Search Documents

By Shantanu Patel, C. Derek Martin

"The objective of this work is to develop a practical numerical approach for applying the confining pressure to discrete element cylindrical triaxial tests. A layer of membrane particles with very low stiffness and extremely high contact bond strength was created around the lateral boundary of the cylindrical numerical specimen. To prevent the membrane particles from penetrating into the rock specimen on application of confining forces and to provide a smooth boundary surface, the space between the membrane and rock particles was filled using small-diameter packing particles. The results of this method were compared with those of rigid boundary method with confining pressure of 20MPa. The results obtained show that new approach gives both peak strength and post peak response that are in closer agreement with laboratory findings. BACKGROUNDThe discrete element method (DEM) has become the cornerstone for simulating both intact material and discrete fractures for low porosity strong rocks (ISRM Classes R3 to R6). Despite the advances in its application, simulating realistic behaviour of intact rock using the DEM remains a challenge. The bonded particle model was introduced as a potential solution for simulating the complex mineral grains in strong rock and other granular materials (Potyondy and Cundall, 2004; Utili and Nova, 2008; Salot et al., 2009). While some issues were resolved, a remaining challenge is the lack of the bonded particle model to simulate the brittle response commonly observed in strong rocks during the triaxial compressive test. Such behaviour is shown in Fig. 1 for Lac du Bonnet Granite at a confining pressure of 20MPa."

Jan 1, 2015

By L. López

Argentina reported about 40,000 tonnes of uranium (tU) as reasonably assured resources and inferred resources for the production cost category <130 US$/kgU in the OECD-NEA/IAEA classification scheme. These resources belong to the following projects: Sierra Pintada, Cerro Solo, Don Otto, Laguna Colorada, Laguna Salada, Meseta Central and Amarillo Grande. With three heavy water reactors in operation and an approximate installed capacity of 1.7 GWe, the current natural uranium requirements are about 220–250 tU per year. Based on various nuclear growth scenarios, it is estimated that by 2030 there will be a generation capacity of some 3,092 GWe for the reference case, with raw material needs of some 486 tU per year. Currently, there are no perspectives for local uranium production in the short term, and it is thought that uranium projects with identified resources must complete resource delineation and advance in technical pre-feasibility studies for the recovery of uranium. It is expected that Argentina continue meeting the uranium demand with imports in the next following years. In the Latin America region, both Brazil and Paraguay could be considered as potential uranium suppliers. In conclusion, despite the apparent growth prospects for the use of nuclear energy to generate electricity in Argentina, there are no immediate prospects for the provision of uranium oxide concentrates from domestic deposits for fuel fabrication. This has implications for supply and energy security.

Jan 1, 2020

By Staff, G. M. Hogg

"The eastern portion of the Late Precambrian geosynclinal structure known as the Labrador Trough comprises a 16,000-square-mile sulphide-bearing belt of good potential as a base metal exploration area. Hollinger and Hanna mining interests have carried on exploration in the region since 1953, with encouraging results. This program has been considerable in terms of both effort and expenditure, and has resulted in an apparently successful primary evaluation of the entire belt.Much detailed work remains to be done in the area. Exploration to date has been largely of a reconnaissance nature, employing various methods in common use in Canada today. In the course of this work, several deposits of promise, containing near-economic quantities of copper, zinc, nickel and other metals, have been located. A broad classification of these deposits is proposed.Exploration in the sulphide belt was started on the basis of partial control of the area under mineral exploration concessions. This was necessary to justify operations in an area of difficult access and high operating costs. The results of this now-terminated arrangement are regarded as being of benefit to those directly concerned as well as to the mineral industry in general."

Jan 1, 1966

By J. F. Henderson

THE National Advisory Committee on Research in the Geological Sciences was established seven years ago - in 1949. In 1952, shortly after the Committee had really begun to function and had issued its first report, a paper ( l) was presented describing the objectives and organization of the Committee and the progress to that time. Another four years have gone by and the Committee feels a further progress report may be of interest. HISTORY Ten years ago, in 1946, the Geology Division of the Institute set up a Committee on Geological Research. This Committee, under the Chairmanship of Dr. J. E. Hawley, recommended that "a National Advisory Committ.ee on Research in the Geological Sciences be formed" (2). With the backing of the President and Council of the C.I.M. this recommendation went forward to the then Minister .of Mines and Resources and, with his approval, to the Committee on Scientific and Industrial Research of the Privy ?Council. As a result, the National Advisory Committee was set up in 1949.

