Search Documents

By R. L. Christie

"THE ISLANDS lying north of the Canadian mainland, and the large Boothia and Melville peninsulas, form one of the great archipelagos of the world; this sparsely vegetated and nearly unpeopled region extends about 1,500 miles east to west and 1,200 miles from the mainland to the northern tip of the northern-most island. Sea access to most of the islands is restricted by ice to the summer season, and the 'polar pack' ice of the Arctic Ocean presses the year round against the northwest margin of the archipelago. Although the region is remote, the accessibility has greatly increased through a network of weather stations, airfields and air routes connecting with southern centres.The area considered in this paper is that part of the island region underlain mainly by sedimentary rocks. In broad terms, this includes the land and sea areas of the archipelago and the adjacent continental shelf, but excludes the dominantly 'Shield' terrain of Baffin Island, and of Melville and Boothia peninsulas. An impression of the size and potential of this sedimentary region may be gained by comparing some areas: the land area of islands underlain mainly by sedimentary rocks is over 300,000 square miles or about 50,000 square miles greater than the area of Alberta. The total area of the region, including the continental shelf and the inter-island areas, may be double this figure, and may approximate one-seventh of the land area of Canada."

Jan 1, 1970

By G. F. Round

In order to obtain values of angle of shearing resistance and initial resistance for McMurray oil sand for use in general design calculations, the shear strength of this oil sand was measured in a controlled strain type tester, modified so that the rate of deformation could be varied between 0.01725 and 0.1869 inches per minute. Effect of temperature was investigated by adapting the equipment to operate at both 71 ° and 185 °F. The data are reported in terms of angle of shearing resistance and initial resistance for varying rates of deformation, composition and temperature. While the main sets of results reported here were obtained at a bulk density range of 108.7- 109.5 lb. / cu. ft., some results were obtained at a bulk density range of 101-102 lb. / cu. ft. Analysis of varance tables have been drawn up from the results obtained from least squares correlations and significance tests applied. It was concluded that oil content and temperature were significant variables for the degree of shear strength developed by the oil sand; increase of oil content and decrease of temperature each cause an increase in shear strength. The bulk density range 108.7 to 109.5 lb./cu. ft. gave angles of shearing resistance from 30° to 40° and initial resistance values of 0.37 p.s.i. to 0.85 p.s.i. For the bulk density range 101 to 102 lb. / cu. ft., lower values of shear strength were obtained, indicating that compaction density was also of importance

Jan 1, 1960

By E. Herrera, L. Mariscal

"Ilo Copper Smelter operates since 2007 with an ISASMELTTM furnace as a single smelting unit (1,200,000 tpy) associated with two Rotary Holding Furnaces for separation of matte and slag, and which directly produces a discard slag. Southern Peru continually has been improving the slag chemistry of its ISASMELTTM furnace in order to reduce copper losses, given its big economic impact due to large slag mass generation. The present paper describes the influence of the CaO, Al2O3 and magnetite content in the slag of the ISASMELTTM furnace correlated with the SiO2/Fe ratio and its liquidus slag. Also it defines the best slag chemistry and operating practice in order to reduce the copper losses without compromise the bricks life of the furnace.INTRODUCTIONIlo Copper Smelter of Southern Peru (Grupo Mexico) is located on the southern coast of Peru, and treats mainly copper concentrates produced in its own mines (Toquepala and Cuajone).The modernized smelter was commissioned in 2007 and operates with an ISASMELT™ furnace as a single smelting unit (1,200,000 tpy), which is associated with two Rotary Holding Furnaces (RHF) for separation of matte and slag. This slag is directly sent to the dump. Figure 1 shows the smelter flow diagram.The ISASMELT™ process is a bath-smelting process using a single lance. The lance tip is immersed into a molten slag bath contained within the stationary, vertical, refractory-lined ISASMELT™ furnace. The injection of oxygen-enriched air, through the lance into the slag results in a highly turbulent molten bath. Feed material falling into the turbulent bath from above reacts rapidly, resulting in extremely high productivity for a relatively small bath volume."

