Search Documents

By L. Yaun

In underground coal mining operations, gas content in a coal seam is used to assess the risk of coal and gas outbursts. To estimate the gas content, a number of systems have been developed, however issues remain about the rapidness and accuracy of these systems. To address these issues, a new and improved system has been developed that includes a sampling-while-drilling unit for coal sampling, a coal canister, an underground-based portable measurement unit, a surface-based measurement apparatus, and gas content calculation software. The system has been successfully applied in underground coal mines at Huainan, China. This new, rapid and accurate system, its main components and field trials are described in this paper.

Aug 1, 2013

By J. P. Caulfield

THE Hudson Bay Mining and Smelting Company's underground mine at Flin Flon, Manitoba, has in the past been serviced by two working shafts-the North Main shaft, and the No. 3 shaft. The North Main shaft is used to hoist the total production from under-ground, and handles the greater part of the mine supplies and crews. The shaft is five-compartment design, rectangular in cross-section, and is equipped entirely with steel shaft sets from the surface to the finished depth of 2,210 feet. Hoisting equipment in the surface plant will not permit the North Main shaft to be extended below its present finished depth. The No. 3 shaft, located approximately 2,300 feet from the North Main shaft, is used primarily as a ventilation shaft, and for hoisting lower-level development waste to the 390 level, where this material is used as mine fill. The No. 3 shaft is of standard rectangular design, timbered with 8-in. by 8-in. creosoted fir sets, hung on 6-foot centres. From the surface to the 1,430 level, the No. 3 shaft consists of three 5 ft. by 5 ft. compartments, and below this level to the completed depth of 2,300 feet, the shaft is increased to four compartments. To service the mine and to expedite development below the 2,210 level, a one and one-half compartment winze was sunk from the 2,210 level to a depth of 766 feet, or approxima tel y the 3,000 level.

Jan 1, 1941

By P. R. A. Andrews

"Graphite is one of the most versatile of non-metallic minerals because of its diversified properties, for example: it is unctuous; it marks readily; burns slowly; is almost chemically inert; is flexible over a large temperature range; is a good conductor of heat and electricity; is hydrophobic; has a negative temperature coefficient of resistivity; has excellent weathering properties; tends to emulsify with water-in-oil; is readily soluble in iron; and after oxidative treatment, can exfoliate like vermiculite. These properties give rise to its major uses in lubrication, refractories, marking instruments, electrical products and paints.Flake graphite is the variety which commonly occurs in Canada; the provinces of Ontario and Quebec contain the deposits of economic significance, although graphite occurs in other provinces. The beneficiation of graphite has been the subject of many investigations at CANMET, thus reflecting graphite 's importance as an industrial mineral. Thirty-eight studies relating to various aspects of beneficiation were conducted between 1918and 1989anda review of some of the more important studies is presented. The information includes mineralogy, beneficiation methods and results; flotation parameters and reagent concentration data are presented in tabular form. By so arranging the principal data, the research worker and production metallurgist will be assisted in the evaluation of graphite ores from a variety of origins."

Jan 1, 1992

By Jun Deng

The aim of this paper is to study the scientificity and reliability of three coal gas indices used to predict coal fire disasters, namely Graham?s ratio, CO/CO2 ratio, Litton ratio and their different characteristics and service conditions. Data from a programmed temperature experiment were applied to check their veracity and accuracy. Each index performed well in detecting the level of a fire. We conclude that it is better to redefine the definition through experimentation before applying a given index. Integrated analysis of the results can provide reliable reference data for predicting spontaneous combustion of coal.

Aug 1, 2013

By A. G. Lylie

Introduction At the Britannia Mining and Smelting Company's mill, the equivalent of 2,500 to 2,800 pounds of copper sulphate crystals per day is made from copper which is precipitated from the mine-water. This copper sulphate is used in the mill for the recovery of sphalerite by2 flotation. From 1932 until 1936 it was produced by exposing the precipitate to air for thirty days and then dissolving the oxidized copper with dilute sulphuric acid. In 1936, the flotation of sphalerite was discontinued and, when it was resumed in 1947, steps were taken to try to improve the former method. The present paper outlines the way in which this was done, and describes the plant and procedure by which copper sulphate is now being made, and by means of which an appreciable saving is being effected. Aboratory Tests The previous work had established that the precipitate, which consists mainly of metallic copper, must be oxidized before the copper would dissolve in dilute sulphuric acid. Various methods for oxidizing it were tried but in the early laboratory work the only suitable one found was to heat the precipitate to 600°C. and hold it at this temperature for two hours. When this was done, approximately 90 per cent of the copper became soluble in .acid. This percentage was considered satisfactory for practical purposes, but the cost of roasting was prohibitive because only a small amount of roasted precipitate was required each day.

