Search Documents

By W. B. Agocs

"IntroductionWITH THE DISCOVERY of natural radioactivity at the end of the 19th century, and the design of equipment for the detection of this phenomenon, radioactivity surveys bad their inception. Early in the 20th century it was found that almost all rocks are radioactive to a certain degree. This radioactivity is due to the nuclear disintegration of six naturally radioactive elements: potassium, thorium, uranium, rubidium, samarium, and lutecium.The radioactivity of these elements manifests itself by the emission of some concentration of alpha, beta, and gamma 'rays'. Of these, the alpha and beta 'rays' are, respectively, helium atoms and electrons, while the gamma 'rays' are short wave length x-rays generated in the nuclear disintegration by the transformation of mass into energy.The alpha and beta rays, being particles of matter, are stopped ve• easily by material barriers, but gamma rays are extremely penetrating and they will pass through a foot or more of rock or several inches of lead.The radioactivity may be detected by the causing of ionization by the radiation. The radiation detectors may be divided into four classes: ionization chambers, proportion al counters, and Geiger counters, all of which use gas for ionization, and scintillation counters, in which a solid is ionized. The basic principle of all these detectors is the same; the difference lies in the method used to measure the degree of ionization produced by the rays. Currently, the scintillation counter is displacing, the other instruments in radioactivity surveying."

Jan 1, 1955

By R. Tipman

"In 25 years, processing of tar sand progressed from two small pilot plants to two major commercial operations owned by Syncrude and Suncor. These plants mine tar sand and extract the bitumen which is then converted into a synthetic crude oil. Considerable research on extraction of bitumen from tar sand has been undertaken by these two companies as well as other major oil producing companies, private individuals, universities and the federal and provincial governments. These studies have produced a number of alternate processing schemes which have yet to be commercialized. The producing companies are focusing their efforts on achieving increased processing efficiency, which includes improved bitumen recovery, reduced unit cost, energy conservation, and equipment reliability. In this review, the Syncrude process and examples of new process developments will be briefly described. IntroductionTwenty-five years ago, tar sand processing was limited to two pilot plants owned by Cities Service Athabasca Ltd., and Great Canadian Oil Sands. Earnest Manning was Premier of Alberta and was inviting proposals for the construction of a commercial tar sands plant. The invitations called for a much larger operation than those which had been undertaken in the past. All of the previous attempts at commercial operations up to 1960's had failed, largely because of a poor technical understanding of the process requirements, lack of suitable equipment, and lack of adequate capital. The previous record was not good. The pending new large scale plant was based on improved but not proven technology and equipment, which were developed from the pilot plant studies. In addition, the surplus of conventional oil in Alberta and low world oil prices were factors reducing the need for such a plant."

Jan 1, 1987

By Esteban M. Domic

"T.L. Leaching ProcessCommercial PerformanceSociedad Minera Pudahuel Ltda. (SMP) has been innovating in the copper producing field with the commercial application of the Thin Layer (T .L.) leaching process in its two operating division s: Lo Aguirre and La Cascada. Since November 1980, SMP' s Lo Aguirre Division has been producing high-purity copper cathodes at a nominal rate of about 16,500 metric tonnes / year, by mean s of the new route of T.L. leaching, followed by solvent extraction and electrowinning (TLlSX/EW). This has been the first commercial application on T .L. technology in the world, and the only commercial application in Chile for solvent extraction and electrowinning.By mid -1980, SMP acquired Sagasca Mining Co., renaming it as La Cascad a Division. The existing vat leaching facilities were modified to apply T.L. in the same old vats. The existing scrap iron cementation recovery circuit was kept running for the continuing production of copper precipitates. The modifications in the leaching circuit allowed shorter treatment cycles with a lower acid consumption and consequently, copper product ion increased from a previous historical high of 12,000-13,000 metric tonnes /year to a new level of about 22,000 metric tonnes/ year . These changes have been in operation since March 1981.T.L. Leaching commercial performance, both at Lo Aguirre (TL / SX /EW) and at La Cascada (TL/cementation), has been presented in several recent publications. Real operating parameters and process requirement s were reviewed in detail. A breakdown for TL / SX/ EW economics was also published based on Lo Aguirre' s performance during 1982(41."

