing or direct use. Important factors when deciding upon a beneficiation program are the feed grade, mass yield and the metal recovery. As lower grade ores are being processed beneficiation is a critical process. How predictive is laboratory test work for “as built” operating projects? Beneficiation includes all or some of the available unit operations to produce a beneficiation flow sheet i.e. associated unit operations including but not limited to optical sorting, radiometric sorting, crushing and screening, coarse cobbing, jigging, dense media separation (DMS), spirals, magnetic separation, flotation, thickening, filtering and drying. Reference to specific projects and the approach developed in formulating a beneficiation flow sheet and a comparison of difficult and simple beneficiation flow sheets are cited. INTRODUCTIONReserves of high-grade iron ores are reducing all over the world, at an alarming rate, over the years as a result of the rapid increase in demand for steel particularly from Japan and then China. The recovery of mineral value from the low-grade ores using present technology is more expensive than DSO ores due to high energy and capital costs. Beneficiation is defined as a variety of processes whereby extracted ore from mining is reduced to particles that can be separated into mineral and waste.Various physical properties of an ore can be exploited to separate a low grade fraction including variation in hardness, density, reflectance, conductivity and magnetism.""Beneficiation"" of iron ores includes concentration, generally by physical removal of unwanted gangue. Also considered beneficiation is the regulation of product size, or other steps such as agglomeration to improve its chemical or physical characteristics prior to smelting."

Jan 1, 2012

By H. R. Stockford

"A pyroxenite-carbonatite complex containing extensive pyrochlore mineralization was discovered during January, 1966, within an exploratory license area held by Consolidated Morrison Explorations Limited. Located 32 miles south of Moosonee, Ontario, the deposit was found under 100 feet of glacial till and Paleozoic sedimentary cover using airborne and ground magnetometer surveys. Exploratory and detailed drilling, totalling 47,625 feet in 85 holes, was completed in outlining the deposit to a maximum depth of 900 feet. Pyrochlore reserves are estimated at 62,000,000 tons averaging 0.52 per cent Cb,05 to a depth of 825 feet. Included in this tonnage is a high-grade section containing 10,000 tons per vertical foot grading 0.82 per cent Cb20 5• The deposit is still open at depth and the intrusive complex has by no means been fully explored.The columbium (niobium) mineralization occurs in a lineated calcite-dolomite host rock which has been intruded along a fault zone within a northeast-trending granulite belt. Potassium-argon dating indicates an age of 1655 million years.Preliminary studies suggest that the complex was intruded in a series of pulses in the form of a partially crystallized mush. The James Bay intrusive is unusual in that it is linear in form and contains only two main rock types - p•yroxenite and carbonatite. Nepheline-bearing syenites and associated rocks are notably absent. Moreover, the pyrochlore is essentially non-radioactive and free from many of the impurities generally associated with other pyrochlores. A test shaft to investigate soil conditions and to provide a 250-ton bulk sample was completed during 1968. Subsequent pilot-plant operations indicate that good quality pyrochlore concelttrates can be produced from this deposit."

Jan 1, 1972

By W. E. Selnes

Introduction In 1938, a survey conducted by the Ontario Mining Association revealed a rather startling fact. Injuries incurred in chute pulling were more numerous than those from any other single cause. This report prompted Mr. W. B. Paton, then Inspector of Mines for Manitoba, to make a similar survey of the mines of his Province. It indicated that, in Manitoba mines, chute accidents ranked second only to those from falls off roofs and sides. Why has the mining industry been so slow to recognize the dangers of chute pulling? A partial answer may be the lack of any systematic classification of accidents according to their real cause. The result has been to attribute to other causes injuries which were a direct outcome of chute pulling, and, indeed, has made it difficult to analyze accidents in the industry as a whole. Perhaps, too, because chutes are generally located in the comparative safety? of the drifts, there has been a tendency to consider the occupation as not very hazardous. Not until enough statistics were obtained on this particular task could it be appraised correctly. The Mining Association's survey has been most helpful, and latterly the industry has done a great deal toward analyzing the causes of chute accidents and toward determining an effective means of overcoming them. Much, however, remains to be done. An effort will be made in this paper to outline methods which have been found successful in materially reducing the number of injuries. Qualifications of the Chute Puller First of all it must be realized that chute-pulling is a specialized occupation. The men require proper training for the job, just as in other mining operations. Care must, therefore, be taken to choose persons whose qualifications fit them for the job. Chute-pulling is an integral part of the general mining operation and cannot be considered as isolated from the tasks of other workers. One of the essential qualifications of a chute-puller is a sufficient knowledge of mining operations to appreciate the effect his work will have on the safety of others in the vicinity. He must take the necessary precautions, by verbal warnings, by placing barricades and signs, or by personally guarding the chutes, to prevent accidents to fellow workers.