Jan 1, 1951

By J. A. Drozdiak, W. Tse, P. P. Rosario

"In a recent publication (SAG 2015), we presented a non-conventional high pressure grinding roll (HPGR)-ball mill circuit as a lower capital cost alternative to the “standard” HPGR circuit. The circuit was designed for the treatment of a hard ore and relatively high tonnage (50,000 t/d). That paper provided details such as flowsheets, layouts, and equipment lists for the two options and compared their calculated capital costs demonstrating significant savings for the proposed circuit. This paper extends the analysis to a third option, a traditional semi-autogenous ball crushing circuit, giving the same level of details and now including the operating cost estimates for all three options for a more comprehensive analysis. Moreover, this work also provides information about the strengths and weaknesses of the non-conventional HPGR circuit when compared to the “standard” HPGR option.This study demonstrates that the proposed non-conventional HPGR-based circuit not only provides a lower overall capital costs for the project if compared to a “standard” HPGR circuit but also brings the capital cost to the level of the traditional semi-autogenous grinding (SAG)-ball mill circuits. In addition, the innovative HPGR circuit provides similar operational cost savings of the “standard” HPGR and thus a significant advantage when compared to the SAG option. With the current capital cost sensitivity for most greenfield projects, the proposed alternative circuit should help make HPGR-based circuits more competitive and thus promote the utilization of a technology that enables higher energy efficiency and reduced greenhouse gas emissions. INTRODUCTIONThe application of high pressure grinding roll (HPGR) technology in comminution circuits is well established for the processing of cement, diamonds and iron ore (Broeckmann & Gardula, 2005), and over the past 10–15 years, this technology has slowly been applied to hard ores in high-tonnage precious and base metal operations. Unfortunately, under the current economic climate, the ability to finance large capital projects has become very difficult and companies tend to have an easier time securing funding if the capital expenditures (CAPEX) are low with a proven process method. The traditional semi-autogenous grinding (SAG) mill / ball mill circuits easily fit into this mould, having been installed in countless plants around the world over the past 30 years with relatively low capital requirements. In contrast, it has been well-documented that HPGR-based circuits are capital intensive with complex material handling systems (Seidel, Logan, LeVier, & Veillette, 2006). Although these circuits benefit from reduced operating costs with the increase in energy efficiency and the elimination of steel grinding media (Rosario, Boyd, & Grundy, 2009), if the company is unable to secure financing to build the plant, these advantages remain out of reach. With the current trend to retrofit existing SAG circuits with a secondary crushing circuit to achieve design throughput, the opportunity to circumvent this gross inefficiency by making HPGR-based circuits more capital friendly would greatly benefit the industry."

Jan 1, 2016

By Å. Partapuoli, M. Henriksson, P. Wikström, J. Worth, G. Adolfsson

The control of AG mills fed by ores with harder and softer components can be challenging due to the sensitivity of the mill to the ratio of hard to soft components. The mills at LKAB’s iron ore operations are generally well controlled, but there are periods when the throughput falls off dramatically, due to a loss of mill filling. As the ore is upgraded in the sorting plant through magnetic separation prior to milling, this presents an opportunity to manipulate the feed blend in advance. In order to assess this opportunity, a fullscale mill charge was dumped and assayed by size to quantify the build-up of competent waste in the mills. This was supplemented by pilot and locked-cycle laboratory tests at a wide range of feed blends in order to facilitate the development of an appropriate multi-component AG mill model. This paper reports the experimental campaign requirements and methodologies, as well as the major outcomes from analysis and modelling exercises using the industrial, pilot and laboratory multi-component data.