Jan 1, 1986

By B P. Scott

Podsol soil horizons developed on Pleistocene glacial sediments overlying the Coronation Mine orebody were analyzed for copper and zinc spectro-photometrically, using biquinoline-isoamyl alcohol and dithizone carbon tetrachloride reagents. Copper and zinc are concentrated in the A. and C horizons, whereas the A1, A2 and B horizons are leached. Of economic significance is the fact that the C horizon contains a copper anomaly, in excess of 100 times back-ground, directly over the orebody. Due to the erratic distribution of high copper concentrations in the Ao horizon with respect to the orebody, that horizon is not considered as a reliable prospecting datum. U NDER certain conditions, metallic ore deposits are accompanied by primary halos of trace elements in unweathered rock surrounding the orebodies or by secondary halos in weathered rock, alluvium, soil, or vegetation above or near the mineralized zones. Where such halos occur, chemical analysis, as applied to the detection of trace elements, is a valuable prospecting aid, permitting the detection of mineralization of possible economic value.

Jan 1, 1965

By M. M. C Jiménez, D. C. Buzzi, D. C. R. Espinosa, J. A. S Ténorio, G. F. R Oliveira

In this work the extractive and selective capacities of solvent extraction synergistic systems to recover nickel and cobalt were evaluated. The liquor used was from the high pressure acid leaching process (HPAL). Initially the industrial liquor, processed from lateritic ores, was analyzed to identify the concentrations of the metals. Experiments of synergistic solvent extraction were performed later. The extraction liquid-liquid was carried out with a mixture of Cyanex 272 (CY) and Ionquest 290 (IQ) extractants. The process was executed with the temperature of 65 ºC, pH of 5.2 and the ratio aqueousorganic 2:1. Systems of 80% kerosene and CY 20%, CY 16% - IQ 4%, CY 12% - IQ 8%, CY 8% - IQ 16%, CY 4% - IQ 16%, IQ 20% were studied during 20 minutes. The results of this paper showed that the mixture of these two extractants doesn’t improve significantly the recovery of nickel and cobalt from liquor.

Jan 1, 2014

By Joseph Daniels

When Dame Nature shook her horn of plenty and distributed her bounties over the face of the earth, she blessed the Pacific coast with many riches, but with these she added many offsetting disadvantages or handicaps, designed, no doubt, to effect a proper balance between wealth and economy. Nowhere is the application of the law of compensation more aptly illustrated than in the matter of fuel and power resources. A glance at the map of the Pacific northwest will show that west of the Coast Range batholith we are bounteously supplied with coal, with timber, with water power, and with tributary resources of oil from California. Alaska, British Columbia, Washington, all contain large resources of coal; Oregon and California to a lesser degree, but, compensating the golden state for its deficiency in this respect, oil was placed in the treasure ,chest. Timber, of wide variety and in lavish quantity, covers the forests from tidewater to mountain slope, and within this protected watershed area flow streams which give the Pacific coast states the largest single share of the potential water-power resources of the country. Something over 40 per cent. of the total estimated horsepower of the United States is to be found in the Pacific states, and British Columbia has 15 per cent. of the total for Canada; but of this total less than 10 per cent. has been developed.

Jan 1, 1924

By S. C. Radopoulou

Pavement condition assessment is an indispensable constituent in maintaining roadway infrastructure. Current practices for pavement condition assessment are labor intensive which introduce subjectivity in pavement rating and are time consuming. Automated methods rely on full 3D reconstruction of the pavement surface which introduces high equipment and computation costs. This paper presents a methodology for detection of patch type distresses in asphalt pavement images. This method uses filtering and histogram equalization for clearing and enhancing the image accordingly. It continues by applying the morphological process of closing, along with some rules based on the characteristics of a patch when captured in an image, to finally detect the area it occupies. Criteria for area, length, and width of a patch as seen in an image are taken into account to decide whether a probable patch is actually a patch. The method has been implemented in C#. The preliminary experiments demonstrate it produces promising recognition results

Aug 1, 2013

By Stewart W. Daniel

"Increasing labour costs, the trend to larger mills, the processing of lower grade ores and a diminishing sup-ply of well-trained and experienced mill operators contribute to the necessity of automating a grinding circuit. With sophisticated process control techniques, supervision of the mill line is reduced to an occasional inspection by the shift supervisor. Process operating decisions and/or adjustments are quickly and accurately performed by the electronic devices to be described. When the variables in the grinding circuit are stabilized using the sensors and controllers as discussed, the over-all grinding circuit is maintained at its optimum grinding load level, with ample protection against under-and overloading."

