Search Documents

By S. A. R. Keneti

Predicting the geomechanical response of the shale gas material during hydraulic fracturing operation in the field needs better understanding of their geomechanical behaviour under laboratory testing. Anisotropy is considered as a critical factor during investigation and analysis of deviated boreholes, borehole stability, stress-strain and strength behaviour, generation and propagation of fracture and fluid flow. In this study, compressive elastic modulus (Ec) of the Montney shale has been investigated in two perpendicular directions: unconfined compressive strengths test was conducted on the Montney sample to measure its Ec in the vertical direction. This value then was compared to the Ec value in the horizontal plane (i.e. foliation plane) which was previously measured throughout a Brazilian test by Keneti and Wong (2011). From the results, the representative values of Ec in the vertical and in the horizontal directions were found as 25 GPa and 40 GPa, respectively. Computer tomography technique was also employed for the experimental data interpretation.

Jun 1, 2012

By Erik Q. Dahl

The strength of green and sintered pellets during reduction under various conditions in a laboratory kiln has been investigated. Equipment and test methods are described, together with the results obtained. The strength of sintered pellets drops sharply when the reduction starts, and goes through a minimum at the 70 per cent oxidation level. At more advanced reduction, the strength increases with increasing metallization. Successful use of green pellets as kiln feed requires that more attention be paid to the pellet preparation than is necessary when producing pellets for separate sintering. In particular, the ores have to be ground to a greater fineness. The initial strength of green pellets is low. Below the 70 per cent oxidation level, however, the strength of these pellets is about the same as the strength of sintered ones. Additions of such materials as silica, limestone and anthracite coal; within reasonable limits, affect the strength only slightly.

Jan 1, 1966

By A. Haldar

The major problem encountered in the casting of hypereutectic Al-Si alloys is the stoppage of flow below the rigidity level of solid fraction. In this study, the flow stoppage mechanism was studied using three Al-Si alloys with 14%, 18% and 22% silicon. The horizontal foam patterns used were 12.50 mm (0.50 inch) wide with two section thicknesses 12.50 mm (0.50 inch) and 6.25 mm (0.25 inch) with a common sprue. The primary silicon distribution along the length of the casting was studied to determine the mechanism of flow stoppage. It was found that the surface of the flow tip of Al-14%Si alloy was smooth with a few undulations. As the silicon level increased, undulations at the flow tip increased. The number and size of undulations were maximum for the Al-22%Si alloy. Microstructural analysis using optical image analyzer revealed that the flow tip consisted mainly of eutectic silicon in the aluminum matrix and a few primary silicon crystals (PSC). The PSC were in the interlocked condition few centimeters behind the flow tip. It was also found that the gap between the flow tip and the PSC concentrated area increased with an increase in silicon level. Phase characterization was done with SEM-EDX to identify the precipitating phases.

Jan 1, 2007

By D W. MacFadgen

THE operating advantages of the longwall retreating system of mining, as opposed to longwall advancing, have been well known for many years. Although retreat walls have been successfully worked in the past in some of the collieries of the Dominion Steel and Coal Corporation in the Sydney, Picton and Cumberland areas, the adoption of longwaIl retreating as the general sys-tem of mining has not been attractive in the Sydney field, due to the time and expenditures required to drive roadways to the boundary. In addition. difficulties in maintaining effective ventilation on the faces, especially under conditions of low barometer, have made the operators in the field hesitant to adopt this as the general system of mining. The development of a machine capable of rapid entry drivage has made possible the driving of the necessary road ways to the boundary at a moderate cost, completely changing the picture and making a retreat system more attractive.

Jan 1, 1961

By P. Abachi

Cemented carbides or hard metals that generally consist of hard tungsten carbide and a tough metal binder such as cobalt are important in many segments of the world economy, ranging from automobile related components to machining, cutting, and drilling tools. For metal cutting operations such as turning and milling, replaceable cemented carbide inserts are frequently used. The exposure of inserts to very severe conditions (e.g. temperatures as high as 1000°C) in combination with very high loads, limits their lifetime. When the tools and components are scrapped, they are collected with a view to recovering the tungsten carbide and cobalt due to both their environmental aspects and their strategic importance. In this work, a selective electrolysis process was used for recovery of WC powder particles from cemented carbide scraps. The WC-10Co and WC-10Co-VC up to 3 wt.% VC was produced using powder metallurgy route. The mean particle size of WC, Co and VC were selected as 2.5, l.5 and 2.2 µm respectively. Referring to electrochemical curves of WC-10Co cemented carbides in hydrochloric acid solutions with different concentrations, the recovery rate was enhanced in IN acid. Therefore, this solution was selected for recycling of all samples. The surfaces of as-produced and corroded specimens were investigated using a scanning electron microscopy (SEM). Detection of corrosion products was provided by energy dispersive spectrometry (EDS). According to results, the selective electrolysis process could be useful in the recycling of scrap carbide materials, although more studies should be undertaken on economical aspects of the process and the quality of samples produced using recovered powders.