Jan 1, 2012

By V. Vorontsov

Catalysts Mo-Ni-S were prepared by combining MoS2 and NiS in weight ratios 1:1, 1:2, 1:4 and 2:1, each of which was admixed with 5%wt Ag and 5%wt YSZ to increase three-phase boundary surface area of the electrode. For comparison catalysts comprising Co-Mo-S in weight ratio of 1:1 of CoS to MoS2 admixed with 5%wt Ag and YSZ and pre-sulfided NiMoO4 were made. The catalysts were examined for electrochemical oxidation of hydrogen sulfide in solid oxide fuel cells (SOFC) at 850°C temperature. The catalyst prepared from 1:1 (wt. %) NiS:MoS2 demonstrated highest performance. Current density up to 1,330 mA/cm2 and power density up to 300 mW/cm2 were achieved using pure H25 gas, which are the highest among the reported H2S-powered fuel cells ever published in the literature. Anode materials of different NiS:MoS2 ratios have been characterized by means of X-ray diffraction (XRD), simultaneous TG/DSC analysis and Neutron Activation Analysis (NAA). TG/DSC and NAA results show that addition of NiS and Ag increases fuel cell performance due to improved structure/integrity of the anode. It has also been demonstrated that MoS2 is a suitable anode material in H2S-powered SOFC, with high activity towards H25 oxidation and thermally and chemically stable up to 850°C.

Jan 1, 2005

By D. Groenveld, M. Rozou

"Recent trends move towards automation, smart sensors, internet of things, powerful DCS, and more data. Are those trends already utilized in a real time production environment? Today operators still have to monitor several complex processes at the same time and predict their behavior based on an overwhelming amount of data available.The fact of the operator being overloaded and humans being unable to process multivariable problems shows the need of a tool merging essential data and providing consistent, sound decisions for long-term profitability.This paper shows a successful execution of ABB’s process improvement services in Aitik (Boliden SA), a copper mine located in Sweden. Soft sensors, fuzzy rule blocks and model predictive control were seamlessly integrated in the control system of the grinding area, resulting in proper control of mill loads and particle size without violation of any constraints.INTRODUCTIONDepending on the ore characteristics and the targeted plant capacity, the design of the grinding circuit may vary significantly. Typically, the circuit consists of several mills (rod, ball, SAG, AG) in series and/or parallel with a number of classifiers and sumps at appropriate locations. The goal of the grinding section is to reduce the ore particle size to a level that enables efficient separation between gangue and precious metals in the subsiding processing step. The trade-off between quality and quantity has to be made. It is also crucial to execute this process step at the lowest possible energy and grinding media consumption.An optimal grinding process controller must manage to maintain a given fresh feed level while keeping the product size within a given range without violating any constraints such as power, torque or load limits. To accomplish the aforementioned, it is necessary to manipulate the ore feed rate, water feed rate and the mill speed. The most significant disturbances adding another degree of complexity to this control problem are ore hardness and the amount of circulating load."