Jan 1, 1967

By B. MohammadSadeghi, S. Bakhshivash, M. Haghshenas, F. Rahimi

"Constrained groove pressing (CGP), as a severe plastic deformation (SPD) technique, is one of the applicable methods for sheet metal forming capable of producing ultra-fine grained materials (UFGMs). In CGP, processing and die design parameters can significantly affect the deformation response of sheet metal specimen. Having said this, in the present research the effects of die design variables and processing parameters (i.e. shear angle and friction) on the deformation behaviour of an Al-Mg-Si Alloy are studied thoroughly. Finite element analysis (FEA), was used to evaluate the effectiveness of mentioned parameters on the deformation homogeneity, strain distribution and pressing load variations. Also, mechanical properties of the deformed sample in term of micro-hardness was analyzed. It is observed that with increasing the shear angle, effective stress, strain and pressing load are enhanced. Moreover, by increasing the coefficient of friction, pressing load enhances. The color coded micro-hardness measurement showed a good agreement with the strain distribution obtained from FEA (higher hardness for the zones associated with higher shear plastic strain values).INTRODUCTIONWork hardening results in enhanced mechanical properties upon cycles of deformation (Hosford & Caddell, 2007). However, the formability of the processed products are affected by work hardening reducing the possibility of processing in subsequent deformation cycles. Therefore, many industrial processes cannot be performed on sheet metals to produce products with desired mechanical and physical properties (Valiev, Islamgaliev, & Alexandrov, 2000). Severe plastic deformation (SPD) is an effective grain refining technique which can impose large plastic strains through cold working on a metallic specimen (Bisadi, Rastgou, Payganeh, Zeynali, & Ghahremani, 2010). SPD techniques are mainly categorized into three types; sheet, bulk and tube forming. Among SPD sheet forming methods, Constrained Groove Pressing (CGP) (Shin, Park, Kim, & Park, 2002), Accumulative Roll Bonding (ARB) (Saito, Tsuji, Utsunomiya, Sakai, & Hong, 1998) and Repetitive Corrugation and Straightening (RCS) (Zhu, Lowe, Jiang, & Huang, 2001) possess potential applications in manufacturing industries."

Jan 1, 2016

By W W. Moorhouse

A survey of recent literature indicates that sulphides occur in the volcanic rocks of the Archean, or in sedimentary rocks intercalated with the volcanic rocks. The thick sedimentary sections are generally poor in sulphides. Thus, the widespread pyrite and pyrrhotite mineralization in the Archean may be largely of volcanic origin. Introduction I N this paper, commercial base-metal deposits will not be considered, as they are dealt with in other papers of the Symposium. Instead, attention will be focused on those sulphides, often associated with graphitic argillites or tuffs, which have appeared in such embarrassing abundance in electromagnetic surveys of Archean areas. The data on which the paper is based are drawn from recent reports of the Ontario Department of Mines, the Quebec Department of Natural Resources and the Geological Survey of Canada. The information available from these sources is unfortunately limited, because sulphides commonly occur in sheared rocks, such as black argillites and tuffs, which rarely form conspicuous outcrops, and may not be exposed at all. Thus, in the absence of geophysical information, even detailed mapping may fail to reveal the presence of sulphide-rich rocks.