Jan 1, 2005

By Horatio Sam-Aggrey, Margot Hurlbert

Small Modular Reactors (SMRs) have been touted as having the potential to spearhead a nuclear renaissance. Proponents of this view cite the relative advantages of SMRs over larger nuclear plants as reason for their optimism. Some of these merits include potential economies of mass production deriving from modular factory production, enhanced safety features, the ability to locate reactors in remote areas, and reduced requirements for technical workforces to install and maintain SMRs. Despite the optimism surrounding SMRs, nuclear power is still a contentious issue for many Canadians. The growth of nuclear power remains adversely affected by concerns over issues such as: the health and safety consequences of nuclear power generation, environmental impacts, proliferation of nuclear materials, terrorism, and radioactive waste disposal (Organisation for Economic Co-operation and Development (OECD) and Nuclear Energy Agency (NEA), 2010). Personal values, past nuclear accidents, and lack of trust in the industry are other factors influencing attitudes toward nuclear energy (IAEA, 2005). In Canada, three main areas where SMRs could be used have been identified. These include: a. Traditional, on-grid power generation, especially in provinces looking for zero-emissions replacements for CO2-emitting coal plants. B. Remote off grid communities that currently rely on diesel or fuel oil power generation. There are 279 off-grid communities in Canada, many of them being Aboriginal communities (NRCan, ND). Notably, all communities in each of Canada’s three territories qualify as remote. C. Resource extraction sites, such as mining and oil and gas extraction sites. Many of Canada’s principal producing mines and active mineral exploration projects are located within close proximity of Aboriginal communities. Any proposed implementation of small nuclear plants would, require the support of the local population, which is largely Indigenous in the northern regions. The possible deployment of SMRs raises important issue relating to consultation and accommodation of Aboriginal concerns regarding potential SMR deployment. This is especially pertinent given Canada’s pending implementation of the provisions of UNDRIP. One of the provisions of UNDRIP that has attracted a lot of attention is the one on Free Prior and Informed Consent (FPIC). Drawing on previously published information, this paper discusses some of the challenges posed by FPIC for the deployment of SMRs. The next section outlines the provisions of FPIC and its implementation in the Canadian context. Section 3, details some of the challenges posed by FPIC to the deployment of SMRs, while Section 4 provides some concluding comments.

Jan 1, 2020

By E. Lovera

ABSTRACT: The current study analyzes the feasibility of an odd operation: to obtain, using a properly tailored drilling and blasting scheme, blocks suitable for the production of dimension stone from tunnel driving. Clearly, a compromise must be found between the rate of progression and the achievement of workable blocks. As a case study, a civil work under consideration in northern Italy was examined. The work was planned to cross a conglomerate that has traditionally been locally exploited for the production of highly prized paving and lining stones with excellent strength and aesthetic features. Natural exposures and mined-out quarries were available for tests. The relevant rock data are given, blast designs are shown (within the limitations of contour accuracy), and the test program is described.

Jan 1, 2011

By B. R. Rakishev

When transferring from the railway transport to the combined automobile-conveyor transport by stripping works at coal mines, it was proposed to form at the working zone a concentration horizon for reloading part of the stripping volumes at the railway transport. The procedure is adduced for substantiating parameters of bloc-panels, depending on the step of transferring of reloading points in interrelation with the intensity of the working zone?s development with observing the balanced movement of parts of the stripping zone relative to the temporary concentration level.

Aug 1, 2013

By Jason Mewis

Jason Mewis is the founder and president of ENGCOMP, a consulting engineering firm in Saskatoon Saskatchewan focusing on the mining sector. He has over 17 years of experience working on projects for the heavy industrial market in Saskatchewan, as both a Senior Structural Engineer and Project Manager. Jason is an entrepreneur with experience in many areas including estimating, planning, facilitation, and Risk Analysis. He has presented at many seminars and conferences across North America on the subject of Project Risk and and has become recognized for his expertise in this area of project management.