Jan 1, 1947

By G. E. Veins

This paper summarizes an investigation in which beneficiated ilmenite ore was smelted in a continuous, three-phase, 250 kv.a., open-top electric furnace. Minus %. inch ore was smelted, using the standard method. Fine ore, in the order of minus 14 mesh, was smelted in the briquetted form by the open bath method, and in the unagglomerated form by the cold dry-top method. The latter was shown to be superior. The data obtained .are discussed at some length. During the investigation, slag aver-aging 82.5 per cent Ti02 was produced over a period of 87 hours, the maximum being 85 per cent. Such slag should .be particularly attractive for the production of titanium tetrachloride, from which titaniurn metal is produced. The advantages of using paper-mill bark for producing a furnace charge of low bulk density, as required in cold dry-top smelting, were emphasized.

Jan 1, 1957

By G. V. Sirianni, G. E. Viens, R. A. Campbell, G. N. Banks

A combination shaft-electric furnace for the smelting of ores and the melting of metallized feed is being developed at the Mines Branch. When iron oxide pellets are smelted in this unit, they are preheated and partially reduced in the shaft before being transferred to the electric furnace where smelting is completed. Also, limestone flux added with the pellets is-preheated and calcined in the shaft. It has been demonstrated that, in smelting iron oxide in this unit, the throughput of the 250-kva electric furnace can be approximately doubled and the amount of electrical energy required can be very significantly reduced when the shaft furnace is operated in conjunction with the electric furnace. These benefits are achieved mainly by utilizing the sensible heat and latent energy contained in the arc furnace off-gases.

Jan 1, 1971

By O. Engler, J. Friis, S. J. Andersen, C. D. Marioara, Y. Aruga

"This work investigates the early stages of precipitation in Al-Mg-Si alloys using a combination of high angle annular dark field scanning transmission electron microscopy (HAADF-STEM), selected area electron diffraction (SAED) and density functional theory (DFT) calculations. Quenching from a high temperature (solution) treatment leaves an alloy in a high-energy unstable state, with solute and vacancies in supersaturation. Thus, already at room temperature (RT) a large driving force exists for solute atoms to cluster and order on the Al matrix positions. DFT calculations indicate that strain alleviation is important at this stage. We observe larger regions of Mg-dominated L10 ordering together with a Si-dominated ordering of smaller clusters in a particular geometry connected to the Si-network found in all the precipitates. In addition, building blocks of the main hardening phase ?'', stabilized by vacancies, are observed at higher, typical pre-aging temperatures.INTRODUCTION Al-Mg-Si (6xxx) alloys are widely used in industry due to a combination of favorable properties such as strength, ductility, corrosion resistance and lightweight. They undergo a complex production route, usually consisting of the following thermo-mechanical steps: casting, homogenization, extrusion or rolling, solution heat treatment (SHT) and artificial aging (AA). The SHT takes place at temperatures above the solvus line in the phase diagram, usually between 500°C and 570°C, followed by a rapid cooling to RT. This ensures that high amounts of solute atoms, uniformly distributed on the cubic face-centered (FCC) Al lattice, together with a large amount of vacancies, are quenched-in. The material is therefore in a super-saturated and unstable state. During the subsequent AA, at temperatures usually between 150°C and 220°C, the solute atoms diffuse and cluster, forming metastable precipitates with needle/ lath/ rod morphologies having the main growth direction along <100>Al. With a maximum alloy solute level (Mg + Si) of only 2%, these precipitates increase material strength up to three times that of pure Al, and are essential for the final material properties. To understand and make better use of this phenomenon, it is imperative to research the nature of the precipitates (such as their atomic structure), measure their key parameters (number density, size, volume fraction) and connect it to material properties (Marioara, Andersen, Zandbergen & Holmestad, 2005; Marioara et al., 2014). The following precipitation sequence is given for the Al-Mg-Si system:"