Jan 1, 1965

By M. Feinendegen, Ph. Siebert, C. Clauser, K. Willbrand, M. Ziegler

"Three institutes of RWTH Aachen University collaborate on laboratory tests and numerical simulations of hydraulically driven fractures in igneous rocks. The project´s target is to enhance the understanding of hydraulic induced fractures for deep geothermal energy exploration. Based on the idea of creating new discrete fractures in hot dry rock (HDR) reservoirs, the current project stage deals with this process on a laboratory scale. Especially for this purpose, a new testing facility has been developed and laboratory tests are performed to verify a hydraulic fracture propagation code based on the extended finite element method (XFEM). The testing facility enables us to initiate and propagate fractures in large samples of dense rock under triaxial confining pressures and to monitor the fracture propagation by extensive measurements. This contribution gives a short introduction to the project‘s background and mainly focusses on the test facility, the experimental procedure and exemplary results.INTRODUCTIONThe most efficient technique to increase the permeability of subsurface rock is to initiate and open fractures by applying hydraulic pressure from a packed borehole-section and to inject fluid into these fractures to propagate them. Since its first use in petro industries to enhance the production of wells in natural gas and oil reservoirs, the interest in targeted creation of hydraulic fractures has increased exponentially. As the key technology to the extraction of unconventional gas from shale, hydraulic fracturing (HF) became a major topic in a heated public debate. Based on the fact that a fracture tends to propagate in a direction perpendicular to the minimal principal stress, hydraulic fracturing has become an established tool for estimating geological stress states in almost any depth. Enhanced geothermal systems (EGS) in HDR reservoirs use engineered fractures as a heat exchanging system for a cycling fluid driving a power plant."

Jan 1, 2015

By E. H. Kranck

Introduction Baffin Island is still too in-accessible to be of interest to the mining industry. However, twenty years ago few people dreamed of mining iron ?ore in Labrador. A journey by air to the most remote places in the Arctic is today no more remarkable than a trip to Europe, and the technical difficulties of mining minerals of high value are not insurmountable. Some ?observations concerning the geology and mineral possibilities of Baffin Island, the largest of the Arctic islands, may therefore interest the members of the Institute, in spite of problematic practical value of the subject. The following short account is mainly based on observations made during the Baird Expedition of the Arctic Institute of North America last summer 1950), and on information available from earlier expeditions. Early Work Baffin Island was one of the first parts of Canada to attract prospectors. Frobisher sent a shipload of rocks, which he believed contained precious metals, from Baffin Island to England. This attempt, however, was a failure and no further serious prospecting work has, so far as I know, been done. During the past few years geological mapping has been carried out by the Geological Survey of Canada (Fortier. Davison, 1949-1950) in the southern parts ?of the island, along the coast of Hudson strait. In 1942, Weeks mapped the coast from Pangnirtung to the head of Cumberland fiord, and Netteling river up to Netteling lake. In the northern parts of the island, only scattered observations have been made ?by Bell, Watkins, Baird, and others.

Jan 1, 1951

By A. Alfantazi, M. Mahon

The current efficiency in zinc electrowinning is a key indicator of the performance in a cell house. This is typically measured by comparing the weight of the cathode to the electric current applied over the deposition period. This calculation can be cumbersome because the deposition history of each pulled set of cathodes will be unique. It will depend on the applied current and electrolyte conditions from onset of deposition until the cathode is removed and stripped. Not accounting for these can introduce errors to the calculated current efficiency. To track this history and reconcile the current efficiency, a time based computer process simulation was made of an industrial cell house. Two months of hourly recorded measurements from the cell house were input to the simulation, including current to the cell houses, concentrations, flow rate, and temperature of the purified leach solution. The simulation’s predictions of the concentration of zinc in the circulated, spent, and returned electrolyte all showed good agreement with the industrial data over the two months giving a validated zinc balance. The simulation was then tuned to predict the instantaneous current efficiency for all times, as well as the expected masses for the deposits given their deposition history.

