Search Documents

By Kenneth L. Graham

Horizontal directional drilling from existing underground workings will greatly reduce, if not replace, surface exploration drilling. Diminishing ore reserves along with increasing difficulty in acquiring access and permitting of drilling surface holes requires a change in procedure. The length and direction of the required long holes is site specific, but once determined could be quickly mobilized. Data would be available for a much more timely evaluation without any surface disturbance and required reclamation issues. Preplanned directional drilling from underground will also provide an evaluation of already inconsistent uranium deposits located under surface terrain that is inaccessible to surface drilling.

Aug 1, 2010

By G. Bonin, R. P. Preston

"This paper presents a series of case studies where spherical camera photographs were used to generate 3D shaft models using photogrammetric methods. The shaft models were, checked for accuracy by comparing them to overlapping laser scan data, provided survey data or idealized shaft models. Short lengths of model were found to more accurately reproduce the shaft surface, with a best observed accuracy of 8 mm. Longer models encountered errors with accumulated errors as exhibited by slight deviations from vertical or slightly conical model shape. At present, the models are considered acceptable for general documentation and gross change detection. INTRODUCTION Shaft inspections are required by mining regulations in many jurisdictions and are commonly completed by trained mine personnel via visual inspections. This can be time consuming and prone to errors due to lapses in attention and the rapid travel rate required to inspect an entire shaft in a reasonable amount of time. Similarly, because of the time requirements, there can be impacts on other aspects of mining as a result of occupying the shaft for inspections. Spherical cameras with supplemental light systems offer a modern addition or alternative to conventional inspections. These cameras can be lowered relatively quickly to collect high definition, fully illuminated videos of the shaft that can be reviewed in detail later while the shaft returns to service (Gillis et.al., 2019). The use of cameras offers a further opportunity for valuable survey data generation from the same original data stream. The video data can be processed into three-dimensional (3D) models using Structure-from-Motion (Westoby et al., 2012) based photogrammetric methods. Depending on the quality of the source video and availability of survey control (required for all photogrammetry models) these models can be very accurate. Shaft surveying can be conducted with traditional theodolite methods but such surveys are time consuming and limited in their data density. Similarly, scans can be completed using conventional terrestrial laser scanners, but this requires a significant number of distinct setups to provide sufficient overlap between scans. Work is being conducted both on the laser scanning (SLAM, Durrant-Whyte & Bailey, 2006) and photogrammetry fronts towards kinetic scanning (Benecke, 2017) systems. The major advancement which is permitting these kinetic systems is Inertial Measurement Units (IMUs) which can provide localization in GPS denied environments and reduce errors associated with the open traverse format associated with shaft scanning."

Jan 1, 2019

By A. Belleau, F. Lavoie

"Quebec Iron Ore Limited (QIO), a subsidiary of Champion Iron Limited (Champion), secured assets in early 2016 from the previous Bloom Lake operations in the heart of the Labrador Trough region of Northern Quebec, Canada. A plan was developed to bring the Bloom Lake facility back in operation once the iron ore market conditions improved. The project restart involved several aggressive moves to change operational effectiveness, one of which was the utilization of the existing Phase 1 Plant with an upgraded process flowsheet and equipment. The production target was 7.4 million tonnes per annum of 66% iron ore concentrate with an approximate 10% increase in iron ore recovery. The Phase 1 upgraded flowsheet was initially based on review of historical Phase 1 data and pilot testing data undertaken during the original Phase 1 operation and was finalized once additional metallurgical test work and process modeling was carried out by Mineral Technologies in late 2016. The final upgraded flowsheet is comprised of rougher spirals, rougher middling scavenging spirals, and an up-current classifier (UCC) with overflow scavenging spiral stage. A portion of the gravity circuit tailings treated by a series of wet high intensity magnetic separators (WHIMS) to boost overall iron recovery. This paper will describe the efforts taken to test and design the Bloom Lake Phase 1 upgraded flowsheet and report on the plant performance since commissioning in first quarter of 2018.SITE HISTORY The Bloom Lake iron mine property is located approximately 13 km north of Fermont, Quebec, and 10 km north of the Mont Wright iron ore mining complex, property of ArcelorMittal Mines Canada. The Bloom Lake mine facilities include a 32 km railway to efficiently transport the high-quality iron concentrate to a loading port located in Sept-Iles, Quebec. The Bloom Lake property was first explored in 1951 and went through multiple minor exploration campaigns by different companies up until 1998. A major exploration program was conducted by Quebec Cartier Mining (QCM) in 1998. This program included line cutting, surveying, diamond drilling, geological mapping, mini-bulk sampling, bench-scale preliminary metallurgical test work and preparation of a “mineral resource” estimate."