Jan 1, 2012

By Leroy C. Stewart

Owing mainly to the use of ethylene dibromide in the production of tetraethyl lead for gasoline treatment, there has been a tremendous increase during the past decade in the demand for bromine. In the United States, production, derived mainly as a by-product from the treatment of brines from salt wells, rose steadily from about two million pounds in 1924 to nine million pounds in 1931. In 1936, production amounted to between 20 and 21 million pounds. Much of the increase during the past four or five years has been due to the operation of the Ethyl-Dow Chemical Company's plant, which extracts bromine directly from sea water. The process employed by the Ethyl-Dow Company is somewhat similar to that in use on salt-well brines at their plant at Midland, Michigan, but whereas these brines contain around 1,300 parts per million bromine, sea water contains only 65 to 70 p.p.m.-about as much as the waste effluent in the brine process. By intensive research, however, a process was developed whereby a very considerable percentage of the bromine content of sea water could be recovered, and at a satisfactory operating cost. In its essentials, the process consists in liberating the bromine from the sea water by treat-ment with chlorine, blowing the bromine out of the water by a current of air, and finally absorbing it in a solution of soda-ash.

Jan 1, 1938

By Denghong Wang

Abstract- The Ashele Cu-Zn deposit is a recently discovered volcanogenic massive sulfide deposit in Xinjiang, China, hosted by Lower to Middle Devonian submarine bimodal volcanic rocks. The primary ores of this polygenetic deposit are represented by massive syn-depositional pyrite, chalcopyrite, and sphalerite, and were formed by submarine exhalation. Hydrothermal alteration consists of strong sericitization, chloritization, silicification, and carbonatization of the metavolcanic rocks beneath the massive orebodies. Depletion of Na2O is an obvious chemical change in the hydrothermal halo. Geological and geochemical evidence suggest that the Ashele Cu-Zn massive sulfide deposit was formed by submarine exhalation related to bimodal volcanic rocks, trapped in a rifting basin, then deformed by shearing, and thermally metamorphosed by the intrusion of dacitic porphyry. Sulfur and lead isotopic studies indicate that metals such as copper and zinc may have originated from spilites, but that volatile components, especially sulfur, were derived directly from submarine volcanic magmas.

Jan 1, 1999

By Yong-neng Feng, Xiao-ping Chen, Wei Guo

"While the uniaxial compressive strength of rock has been extensively investigated, the relation between the saturation and natural compressive strength is relatively unexplored. This paper studies on 1865 statistical data of Chongqing Rail Transit Line 1 and Line 6, which located in the Middle Jurassic of Shaximiao formation. The research focuses on the relation between the saturation and natural compressive strength. The statistical data are categorized and quantified in order to ascertain the softening properties of sandstone and sandy mudstone. The findings suggest that the saturation compressive strength is significant effected by its natural compressive strength, and an empirical formula is introduced to explain the relation. These findings have implications for researchers and engineer who concerned with Chongqing rail transit construction.INTRODUCTIONIn the engineering construction and surrounding rock classification, the uniaxial compressive strength index (Ministry of Water Conservancy, 1995; Ministry of Railways, 1999) is one of the essential parameters of rock mass. Usually, there are two types of the uniaxial compressive strength index, natural and saturation compressive strength, and the ratio of them is the softening coefficient. Most of the previous studies on rock strength had focused on the influence factors (Liu et al., 2008; Liu et al., 1998; Liu et al., 2013; Wang, 2013; Zhang et al., 2008; Zhang et al., 2010; Zeng & Lin, 2003) with experiment and in-situ tests. But few publications that reports a long and formal research project on the relationship between natural and saturation compressive strength. In order to figure out this issue, this study investigated the distribution of Solidity Classification of Rock Mass and softening coefficient based on the statistical data of Chongqing Rail Transit Line 1 and Line 6. Based on the analysis, an empirical formula was proposed to explain the relationship."