Jan 1, 2016

By T. S. Smith, C. C. Rennie

"THE LEAD-ZINC and tungsten mines of Canadian Exploration Ltd are on Iron Mountain, 8 miles south of Salmo, B.C., in the Nelson mining division. Relative location of the mines is shown on the general plan.First recorded lead production was in 1908 from surface outcrops. Small amounts of high lead ore were mined intermittently until 1926. No major lead-zinc production occurred until 1949 when outcroppings on the south side of the mountain were mined and diamond drilling began to prove the existence of a large replacement orebody. Lead-zinc ore has been mined continuously from the Jersey orebodies since March 1949, with monthly tonnage as high as 50,000 tons per month, but currently averaging 30,000 tons per month.Schee1ite-bearing tungsten ore was found in 1942 by H. Lakes in an old adit and open cuts at the north end of the Emerald tungsten orebody. The Emerald tungsten mine was developed by the Federal Government as a Wartime Metals project and operated for eight weeks in the fall of 1943, when the poor demand for tungsten closed the mine. Canadian Exploration Ltd. purchased the mine in 1947 and mined in excess of 100,000 tons in 1947-48 until the demand for tungsten dropped again and interest was centred on lead-zinc. The Federal Government repurchased and reopened the Emerald Mine in 195 L and built a new concentrator. The mine and mill were sold back to Canadian Exploration Ltd. in 1952.Regional Geology and IntrusivesThe host rock for both the lead-zinc and tungsten mineralization is the Laib formation of Lower Cambrian age, which consists of 400 feet of crystalline limestone underlain by beds of argillite, and argillaceous limestone locally altered to ""skarn"" or ""tactite"". The Laib limestone is overlain by black argillite and underlain by the Reno quartzite of Pre- cambrian age. Repetition of folded beds has allowed the interpretation of the large isoclinal fold which repeats the limestone (see general cross-section). Dolomitization and the associated lead-zinc ore have been found only in the right-side-up limestone and are not known in the overturned limestone.Two elongated stocks of granite cut the sediments. The Emerald stock outcrops along the east side of the Emerald tungsten mine and again west of the Jersey workings, while the Dodger stock outcrops only at the north end of the Iron Mountain. The shape and attitude of these bodies are believed to have been governed partly by pre-granite faulting and partly by pre-granite folding of the sediments. Although some forceful intrusion may have occurred the detailed granite surface indicates a gentle stoping emplacement."

Jan 1, 1949

By A. G. Eccles

Western Mines' milling circuit produces three concentrates (copper, lead and zinc), with the tailings being disposed of at the bottom of Buttle Lake. In view of the mine's location and the method of tailing disposal, a comprehensive pollution control program has been in effect since start-up. Changes -in the ore over the past few years have required the use of increasing quantities of sodium cyanide in order to effect a good copper-lead separation. This led to the use of alkaline chlorination for destruction of ?residual cyanide and precipitation of dissolved copper contained in the tailing effluent. The development of Western Mines' alkaline chlorination plant is discussed in detail, including initial test work and the evolution of procedures leading to the present operation. The current monitoring program is also reviewed.

Jan 1, 1977

By Kevin J. Melong

"Redpath Canada Limited and joint venture partner Thyssen Mining and Construction Canada have recently completed the sinking of the Scissors Creek service in Saskatchewan through its joint owned company, Associated Mining Construction (AMC). The Scissors Creek service shaft was sunk at Nutrien’s Rocanville mine. The following paper outlines the shaft sinking plant and the methodology related to sinking and shaft lining. KEYWORDS Hydraulic shaft jumbo, Hydraulic shaft mucker, Potash shaft sinking, Shaft lining, Sinking galloway INTRODUCTION The sinking and lining of shafts at mines to access mineral deposits has always been one of the great mining challenges for owners, engineers and contractors. Over the course of history in Canadian mining, the sinking of potash shafts through the notorious Blairmore formation of Saskatchewan has proved to be some of the most challenging shaft sinking projects on record. There is no doubt that today’s shaft sinking business demands the utmost in safety performance while delivering projects within schedule and budget. Given these requisites, Redpath and TMCC (executed under the joint venture company, Associated Mining Construction or AMC), were taxed with developing the shaft sinking system to deliver this program in the safest and cost effective manner, with due regard to schedule and quality. Traditionally the potash shafts sunk in Saskatchewan involved a significant level of manual labour, owing to the methodology of excavation by means of chipping the frozen shaft sections with hand held pneumatic machines, and manually placing tubbing segments or steel liners of the shaft lining system. Most certainly, the AMC team wanted to make a step change from those earlier sinking programs and develop systems for sinking this potash shaft that removed the high level of manual work, thus making this project inherently safer, while endeavoring to sink more efficiently. With that in mind, the team embarked on a design program to improve its overall shaft sinking systems without the requirement for excessive capital and methodology flexibility to adapt to potential changing conditions expected to be encountered during shaft sinking. This was especially important should the new approach be met with less than expected success, and retrofitting of the system was required. The concepts were developed to provide for a much improved work environment, while easing the manual labour burden on the workers with innovative equipment and approach to the work."