May 1, 2013

By David Stone

North American Palladium is the owner/operator of the Lac des Iles mine located 115 km north of Thunder Bay, Ontario. The mine has produced an average of 65,000 ounces of palladium since 1994. Lac des Iles is currently undergoing the first phase of a major expansion that will increase ore production from 2,400 tons per day to 15,000 tons per day. A future expansion is being contemplated for 30,000 tons per day. The current expansion will increase palladium output to 250,000 ounces per year. The mine plan for the ultimate pit results in an excavation 1 km long by 800 m wide and over 450 m deep. This makes the ultimate pit at Lac des Iles one of the ten deepest open pits in the world, and the largest in Canada. This paper outlines the geotechnical data collection and design methodology for the ultimate open pit at Lac des Iles.

May 1, 2001

By S. Xu

Magnesium alloy AM50 is of interest to automotive cradle application because of it excellent castability and good ductility. In this work, microstructure and mechanical properties of both low pressure die cast (LPDC) and high pressure die cast (HPDC) AM50 test bars are characterized. Microstructure was examined using optical microscope, scanning electron microscope (SEM) and transmission electron microscope (TEM). Phase identifications were performed using energy dispersive x-ray spectrometer (EDS) and TEM diffraction. It has been found that LPDC produces much coarser microstructure than HPDC. At the same time, the HPDC samples are more heterogeneous in microstructure and composition close to grain boundaries. Particles with various dimensions and morphologies of two different intermetallic phases, Mg17A112 and A18Mn5, were found in all the samples. Mechanical tests were performed under conditions similar to those related to an engine cradle application. LPDC samples show lower strength but better creep resistance than HPDC mainly due to the difference in grain sizes and grain boundary microstructure between LPDC and HPDC. Creep curves are well described by the empirical Andrade equation. Tensile-compressive yield and creep asymmetries were found in AM50, i.e. better deformation resistance in tension than in compression. The average yield asymmetry ratio for all the samples is 0.87. Microstructural examinations on the samples tested in tension, compression and creep showed that the deformation mechanisms in AM50 were slip plus twining at temperatures up to 125°C. The examinations indicate the important role of twining in the asymmetry phenomenon. The creep results indicate that dynamic precipitation of the Mg17A112 phase during testing is not the mechanism directly responsible for the creep asymmetry in AM50.

Jan 1, 2004

By John F. Gartner

"Traditionally, the geologists of Canada have been occupied with the tasks of finding new mineral bodies, locating gas and oil fields or hunting for economic deposits of industrial minerals. A very minor percentage of graduate geologists have applied their skills to solution of the ""urban blight"" or employing their understanding of ""Nature"" for the optimum use of land by mankind. However, things are changing quickly. The role of the geologist in the planning process is being established. It is an exciting time! Geologists are now being consulted on a wide range of urban planning problems. These vary, tor example, from assessment of the geological environment for the new communities of Erin Mills and Meadowvale, which will have total populations in excess of 100,000 people (truly a satellite city), to a complete geological/ geohydrological assessment of the new sanitary landfill for the city of Guelph.Use of geologic techniques and methods for urban studies must be enhanced with certain skills not taught, in the past, to the geologist. These include airphoto interpretation, soil mechanics, geohydrology, municipal engineering and highway engineering to mention a few. The geologist has the unique training to assess the natural environment and to discover, warn and explain the implications of man's attempt to command his environment."

Jan 1, 1972

By Y. W. Pan, Y. R. Liu

The disturbed natural rock mass tends to equilibrium state accompanying with non-equilibrium evolution process which has significant influence on the long-term stability of engineering structure. The deformation development in the non-equilibrium evolution is determined by two intrinsic processes, trend to equilibrium and damage development, which can be illustrated by evolution of excavated tunnel. Thus the creep and damage must be taken into account in study of non-equilibrium evolution process. Within Rice’s irreversible thermodynamics with internal state variable (ISV), the conjugate force function which equals to zero is a convex surface which divide the stress space into two parts, called equilibrium and nonequilibrium stress space respectively. The concept of effective stress of non-equilibrium has been proposed, in which the stress difference (d - d ) are the effective driving forces of non-equilibrium evolution process with hardening and damage effective. The formulations of inelastic strain rate and energy dissipation rate have been recast in the form of effective stresses. The inelastic complementary energy (ICE) is proposed to measure intensity of non-equilibrium evolution of material system. The specific equations of conjugated forces and kinetic equations of internal state variables are presented. The ICE and rate of energy dissipation are all calculated to be used to evaluate long-term stability of geo-engineering. The results show that rate of energy dissipation may be more convenience and flexible than ICE for internal state variable constitutive equation of rock mass.

