Search Documents

By G. V. Fernandez

Sociedad Minera Cerro Verde S.A.A leaches secondary copper sulfides. In recent years, the mine has introduced innovations that have improved the management of mineral crushing, agglomeration, curing, and leaching. The crushing plant, for example, uses the concepts of degree of balance and percentage of time in an operationally balanced state which, displayed in real time, facilitate more intensive and uniform utilization of the crushers. High agglomerate quality is ensured with the correct dose of moisture, which is adjusted to the changing characteristics of the mineral through the use of electrical conductivity measurements. The amount of acid used for curing the agglomerate is also adjusted by using quality control information. Finally, the stockpile irrigation regime is managed using the criteria established by the "Lixiviant Request Rate", which optimizes the addition of leaching solution, creating such benefits as faster recovery, and reduced acid and energy consumption.

Jan 1, 2007

By F J. Kelly

A chemical process, based on laboratory investigations, is proposed for the production of high-purity niobium oxide from a pyrochlore-perovsk1te flotation concentrate produced from ore obtained at the Oka, Quebec property of Columbium Mining Products Limited. The method developed included the decomposition and dissolution of the flotation concentrate with hot, concentrated sulphuric acid. The dissolved niobium was purified and concentrated by a solvent extraction step, using methyl isobutyl ketone as the extractant. The niobium was recovered from the extractant with ammonium fluoride solution from which niobium oxide was precipitated with ammonia. Finally, the filtered and washed precipitate was calcined. Ninety-six per cent of the niobium was recovered in a product analysing 99.9 per cent Nzo.. The reagent cost was in the range of $1.00 to $1.25 per pound of niobium recovered. Introduction OVER the past few years, Columbium Mining Products Limited has been engaged in the development of a niobium-bearing mineral deposit in the vicinity of Oka, Quebec. One phase of this program resulted in a flotation process capable of producing concentrates containing up to 50 per cent Nb205? Flotation pilot-plant

Jan 1, 1965

By Arthur L. de Carle

"IntroductionThe Key Lake uranium-nickel deposits are located within a Mineral Lease centred at latitude 57 ° 12' north and longitude 105 °39' west along the southeastern rim of the Athabasca sedimentary basin in northern Saskatchewan, approximately 240 km north of La Ronge (Fig. 1). Access is provided by an allweather provincial highway from Pinchousc, situated about 200 km to the south, and a private airstrip maintained at the mincsitc.These deposits have been developed by Key Lake Mining Corporation on behalf of the Saskatchewan Uranium Joint Venture. Participants in the joint venture include Saskatchewan Mining Development Corporation (50%), Urancrz Exploration and Mining Limited (33 1/3 %) and Eldor Resources Limited (16 2/3 %).Considerable geological work has been conducted on the Key Lake orebodies and reported in summary papers published by Dahlkamp and Thn, (1977), Dahlkamp, (1978), Gatzweiler eta/., (1979) and Kirchner el a/. , (1980). However, intensive geological research is ongoing, particularly since many problems regarding ore genesis and controls remain unresolved . Exploration History and DevelopmentThe events (Gatzweiler eta/., 1980) which led to the discovery of the Key Lake ore bodies began in the summer of 1971 by following up on the reports of airborne radiometric anomalies and anomalous radon values in the Zimmer Lake water situated approximately 5 km to 6 km to the southwest. This work succeeded in locating a few high-grade uranium and nickel-bearing boulders associated with esker material. An integrated program, consisting of various geochemical and geophysical surveys along with diamond drilling, culminated in the discovery of the Gaertner orebody during July 1975. Subsequent fence drilling across the strike extensions of this ore structure located the Deilmann deposit, approximately I km to the northeast, in June 1976"