Jan 1, 1956

By Earl T. Hayes

This paper briefly reviews the laws enacted in the United States governing the coal miner. It discusses amendments to the Coal Mine Safety Act and describes the provisions of the Metal and Non-Metallic Mine Safety Act.

Jan 1, 1969

By Shintaro Takamiya, Kazunari Yoshida

"Recently, small sized micro-needles for medical are required more frequently by patients. The biggest reason is that it presents great burden on the patients, due to the size of the needle injection. People need to use a very small needle to lower the pain, but the downfall is that it makes them more expensive due to their complicated manufacturing method. Therefore, we need to fabricate a needle by wire-drawing to decrease its price. Tube-drawing is beneficial for its production value; however, in conventional tube-drawing it is difficult of control the wall thickness of the tube and makes it 1mmor lower in diameter. That is why, we propose fluid-mandrel drawing for new tube drawing. This method allows fabrication of a fine tube by using the pressure of the fluid in the tube. In this research, the goal is the fabrication of a fine tube by fluid-mandrel drawing and its evaluation. Finally, the fabrication of a fine tube by fluid-mandrel drawing was conducted and in result a tube with a diameter of 0.2mm, high strength and thin wall and fine inner surface was drawn, which can be used as a lesser pain micro-needle.INTRODUCTIONThe main manufacturing method of the current medical needles is roll forming. With this method, it is difficult to make a tube with a diameter lower than 1mm. Deep drawing has been proposed and used as method to further reduce the diameter, but this method is costly and the injection needle obtained by this method is several times more expensive.Therefore, we need to obtain a fine medical needle by drawing process that can be mass-produced and inexpensively manufactured. However, with the conventional drawing process, it is not possible to obtain a syringe needle with a reduced diameter easily, that is why, a fluid-mandrel drawing has been proposed which can reduce the diameter without damaging the inner surface. The methodology of the method is, a fluid is filled in the sealed tube and the pressure inside the tube during drawing is responsible for the good inner surface and wall thickness. It is also expected that the fluid can be easily discarded and that the tube can be manufactured on a long scale."

Jan 1, 2017

By W. G. Schultz

"Sylvite's potash mine, which produces 8,000 tons of ore per day, probably ranks as one of the most highly mechanized and automated mining operations in the world. Employing, on a normal 10-hour production shift, one supervisor and a crew of seven operators, Sylvite is able to mine at an average rate in excess of 600 tons per hour. The ore is produced by two Marietta miners weighing 258 tons, the largest and heaviest pieces of equipment ever taken underground. The ore produced by these two Marietta miners is conveyed to the shaft area, cycled through a 15,000-ton storage system and hoisted to surface completely automatically. The operation of all equipment in the mine can be monitored and controlled from a central control panel located underground. Because Sylvite's mine is a new operation with equipment of a new design, the full potential of the operation has not yet been realized. The ultimate capability is clearly evident from the success Sylvite has had over the past year as the average mining capability has risen from 100 tons per hour to 600 tons per hour."

Jan 1, 1973

By J. V. Thirgood

"Reclamation legislation was introduced in British Columbia in 1969 amidst public concern and controversy. This paper reviews this legislation as it relates to coal mining, and how it is being implemented.Although the principles of land reclamation are reason-ably well understood, reclamation of industrial wasteland has never previously been attempted under such rugged conditions as occur in the Canadian Rockies and a new methodology is being developed.The resolution of the technical and organizational problems involved are discussed and the techniques and experiences described."

Jan 1, 1971

By S. Manning, W. Morris

Mineral exploration assessment file information has long been considered a useful resource for developing mineral exploration strategies, and one of the most common data sets fled in assessment reports is ground magnetic surveys. The new Earth Resources and Land Information System database (ERLIS) now provides a method for rapidly accessing all references to a specific area through a series of raster images. The ERLIS provides access to the Assessment File Research Imaging (AFRI) database which comprises geo-science mineral exploration assessment file data, Mineral Deposits Inventory (MDI), together with provincial aeromagnetic data from the Ontario Ministry of Northern Development and Mines(MNDM). Conversion of the raster images of ground geophysical data to vector data files together with the concatenation of grids from adjacent claims provides a method for constructing high resolution magnetic regional images. The value of this resource is demonstrated through the construction of a single composite magnetic image derived from eight assessment file grids for an area south of Kirkland Lake, Ontario, within Pacaud and Catharine Townships. The composite grid of magnetic data provides a map with resolution that is not achieved by currently available Ontario Geological Survey airborne data sets. Details contained within the new high resolution image, permit the differentiation of lithologies and their boundaries, fault orientations and the location of alteration zones with magnetic response.