Jan 1, 2019

By M. Sengupta

International trade in minerals plays a very important role in the economic growth of many nations. Several less developed countries a1•e heavily dependent on their mineral exports for earning foreign exchange, which is needed for industrialization. Mineral exporting nations experience many problems in international mineral markets; the most important are tariff barriers, deteriorating terms of trade, instability in metal prices, etc. The formation of international mineral cartels to raise prices can be successful only to a limited extent and only for a short period of time.

Jan 1, 1976

By D. Gagnon, B. Dubreuil, J. -M. Lalancette, D. Lemieux

"The pilot scale extraction of gold with a brine of sodium chloride and bromide at 30 ºC, in an atmosphere of halogens at atmospheric pressure, leads to gold chloride with 95% gold recovery. The use of dilute hypohalites (1 – 3%) instead of free halogens, which is strong enough to oxidize hypobromite into bromine, simplifies the recycling of halogens by electrolysis. With the recycling of water and brine, the regeneration of hypohalites and with a barren solid that is inert and stable. The Nichromet Extraction technology is a green process where the protection of the environment does not preclude profitability.INTRODUCTIONThe use of chlorides for the extraction of gold predates the discovery of chlorine by Scheele in 1774. In the Plattner chlorination process (Christy, 1888) sodium chloride and copper salt were used to promote gold recovery by amalgamation with variable results. The introduction of the cyanide technology in 1889 has led to a general use of this method for gold recovery. In the last decades, a return to chlorine in extractive processes has been noted (Ferron, Fleming, O’Kane and Dreisinger, 2002), mostly because of environmental pressure for non-cyanide technologies.This paper describes a closed circuit proprietary approach (Lalancette, 2009) developed and piloted by Nichromet Extraction Inc. for the extraction of precious metals with recycled mixed halogens; chlorine and bromine from hypohalites. DESCRIPTION OF THE PROCESSThe attack of gold by halogens can vary significantly. The rate of reaction is substantially higher with bromine (Br2) than with chlorine (Cl2), by a factor of more than five, although the oxidation potential of Cl2 is higher than Br2, as shown in Equation 1a and Equation 1b (Latimer, 1952)."

Jan 1, 2012

Introduction A Hypothetical Scenario: Suppose that your company's research department has developed a new device which represents a significant innovation. You would like to begin selling it as soon as possible. The new device has not been publicly disclosed. You're not sure about what type of intellectual property protection you should be seeking, or when you should be seeking it. As discussed below, assuming that the costs are worth it, a patent application probably should be filed before any public disclosure is made. In general, if you do not file a patent application prior to a public disclosure, you will lose rights. Major Types of Intellectual Property In this paper, intellectual property protection is broadly discussed. Practical steps which can be taken to minimize the possibility of losing intellectual property rights (and maximizing the possibility of benefiting from your company's intellectual property) are outlined at the end of this paper. The issues discussed in this paper are somewhat complex, because a number of outcomes are possible, depending on the facts. It is strongly recommended that you seek legal advice in your jurisdiction in connection with any particular circumstances relating to intellectual property rights. "Intellectual property" refers to a number of different types of rights. The major types of intellectual property are: (i) patents; (ii) trademarks; and (iii) copyright. Trade secrets are also usually considered to be a type of intellectual property, and they are also discussed in this paper because of their importance. In general, each of these types of intellectual property protects different subject matter, although there can be some overlap. Intellectual property rights are generally territorial in nature. The scope of protection of a type of intellectual property in a country (e.g., patent protection) depends on whether the specific national requirements for protection have been met.