Jan 1, 2015

By Y. Zedan

In this study, the statistical design of experiments (DOE) was applied to study and regulate the properties of near-eutectic Al-11%Si alloys. Develop regression equations for such response variables as hardness, yield stress, ultimate tensile stress, percent elongation, total cutting force, cutting power, and tool life together with other factors which, include the percentage composition of the alloying elements, and the requisite modification (Sr) level. These equations may be analyzed quantitatively to acquire an understating of the effects which the main variables and their interactions may have on the mechanical behaviour and the machinability of the alloy under investigation. The results reveal that increasing the levels of Cu and Fe content results in an increase in hardness, yield stress, and ultimate tensile strength in both modified and non-modified alloys. On the other hand, both Cu and Fe appear to affect the percentage elongation adversely, whereas the Sr-level has a positive effect on this parameter. It was found that Sr-levels have the most significant effect on the cutting forces and cutting power followed by the content in Fe and Cu. The results also reveal that the interaction coefficients of these variables have a significant effect on tool life compared to the main independent variables. This fact may be attributed to the formation of complex insoluble phases between Cu, Fe, Si, and Al as investigated using Scanning Electron Microscopy (SEM) attached to an EDX analysis system. The accuracy of the regression equations in predicting the expected properties has been verified by carrying out random experiments in the range of variation of these variables.

Jan 1, 2011

By L. Shang

In conventional continuous hot rolling processes, metals are usually reheated to a temperature such that the workpiece will maintain appropriate hot working characteristics as it proceeds through the rolling mill, assuming that the temperature is continually decreasing. Metallurgically, reheating will reduce micro-segregation in the as-cast material, may increase the as-cast grain size and will affect any second phase particles present in the as-cast structure. All these changes can affect the hot working characteristics, and the final as-hot rolled microstructure. In order to study the effect of reheating on AZ31 magnesium alloy, a plate sample was cast in a water cooled copper mould and a series of compression tests was performed at a temperature of 350 °C, strain rate 0.01 5-1, and strains from 0.2 to 1.0, after different reheating schedules. It was found that there is no significant difference in flow behavior between the as-cast sample and all but one of the reheated ones. The reheat treatment of the 'anomalous' sample was a two stage heat treatment; it was first reheated to 450 °C, cooled to room temperature, then reheated to 350 °C. The effect on the flow curve was to increase the flow stress. This result may be related to changes in second phase particle characteristics.