Jan 1, 1997

"Real-time, on-stream analysis of the metal content of process slurries is an essential prerequisite for process monitoring and advanced control of mineral processing circuits. On-stream X-Ray Fluorescence (XRF) sensors for base metal applications are available commercially and form the basis of many plant monitoring circuits. To date, these commercial technologies have been insufficiently sensitive to measure precious metals such as gold and platinum group elements, typically present at part-per-million (ppm) and sub ppm levels. CSIRO has developed a novel X-ray based technology, called UltraGold, which enables detection of gold in slurries on a real-time basis with a precision below 100 parts-per-billion. This technology is based on the use of advanced X-ray optics, extensive Monte Carlo computer modelling for analyser design, high accuracy X-ray spectrum fitting where the X-ray intensities are matrix corrected. In this paper, we will introduce this technology and discuss the results of a proof of principle study performed in the laboratory with plant slurries (tailings and concentrate) from an Australian beneficiation plant. Finally, we will discuss further planned improvements. As projected grades in (gold) mining around the world fall and several large-scale mines approach the limits of their economic reserves, this method can enable significantly reduced operating costs by rapid analysis to improve circuit efficiency and hence improve recovery significantly.INTRODUCTION This paper describes a study undertaken to explore the feasibility of applying CSIRO?s UltraGold XRF technology to the on-stream measurement of gold in process slurries. The provision of rapid, accurate information of gold grade in feed, tailings and concentrate streams would facilitate significantly improved process control and early detection of plant upsets, resulting in substantial cost-savings. CSIRO have patented X-ray fluorescence (XRF) techniques for the analysis of key elements in slurries present at part-per-million (ppm) and sub-ppm levels. Conventional, commercially available on-stream XRF instruments generally have detection limits in the tens of ppm range, precluding their use for analysis of elements like gold that are mined and processed at much lower concentrations."

Jan 1, 2017

By Donald L. Mordell

Introduction A very large part of the world&apos;s fuel resources are in solid form, as various grades of ?coal, but an increasing proportion of fuel demands on this Continent and else-where are having to be met by liquid fuels. Convenience and, in many cases, cost weigh heavily in favour of the liquid: fuels, and there are many fuel burning applications where the use of coal would be impractical, such as for automotive or air transport. By extrapolating the present trends one might conclude that, in future years in Canada and the United States, coal will be used only in a few power stations close to coal fields. If such a state of affairs should arise, it will obviously prove embarrassing to those accustomed to make their livelihood from the winning and marketing of coal, but it is perhaps not so obvious that it must also prove an embarrassment to the nation. The major reasons for this are two in number. Firstly, if present coal production is to be replaced by oil production, a large capital expenditure is necessary, which must inevitably be paid by the consumer; and secondly, in times of emergency, large amounts of oil fuels are required for military purposes which cannot be achieved with solid fuels. It is obviously unwise, therefore, to discontinue the use of coal for those non-military jobs that it can do. If we examine the major fuel markets we find that there are three: Domestic heating Steam generation Transport by air, sea, and land For domestic heating, the extreme convenience of oil, in spite of its greater cost, has captured much of the coal market.

Jan 1, 1952

By Jeffrey T. McGinty, Frank M. Wheeler

Plant layout is the arrangement of equipment, process areas, departments, infrastructure, and support facilities. Plant logistics is the flow of parts, people, resources, and information throughout the production process. This chapter: outlines key factors and provides checklists to facilitate layout development; presents risk management approaches to test the logistics and functionality of alternative layouts; and uses real-world examples to illustrate effective simulation modelling to assess plant layouts.