Jan 1, 2019

By W A. Bardswich

The numerous factors associated with the prov1s1on of satisfactory air conditions in hot and humid Canadian mines are described. The main heat sources are auto-compression and the actual flow of heat from the rock. Temperatures reach 97°F at a depth of 8,100 feet. Various methods used in coping with high temperatures are described, including the use of ice stopes and heat exchangers. Moisture control, desirable air volumes and velocities, sizes of airways and methods of distribution are important considerations. A comparison of the temperatures, humidities and types of airways of two deep mines should prove useful in the design of future ventilation systems. Introduction OUTDOOR temperatures in northern Ontario vary from a low of around -40°F in winter to a high of about +90°F in summer. The average annual mean temperature over a 12-year period was +35°F, with a summer mean of 54 o and a winter mean of 16°. Because of low outdoor temperatures, a number of northern mines must heat fresh air for underground ventilation in winter; others, with high rock temperatures, are faced with a year-round cooling problem.

Jan 1, 1965

By B. Farabi Khoshmehr

In the present study the effect of Silicate Sodium oxidation agent concentration and Plasma Electrolytic Oxidation (PEO) treatment time were investigated on properties of oxide layer on Aluminum alloy. The phase composition and surface morphology of PEO films were evaluated through x-ray diffraction (XRD) and scanning electron microscopy (SEM). Pin on Plate abrasive machine were used to investigate of were resistance of coating. The results showed that oxide layer which formed on Aluminum surface consist of high temperature a- Al?O? and ?- Al?O? phases. The diffraction peak intensity and percentage of these phases were increased by increasing silicate sodium concentration. Microscopic studies revealed a porous surface for PEO coating. This was affected by silicate sodium concentration and oxidation time. The wear test results showed that the weight loss of PEO coating was reduced due to improvement of their wear resistance.

Oct 1, 2011

By Bruce K. McKnight

"The new H-W orebody was evaluated by considering its production at three technically feasible rates. Capital and operating costs were estimated f or each rate and production sequences were established using mining cutoff limits generated by an ore value algorithm. The viability of the project was then examined by conducting economic and financial analyses of each of the three production cases under various world economic scenarios. These analyses employing standard profitability measures demonstrated all three cases would be economically viable; the production case which maximized the Net Present Value of the project was the one selected for development and production.IntroductionWestmin Resources Limited and its predecessor company, Western Mines Ltd., has been continuously carrying out mining operations near Myra Falls in Central Vancouver Island since December 1966. The mining operation, whose current production rate is approximately 830 tonnes / day (t/d), based on ore derived from the Myra and Lynx Mines, produces copper, lead and zinc concentrates which contain significant quantities of gold and silver in addition to the base metals.In the late 1970s, with Lynx and Myra ore reserves slipping to unacceptably low levels, a major increase in mine-site exploration was initiated, with outside geological staff brought in to complement the efforts of the mine's geological staff. By the end of 1979, this program had resulted in the discovery of a significant new orebody on a deeper horizon some 300 metres below the one which hosts the Lynx and Myra deposits. Throughout the period 1980-1982, major drilling was carried out to evaluate the new H-W deposit and by the end of 1982, drill-indicated mineral inventory for the deposit compared with Myra, Lynx and Price ore reserves was as shown in Table I. During this same three-year period, a major development and evaluation program was underway comprising environmental monitoring and control programs, shaft sinking test mining, bulk sampling and mill testing, rock mechanics studies and preparation of the Stage I and II reports for the multidisciplinary Environmental Land Use Committee (ELUC).As a result of the preliminary engineering work and exploration drilling, it became rapidly apparent that the H-W deposit could support a considerably higher production rate than the current one. Accordingly, engineering studies including scheduling of development and production as well as capital and operating cost estimates, were focused on three possible production rates: 1350, 1800 and 2700 t/d. Our task was to select the optimum one of these three rates."