Jan 1, 2014

By J. R. Giegerich

THE problem of dust control in metal mines has, of late years, received considerable attention. In 1932, a detailed study of dust conditions at the Sullivan mine was undertaken and, while there are no actual data available regarding conditions prior to that date, there has unquestionably been a great improvement as a result of the investigation and of the preventive methods adopted. In attacking the problem, three main factors were considered: first, and most important, how to prevent dust from being formed; second, how to depress or collect it if formed; and third-if unable to accomplish these-what precautionary measures must be adopted to prevent inhalation of this dust. Seven distinct methods of dust control are now practised at the Sullivan. Six of these are employed underground; they are tabulated below in the order of their relative importance. The seventh method is used in the crushing plants on the surface. (1) Improved ventilation (2) General use of water sprays and atomizers (3) Curtailment of secondary blasting during shift hours ( 4) 100 percent wet drilling-primary and secondary (5) Wearing of protective equipment (6) Change from carbide to electric lamps (7) Installation of dust collectors

Jan 1, 1936

By M. D. Griffith

"Ventilation models are a vital tool to ensure ventilation designs can provide airflow to all work areas in a mine. Airway resistance and variations in natural ventilation pressures will affect simulated airflow and heat distribution through a mine. Validating ventilation model resistances and pressures to the exact underground conditions can be difficult and the variances can contribute to significantly different simulation results depending on the structure of the ventilation design. The study will use sensitivity analysis to explore examples of variability of simulated airflow due to small resistance, heat and natural ventilation changes and thereby help the user identify both trustworthy and potentially unreliable parts of a mine ventilation model. INTRODUCTION Mine ventilation network modeling is a vital tool for ventilation professionals and has become increasingly relied upon during the design and operation phase of mine ventilation systems. However, they provide only an approximation of reality, and caution must always be exercised when drawing conclusions or making decisions based on simulated data. Ventilation modelling should be performed by persons with a sound fundamental knowledge of ventilation and ideally should be validated with field data, but in large mines, or mines which are yet to be mined, accurate input of the simulation variables can be difficult, and errors and inaccuracies may be difficult or impossible to avoid. This study discusses and investigates the sensitivity of the mine ventilation simulation results to input errors. In addition, there are limitations to what steady-state airflow and heat simulations can model, regardless of the accuracy of the model inputs. In some situations, steady-state solvers cannot capture the dynamic changing behavior of a ventilation system. This study will also describe and apply techniques to analyze the natural variability of mine conditions on ventilation models. The consequences of poor accuracy in some parts of a mine model may impact on the health and safety criteria of ventilation designs. For example, if an airway is required to flow in a particular direction and quantity, then despite a ventilation model showing correctly designed conditions, small errors in input values may result in incorrect prediction of the direction or quantity of airflow. This may create unexpected buildup of heat or gases during operational activities, causing safety issues or operational delays. The ability to know which parts of a mine ventilation model have increased potential for poor simulation results will allow engineers to consider the ventilation design and make changes if required to better guarantee the required design flows."

Jan 1, 2019

By A. C. Halferdahl

The Granby ores may be divided into three groups or classes. The No. I ore is a heavy pyrite, chalcopyrite, pyrrhotite, sulphide carrying some free silica, and calcite. No. 2 ore carries the same general group of sulphides as does No. 1, but in a lesser amount. The gangue is an altered greenstone. No. 3 ore has a smaller amount of sulphides than either of the others. Analyses of these ores is as follows: Cu. Si02 Fe. CaO S. Al 203 MgO No. I. Per Cent. 1.8 17.5 33.0 5.7 34.5 2.3 1.3 No. 2 Per cent. 2. 0 35. 6 23. 9 4. 3 I .5. 0 9. 2 6 .. 0 No. 3, Per cent. 1 . 5 40. 9 21 . 7 3. 0 I 1 . 3 11 . 0 5 . 4 The sulphide minerals in No. 2 and No. 3 ores occur largely in bands in the gangue, and for these portions comparatively coarse grinding serves to release the gangue. Drill cores show a certain dissemination of sulphides in portions of the rock, so that grinding to 5 per cent. + 65 mesh with 65 per cent.-200 mesh liberates the sulphide minerals very completely. The association of the sulphides is fundamental. The pyrite was probably deposited first and was followed by a portion of the chalcopyrite, or these two portions of the sulphide minerals were deposited together.