Jan 1, 2018

By Shengwu Song, Xuemin Feng

Jinping I hydropower station is located in Sichuan Province in Southwest China. It is built on the Yalong River as a controlling cascade hydropower station in the middle and lower reaches, with power generation as its major function. Jinping I arch dam concerns many engineering issues and has attracted worldwide attentions due to its huge scale and unique settings. It is one of the most challenging projects in China with its 305 meters high arch dam and complex geological conditions for construction, including large-scale tectonic faults, intensively unloaded rock masses and geological asymmetry in its foundation. At present, the concrete arch dam construction has been completed and preliminarily impounded, most of the foundation treatments have been implemented, and four of six generator units had been put into operation in July 2014. In this paper, the analytical methods, design concepts, treatment measures and technical features of strengthening the geological defects in the dam foundation will be presented. Upon geological investigation into the dam foundation, a few large-scale weak discontinuities are observed. The rock masses in the left dam foundation are intensively unloaded, approximately to the horizontal depth of 150–300 m. These serious geological defects lead to a geological asymmetry on the left and right banks, and thus some major difficulties of dam construction are encountered. The influences of geological defects on the dam construction and safety are analyzed comprehensively, followed by the concepts and methods of treatment design. Based on this, the treatment methods of the weak rock masses and discontinuities are carefully determined by numerical analysis and scheme optimization, including the concrete cushion, concrete replacement grids, drainage system, anti-seepage curtains and consolidation grouting, which work together to enhance the strength and integrity of the dam foundation. Evaluations and calibrations through geo-mechanical model tests in combination with field monitoring results in early impoundment period show that the arch dam and its foundation are generally stable and function normally, which suggests that the research methods and treatment design schemes are reasonable and effective. The proposed treatment methods and concepts in the context are helpful for similar complex rock projects.

Jan 1, 2015

By G. R. Cope, C. D. Spence

"The Mac porphyry molybdenum prospect is located 100 km east of Smithers in central British Columbia. The identification of anomalous levels of molybdenum, copper, and silver in three adjacent lakes, sampled during a regional lake sediment survey, lead to the discovery of molybdenite mineralization in float. Subsequent magnetic and soil geochemistry surveys, together with prospecting and mapping, located the source of the float. Mineralization is hosted by a leucocratic granite stock of the Upper Jurassic to Lower Cretaceous Francois Lake Intrusions which has intruded Carboniferous and Permian Cache Creek Group volcanic and sedimentary rocks. The stock measures 500 m by 300m at surface and is mineralized throughout. Sulphide mineralogy is simple and consists of molybdenite with minor pyrite and local chalcopyrite. Molybdenite occurs within fractures and as selvages along quartz stockwork veins and is best developed near the margins of the stock.Known mineralization is coincident with distinct soil geochemistry and magnetic anomalies. Two additional areas of the property display similar features and these remain to be tested.IntroductionThe Mac property is situated in the Babine Lake area of central British Columbia on NTS map sheet 93K/13E, approximately 100 km east of the town of Smithers (Fig. 1). The property lies on the western margin of the Hogem Range at the northern tip of the Nechako Plateau. The centre of the claim block lies at 54°51 ' 30""N and 125 °34 '30""W.Topographically, the claims are characterized by gently rolling hills ranging in elevation from 900 m to 1500 m. Slopes are forested with tall conifers and underbrush is minimal. Flat-lying areas are swampy with tall grasses and scrub brush.Presently, the property is only accessible by helicopter from bases located in Smithers and Fort St. James. Recent road construction by the British Columbia Forest Service has brought road access from Burns Lake to within 5 km due south of the property. It is expected that in the near future, roads will be advanced into the claim area to facilitate logging of mature timber."