Jan 1, 1987

By F. Bélanger, P. Fournier

"The Detour Lake Mine is located in northeastern, Ontario, approximately 300 kilometres northeast of Timmins and 185 kilometres by road northeast of Cochrane. The mill processes a free milling gold ore using both gravity circuit and leaching with a state-of-the-art carbon-in-pulp circuit. The grinding circuit is a conventional SABC circuit with a tonnage of 60,000 mtpd at 95 microns with the addition of pre-crushing upstream of the SAG mill. This paper will highlight the impact of a pre-detox thickener on the cyanide consumption in a gold leach/CIP circuit. While the pre-detox thickener was built with the intention to reduce the cyanide consumption, the opposite effect was observed when the thickener was put temporarily offline. It will show how the re-circulation of a dilute stream of cyanide into the grinding circuit, increases the overall slurry temperature and by the same effect, increases the dissolved copper concentration in the leaching circuit which subsequently increases the cyanide consumption.INTRODUCTION The processing plant is using a conventional gravity, cyanidation and carbon-in-pulp processing facility currently operating at approximately 60,000 mtpd. The comminution process is based on two parallel SABC lines, each fed from an individual reclaim tunnel. Cyclone overflow from the two ball mill circuits is directed to the pre-leach thickener. The thickener underflow is distributed to two (4) parallel leach trains of 5 tanks each, each leach train providing 29 hours of leaching retention time. After leaching, the gold in solution is recovered in a carrousel CIP circuit consisting of two (2) parallel leach trains. Tails from each CIP circuit are combined and sent to a pre-detox thickener to recover as much cyanide solution as is economically practical before being diluted and fed to a cyanide destruction system. The detoxified tailings are sent to the Tailing Management Area (TMA) for settling and retention. The excess water from the TMA is reclaimed and recycled back to the processing plant. The pre-detox thickener is designed to thicken the leach tails slurry to 64% solids with the overflow being recycled to the grinding circuit. It is estimated that the pre-detox thickener will recover 60% of the cyanide in the CIP discharge solution. It is also designed to reduce the SO2 consumption by diluting the thickener U/F to 50% solid using the tailing pond reclaim water which has very little cyanide content."

Jan 1, 2019

By P. Latostenmaa, T. Veneranta, J. Järvi, E. J. Peuraniemi

Boliden Harjavalta has operated a copper flash smelter since 1949 thus the smelter celebrates 70th anniversary of flash smelting in 2019. This paper shortly describes the historical perspective of the smelter and gives an update of the current operational issues and process modifications made during the recent years. The plant has carried out several major investments lately providing a firm view on the future. A new landfill area for the final slag was commissioned in 2018. A modernization of the concentrate storage area, a new acid plant and a debottlenecking project of the smelting line have been recently commissioned. At the same time, the tankhouse capacity will be expanded. This paper focuses on smelter modernizations. INTRODUCTION Boliden is a metal company operating mainly in northern Europe with core competencies in the fields of exploration, mining, smelting and metal recycling. Boliden Harjavalta, located in Finland, is part of the Smelters Business area of the Boliden Group and operates a copper and nickel smelter with related sulphuric acid plant in Harjavalta, and a copper refinery in Pori. As a short historical review, Harjavalta’s history may be dated back to the year 1910 when the Outokumpu ore body in eastern Finland was discovered. By the end of 1913, a copper mine was in operation and a copper plant based on Hybinette process was ready for commissioning. Due to difficulties in metal recoveries and throughput the Hybinette process was permanently shut down in 1929, and 100% of the mining production was sold as concentrate abroad. As the mine production increased steadily, a decision of a new smelter was made in early 30’s. In 1936 Outokumpu’s copper smelter based on electric smelting was commissioned in Imatra. The smelter was dismantled and transferred to Harjavalta during the final stages of the Second World War. The copper refinery started in Pori already in 1941 and the first copper anodes were cast in Harjavalta in 1945. First sulphuric acid plant started operation in 1947. Due to the post-war shortage of electrical energy, the plant metallurgists initiated a major development work to start exploiting the latent heat of concentrates. Thus, the flash smelting method was developed in Harjavalta and commissioned in 1949. Ten years later, flash smelting was also applied for nickel concentrates. Table 1 summarizes major historical and technical milestones of Harjavalta. The history of flash smelting is described in details in another paper of this conference (Jåfs et al., 2019).