Jan 1, 2015

By G. Archibald, M. McSaveney, J. Wartman, M. Yetton, C. Massey, C. Holden, A. Kaiser

"The 2010/11 Canterbury earthquakes triggered many mass movements in the Port Hills including rockfalls, rock and debris avalanches, slides and slumps and associated cliff-top cracking. The most abundant mass movements with the highest risk to people and buildings were rockfalls and rock/debris avalanches. Over 100 residential homes were impacted by landslides, leading to the evacuation of several hundred residents.Volumes of rock leaving several of the larger cliffs during the earthquake sequence were determined from terrestrial laser scan change models. There were no seismically instrumented cliff sites and there was some distance between the cliffs and nearest strong-motion sites. Therefore, we synthesised free-field rock-outcrop seismograms by employing a stochastic approach controlled by source models and regional parameters derived using spectral inversion of the extensive strong motion data set. Relationships between volumes leaving cliffs during the earthquakes and site peak ground acceleration (PGA), peak ground velocity (PGV) and Arias intensity were compared for different sites. Multiple linear regression was used to analyse the variables that best predict the volumes of debris that fell from the slopes during the main earthquakes. The best correlation between the volume of debris falling per square metre of slope face and the seismic forcing parameters was for vertical PGV. The results from the multiple linear regression incorporating slope height, inclination, PGV horizontal and PGV vertical, improved the statistical relationship.Field data and results from the 2D seismic site response assessment indicate that the following factors affect dynamic performance of the modelled cliffs: 1) cliff geology—mainly material modulus, shear strength and shear wave velocity; 2) slope geometry—ridge-scale versus site-scale effects; and 3) the temporal aspects of the earthquake shaking (i.e., single acceleration peaks of large amplitude versus multiple peaks of smaller amplitude). Model results show that amplification of shaking does not increase linearly with increasing height, but instead reflects changes in the cliff geology where material strength, modulus and shear-wave velocity contrasts lead to acceleration contrasts.These factors show that the use of well documented case histories provide the basis for more certainty in seismic landslide assessments compared to those that are only empirically based."

Jan 1, 2015

By A. Ojaghi, A. R. Mohammadi

"The Marvast monazite deposit is located 35 kilometres south - southwest of Marvast in Yazd province of Iran. A representative sample weighing approximately 10 tons was prepared to study the amenability of the ore to physical beneficiation. The size fraction of +1000 µm was removed due to low monazite content and the –1000 µm size fraction was concentrated by the gravity-classification-magnetic methods. According to the results of sample characterization, the representative sample contains 220 ppm REO that is contained in monazite. It was concentrated to 41.5% REO by the above mentioned methods. The recovery of REO in the monazite concentrate was 41.5%.INTRODUCTIONRare earth elements are critical metals in many countries (Gupta, 2005; UK Geological Survey, 2011). Increasing application of these metals in hi-tech industries and price fluctuation caused by Chinese production policy has led other countries to focus on their local resources (UK Geological Survey, 2011). In this case, Iran is not an exception.REE mineralization in Iran is mainly located in the central zone. Regarding the exploration data, these deposits are divided into two categories. The first group is iron ore deposits in which the REE are carried by phosphate minerals. The other group is placer deposits where monazite is the major mineral of the deposit. The Marvast placer deposit is one of these types of deposit (Daliran, 1990; Mokhtari, 2008; Torab, &Lehmann, 2007; Alipour, 2014)."

Jan 1, 2016

By V. Thangadurai

The critical problems in commercialization of the present solid oxide fuel cells (SOFCs) and useful electrical and physical properties of IT-SOFCs electrolytes are discussed briefly. The conductivity behavior of the perovskite-type and perovskite-related structure metal oxides are summarized. Perovskite-type La0.9Sr0.10ao.8Mgo.203_8 (LSGM) exhibits high ionic conductivity of 0.1 S/cm at 800 °C. In order to improve the electrical conductivity of LSGM and the In analogue of LSGM, substitutions have been made at the A-and B-sites. Substitution of trivalent La3+ by isovalent Pr3+ in LSGM and La09Sro ilno.sMgo.202.85 (LSIM), yield new mixed conductors. Among the investigated compounds in the present study, La0APro.4Sro.21no sMgo.2028 exhibits the highest total electrical conductivity of 3.2 x 10-5 S/cm at 200 °C in air with the lowest activation energy of 0.44 eV (200-700 °C). LSIM and Pr-substituted LSGM and LSIM perovskites show p-type electronic conductivity in the oxygen partial pressure range 10-5 ? 0.21 atm at 750 °C. The perovskite-type solid solution SrSn1-xFex03 exhibits compositionally driven phase transitions. For example, compound of the composition x = 0 to 0.3 crystallizes in an orthorhombic GdFeO3-like perovskite structure, where as that of x = 0.4-0.9 crystallizes in simple cubic SrTiO3-like, and that of x = 1 in orthorhombic structure. The electrical conductivity of SrSn1_xFex03 increases with the increasing Fe content and reaches a value of about 10-1 S/cm at 25 °C in air for x = 1. Compounds with low Fe content exhibit both ionic and electronic conductivity, while the higher Fe content 0.5) perovskites are electronic conductors over a wide range of oxygen partial pressure of 10-22? 0.21 atm at 750 °C.