Jan 1, 2015

By M. T. Ho, D. E. Wiley

The iron and steel industry accounts for almost 5 % of the total world CO2 emissions. Optimisation of the steelmaking process has led to significant reductions in the energy intensity to the point where it is now close to the thermodynamic limit. Further reductions are not likely to be achieved with efficiency improvement alone and will require the development of novel or breakthrough technologies. This paper will show the costs of implementing CO2 capture at direct atmospheric emission points for a number of iron and steel production processes. These include a conventional process, top gas recycling processes, the Corex and Hismelt smelt reduction processes and the Midrex direct reduction process. Depending on the point source emission, costs of capture with existing chemical absorption technology at iron and steel plants can be similar to capturing CO2 at pulverised coal fired power plants.

Jan 1, 2015

By John R. Sullivan, Real Daigneault, Mathieu Piché, Jayanta Guha, Gilles Bouchard

"RESUMELa stratigraphie du camp minier de Matagami se résume a la présence de deux groupes volcaniques: le Groupe du Lac Watson et le Groupe de Wabassee qui le surmonte. Les gisements de sulfures massifs volcanogènes sont situés au sommet du Groupe du Lac Watson. Ces roches sont déformées par l'anticlinal de Galinée dont l'axe, orienté E-W, plonge vers l'ouest. Le cœur de cette structure est occupé par le Complexe de la Rivière Bell.Les roches volcaniques du flanc sud de l'anticlinal sont peu déformées et pendent à 45° vers le sud. Les gites qui s'y trouvent présentent la morphologie typique des gisements de sulfures massifs volcanogènes. Ceux-ci se situent le long d'un horizon repère cherteux et sulfure, appelé ""Tuffite Clef', et leurs cheminées d'altération rejoignent, en profondeur, une zone d'altération stratiforme d'étendue régionale.Les roches du flanc nord ont été transposées tectoniquement en écailles chevauchantes, de dimension kilométrique, a l'intérieur d'un couloir de failles anastomosées d'orientation est-ouest. A l'intérieur: le ce couloir, les gites de sulfures sont déformes et sépares de leur héminée d'altération sous-jacente par des failles.Les gites de sulfures situes sur les deux flancs de l'anticlinal de 'Galinée se seraient mis en place dans un mime environnement volcanique. Leur position stratigraphique est identique puisqu' ils se 'rouvent au sommet de la rhyolite porphyrique du Groupe du Lac Watson. lis se seraient constitués au cours d'une pose volcanique recédant 1'éruption du basalte du Groupe de Wabassee. Le Complexe de la Rivière Bell est perçu comme la source de chaleur responsable de la circulation des fluides hydrothermaux qui sont à ""origine des gisements de sulfures massifs volcanogènes."

Jan 1, 1990

By John G. Ayttes

"The following is a review of the advance of raise boring and its current position. The viewpoint presented is that the mining industry, through its worldwide acceptance of raise boring, has acknowledged the success of the method in general. Acceptance, however, does not imply complete satisfaction with either the equipment or current operating costs. Therefore, a brief review of how boring costs are being r educed is presented, citing examples. Recent raise borer applications of special interest are presented to show adaptability of current equipment, and some special projects in the planning stage are highlighted."

Jan 1, 1972

By A. Ingelson

Conflict over mineral development and its impacts on indigenous peoples occurs in many countries around the world. Canada, Bolivia and Peru have experienced mine development for centuries in areas where indigenous communities have been and continue to be affected by the mining industry. On a global basis the mining industry continues to face the challenge of implementing meaningful consultation programs with indigenous peoples. Many governments around the world have adopted sustainable development as a policy and one important element of sustainable development is minimizing social conflict. John Moffet and Francois Bregha (Moffet & Bregha, 1996), in their analysis of the role of law reform in promoting sustainable development, noted that stakeholder participation can reduce this type of conflict. Social conflict can result in expensive litigation and costly project delays for mine developers. Meaningful consultation with indigenous peoples in areas where mine development is proposed can be a critical factor in securing a social licence to operate. A report released by the United Nations in 2005, outlined the elements of a concept called ?free, prior informed consent? (FPIC) that promotes more sustainable development. FPIC provides that mineral exploration and mining should not proceed unless the mining company has secured the consent of the relevant indigenous group(s). This paper employs a comparative approach to evaluate the extent to which three active mining nations, Canada, Bolivia and Peru, require consultation with indigenous residents and adhere to the principle of FPIC. The comparative approach assists in the identification of those consultation elements in the legal regimes of each country that can minimize social conflict in mineral exploration and mine development and therefore contribute to more sustainable development. First, we examine the legal requirements to consult with and accommodate indigenous communities in Canada, a country with a long history of mineral development over a large geographic area that has entrenched in its Constitution the protection of indigenous peoples? rights. We then turn to an analysis of Bolivia, one of the most indigenously conscious mining jurisdictions that has followed the Canadian lead in entrenching constitutional protection for indigenous peoples. Third, the approach to consultation with indigenous peoples in Peru, a nation that has not adopted the Canadian and Bolivian approaches to constitutional protection of indigenous peoples rights, is considered.

