Search Documents

By P. C. Lighthall, D. W. Zandee, W. Shukin

"IntroductionThis chapter deals with the on land disposal and storage of fine tailing in slurry form behind dams. Other types of tailing, such as coarse dry cobbs from magnetic separation of iron ores and other dry materials, have special problems and are not addressed in this paper. The disposal of mine waste is not included, except as such materials may be of value in the construction activities related to tailing disposal.In earlier North American mining, mines were smaller and frequently disposed of their tailing by direct discharge into neighbouring streams or bodies of water. Where that was not practical or not permitted, the solids were collected in tailing ponds and only the effluent liquids were released or decanted. The dams used for these early impoundments were fragile structures and failures were common. With the advent of large, low-grade open pit mines, and increasing awareness of environmental and safety considerations, recently established mines have carefully-designed tailing disposal systems, with wellconstructed dams and attention given to protection of the environment. Older mines are being improved or at least being examined critically with a view to upgrading as necessary to meet the new standards.Modern tailing disposal systems are highly variable and unique to each mine. Tailing pond selection and design is dependent on available topography as also is the design of transport and water reclaim systems. Suitable sites that are at higher elevations than the mills or distant from them may require that the tailings be pumped. Dams, either earth or rock structures built of the most convenient and economic material, are usually a suitable mix of local borrow, mine waste and coarse tailings. The most economic structures are those built mostly of coarse tailing."

Jan 1, 1989

By G. Goodall, D. Mercier, M. Brochu, C. Kaplin

A nanostructured CoNiCrAlY coating was obtained by thermally spraying cryomilled feedstock powder using the high-velocity oxy-fuel (HVOF) process. The oxidation behavior of the nanostructured powder and coating were compared to their conventional counterparts by performing static oxidation tests at 1000°C for durations ranging from 1 to 96 hours. It has been found that oxidation of the conventional powder yielded a duplex oxide scale composed of an inner layer of Al2O3 and an outer layer composed of Cr2O3, NiAl2O4 and other spinels. Interestingly, oxidation of the as-sprayed nanostructured coating yielded a similar duplex oxide scale while oxidation of the polished coating resulted in a single Al2O3 layer. These findings indicated that surface oxide seeds act as nucleation sites for the growth of the mixed oxide layer. Also, it was determined that nanostructuring of the coating promotes the nucleation and growth of a single and adherent a-Al2O3 layer by increasing both the number of diffusion channels and the aluminum concentration at grain boundaries.

Jan 1, 2010

By Claude Hubert, Alex C. Brown, Michel Richard, Rejean Sirois

"The Pierre Beauchemin gold deposit, situated 15 km NW of Rouyn-Noranda, produces an average of 1050 tonnes of ore a day. Reserves are 1.2 Mt grading 5.6 g/t Au. The deposit, located in a shear zone within the Flavrianpluton, in the Blake River Group, is hosted by four major rock types: meta-trondhjemite, meta-tonalite, hybrid rocks and meta-diorite (the prefu; ""meta-"" is omitted thereafter). The trondhjemite, tonalite, and metamorphic hybrid rocks are spatially distributed as a series of sub-horizontal tabular sills that form a genetically related group. Early fractures that permitted either the emplacement of pre-diorite felsic dikes or the formation of a visible alteration caused by early fluid circulation might have been developed in response to initial strain created during regional deformation. These fractures were precursors to the emplacement of diorite and the development of major shear planes. Sub-horizontal north-trending en échelon diorite lenses are observed at the mine. Together, these diorite lenses constitute larger scale diorite zones which are observed at the scale of the pluton. The diorite zones are interpreted as evidence of an episode of sub-vertical extension sustained by the layered trondhjemite, tonalite and hybrid system. The anisotropy created by the less competent sub-horizontal en échelon diorite was an important factor. In shear zone development and subsequent mineralization. The tonalite and diorite accommodated further defomation and developed the main N030°/40° ESE shears along with the spatially associated N060°/50°-60° SSE, and the N000°/10°-40° E shear zones. The N000° shears are interpreted as refracted or deflected equivalents of the N030° shears. The combined shears compose the Eldrich shear system which trends approximately N030°/40° ESE and has had a general reverse movement with a minor sinistral component.Gold mineralization occurs in all four major rock types as en échelon sigmoidal shaped lenses associated with the major N030° deformation system. The distribution of ore lenses can be divided into two categories: The first category occupies sub-horizontal diorite zones. The lenses trend N-S, dip 100 40° E, and are associated with shear zones, sub-horizontal fractures or tonalite-diorite contact planes. The second category of lenses is found in felsic granitic rocks; the lenses trend either N0300!40°ESE or N060°/50°-60° SSE. Local hydraulic breccia zones are observed near ore zones occupying felsic granitic rocks. These breccias may have resulted from high fluid pressures brought upon by confinement as a result of impermeable zones in an anisotropic tonalite-diorite system."