Jan 1, 2005

"These guidelines set out information on timely disclosure of news releases which are intended to provide, existing shareholders and potential investors, factual information on which a reasoned investment decision can be made.Consider the problems and concerns raised by the following hypothetical news releases:Natural Resource Company""The Company has recently optioned a large and exciting gold property near the ""XXX"" gold discovery area. In describing the property, the Company's independent consultant has said: ""The favourable location of, and some of the results of prior work done on the property give the Company a worthwhile mineral exploration opportunity .... "". The Company proposes to expeditiously conduct a sizeable exploration program on the property as soon as the appropriate financing has been arranged.""Non-Resource Company""Based on discussions with several European countries, the Company anticipates that it will have orders to ship over 200,000 crates of widgets to those European countries over the next two years. These orders, which considerably exceed the Company's forecasts for the first year, represent a projected profit to the Company in excess of $1,000,000 over the next five year period.""GuidelinesTimely disclosure news releases are intended to provide, to both existing shareholders and potential investors, factual information on which a reasoned investment decision can be made. National Instrument 43-101 Standards of Disclosure for Mineral Projects provides requirements for disclosure of a scientific or technical nature for a mineral resource company.The examples do not provide sufficient detail and are misleading because material information is omitted. The following guidelines should be observed when preparing a news release:"

Jan 1, 2003

By D. Berkley

Off-gas systems often become the limiting factor in production increase and environmental projects. Any upgrade or new off-gas project needs to address control instability issues, instabilities that can result in safety hazards, significant loss of system capacity and/or emissions to the environment [1]. In addition, the design engineer must optimize system configuration and equipment size for the new operating conditions, to have a technically feasible and economically viable project. Dynamic simulations can be used for addressing both the control stability and the design optimization issues. This paper illustrates how the dynamic simulation of transient processes and of their control system can be used in "real life" situations for these purposes, presenting the example of an electric furnace off-gas system design.

Jan 1, 2005

Agenda ?Introduction ?Geology ?Mining ?Metallurgy ?Process, Layout ?Environmental Background ?Kinross Gold Corporation owns the Lobo-Marte gold property, located in Region III of northern Chile. ?The property is close to two other Kinross mines, Maricunga 50kmto the south and La Coipa 60km to the north, plus a regional office in Copiapo and district level operating synergies are expected. ?Lobo and Marte were discovered in the early 1980s and are intrusion-hosted, porphyry-type precious metal deposits, typical of the Maricunga District. ?The Marte open pit heap leach mine was in commercial production in late 1988, but was suspended in February 1992 as it did not meet forecasted production levels and recoveries. ?Kinross plans to recover ore from the Lobo and Marte deposits through an open-pit, heap leach47,000tonne per day operation.