Feb 1, 2008

By Haipeng Li, Jacob Masliyah, Barun Gorain, Jian Huang, Qingxia Liu, Zhenghe Xu, AuTec Innovative Extractive Solutions Ltd.

"Froth flotation is widely used to selectively separate one or more minerals from an ore over a wide range of particle sizes with high efficiency. Bubble–particle attachment is one of the most critical steps in flotation. The objective of this project is to demonstrate the need for an innovative dual bubble generator to improve flotation efficiency. This dual bubble generator was designed to generate two different sizes (micron size and typical flotation size) bubbles. The micron size bubbles generated on the crevices of particle surfaces in venturi type of cavitation tubes enhanced the attachment of fine particles to the bubbles in conventional flotation systems. They also acted as a secondary collector, which has the potential to reduce operation cost and improve flotation recovery. The dual bubble generator was evaluated for a double refractory gold ore with 3g/t Au, 1.5 wt% TCM (total carbonaceous matter) and 0.7 wt% sulfides. The results were compared with those obtained using a commercial bubble generator. Compared with the commercial bubble generator, the dual bubble generator showed not only a higher gold recovery, but also an improved separation efficiency, demonstrating the potential of dual bubble generator in fine particle flotation.INTRODUCTIONFroth flotation has been widely used in mineral processing and waste water treatment. However, flotation has been proven inefficient for fine particle recovery although it becomes increasingly inevitable to process fine particles with the depletion of easy processing ores. The critical problem of fine particle flotation is the low attachment of fine particles to flotation size bubbles due to their low collision rate. Based on a commonly acceptable flotation model given by R =F*[Pc*Pa*(1-Pd)], the probability of bubble–particle collision (Pc), attachment (Pa) and particles detachment from air bubbles (Pd) collectively determines fine particle recovery (R) (Yoon and Luttrell, 1986). Since Pc = (3Dp/Db) where Dp and Db are diameters of particles and bubbles, respectively, bubble size and particle size impact the bubble-particle collision in opposite directions. It is evident that the probability of bubble–particle collision decreases with decreasing the size of particles, leading to a low recovery of fine particles. In this case, reducing the bubble size and/or increasing the apparent size of particles by fine particle aggregation are clear means to improve fine particle recovery."

Jan 1, 2016

By Guy Demers

"This paper defines the responsibilities and functions of the Maintenance Department, and its organization, physical and human assets, highlighting the unique operating problems. Due to the self-sufficient aspect of the Asbestos Hill Deception Bay project, the Maintenance Department cover-s fields that are numerous and very dissimilar: production, mobile, processing, service, power generation, fire protection, heating, water and sewage disposal equipment. Added to this, buildings, plant and camps, wharves and communications equipment all demand versatility, adaptability and expertise from maintenance personnel. Good maintenance practices are a necessity in this environment and are more critical than at southern locations; that is, high-quality replacement material, complete and well-controlled preventive maintenance, major repairs on a component-replacement basis, updated inventory, efficient training and permanent contacts with suppliers, combined with an equipment improvement program, updated specifications on lubricants, hoses, seals, filters, etc., are mandatory. The seasonal aspect of the operations applies a great deal of pressure on the maintenance team, as the production months do not permit major repairs. Short- and medium range planning and accurate evaluation of equipment conditions highly influence production efficiency. Maintenance control, planning and scheduling do not follow the accepted standard routines, as personnel turnover normally does not permit an accumulation of knowledge of the equipment history and condition by the •individual tradesman."