Jan 1, 1990

Waste rock extracted from a mine is typically stored nearby on the surface. Such waste rock piles must be designed to ensure their geotechnical and geochemical stability during the mine operation and after closure. The optimal construction of a pile requires detailed planning. Deposition should involve benches of limited height to control the global slope angle, based on the long term factor of safety. It can also be advantageous to compact the top of each bench and to give the surface an outward inclination to control water flow by limiting infiltration and favoring lateral diversion. When part of the waste rock contains reactive minerals, it is also deemed necessary to use selective placement with the non-reactive portion to prevent direct exposure to natural conditions. The construction must be well documented, and include data from the monitoring program. These and related aspects are presented and discussed in the paper.

Aug 1, 2013

By K. Krishnapisharody, S. Clark, M. Barati

Different gas purging methods to metallurgical baths have been applied to date, among which are top lancing and bottom blowing through tuyeres or porous plugs. Among these, the porous plug bottom blowing technique has shown higher efficiency in gas utilization than tuyeres and top blowing, due to smaller bubble size and lower liquid velocity. However, the studies related to bottom stirring of metallurgical baths are limited to slag-less or thin slag-covered melts. In particular, there is no examination of stirring ability in conditions similar to Falconbridge's Slag Make Converter, where the bath is covered with a thick slag layer and a stream of solids is charged on the bath from top. This study was undertaken to investigate the application of gas purging through a porous plug in stirring in and melting of the solid feeds. The spreading behaviour and melting time of a solid layer forming on a plume created by stirring were calculated using the existing models. The results show that formation of a thick solid layer, specifically in areas beyond the plume region is very likely. Nevertheless, the thickness of the layer and melting time do not appear unreasonably high. It is predicted that by proper controlling of gas flowrate and plug configurations, successful solid charging through the mouth can be practiced.

Jan 1, 2007

By C. Morlot, C. Auvray, E. Fourreau, J. Talandier

"During the excavation of underground galleries in a rock mass, reorganisation of the stress field around the site results in damage to the surrounding material. In the framework of research undertaken at the ANDRA underground laboratory in France, galleries have been excavated in a Callovo-Oxfordian argillite formation. The damage has manifest as a number of fracture systems in the adjacent rock. Observations have shown that fractures generated during excavation and storage exploitation are able to self-seal during re-saturation of the site in the post-closure stage. Although indirect evidence for argillite self-sealing has previously been reported, from experiments performed both in situ and on samples, no direct observations of self-sealing have yet been made.For the present study, we performed a range of self-sealing experiments using a newly-developed triaxial compression cell placed within a nano-CT scanner with a 10 µm resolution. The body of the compression cell is X-ray transparent, allowing sample healing to be monitored directly. The samples contained an artificial fracture that had been generated in the laboratory, into which a fluid was injected. The fractures were orientated either perpendicular or parallel to the plane of anisotropy of the material. Our initial results demonstrate that when fluid is injected perpendicular to the plane of anisotropy, the flow-rate has no apparent influence on the kinetics of fracture closure. Permeability varies significantly, from 2.10-14 to 2.10-18 m2 over 116 hours. Post-test observations of the fracture lips show swelling that appears to be orientated perpendicular to the fracture plane and therefore parallel to the plane of anisotropy. Initial results for an injection parallel to the plane of anisotropy suggest that, in this case, the rate of flow affects the kinetics of fracture closure. For a flow-rate of 0.25 ml/min, closure begins after around one minute. In contrast, for a rate of 0.05 ml/min, it is necessary to wait several minutes before partial sealing of the zone is observed. The reduction in permeability is again significant, from 2.10-15 to 4.10-18 m2 over 96 hours. After completion of the test, swelling was observed in elongated zones that lie parallel to the fracture plane and therefore to the plane of anisotropy."