Jan 1, 1995

By R. J. Young, S. J. Tennant, A. D. Drummond

"Gibraltar Mines is located on the western slope of Granite Mountain, 230 air miles north of Vancouver, B.C. and 38 miles north of Williams Lake, B.C. There are four mineable zones within the copper-molybdenite deposit: Gibraltar East, Gibraltar West, Pollyanna and Granite Lake. Open-pit reserves are 358 million tons which average 0.37% Cu and 0.016% MoS2 at a 0.25% Cu cut-off. The Granite Mountain pluton is one of the several Jurassic-Cretaceous intrusions which outcrop along the east side of the Fraser River fault system between Williams Lake and Prince George, B.C. The original Granite Mountain quartz diorite has been metamorphosed by a cataclastic deformation which foliated the rock on a regional scale. Attendant to the development of the foliation, the rock was saussuritized such that the present mineralogy is compatible with that of the greenschist facies. The presence of garnet-bearing assemblages is explained by a restricted increase in water pressure. Pre-mineral intrusive phases within the saussuritized quartz diorite are: (1) leucocratic quartz diorite, (2) aplite and (3) quartz-feldspar porphyry. A late chloritized hornblende dacite dyke is post-mineral. Quartz-feldspar porphyry and leucocratic quartz diorite are locally present on the inner sides of the Gibraltar East, Pollyanna and Granite Lake pits. Their presence suggests a core around which occurs an elliptically shaped sulphide-bearing stockwork. The stockwork, which comprises four ages of vein development, is imposed on and partly controlled by the regional foliation of the samssuritized quartz diorite."

Jan 1, 1973

By I. A. Kovalevska

Considered problems: elaboration and implementation of resource-saving technologies, low-cost support systems improvement, openings security and support, based on wallrock condition control with supreme implication into the rock pressure occurrence counteraction work. Results of analytic and underground investigations using computer simulation of the finite elements in order to calculate stressstrain state of the multivariable geomechanical systems are presented. Solutions of concrete objectives are found using spatial geomechanical model of solid motion around openings, considering real geomechanical parameters formation of support forms with proper conditions of their contact and real mechanical characteristics. Ultimate solutions of resource-saving technologies implementation based on the analysis of multivariate vertical, horizontal, and reduced stresses components calculation and also near-contour rock, support bearing components and security constructions movements are found. Results of experimental investigations of combined supports and security constructions, which increase openings&apos; stability in difficult conditions of flat coal seams are presented.

Aug 1, 2013

By F. N. Smith

The carbon steel casings of Heat Recovery Steam Generators (HRSGs) in a co¬generation plant were found to have developed cracks that originated on the inside surfaces. The HRSGs receive hot exhaust gases from the primary Gas Turbines (GTs), which are fuelled with pipeline natural gas. The GTs was initially operating without any suppression of nitrogen oxides (NOx). After being in service for about two years, some of the cracks were found to have penetrated right through the 1/4 in. thick casings. The casings are fitted with insulation on the inside (hot gas side). Examination of steel samples cut from the casing walls revealed (i) fine cracks propagating through the steel from the inside surfaces, and (ii) the presence of relatively large amounts of nitrate ion on the inside surfaces. It was concluded that the nitrate ions originated from nitric acid that was condensing on the relatively cool walls of the casings behind the insulation. Nitric acid was formed in the GT exhaust gases by the combination of water vapour (formed from combustion of the hydrocarbon fuel and from moisture in the combustion air) and nitrogen oxides (formed from nitrogen and oxygen in the combustion air).

Jan 1, 2005

By C. L. Reichardt

Pressure exerted on gold producers by regulators, project financiers and civil society in the wake of the Baia Mare tailings spill in Romania during 2000 prompted most responsible gold companies to sign up to the International Cyanide Management Code for the Manufacture, Transport and Use of Cyanide in the Production of Gold (the Code). The Code stipulates a ?cradle to grave? approach more comprehensive than that applied to any other mining reagent and poses particular challenges for operators who use cyanide-bearing tailings for backfill. This paper examine some of the challenges for Code compliance facing deep underground gold mines that employ backfill technology, most particularly the requirement to demonstrate that the potential migration of cyanide (and its degradation products) from emplaced backfill will not have an unacceptable impact on worker health and safety or the receiving environment, either during mine life or after closure. Although the Code only contains a single reference to backfill, more careful consideration confirms that most sections of the Code that deal with tailings management are potentially applicable to mines where tailings material is used for backfill, as are certain principles pertaining to aspects of operations, worker safety, emergency response, training and dialogue with stakeholders. For gold mines of the Far West Rand, the most significant cyanide-related risks associated with backfill operations relate to worker exposure to cyanide-bearing seepage and HCN gas. There is potential for seepage of cyanide-bearing water from backfill to compromise the beneficial use of surface and groundwater, and thus impact on downstream users and ecosystems. However, the extreme depth of mining and the specific geological and hydrological controls on the Far West Rand suggest that the potential environmental risks associated with backfill are likely to be considerably less significant than the cyanide-related risks to the workforce.