Aug 1, 2013

By J. A. Bossert

"In 1957, the Department of Mines and Technical Surveys (now Energy, Mines and Resources Canada) issued their first certificate for a fire-resistant conveyor belt. The testing procedure used was a combination of those used in the U.S.A. and the U.K. Subsequently, certification was granted to fire resistant electric cables (1974), fire-resistant mine duct material (1976) and fire-resistant hydraulic fluids (1978).Until recently, the testing procedures were copied from either the U.S. or the U.K. However, since the founding of the new Canadian Standards Association (CSA) Steering Committee for Electrical/Mechanical Mine Safety in 1981, these requirements have come under the close scrutiny of new CSA technical committees who will attempt to adopt or change the existing procedures to meet Canadian needs. This paper outlines the existing test requirements and attempts to predict how they will appear after ""Canadianization"" by the CSA committees.IntroductionFires in underground mines have always been considered more serious than in other locations because of the confined space and limited atmosphere. A fire can make escape difficult or impossible if it is blocking all of the routes to the surface. Also, the products of combustion from an underground fire can asphyxiate anyone not having self-contained breathing apparatus.In an underground coal mine, the consequences of a fire can be even more serious because of the presence of methane and coal dust in the atmosphere (which can explode) and because the coal itself is combustible.For these reasons, the inspection authorities having jurisdiction over underground mine s in Canada are quite concerned about the flammability of any materials that are used in quantity in the underground environmentAs early as 1957, the Canadian Explosive Atmospheres Laboratory (CEAL) was asked to certify conveyor belting as fire-resistant. This is because many miles of this material are used in underground mines in Canada and, as it generally travels through the mine, it is a perfect vehicle for spreading a fire."

Jan 1, 1982

By H. M. Woodrooffe

This paper deals with the laboratory facilities at the Mines Branch for carrying out research in the industrial minerals field, and also reviews current programs in ceramics and construction materials, in non-metallic minerals and in the milling of industrial minerals. It then discusses the application of these pro-grams to industrial problems.

Jan 1, 1967

By The Mill Staff

"IntroductionCOMMENCEMENT of operations at the new No. 7 shaft and 10,000-ton mill at Creighton mine was a major step in the programme of conversion to all-underground mining by the International Nickel Company of Canada, Limited. Planned ten years ago, the orderly transition has been greatly speeded-up to offset the heavy drain on production imposed by World War II and also to meet the increased demand for nickel caused by the current international situation. Development of new mining methods, and process changes in the reduction plants, have made possible the economic recovery and utilization of ore of lower grade than formerly used and of varying metallurgical characteristics. By 1953, when the Company's open-pit mining operations are scheduled for completion, the hoisting capacity of its five underground mines in the Sudbury district will have been increased to 13,000,000 tons per year, compared with 5,700,000 tons of underground ore hoisted in 1950.Two types of ore occur at Creighton. One is a breccia and stringer type that contains a high percent-age of massive sulphides and is located in sheets along shears and in large and small pockets on the underside of the main norite mass; the other type, forming the main part of the ore zone, is mineralized norite that occurs as a •sheet up to 400 feet thick overlying tl1e breccia ore. In both types of ore the minerals of economic interest are pentlandite, which is intimately associated with pyrrhotite, and chalcopyrite. Early mining was confined to the breccia ore; this ore was mined by open stoping methods. The hanging-wall was later allowed to cave, with the result that the old stopes are now filled with caved low-grade ore."

Jan 1, 1952

By J. H. McKibbon

This paper outlines the basic steps in the sizing of electrostatic precipitators according to the Deutsch equation. Design parameters that do not appear in the equation are also described.

Jan 1, 1971