Jan 1, 2019

By R. R. Rogers

ABSTRACT The experiments described demonstrate that crude commercial lithium containing in the order of 0.5 per cent sodium can be refined, the resulting metal containing as low as 0.001 per cent sodium. During the process, the metal is vaporized and condensed at a gauge pressure of less than 0.04 micron. Considerable operating data and a detailed description of the experimental equipment are included. INTRODUCTION DUE TO THE unusual properties of lithium metal, its use is likely to increase considerably during the next few years (1, 2). This is of particular interest to Canadians because there are important deposits of lithium-containing minerals, especially spodumene, in Canada and it is hoped that lithium compounds and lithium metal will be produced from these deposits in the fairly near future. In order to assist in the development of this industry, the Mines Branch of the Department of Mines and Technical Surveys has initiated a programme of research in lithium metallurgy. In 1948, a paper (4) was published on methods of producing lithium metal and its alloys. Data on the corrosion resistance of some lithium alloys were included. In 1949, a paper (3) was published which showed that the addition of a small percentage of lithium to zinc anodes used for cathodic protection will improve their usefulness under certain circumstances.

Jan 1, 1951

By R. W. Pauls

"Many tens of thousands of hectares of forested land will be disturbed and reclaimed in the surface mineable Athabasca oil sands area during the next few decades. The surface area disturbed by Syncrude’s Mildred Lake development alone exceeds 10 000 ha to date. It is not clear that reforestation of disturbed areas will best accommodate the aspirations of all stakeholders, particularly traditional users of the land. A five-year research program by Syncrude Canada Limited and the Fort McKay First Nations has examined the feasibility of raising bison on land reclaimed after disturbance by oil sands development. Forage productivity and carrying capacity for bison was comparable to that of grasslands elsewhere in Alberta. Concerns regarding compaction of newly rebuilt soil by bison traffic proved unfounded. Bison demonstrated weight gains typical for ranched bison and calving rates averaged 90%, a value typical for ranched bison. The animal husbandry problems encountered were typical of those occurring on bison ranches elsewhere in Alberta. An economic analysis indicates that a 1000 ha bison ranch on reclaimed land has a net present value that compares very favourably with a similar area supporting commercial forest. Subject to approval by Alberta Environmental Protection, the current research project will be expanded as a pilot commercial ranching venture in order to explore its commercial viability as a business venture by the Fort McKay First Nations. At the same time, measures will be implemented to resolve various regulatory issues associated with commercial bison production in the oil sands area.BackgroundSyncrude Canada Ltd. (Syncrude) is proposing, in its land reclamation strategy, a feature that is, depending on one’s background and perspective, regarded as an innovative approach to land reclamation, a threat to the regional forest industry, a creative response to aboriginal stakeholder concerns, a reneging on reclamation commitments, an opportunity to provide an ongoing economic base for postoil sands regional economy, or an environmentally unsound use of the land. These diverse and sometimes strong reactions have been generated by the proposal to introduce bison, either free-ranging or commercial ranched, to the reclaimed landscape."