Jan 1, 1986

By W. J. Przybylowicz, V. M. Prozesky, D. de Bruin

"The common style of gold mineralization in the Basal Reef and other auriferous conglomerates of the Witwatersrand Supergroup comprises clusters of gold grains occurring interstitially to quartz and pyrite pebbles as well as gold accumulations attached to the surface of and infilling hairline cracks and fractures in round, compact, detrital pyrite. The latter textural association is generally interpreted as a result of remobilization of originally detrital gold during regional metamorphism and related hydrothermal fluid circulation. There is general agreement that, although gold solubility was low, ore modification occurred during the metahydrothermal event, but uncertainty exists about the magnitude and scale of gold remobilization.Micro-textural and chemical investigation of compact round pyrite and associated gold accumulation has established that gold is preferentially deposited on chemically heterogeneous pyrite surfaces. Combinations of alternating high- and low-As zones in pyrite result in mixed np-type conductivity accompanied by electron exchange and the reduction-driven deposition of gold at the cathode. This model does not explain gold accumulations which are not immediately linked to chemical heterogeneities and it is inferred that an additional control on the deposition of gold was exerted by physical defects which lead to zones of increased charge density and/or areas of focussed conductivity. The inferred precipitation mechanisms suggest that submicrocopic physical and chemical controls are the important factors that determined the sites of gold nucleation and that precipitation mechanisms based on physicochemical changes of the hydrothermal system were not involved. The Basal Reef contains on average close to 5OJo of round, detrital, chemically zoned pyrite which provides a large number of electrochemically active pyrite surfaces. The extremely effective electrochemical precipi- . tation mechanism together with the low solubility of gold in Witwatersrand fluids is the main reason for the spatially restricted remobilization of gold in the conglomerate reefs."

Jan 1, 1994

By Yang Shuxin, Guo Qiliang, He Ping, Lu Lizhi, Yao Rui

"We combined stepwise regression and constrained regression statistical method to obtain the best boundary conditions for the calculation of in-situ stress field in Wushaoling tunnel using finite element method. Our numerical results reveal that: the main geologic factors contributing to the initial background stress are gravity and tectonics; the principal stress values would drop in fault zones; the angle between the maximal horizontal stress and the axis of Wushaoling tunnel is acute; Wushaoling tunnel tends to become stable when this tunnel has 2:1 ratio of the height to its width; the possibility of rock-burst exists under high stress.INTRODUCTIONStress state of engineering region is an important factor affecting the stability of project. Geological disasters in the project area are closely related to their stress environment. Wushaoling tunnel which is 20,050 meters long, lying along Lanzhou-Wuwei segment of Lan-Xin Railway in China, is the key project of Lan-Wu double-track railway. The region surrounding this tunnel is under a high stress environment. Accurate identification of the stress environment of the engineering area and the interaction between geomaterials and geotechnical engineering construction holds significant scientific and practical value for engineering design, construction, and operation.Many scholars explored and discussed the present-day tectonic stress through investigations of tectonic evolution history (Ding, & Lu, 1986), crustal deformation (Zoback, 1992), focal mechanisms (Yang et al., 2003, Xie, Cui, & Zhao, 2004), and so forth. However, the above methods would only provide the approximate direction of the principal stress in a broad region, and could not give the absolute stress values. In-situ stress measurement is one of the primary means to directly gauge the current crustal stress. However, in-situ stress measurement can only be applied in small number limited by measurement conditions."

Jan 1, 2015

By J. Keith Seidler, David R. Lentz, Douglas C. Hall, Nicholas Susak

Abstract - The Ta-Nb-Zr-REE-rich McKeel Lake alkali granite pegmatite-aplite dike swarm is hosted within the late Silurian multiphase alkali granite intrusion (Welsford) near Browns Flats in southwestern New Brunswick. A steep easterly dipping series of pegmatite-aplite dikes trending 170º can be traced 150 m along strike; they are up to 40 cm wide, closely spaced (10-20 cm apart), and interconnected by narrow branching dikelets that generally trend perpendicular to the overall strike direction. The Welsford intrusion has mantle A-type affinities characterized by enrichment of Zr, Ta, Nb, Th, and rare earth elements (REE). Two separate sets of dikes have been identified: (1) an unmineralized fine-grained porphyry, which occurs at depth and seems to be the youngest intrusive phase; and (2) a mineralized pegmatite-aplite dike swarm (419 ± 20 Ma) that crops out at surface. The mineralized pegmatite-aplite dikes likely represent a late magmatic, highly fractionated phase of the Welsford intrusion. XRF and INAA data indicate that the Welsford intrusions and related pegmatite-aplite dikes show elevated levels of Ta (74-220 ppm), Nb (750-3,040 ppm), Zr (1,450-36,000 ppm), Y (540-3,070 ppm), Th (170-870 ppm), U (60-250 ppm), Ce (430-1,950 ppm) and Yb (110-290 ppm). Electron microprobe analysis of two samples identified Ta-Nb- and REE-rich phases: euxenite, fergusonite, aeschynite, (Y)-aeschynite, and a REE carbonate.