Jan 1, 2015

By B. Grinbaum, A. Mazuelos, F. Carranza, N. Iglesias, M. Avila, J. L. Lozano, G. Perez, R. Romero, M. \/aliente

Following a failure of a tailings pond darn at a mine in Andalusia, Spain, a huge effluent stream, that contained about 1 g/1 Zn and significant amounts of ferrous, ferric, calcium, copper, aluminium and manganese cations has to be treated, to prevent pollution of a nature reserve. EGMASA, as the regional government environmental agency, suggested to improve the current depuration process by recovery of the Zn from the effluent. A solvent extraction (SX) followed by electrowinning (EW) was proposed and developed to remove zinc.. A pre-treatment stage consisting in bio-oxidation of ferrous iron by using a bacterial process followed by an alkaline precipitation was employed because iron in the effluent is incompatible with both the SX and the EW processes. The SX process was developed successfully at the laboratory scale and verified in a pilot plant on-site, using two Bateman Pulsed Columns for extraction and stripping of zinc. The results were satisfactory obtaining a recovery of 90% of Zn. The process was suitable for industrial application.

Jan 1, 2008

By R. Argane

In this work we assessed the geochemical behavior of concentrator tailings deposited at the abandoned mines of Zeida and Mibladen (Upper Moulouya, Morocco), using physico-chemical analyses, mineralogical characterization, acid base accounting and weathering cell tests. The aim of the study was to evaluate mine drainage quality and to assess metal mobility from these concentrator tailings. Chemical analyses show that the Upper-Moulouya abandoned tailings contain relatively high quantities of lead (0.261 to 0.594 % wt). Mineralogical analyses reveal the abundance of neutralizing minerals (calcite, dolomite, ankerite, and aluminosilicates) which influence mine drainage and metal mobility in mine tailings. Leachate analyses from weathering cell tests show alkaline conditions, small conductivity values, and low solubility of Pb-mineral phases. According to these results, abandoned mine tailings in the Upper-Moulouya district have very low potential for generation of contaminated mine drainage and for leaching of heavy metals. However, the inhalation of tailings exposed to winds generate dust problem facing the local population and may cause health consequences.

Aug 1, 2013

A mini- or micro-machine is a small electro- mechanical device. There are several existing applications of micro-sensors such as the accelerometers used in automobile airbags or the force sensors and grippers used at the ends of micro-surgery tools. Potential applications of existing mini- and micro-technologies are possible and could be used to improve the control and efficiency of fragmentation, heap leaching and other mining and mineral processing operations. A more radical proposition is to devise mass-produced, possibly disposable, minimachines that would operate in large groups. These would be the basis of highly selective, efficient, flexible, and clean mining and mineral processing methods. The paper is intended to promote discussion of how innovative applications of mini-technologies can be used to improve and radically change current mining and mineral processing methods.

Jan 1, 2002

By F. J. Alcock

The Appalachian region of Canada comprises the three maritime provinces; Nova Scotia; New Brunswick; and Prince Edward Island; and that; part of the Province of Quebec lying south and east of Logan's fault. This; major thrust runs in a gently curving line from lake Champlain to Quebec; city and thence down the valley of the St. Lawrence to pass between Anticosti; island and Gaspe peninsula. To the northwest lies the St. Lawrence; Lowland division of the Interior Plains geological province; a region underlain; largely by early Palxozoic strata; which for the most part lie horizontal; or with low dips; where faults occur they are predominantly of the normal; type; and only locally are the beds cut by intrusive rocks. To the southeast; on the other side of the fault zone; an entirely different set of conditions is; encountered. There; Lower Devonian and older strata stand at high angles; are sheared and thrust faulted; and are intruded in many places by granitic; igneous bodies. The present paper is designed to outline briefly the geological; and structural history of this geological province and to emphasize; the part that structural conditions have played in connection with mineral; deposition.

Jan 1, 1954

THE Michipicoten area, one of numerous iron-bearing "Archean" segments in the Shield, contains two main types of iron formation, a normal Keewatin-type, consisting of interbanded chert, siliceous magnetite and jasper, and, gradational to this, a carbonate-sulphide type which contains large de-posits of siderite and pyrite. The carbonate-sulphide type of iron formation bears a direct and intimate relationship to the volcanic development of the area; it there-by affords some insight into genetic problems of Archeanron formation in general. The purpose of this pa-per is to summarize the geological setting of Michipicoten iron formations and to briefly review genetic aspects of recent work in the area. GENERAL GEOLOGY in largely by assorted volcanics and sediments of the Michipicoten series and younger, regional granite masses. (Fig. 1). The Michipicoten series comprises a thick assemblage of mixed flows and pyroclastics together with elastic sediments and banded iron formations. The volcanics belong to the Andesite-Rhyolite Association, and characters-

Jan 1, 1961

By J. A. Beesley

This paper reviews contemporary international law concerning the seabed, current developments in the United Nations on the seabed, and the main outstanding problems. It emphasizes the importance that the Canadian government attaches to this area.