May 1, 2007

By J. E. Danoczi, J. A. Herbst

"Shore Gold Inc. (Shore) is presently designing a diamond processing plant for the Star and the Orion South kimberlite deposits in the Fort à la Corne (FalC) area in central Saskatchewan. The first step in the plant is diamond liberation and occurs in the comminution section. Diamond liberation is the process of breaking up the kimberlite rock, as gently as possible so as not to damage the diamonds.Autogenous grinding mills (AG mills) use a combination of impact crushing, abrasion and attrition to break up the kimberlite. The forces that occur during the actions of abrasion and attrition cause the kimberlites to break up preferentially along lines of weaknesses which offers a “diamond friendly” method of comminution.Hard competent kimberlite is commonly found in the diatreme zone as well as the root zone of the volcanic pipe and is the source of kimberlite for most of the Southern African diamond mines. Softer kimberlite is typically found in and around the crater area of a volcanic pipe and it is this kimberlite that makes up the majority of kimberlite for both the Star and Orion South deposits. These softer kimberlites can be readily broken up using abrasion and attrition imparted by AG mills. In order for Shore to benefit from the softer kimberlite found in the Star - Orion South diamond project, two large (10.97 m diameter x 7.10 m long) AG mills were designed for the comminution section based on extensive test work and simulations by Metso Minerals (Metso)."

Jan 1, 2012

By A. K. Debnath

Mining being a site specific activity, land becomes the prime requirement for starting, successful execution and closure of any mining project. Many important mining projects are not progressing satisfactorily just because land is not easily available or environmental/social issues are not addressed properly. This is especially true in the case of open-pit mining, which requires large areas for mining, dumping of waste and additional land for other mine facilities. Mine closure & post mining land use exercises, though funded generously, may not achieve their objectives owing to uneven land profile after mineral extraction is over. One of the prominent solutions to these issues is application of steep angle conveyors in large open pit mines that will result in more space for internal waste dumping and enhanced slope stability of the dump. Additionally, such applications will result in economic extraction of mineral in deep open pits. Land reclamation exercise may start concurrently during early years of mine development as mineral evacuation is limited to a specific part of the mine. Surface mining facilities can also be advanced along with the pit by using modular/portable structures. The paper presented here attempts to address specific land related issues by developing suitable schemes and plans that can be practically implemented in open pit mines using advanced technology i.e. steep angle conveyors.

Aug 1, 2013

By Audrey Wagenaar

Introduction ?? Rising public pressures are being placed on companies worldwide to protect the environment and the health and safety of their workers and local communities. ?? International bodies and shareholders want to make sure developments and companies can meet internationally acceptable standards for EHS. In 2005, Golder Associates was asked by the IFC to conduct a comprehensive review and update for their Environmental Health & Safety Guidelines including the mining sector.

May 1, 2008

The NorthMet deposit of PolyMet Mining is located in northern Minnesota, adjacent to the Iron Range. The deposit is polymetallic with values of Cu, Ni, Co, Zn, Pt, Pd and Au. The processing route selected for extraction of these values utilizes bulk sulfide flotation followed by hydrometallurgical treatment. The hydrometallurgical process has been thoroughly tested on the bench and pilot plant scale at SGS Lakefield Research. The major steps in the process are; ? Chloride-assisted total pressure oxidation for extraction of base and precious metals ?Thickening/filtration/washing of the barren residue from total oxidation ? Reduction and precipitation of Au, Pt, Pd from the oxidation solution ? Partial neutralization of autoclave acid using limestone ? Copper SXlEW for production of copper cathode ? Treatment of a portion of the raffinate from Cu SX to recover NilCo/Zn as either a mixed Ni-Co-Zn hydroxide or as separate Ni hydroxide, Co hydroxide and a Zn sulfate solution. ? Recycling of the remaining raffinate to the autoclave as coolant The process flowsheet, chemistry and bench/pilot plant test results will be reported in this paper.