Jan 1, 1924

By Stephen G. Hardcastle

Worldwide, metal mines are going deeper. For example in Canada there are six such mechanized mines planning production at 3000m (10,000?). Working at such depths challenges all aspects of mining including the provision of ventilation to supply an equitable working climate for personnel and machinery. This paper explores the overall challenges of supplying ventilation in Canada?s deepest mines and how the volumes required could be minimized. This is essential because it must be remembered that ventilation and refrigeration are not only costly items to supply, but the magnitude of their cost is also very sensitive to the volume supplied. For ventilation this is obvious because of the cubic relationship between volume and cost. In deep mines, the main function of ventilation is the removal of heat transferred from the strata and generated by the mining machinery, and the air volumes supplied are designed accordingly. The second consideration is the removal of other pollutants that could be harmful to humans such as diesel and explosive fumes. However, the need for ventilation at its present design levels could be reduced. This paper discusses the implications of such technologies as: teleremote mining and alternatives to diesel equipment on the magnitude of the volume supplied; ventilation-on-demand which recognizes ventilation as a costly and limited resource; plus other aspects, such as the benefits of controlled recirculation, local cooling, and heat rejection back to the strata to gain further advantage from new developments. Furthermore, this paper advances the need to be able to design ventilation systems more cost effectively and how such new advances as process simulators can be used in conjunction with ventilation simulators to explore the diverse options that could affect the air volumes required and provide more realistic economic data upon which to base design decisions.

May 1, 2003

By P. Simon, G. Falkinger, G. Angerer, B. Gerold

"This contribution presents an investigation of the evolution of shrinkage pores during hot rolling with a special focus on the microscopic mechanism. The reliable closure of pores, which inevitably occur during the casting process, is of crucial technological importance for high-quality hot rolled plate products. Therefore, lab-scale tests were carried out under different typical thermomechanical loadings. Extensive data from optical microscopy was collected before and after deformation. The analysis shows that the average volume of pores evolves similar to the volume of an idealized arrangement of voids in an ideally plastic matrix. The average shape of the shrinkage pores, however, was found to be almost constant during deformation. Even though individual pores exhibit complex morphologies far from any idealized geometries, the overall evolution of a large number of pores is well captured by simple assumptions. In addition to the quantitative analysis, a schematic representation of this counter-intuitive behavior is provided. A simple ‘Gurson’-type void evolution equation was implemented in a three-dimensional Finite-Element model of the industrial hot rolling process. With the help of this mechanism-based process simulation the thermomechanical closure of shrinkage pores during the rolling process has been optimized for a variety of plate products.INTRODUCTION Aluminum alloys of the 7xxx series are widely used in the aircraft industry. They have to meet high quality standards regarding microstructure as well as mechanical properties. For hot-rolled aircraft plates, one of the most important quality requirements is that they are free from pores. Pores, however, are inevitably created during the casting process either due to shrinkage or due to the dissolution of gas from the melt. The pores have to be closed mechanically during the hot-rolling process. Therefore, the mechanism of so-called pore closure or void closure has a high technological relevance for the production of aircraft plates. The behaviour of voids in a ductile matrix subjected to mechanical deformation has been extensively studied, especially in the context of damage mechanics. A recent review (Besson et al., 2010) on modeling methods for ductile damage gives a good impression on how much experimental as well as theoretical effort has been dedicated to the problem of void evolution under mechanical loadings. Although void closure has been studied to a far lesser degree, it obeys to the same general theoretical evolution laws as void growth. The most basic theoretical result is that hydrostatic pressure drives void closure, while hydrostatic tension leads to void growth. The mechanism of void closure depends on the void shape. This is illustrated by the example of a flat penny-shaped void, which under compression obviously closes much faster than a sphere with the same volume. Theoretical models have been developed for the evolution of simplified void geometries, such as spheres or cylinders (e.g. Gurson, 1977), spheroidal (Gologanu et al., 1997) and ellipsoidal voids (Ponte-Castaneda, 1994). In industrial cast ingots, however, the pores exhibit very complex morphologies, which are far from any idealized geometry. X-ray tomography revealed ‘tortuous’ voids in a 5xxx aluminium alloy (Chaijaruwanich et al., 2006)."