Jan 1, 1976

By R. Mulligan

"The Cordilleran tin belt extends from the Seward Peninsula in westernmost Alaska to Mexico. Throughout the Canadian section, tin occurrences are mainly confined to a belt along the northeastern fringe of the Western Cordilleran sub-region; the boundary of this sub-region with the Eastern Cordilleran sub-region is most simply defined as the practical eastern limit of granitic and metamorphic rocks. The stratified rocks underlying this restricted belt are mainly late Precambrian and early Paleozoic miogeosynclinal sedimentary rocks, which are more or less metamorphosed but otherwise are generally equivalent to the less severely deformed rocks underlying the Eastern Cordilleran sub-region. They contrast with Late Paleozoic - Mesozoic eugeosynclinal volcanic-sedimentary assemblages farther west, but the granitic intrusions throughout are mainly of Late Mesozoic age. Thus, narrowly defined, the tin belt largely coincides with a lead-zinc-silver metallogenic province, whereas copper deposits characterize the eugeosynclinal regions to the west. In addition to the tin occurrences, which include the Sullivan lead-zinc-silver mine, Canada's only significant producer, the belt contains all the beryllium, most of the tungsten and many Iithophile-type molybdenum occurrences. Several types of occurrences of each metal are represented. Lithium occurrences in the Canadian Cordillera are notably rare, and these few are insignificant."

Jan 1, 1971

By W. H. Fertl, S. J. Pirson

Well logging techniques, as used successfully in oil and gas exploration, can also be used to give a detailed evaluation of drill holes through industrial mineral deposits such as sulphur. This paper describes the logging tools used gives the theory behind the well-log interpretation and discusses the application of the method in sulphur-bearing limestone and m more complex sulphur deposits.

Jan 1, 1970

By H. Lachmund, R. Bruckhaus

At Dillinger Hüttenwerke/Germany steel production of grades for linepipe applications especially for sour service has a long tradition. The BOF process after replacement of the vessels is optimized by a newly developed lime addition model and variations in lance tip geometry. Equipped with three state-of-the-art VOD tank degassers metallurgical requirements of lowest contents of e. g. sulphur, nitrogen and hydrogen can be achieved. Three continuous casting machines of vertical bending type with solid core even improve already high levels of cleanliness. The vertical part corresponds to the metallurgical length of 12 to 15 m and therefore assures a maximum of cleanliness after solidification before bending. Slab thickness up to 400 mm can be produced with model controlled dynamic soft reduction. The accurate alignments of the casters assure minimized segregation and microporosity. Surface and internal cracks can be avoided by special cooling, bending and straightening strategies.

Jan 1, 2005

By T. Schepp, T. Friedrich

"The natural stage of deep mines operation is a closure of unnecessary shafts. It is extremely important to ensure a proper shaft closure to avoid stability loss and the associated damage to surface facilities in the future. For the still active shafts, it can be done by a dedicated shaft closure design, but even then, depending on the shaft closure method, it may be necessary to perform regular shaft inspections. The paper presents a short overview of shaft closure methods and available tools and devices developed in the last time for such shaft inspections. INTRODUCTION The natural stage of deep mines operation, commonly occurring after depletion of the reserves of mined materials, is a closure of unnecessary shafts. All over the world, the number of liquidated shafts grows continuously and the problem of shafts disposal is especially critical for deep shafts. The typical depth of 600 m of currently liquidated shafts in Poland may already be seen as a challenging task. The greater is the challenge of shaft closure in Germany where the last active coal mines for shafts with a depth of up to 1,300 m have been recently closed. It is therefore extremely important to ensure a proper shaft closure to avoid stability loss and the associated damage to surface facilities in the future. For the still active shafts, it can be done by a dedicated shaft closure design, but even then, depending on the shaft closure method, it may be necessary to perform regular shaft inspections. In many cases, it is more important to inspect old, abandoned shafts, where the wall stability or even liner type are not fully known. SHAFT CLOSURE METHODS Abandoning a shaft is a complicated task, as shafts, being the link between the surface and an underground network of workings, disturb hydrogeological and gaseous conditions in the rock mass (Sztelak, 1991). Closure procedures at older mine sites have been carried out in accordance with earlier legislative requirements. For very old shafts (+100 years), it means in many cases only a sealing of the shaft entrances by means of timber or concrete slabs. In the 20th century, the shafts were also closed by means of filling with grainy materials, but even then the retrospective activities at abandoned mine sites were extremely limited and in most cases no further monitoring measures were performed. The possible consequence of an improper shaft closure and lack of monitoring is presented in Figure 1."