Jan 1, 1969

By J. E. Gill

"THE YEAR 1959 appeared to be a good one in which to attempt a summary of progress in the location and study of sulphide deposits in Canada because a temporary surplus of metals caused prices to fall and many geologists who had been working like beavers were suddenly not so hard pressed. So it was •decided to arrange a Symposium. The response to the call for contributions was excellent and the result is the interesting collection of papers that follow.Activity in the search for massive sulphide deposits has never been as intense as in Canada since 1954. That was the year when the airborne electro-magnetometer first became generally available on a contract basis. These instruments work best on massive sulphide bodies, as do most of the ground electrical survey devices, so much of the new information relates to these. It was decided, therefore, to focus attention in the preparation of symposium papers on such masses. This served also to keep the survey within reasonable limits."

Jan 1, 1960

By H. Thomasson

THE war, like all destructive agencies, has focused attention on salvage and conservation, and to such an extent that a decade of normal progress has been crowded into a few months. This is particularly true as regards the repair of cutting tools. As a consequence, there has arisen a wide demand for comparable data by those engaged in such work, and for basic information by others who wish to repair tools. These repairs may be grouped in three classes: (1) The repair of broken tools of relatively slender cross-section, such as broaches, reamers, drills, etc., of a type that could be returned to service if a means to join the broken surfaces were available, as fortunately it is in the low-temperature silver solder process; (2) the repair of tools that possess shanks, tangs, and other non-cutting portions that may be broken or damaged to the extent that only the addition of metal will permit their return to service; and (3) the repair of special rotating tools, such as end-mills and milling cutters, that may have portions broken from the cutting edges or have their edges so worn in service as to require building up.

Jan 1, 1943

By K. El-Ouassiti, M. Zouadi, C. Bazin, D. Hodouin

Data reconciliation techniques are used to attenuate the effect of measurement errors and estimate unmeasured variables. This paper illustrates the application of data reconciliation to hydrometallurgy processes using measurements from leaching and solvent extraction obtained from laboratory experiments. The application of data reconciliation provides an efficient way to detect gross and systematic errors and produces reliable performance indices for process evaluation.

Jan 1, 2005

By A. -M. Lafront

The corrosion resistance of die-cast and freely-solidified and electromagnetically-stirred thixocast AZ91D alloy has been studied using electrochemical noise technique in a 0.05M NaCI solution at pH 6.1 and 25°C. Specimens polished at different depths were immersed for a period of 75 min in order to assess the influence of the microstructure on corrosion kinetics and morphology. At depths between 10 and 50 µm (skin), all specimens showed general non-uniform corrosion with the lowest corrosion resistance. Between 100 and 200 µmn (interior skin), the observed corrosion was accompanied by superficial undefined pits due to metastable pitting. The corrosion form for 100-200 µm gave the best corrosion resistance. Stable pitting corrosion was observed beyond 400 µm deep on the bulk specimens. The skin of all thixocast specimens prepared billets showed a more corroded surface than that of die-cast. The interior skin as well as the bulk specimens showed better performance than that of the die-cast specimens.

Jan 1, 2007

By Tomoya Kawasaki, Tatsuya Motomura, Yutaka Yasuda

Saganoseki Smelter, one of the largest copper producers in Japan, currently operates a single flash smelting furnace to produce 450,000 tons of new copper annually. The smelter used to employ two flash furnaces, and integrated the two into one in 1996. Since then, various improvements to its facilities and technologies have been made to increase productivity. To upgrade the operation efficiency, "stability" was considered a key issue, and the measures were taken to increase the operation and facility reliability. Currently, the furnace is running at a feed rate of 215 DMT/h, while the furnace utilization has been maintained at 97%. This paper outlines recent improvements that have made to increase furnace productivity and efficiency.