Jan 1, 2018

By S. Dominguez, E. Gebrehiwot, S. Richardson, S. Sandoval

Copper electrowinning/electrorefining (EW/ER) is powered by direct current (DC) rectifiers that typically generate 30,000 to 70,000 amps and a bus-bus voltage of 200 to 500 volts DC. Tankhouses are designed so that DC current flows through “cell lines” which contain individual EW/ER cells electrically connected in series. Electrolyte composed of copper sulfate and sulfuric acid in water forms the “liquid conductor” that connects the metallic conductors in this circuit. In this setting, stray current is a DC current that strays from and therefore bypasses the tankhouse circuit by finding a path to ground, often through the electrolyte in pipelines that feed into and discharge from the cells, or through dried electrolyte (i.e. sulfate), which is also electrically conductive. Tankhouse workers can be exposed to shock hazards if they become part of a stray current path to ground. This presentation details examples of stray current shock hazards in electrolytic tankhouses and provides voltage and amperage measurements associated with stray current in these examples. A review of critical safety controls in EW/ER tankhouses that will mitigate the risk of employee shock from stray current is also provided. INTRODUCTION Electrolytic tankhouses are designed to deliver relatively large amperages of DC current to a series of electrolytic cells in which copper is plated out of solution using the classic anode-cathode pair geometry within each cell. Electrolyte is the “liquid conductor” that transfers current in between the metallic conductors of the cell. The metallic conductors include inter-cell copper bus bars and the anodes and cathodes themselves. It is sometimes forgotten that electrolyte as a conductor is capable of delivering DC current outside the designed circuit of a tankhouse. Stray current is a DC current that strays from the tankhouse electrical circuit by finding a path to follow other than the designed path. Safety becomes a concern when there is a risk of an employee becoming part of an accidental stray current path, thereby suffering an electrical shock. In 2016, Freeport-McMoRan (FMI) suffered a fatality at one of its copper electrowinning tankhouses. The forensic analysis concluded that stray current from the tankhouse rectifier contributed to the fatality. An employee accidentally fell into contact with a metal flange at the end of an HDPE pipe that was collecting cell overflow electrolyte from the tankhouse. DC current passed through the employee to ground, creating a shock that was judged to contribute to his death. The situation was exasperated because the employee was unconscious, and therefore was exposed to the stray current for several minutes before being found. In addition, the employee’s clothing was saturated with liquid, and the employee was found kneeling in puddled liquid on the ground. FMI immediately began an investigation into the root cause of the stray current that was measured at the scene. Sufficient electrolyte had accumulated in the HDPE pipe such that a continuous path was formed between it and electrolyte that was continuously overflowing from energized electrowinning cells. The metal flange on the pipe was the metallic conductor that carried the current to the employee from the electrolyte inside the pipe. Current then flowed through the employee to ground. Because of this incident, FMI undertook an extensive review of the hazards of stray current in EW/ER. FMI’s tankhouse workforce received a Tankhouse Electrical Safety training course developed in- house to insure worker understanding of stray current hazards. Tankhouse design changes were implemented to better insulate workers from stray current. Personal protective equipment (PPE) standards were also reviewed and changes made.

Jan 1, 2019

By E. A. Morris

It has been shown that Alberta oil-sands fluid coke can be effectively used to reduce SO2 to elemental sulphur while simultaneously producing sulphur-impregnated activated carbon (SlAC). In the capture of mercury from industrial flue gases, SIAC has proven to be a highly effective adsorbent material. The current research aims at developing an existing SlAC technology to meet the needs of copper smelters for mitigating both mercury and SO2 emissions, while making elemental sulphur as a co-product. The challenge behind this undertaking is that these flue gases generally contain percent levels of 02 and H20 vapour (2-12%). The focus of this study is therefore on the feasibility of reducing SO2 using fluid coke under copper smelter flue gas conditions, as well as the optimisation of SIAC properties for capturing vapour phase mercury. It is hypothesised that mercury capacity is strongly affected by the 02 potential of the activation gas due to changes in surface sulphur types arising from different reduced sulphur species. To verify this, gas chromatography is used to analyse the reaction products while XPS and XANES will be used to describe the nature of sulphur on the SlAC surface. CVAFS analysis of mercury capacity will finalise the hypothesis assessment. Preliminary results indicate that 02 at 5% does not play a significant role in SSA or pore development. As expected, increased residence time contributes to SO2 reduction and elemental S yield.

Jan 1, 2007