Jan 1, 2019

By Ross D. Lawrence

"Comparable transaction analysis is the best known of the market approaches to valuation of exploration-stage mineral properties. The analysis of option and farm-in agreements can also provide useful guidance to valuators. While such approaches can be distorted by incomplete analysis, market-based methods are capable of providing consistent, credible results when carried out carefully with due consideration paid to all factors which buyers and sellers consider when dealing in the real market.RÉSUMÉRoss D. Lawrence graduated from the University of Toronto with a B.A.Sc. (Applied Geology-1956) and an M.Comm. (Mining Finance-1959). As a student and following graduation, he worked across Canada on a variety of mineral exploration projects.In 1962, he was one of the founders of Watts, Griffis and McOuat, and has practiced as consulting engineer since then. For the past 20 years, Mr. Lawrence has headed up the WGM valuation practice, responsible for a group of professionals which has carried out scores of valuations of mineral properties and mining companies. He is a Certified Minerals Appraiser of the AIMA and an active participant in professional affairs.INTRODUCTIONMineral properties without defined resources present one of the most challenging tasks to the mineral valuator. You will hear from others at this conference about the use of cost and income approaches to the problem of valuing exploration properties. This paper will concentrate on market-based approaches. Market based-approaches are based on the principle of substitution and include such techniques as:??Comparable transaction analysis (sometimes referred to as sales comparison analysis).??Farm-in commitment analysis??Rules of thumbAre there any valuation standards available to assist the valuator? In Canada there are none that apply to the valuation of mineral assets or securities. This problem is being addressed, at least in part, by the CIMVal committee of the Canadian Institute of Mining, Metallurgy & Petroleum (CIM)1. Further, the recently established Canadian Association of Mineral Valuators will be giving consideration to the adoption of valuation standards."

Jan 1, 2003

By George S. Rice

Foreword Explosion hazards differ widely in the mines of different fields or coal basins. They also differ as between different mines in the same basin or fold, because of variations in gas entering the mines, and because dust conditions and explosion hazards are affected by the mining methods employed and the organization of the work. It is unquestionably true, however, that there are greater differences in explosion hazards in mines of different coal fields or basins than between different mines of the same field or basin. In these respects, the coal fields and individual mines in Alberta are not exceptional. The same conditions obtain in various countries where coal is mined, and are found in single States, as for example in Colorado, where coals are mined ranging in character from sub-bituminous to anthracite, and in attitude from flat horizontal to steeply pitching beds. The U.S. Bureau of Mines, at its experimental mine near Pittsburgh, Pa., has made large-scale tests of the relative explosibility of dusts of coals, ranging in rank from Wyoming sub-bituminous coal containing 19 per cent moisture, to anthracite from Pennsylvania, and including samples from a mine in the Crowsnest Pass district, B.C., and from a Vancouver Island mine. The Bureau has also made similar tests of the dust of coal from a Yorkshire mine which the British Safety-in-Mines Research Board uses as standard.

Jan 1, 1927

By J. F. Henderson

Stable mining operations commenced in the Northwest Territories in 1933. Pitchblende from Great Bear lake and gold from the Yellowknife district are the main minerals produced. The value of pitchblende products produced from 1933 to 1941 was nearly $6; 000; 000; data on subsequent production are not available. The first gold was produced from the Con mine at Yellowknife in 1938. Other properties that later came into production include the Negus; Slave Lake; Thompson Lundmark; and Ptarmigan mines. The annual gold production reached $3; 862; 000 in 1942 but due to the war and consequent labour shortage fell to $333; 218 in 1945. The only producing mines at present (May; 1947) are the Con and Negus; but several promising properties are under development; including that of Giant Yellowknife Gold Mines where large tonnages of ore are being blocked out. With the reopening of former producing mines and new production from properties now being developed; gold production should rapidly increase and exceed its former peak within the next few years.

Jan 1, 1954