Jan 1, 2014

By S. Steinlechner, S. Wegscheider

"In the past, the metallurgical industry was most of the time dedicated on their main commodity, recovering base metals like zinc, copper or lead but leaving other valuable side elements in the generated residues. As a result, these accompanying minor elements, like gold, silver, indium or also PGMs can be found in the dumps of the corresponding industry. Because of political unrest, strikes, economic reasons or decreasing primary resources leading to a high supply risk, also those mentioned minor elements moved into the focus of the recycling industry. Therefore, beside the base metals, first of all the recovery of those minor metals would be of high interest contributing to the economic viability of recycling processes, although they occur in much smaller quantities in materials. In this context, residues from zinc industry, like leaching residues or precipitation residues show high potential to carry silver as well as indium next to lead and zinc. Therefore, the paper summarizes carried out thermochemical calculations investigating a possible recovery of silver as well as indium by volatilization and the influence of zinc and lead on this process. Based on these theoretical investigations with HSC, trials in lab scale were done verifying the obtained results.INTRODUCTIONHuge amounts of iron precipitate, mainly jarosite get landfilled every year although there is a high content of valuable metals in this residue beside iron. Nevertheless, jarosite has to be dumped due to the presence of contaminating heavy metals. The accumulation of these residues takes up massive land on the one hand but also causes a series of environmental problems in ecosystems on the other. Moreover, some toxic ingredients such as arsenic and cadmium can be dissolved in rain water and are therefore harmful to the health of the aquatic systems. (Erdem & Özverdi, 2011; ÖzverdI & Erdem, 2010) Approximately 0.5 t of dry jarosite accumulate in the production of 1 t of zinc by the hydrometallurgical zinc-winning route (Svens, 2010). Jarosite is a precipitation residue formed during the iron removal. In general, the iron already exists in the zinc ore which is why zinc ferrite builds up during the roasting step of the zinc ore. Zinc ferrite is only soluble in strongly acidic solutions and during the hot acid leaching step it gets dissolved while zinc and iron enter the solution. It is necessary to get rid of the iron because otherwise it would deposit on the cathode first due to its precious character which would be harmful in the zinc-winning electrolysis. Nevertheless successful investigations were done by adding chlorine to the jarosite to recover silver. These findings leads to another residue which occurs in huge amounts – electric arc furnace dust (abbreviated with EAFD) from the iron and steel industry. In 2013 the annual electric steel production reached about 451 million tons. Around 15-20 kg of EAFD is produced per ton of steel in an electric arc furnace (EAF), creating approximately up to 9 million tons of dust per year. (Grabda, Oleszek, Shibata, & Nakamura, 2014; World Steel Association) Next to elements like zinc, lead and iron, chlorine and fluorine are present in this dust. While galvanized steel plates in the scrap act as a source for zinc, casting powders, flame retardants and synthetic coatings are responsible for the chlorine and fluorine contents in the dust."

Jan 1, 2016

By H. C. Gunning

Introduction Considerable attention has of late been attracted to the area surrounding Nimpkish lake, on northern Vancouver island, by the discovery of important rich copper deposits. In less than two years some 200 mineral claims have been staked in a small area, and at least two groups have very promising surface showings. During the summer of 1929, the writer spent one month investigating the general geology and mineral deposits of the region, and, although no detailed work has as yet been done in the field or in the laboratory, the importance of the mineral discoveries and the lack of geological information available to the public warrants a preliminary paper on the district. The district is, from a mining viewpoint, very accessible. Boats from Vancouver call at Englewood, in Beaver cove, four times a week. From Englewood, a first-class logging railway, operated by the Wood, .English Company, extends to the northeast corner of Nimpkish lake. The fifteen-mile trip from the north to the south end of the lake is made by boat, two tugs being maintained by the logging company. The whole trip from Englewood can easily be made in one day. The known mineral deposits lie immediately east of the southern part of the lake, four miles or less from the shore. A fair trail, four miles ? long, leads from the lake to the Nimpkish Copper group. Apart from this trail and an old logging railway grade which follows the east side of Klaanch river for several miles, no trails exist on the southeast side of the lake.

Jan 1, 1930

By Wallace R. Horn

"MR. CHAIRMAN AND GENTLEMEN :I begin this talk by making a couple of comments which are of the nature of disclaimers.Firstly, and as the Chairman has otherwise indicated, I was neither ""born into"" nor have I spent more than a few years of my professional life in the mining industry. I mention this because many might, and perhaps rightly, consider that an added qualification in presenting a report of what the industry has accomplished. Indeed, I am not here to blindly defend all of its actions and inactions in respect to environmental control over the years. Nor am I here to seek absolution of the industry's past transgressions - if indeed that is the word. Mistakes might be a better one. I concluded some time ago that the effects of those mistakes are too difficult to assess against the sea of errors of our total society. I should mention too that I am not an environmental engineer or specialist - only a portion of my interest is involved with this field. Perhaps this permits a perspective which allows a more accurate and objective view.One further comment here. My job today, as I understand it, is to generally report upon the nature and extent of the response of the metals mining industry to control of the environment. In the case of an industry operating at more than a hundred locations and for various reasons at various stages of progress, it is not an easy job. On the other hand, I wanted to avoid the use of generalities because, especially within the context of environmental or ecological opinion and of the practice of condemnation of industrial segments, I think we've had about enough of generalities until we know far more than we do.Finally, I am quite aware that a statement of future plans to achieve environmental control does not impress or satisfy as many people as it may have done some years ago. Public opinion demands to know what is currently underway, today."

Jan 1, 1972