Jan 1, 2006

By N. Birbilis, S. Kairy, C. R. Hutchinson, D. Jiang, D. R. Feenstra, O. Gharbi

"Recent developments in metal-based additive manufacturing (AM) technology have generated considerable interest in multiple industries, owing to flexibility in design and the ability to produce final components in their net shape. The AM of high-strength aluminium alloys has not been widely explored, due to findings of undesirable microstructures leading to short fatigue life and poor fracture toughness; restricting the application of AM to lower strength aluminium alloys (with cast-like Al-alloy compositions) to date. Herein, aluminium alloy AA2024 (Al-3.6Cu-1.2Mg) was additively manufactured via selective laser melting (SLM), with the resultant microstructures and corrosion properties characterised and compared to wrought AA2024-T3. Microstructural characterisation was carried out using transmission electron microscopy (TEM), revealing SLM produced AA2024 included a population of ?-phase (Al2Cu) in preference to S-phase (Al2CuMg) typical of wrought AA2024. Additionally, the corrosion properties were investigated by potentiodynamic polarisation in a range of NaCl concentrations, whilst elemental corrosion rates were also determined (including for open circuit exposure conditions) and quantified in situ with an inductively coupled plasma mass spectrometer coupled with an electrochemical flow cell. Results revealed a significant improvement in the corrosion resistance, and elemental dissolution of AM prepared 2024 relative to wrought AA2024-T3.INTRODUCTION Aluminium alloys remain the preferred candidate materials in applications requiring a balance of low density and strength. The ability to produce net shape components from aluminium alloys has accelerated due to recent developments in metal-based additive manufacturing (AM) technology, including selective laser melting (SLM) and powder bed 3D printing. The AM of Al-alloys, including Al-Si-Mg (namely AlSi10Mg), has become widespread commercially in recent years. Alloys including AlSi10Mg offer reliable and reproducible production by AM, however such alloys (and variants thereof) are not high strength alloys. The pursuit of higher strength AM Al-alloys presents significant merit to multiple industries; however, such higher strength AM Al-alloys have not been widely studied to date. The solidification of high strength Al-alloys during conventional (casting) operations needs to be executed in a manner that avoids so-called =hot-tearing‘, which can arise as a result of the solute type and loading. A report on the solidification of a high strength Al-alloy prepared by AM, along with factors related to solidification, was recently covered by Pollock and co-workers (Martin et al., 2017). It was reported that AM of high-strength aluminium alloys (which have to date been principally based on the compositions of wrought high strength Al-alloys) may lead to undesirable microstructures that reduce fatigue life and result in poor fracture toughness; presently limiting the application of AM to lower strength aluminium alloys (with cast-like Al-alloy compositions) to date."

Jan 1, 2018

By M. Kataoka, Y. Obara

It is known that compressive strength and tensile strength of rocks vary significantly with specimen size. Rocks are composed of crystals and grains in a fabric that includes flaws such as microcracks, grain boundaries and pores. As the likelihood of including severer flaws becomes greater for a larger specimen, the strengths are small. On the other hand, the size effect in the fracture toughness of rocks has not been made clear until now because there are few studies focused on it. In this paper, Semi- Circular Bend (SCB) test was performed using Kimachi sandstone with various specimen sizes. A shape of the specimen is a semi-circular disc with an artificial notch. The specimens were prepared with various thickness t and radius r as the following two groups; t was changed from 10 to 37.5 mm with r = 37.5 mm in the specimen of group (a), and r was changed from 12.5 to 150 mm with t/r = 0.8 in the specimen of group (b). As a result, there was no significant change in the fracture toughness with different t. On the other hand, the fracture toughness increased with increasing r and converged on a certain constant value in a range larger than approximately 70 mm of r. Consequently it was clear that the size effect in the fracture toughness of the sandstone exists.

Jan 1, 2015

By R. W. Bruce, K. W. Downes

"IntroductionSULPHUR production in Canada from all sources for the year 1953 amounted to about 375,000 tons. Except for 16,000 tons of elemental sulphur derived from natural gas, this production was in the form of by-product pyrites, liquid sulphur dioxide, and sulphuric acid. In the same year, Canadian industry imported 359,000 tons of elemental sulphur from the United States. The cost, including transportation charges, to Canadian consuming plants ranged from $35.00 to $45.00 per long ton, depending upon location.Although most of the sulphur consumed is used in the oxidized form it is often most convenient to buy sulphur in the elemental form, and convert it to sulphur dioxide or sulphuric acid in situ as required. This is because elemental sulphur is easily shipped and stored, weighs only half as much as an equivalent quantity of sulphur dioxide and one-third as much as the corresponding quantity of sulphuric acid, and is readily converted to these forms in a sulphur burner. A process, therefore, which could economically recover elemental sulphur from sulphide ores would be most attractive.Since the turn of the century, notable improvements have been made in extractive metallurgy, but until recently only limited attention has been paid to the possibilities of elemental sulphur recovery. This has been due to the plentiful supplies of cheaply mined Frasch sulphur which have been available on the world markets."