Jan 1, 1999

By C. Groccia

As the search for new ore bodies drives mines to be developed at greater depths, the associated high stress environments present challenges for rock support design. Excavations in highly stressed brittle rock are often subject to large volume increases due to rock failure, a phenomenon known as rock mass bulking, which can result in significant wall convergence. Support systems need to be designed to minimize the amount of bulking and to accommodate large wall convergences. In order to design such a support system, empirical guidelines are often used to predict the amount of bulking. However, the empirical guidelines that are currently available are based on a limited number of case studies and consider few input parameters, which may result in an inaccurate bulking assessment. This paper describes methods of collecting quantitative field data at Creighton mine in Canada to better understand rock mass bulking and to further develop the empirical guidelines for bulking assessment for tunnels in highly stressed grounds. Measuring

Aug 1, 2013

By J. Font

New approaches for the fire refining process of blister copper have been carried out at the Codelco Norte Smelter. These have been mainly focused on modification and improvement of the process configuration based in fluid-dynamic and metallurgical studies of the oxidation and impurity treatment stages. This paper presents the results of the laboratory simulations and industrial tests performed in the 250 t anode furnace, evaluating two different process configurations: ? Bottom Bath Agitation System in the vessel during the oxidation stage, ? Dual Flux Injection System during the impurity treatment stage. The results show the possibilities of effective removal of high content of sulfur from the melt during the oxidation stage by using the bottom bath agitation. The use of the dual injection system demonstrated the significant improvement in the removal efficiency of impurities. Cu2007

Jan 1, 2007

By Sadough vanini Ali

Charpy impact energy of functionally graded steels produced by electroslag remelting in crack divider configuration has been modeled in various strain rates. It has been well known that majority of materials indicate different behaviors under different strain rates and temperatures. Therefore, modifying the elastic-plastic model considering the effects of strain rates and temperature gives us an acceptable prediction of these composites behaviors in impact test. In this investigation, graded steel was divided in to several layers in which the layers have the same strains under the impact. Constitutive equation describing the flow stress variations as a function of strain rates and temperatures, have been used to express the stressstrain behavior of layers. The parameter values of constitutive equation determined for all the layers via using the boundary conditions based on composite graded behaviors which were the characterized ferrite, austenite, bainite and martensitte phases. Consequently by applying the rule of phase mixtures and ascribing the impact energy of each layer to the area of stress-strain curve of the same layer, the whole impact energy of composite is the sum of layers impact energy with considering the layers volume fraction.

Oct 1, 2011

By S. Kamado

Development of new SF6 alternative cover gas with low global warming potential is strongly desired for melting and casting of magnesium alloys. We have tried to apply several kinds of HFC and HFE gases with low potential from 30 to 950 as protection gases to AZ91D alloy melt in the temperature range of 650 to 800°C. As a result, protective film consisted of MgF2 and MgO is formed on the melt surface and ignition-proof effect is sufficiently obtained at all the temperature ranges even when flow rates of mixed gases containing CO2 as a carrier gas are almost the same as those using SF6 gas. Reduction of global warming potential exceeds 98% at 650°C and 89% at 800°C in comparison with a mixed gas of CO2 and SF6.

Jan 1, 2006

By T. G. Joseph, M. Welz

ABSTRACT: Joseph (2002) introduced passive seismic monitoring to measure mining equipment performance. This paper evaluates the potential of passive seismic monitoring to correlate mining equipment operation with oil sands surface response, with a mining hauler as the seismic source. When applied to moving haulers, this action–reaction approach is complex. Vibrations from on-board equipment, such as pumps and tires, dirty the signal with noise. To facilitate any correlation, the signal must be cleaned up. Existing geophysical analytical techniques were manipulated to evaluate the noise problem and to filter sufficiently to permit an evaluation of whether a mining equipment action–ground response relationshipis in fact discernable.

Jan 1, 2011

By Julia Pflieger, Manfred Russ, Johannes Gediga

This paper shall show an economic feasible approach to implement Greenhouse Gas (GHG) reduction measures into the mining and metallurgy industry. The goal to improve energy consumption is directly linked to the reduction of GHG emissions and therefore directly in correlation with the economic viability. A baseline scenario of the considered reference system and of the respective reference year has to be defined, mapped and analysed. In a second step an analysis of the same operation using available and prospected Best Available Technology (BAT) processes is carried out to generate a basis for a benchmark system. The identified reduction potentials are reported and the GHG emission reductions are put into relation to the investment cost of the new process technologies / process adaption to be implemented. This economic feasibility calculation is necessary to realise a cost efficient GHG reduction roadmap implementation into the company's business operations. The GHG reduction roadmap is developed using ratios between GHG reduction and investment / operating cost to get an indication for a sequence for implementing carbon emission reductions measures.