May 1, 2010

By V. ?. Chanturiya, G. P. Dvoychenkova, ?. Ye. Kovalchuk

"Several mineralogical investigations have revealed the composition of modified kimberlites and the mud generated during treatment of diamonds, which contains up to 50% clay minerals (e.g., talc, talcsaponite, chlorite-saponite, Na-saponite) and X-ray amorphous phase. We investigated the composition of the natural diamond surface in relation to the diagnosed minerals and established the sequence and conditions for mineral formation on the crystal surface under kimberlite processing conditions. This article suggests a method to destroy and further dissolve minerals on the crystal surfaces using water system electrolysis products, which makes it possible to restore the diamond hydrophobic properties. The application of chemically treated water in the foam separation cycle under the conditions of high recovery of diamonds made it possible to increase the content of the factory concentrate by 8.0%.INTRODUCTIONThe high content of the modified minerals in the kimberlite ore results in the formation of hydrophilic slicks on the surface of the crystals which decreases the diamond’s hydrophobic properties and increases the losses thereof in the process of grease and foam separation to 20-30% (Kurenkov, 1957; Chanturiya et al., 1998, 1999, 2005; Duikarev et al., 2000).The previous researches have revealed the fact that the prospective way of solving the problem of intensity of mineral impurities formation on the surface of the crystals and the increase of concentration parameters is reached due to application of physical and chemical stimulation techniques on the solid and liquid pulp (Stricland-Constable, 1971; “Improvement of the technology…”, 2006; Makarskii, Adodin & Tarasova, 2011; Chanturiya, Dvoychenkova & Trofimova, 2012). However, the main task of investigations to stipulate the objective achievement is the studying and justification of the reasons of the diamond surfaces covering by the mineral slicks"

Jan 1, 2016

By R. L. Every, A. G. Fonseca

"Sulphur deposition on the internal wall of a pipeline is caused by the temperature effect on the solubility of sulphur in the carrier fluid and is not due to particulate sulphur present. Deposition can be completely eliminated by proper insulation of the pipeline to prevent ""cold-spots"" and the resultant temperature gradient necessary for sulphur to precipitate from solution. Friction head losses for sulphur-condensate slurry systems are quite acceptable from a technical and economic standpoint and, in fact, are less than many present commercial slurry systems. Slurry transportation of sulphur in a hydrocarbon pipeline is a viable possibility and promises to have economic advantage over currently accepted transportation modes."

Jan 1, 1972

By K. Lambrych

Hydrometallurgical equipment used to extract and refine copper and other metals is exposed to extremely corrosive chemical environments. These systems must be fabricated from materials that are durable against corrosion, meet exacting mechanical requirements, and perform economically over the life of the mineral processing plant. In several recent large hydromet projects, fiber reinforced plastic (FRP) has been shown to provide equal if not superior durability relative to alternative materials of construction. This paper will compare corrosion performance and cost of plant equipment fabricated with corrosion resistant alloys, rubber lined steel, and FRP made with Epoxy Vinyl Ester thermoset resins. Case histories for FRP piping, storage tanks, extraction vessels, and electrowinning cells combined with laboratory-based corrosion studies will be reviewed to demonstrate how FRP materials are selected for hydrometallurgical equipment. Specific examples from projects such as El Boleo, Long Harbour and others will be used to demonstrate how the versatility of FRP allows for remote fabrication of durable corrosion-resistant large-scale equipment for hydrometallurgical refinement of copper and other metals. INTRODUCTION Fiber reinforced plastic (FRP) began to emerge as a material of construction for corrosion service in many industrial processes in the late 1950s because of its ease of use and overall performance. Corrosion resistant (CR) FRP, as an alternative construction material to alloys, rubber and tile linings, grew steadily in following decades. The aggressive operating conditions associated with hydrometallurgical processes typically require materials of construction that can withstand acids and acid chlorides at temperatures up to 90°C, sometimes higher. Common metallic materials of construction, such as carbon steel, are not compatible with these conditions. High nickel alloys are capable of meeting performance requirements, but often at a high cost. In many cases FRP mining equipment based on epoxy vinyl ester resin (EVER) offers durability, long service life and lower maintenance costs. Through demonstrated performance and decades of case histories, more and more design engineers are confidently specifying FRP as the material of construction for new mineral processing equipment.

Jan 1, 2019

By Paul Guliov

Coal-bearing Tertiary sediments of the Ravenscrag Formation in southern Saskatchewan host numerous deposits of clinker resulting from in situ coal combustion. Clinker deposits form when sediments of relatively low temperature firing properties overlie coal seams which are undergoing prolonged spontaneous combustion. The resulting fired material is useful for decorative landscaping aggregate, rock gardens, driveways, mud control and others. Predicting the occurrence of clinker deposits requires a knowledge of the spatial distribution of coal seams and the nature ofoverlying sediments. Knowledge ofpaleotopography at the time of coal combustion can assist in locating more highly-fused material which can yield greater block sizes. Coal data bases can be used as a predictive tool by outlining areas where coal is or was at or near surface and therefore may have been susceptible to spontaneous combustion.

Jan 1, 2001