Jan 1, 1955

By James Kear, Romain Prioul, Robert G. Jeffrey, Andrew P. Bunger, Dimitry Chuprakov

"Unconventional gas and geothermal reservoirs are typically naturally fractured and therefore the challenging problem of hydraulic fracture (HF) growth through naturally fractured rocks is an important issue especially for the development of accurate predictive HF models. This paper presents results from laboratory experiments in which HFs have been created in both sandstone and crystalline (gabbronorite) rock specimens such that they impinge either orthogonally or at an oblique angle on an unbonded, machined frictional interface. Depending on the conditions of each experiment, the fractures either cross or are blunted at the interface. The growth behavior was ascertained for these experiments based on a synthesis of the injection pressure record, active ultrasound monitoring, and direct post-experiment inspection of fractured specimens. From these experiments we observe: 1) A contrast between direct crossing and crossing with an offset for orthogonal and oblique intersection, respectively, 2) Apparent independence of crossing/blunting behavior on the friction coefficient for orthogonal intersection, 3) Dependence of the stresses required to promote crossing on the intersection angle between the HF and NF, 4) Existence of cases in which the hydraulic fracture crosses but then essentially ceases propagation such that all fluid is diverted to the interface. INTRODUCTIONHydraulic fracturing is a vital technology used to increase the productivity of oil, gas, and geothermal wells. Predicting hydraulic fracture (HF) growth is, in turn, critical to design of hydraulic fractures that grow to the desired length, accept the desired amount of proppant, and remain contained in the reservoir without unwanted height growth into surrounding layers (e.g. Economides and Nolte, 2000). The importance of HF modeling has prompted 6 decades of research during which simulators have become more efficient, more accurate, and have addressed a growing range of complexities (see review of e.g. Adachi et al., 2007).One of these complexities is the interaction between HFs and mechanical discontinuities such as natural fractures (NFs). Efforts in this area have been mainly driven by development of unconventional (i.e. low permeability) oil and gas resources because essentially all viable low permeability reservoirs, including shale gas/oil reservoirs, are naturally fractured to some degree (King, 2010). One of the most important questions for developing effective HF stimulation strategies in these reservoirs is whether the hydraulic fracture(s) is/are expected to be single-stranded or whether interaction with the NFs will lead to network-like growth. The basic building block for numerical simulators that can address this question (such as Kresse et al., 2013 and Weng et al., 2014) is whether an HF that intersects an NF will cross the NF or whether its growth will be captured by the NF so that additional fluid injection pressurizes the NF but does not generate ongoing growth of a new HF. These scenarios, including subcategories such as crossing with an offset, have been recognized for several decades (Daneshy, 1974; Warpinski and Teufel, 1987, and as recently reviewed and expanded by Chuprakov et al., 2013)."

Jan 1, 2015

By Takanori Kokubo, Kenta Suzuki, Tomohiro Sasaki, Toshiya Anami

"Previous work has shown that the strengthening Al-Mn alloys with copper leads to the formation of an undesirable reduction in recrystallized grain size. In this study the mechanisms of strengthening and recrystallization behavior in a continuously cast automotive heat exchanger fin stockof Al-1.1wt%Mn-0.5wt%Fe-0.3wt%Si with a0.3wt%Cu addition were investigated. Metallurgical analysis revealed that the Cu strengthening was dominated by the formation of dispersoid particles, while solid solution strengthening decreased with the Cu additions. This result is attributed to the decrease in the amount of Mn solid solution. The post brazing recrystallized grain size was reduced compared to that not containing Cu. It is postulated that the Cu addition leads to a decrease in the amount of Mn in solid solution which leads to a finer grain size. This effect is attributed to Mn in the aluminum matrix inhibiting boundary migration but allowing other grains to grow during heat treatment. The results are rationalized based on particle stimulated nucleation (PSN), wherein dispersoid particles are more likely to become active recrystallization nuclei during the heat treatment. The increase in the number of active dispersoid particles with Cu addition is correlated to the recrystallized grain structure.INTRODUCTIONImprovements in properties such as strength, braze ability and corrosion resistance in thermal fin stock alloys are all means to gain improved efficiency in heat exchangers particularly in automotive applications. While Al-Mn alloys dominate automotive heat exchanger fin stock alloy, even small chemical compositional changes can profoundly influence these properties (Kawaharaet al., 2004; Yoshino et al., 2009). The microstructure (particularly the grain size and shape) also plays a key role in determining the product performance and hence the thermo-mechanical processing (TMP) must also be considered. The casting method (typically conventional direct chill, DC, or continuous casting) significantly influences the properties in no small part due to the very different TMP routes that are used. Continuous casting is generally favored for fin stock applications as its higher cooling rate (which can be 2 to 3 orders of magnitude higher than DC casting) leads to finer as-solidified intermetallic particles and an increase in super-saturated solid solution elements (such as Mn)that are known to improve fin stock performance such as strength, braze ability(Okiet al., 2008)."

Jan 1, 2018