Jan 1, 2010

By D Marshall

The sub-level blasthole benching method of mining has been proved to be economical at Willroy Mines. How-ever due to the nature and attitude of the wall rock, this method is susceptible to serious hanging-wall dilution of the ore. Attempts to solve the dilution problem by various means were not satisfactory until long Stressteel bars were employed as rock bolts. The adoption of this de-vice does not require any special skill, and has become routine in the under-ground operation. Since the inception of this method, the dilution of the ore has been greatly reduced and the ov1!r-all costs of controlling this dilution are much lower. INTRODUCTION T HIS is a report describing the successful use of long Stressteel bars as rock bolts in preventing l1anging-wall failure and consequent dilution in open stopes. Willroy Mines Limited is located (Figure 1) near the town of Manitouwadge, Ontario, approximately l1alf-way between Sault Ste. Marie and Port Arthur.

Jan 1, 1963

By J. Starkey

A comminution circuit in recent history, is one of the most difficult parts of a mineral processing plant to design with confidence. It is usually the most costly part of a plant to build, and it can consume up to half or more of the energy used on a mine site. To suggest that comminution energy usage is sustainable in the long term is not possible at this time. What we have to choose from today, based on more than 50 years of experience, does include the best available technology, and the best way to design it. There is controversy in the industry as to how to properly approach the subject of comminution design, with many of the optional solutions requiring a level of training and expertise beyond the ability of a non-specialist engineer. Semi-autogenous grinding technology in particular, has not been properly appreciated because of many recent mistakes in its application and design, which have blurred the positive perception about what SAG technology is, how it can be used, and how it needs to be designed and built. In order to change this, mine owners and senior managers need to take responsibility for, and learn to understand the fundamental challenges that a comminution circuit poses to the project, to the design process, to the operators who use the equipment, and to the resulting metallurgy. This address is intended to summarize these challenges and offer fundamental engineering solutions, which are clear, specific and in a format which is directly applicable to the mining and mineral engineering community.

Jan 1, 2018

By S. A. Sadough vanini

In this paper, Stress-Strain-Temperature relations for Shape Memory Alloys are studied. Temperature effects on Shape Memory Alloys are different from those related to ordinary materials. In ordinary materials, elastic characteristics can be assumed to be constant in low temperature ranges, and only the deflection arising from temperature changes could be added to the elastic defection. As long as two phases of austenite and martensite could be present in Shape Memory Alloys simultaneously, elastic modulus follows temperature and temperature gradient. In continue a smart actuator is investigated considering a homogeneous cantilever beam. Beam bending is established by using shape memory wires. An initial strain is imposed to shape memory wires in a low temperature, and then, they are installed in the outer surface of the beam. Therefore, since the temperature is imposed in these wires and they cannot have free recovery strain, the compressive recovery stress will be produced in the outer surface. This will result in a deflection in axial direction of the beam. At first, beam deflection is calculated on the basis of theoretical relations and solving the relevant differential equations. Afterwards, experimental tests are performed on an elastomeric beam equipped with shape memory wires. When a voltage is applied, a temperature rise will occur in the wires; then, this temperature rise causes a deflection in the beam. Finally, the theoretical and experimental results? comparison indicates a good conformity. One capability of this actuator is its high flexibility, and by controlling the inlet current, the end-beam deflection can be controlled.

Oct 1, 2011

By I. Soosaiprakasam

This work investigated inhibition performance of copper carbonate (CuCO3), which is less toxic than conventional heavy-metal corrosion inhibitors in amine treating plants, The investigation was experimentally carried out in a bench-scale electrochemical corrosion cell under an atmospheric pressure, The inhibition performance of CuCO3 in an aqueous solution of monoethanolamine (MEA) was examined under a wide range of operating conditions and reported as a function of process parameters including inhibitor concentration, temperature and solution velocity, The results show that CuCO3 functions as an anodic inhibitor. The addition of CuCO3 decreases corrosion rate of carbon steel but might induce pitting corrosion/

Jan 1, 2005