Jan 1, 2007

By Walter Valery, Lauren Hafla, Megan Tibbals, Adrian Dance, Jeff Snyder

"Newmont Mining Corporation’s Carlin (“Carlin”) operation processes roaster feed through a double rotator, dry grinding mill following secondary crushing. Metso Process Technology & Innovation (“PTI”) was involved in a review of crushing and dry grinding circuit operations in August 2009. A number of opportunities for increased throughput were identified in the PTI study.Extended plant trials were conducted in July 2010 to provide justification for possible circuit modifications and if needed, additional equipment. The trials confirmed that a finer crusher product would reduce the build-up of material ahead of the coarse grinding chamber in the double-rotator. Also revealed were material transport and airflow restrictions in the dry grinding circuit that resulted in a high circulating load.The secondary crushing plant demonstrated it was capable of reducing the amount of +¾” material in the mill feed thus increasing dry grinding throughput. However, wet and sticky feed affected screening efficiency resulting in low utilisation of the existing crusher capacity. The open circuit configuration also made it difficult to control crushing circuit product size.For the dry grinding circuit, changes in grinding media size, transfer grate design and increased airflow were recommended to reduce circulating load issues and increase circuit capacity. This paper summarises the crushing and grinding circuit review, the extended site trials performed by PTI and the improvements in dry grinding operation that resulted from this study."

Jan 1, 2012

By Benoît Valley

Optimization of the mining sequence in terms of economics (maximizing net present value) often leads to multi-front mining methods generating pillars. Significant resources are tied up in these pillars, but mining them is often challenging. In order to improve our understanding of rock mass behaviour while extracting these pillars, an extensive monitoring program has been designed and implemented at Vale?s Coleman mine (Sudbury, Canada). The program focuses on existing and new technologies that have potential for monitoring deformation and rock mass property changes. It includes both active and passive methods: gravimeters, multi-point borehole extensometers, fiber optic strain meters, fixed and portable three-component seismic arrays, borehole imaging and sonic logging, and, repeated LiDAR surveys. This paper reports results from an initial project phase, when only a small amount of mining has taken place. The goal was to test and compare technologies in order to assess their sensitivity, accuracy, repeatability and suitability for underground mining conditions. Value is gained by having a broad range of monitoring devices running side by side, enabling comparisons and benchmarking.

Jun 1, 2012

By S. Timbillah, R. LaDouceur, C. A. Young

A low carbon-chain trithiocarbonate ((NaOOC)CH2SCSSNa), known as Orfom® D8, was tested as an organic depressant in the differential flotation separation of chalcopyrite and molybdenite in the presence of sodium isopropyl xanthate (SIPX) or potassium ethyl xanthate (KEX). Flotation studies show that Orfom® D8 depressed chalcopyrite while molybdenite remained floatable. A study of the mechanism of adsorption indicated that Orfom® D8 adsorbs on chalcopyrite through its trithiol (CS -) functional group via both chemisorption and Orfom® D8-metal complexation. The Orfom® D8 depressant is selective and does not form any Orfom® D8-molybdenite bonds. Thus, the combination of the depressant in the presence of either collectors depressed the chalcopyrite and floated the molybdenite. Fundamental parameters of the Orfom® D8 including pKa determination as well as possible decomposition products of the depressant are reported. This study includes an economic case illustrating why using Orfom® D8 can be beneficial. INTRODUCTION Depressants are incorporated in mineral flotation units in the minerals processing industry to make or keep certain minerals selectively hydrophilic. Most reagents used are inorganic and include, for instance, sodium hydrosulphide (NaHS) which is the major reagent used for depressing sulphide minerals, particularly those containing copper, iron and lead. However, the issues with its use include high toxicity, tendency to explode, strong odour, and high consumption due to required high dosages as well as its tendency to oxidise in air. The latter can be overcome by conducting flotation in inert atmosphere such as nitrogen and recycling of the flotation process water. The use of more novel depressants that are essentially organic including homopolar reagents with hydrophilic functional groups on both ends of its structure adsorb onto a target mineral surface with one polar end, the other polar end orients into the bulk solution making the surface hydrophilic and thus, ensuring that the desired mineral does not float. The stringent environmental and safety regulations being implemented in recent times mean that the search for more environmentally friendly chemical reagents is a must have. The use of organic depressants for flotation systems such as Cu-Mo sulfide bulk concentrates has become increasingly important because of the health, safety and environmental issues surrounding the use of inorganic depressants. Nagaraj et al. (1983) investigated the Cu-Mo sulphide flotation system using a structure-activity study of depressants. They found that a major advantage of organic depressants is the ability to tailor-make organic molecules to suit many requirements and thus, eliminate the guess work approach that was predominant in the industry.

Jan 1, 2019