Jan 1, 2005

By F. Prescott, D. Hiam-Galvez, J. Hiam

Mines are frequently located in remote areas with little conventional employment and few opportunities for the existing population. The development and operation of the mines results in several years of intense activity followed by a near-complete reduction in employment and opportunities after the mines are closed. Designing Sustainable Prosperity (DSP) is a method for rectifying this situation by designing for long-term growth in areas that host mines. This process involves the participation of local and national governments, local community, mining companies, investors, academics and those with sector expertise. The mines will be the catalyst for regional sustainable development. If successful, long-term economic and environmental prosperity should be the result for the areas affected by mining and, in some instances, promoting the regions as centres of excellence for a particular industry. This paper will describe how the concept works using the copper producing region of Peru and Chile as an example. Designing sustainable prosperity starts by looking at regions based on the natural resources and skills available, the infrastructure and possible energy sources. Integrated natural resource models and innovative market studies, followed by education and skills requirements, are then established to determine the potential for the region and what needs to be done to realise the possibilities. INTRODUCTION Industry 4.0, or i4.0, dubs the fourth and current industrial revolution. Where previously they have been founded on ever-increasing consumption and production, i4.0 distinguishes itself by its partial focus on reducing resource intensity; lightweighting, energy efficiency, sensors and automation to improve resource efficiency. Industry 4.0 is an era of artificial intelligence, genome editing, biometrics, renewable energy, 3D printing, autonomous vehicles and the Internet of Things (Lu, 2017). These drivers represent key opportunities for the economic future of nations and regions.

Jan 1, 2019

By D. R. Lentz, J. A. Walker

"Abstract -The Flat Landing Brook Zn-Pb-Ag deposit of the Bathurst Mining Camp occurs within a narrow thrust-bound nappe containing felsic volcanic and volcaniclastic rocks of the Tetagouche Group. Within the host nappe, the Tetagouche Group is represented by the Nepisiguit Falls Formation and the overlying Flat Landing Brook Formation. The Nepisiguit Falls Formation is divided into two members: quartz- and quartz-feldspar-phyric volcaniclastic rocks ± minor lavas (Grand Falls member), and aphyric, fine-grained volcaniclastic rocks (Little Falls member). The Flat Landing Brook Formation consists of aphyric rhyolite flows and interbedded pyroclastic rocks. Several gabbroic intrusions occur in both the footwall and hanging-wall sequences. These gabbros locally cut out the mineralized horizon at shallow levels, and are considered to be feeders to tholeiitic basaltic flows (Forty Mile Brook member) of the Flat Landing Brook Formation. The Flat Landing Brook deposit has many of the characteristics typical of volcanogenic massive sulfide deposits occurring within the highly productive Nepisiguit Falls Formation in the eastern part of the Bathurst Mining Camp. Mineralization occurs within or at the top of the Grand Falls member and comprises four or more massive to semi-massive sulfide lenses that vary in thickness between 3 and 5 m. Massive lenses are laterally gradational to, or underlain by, zones of disseminated sulfides up to 38 m thick. The deposit contains an estimated resource of 1.7 Mt grading 4.9% Zn, 0.94% Pb, and 19.54 g/t Ag to a depth of approximately 150 m. From 150 to 300 m below surface, mineralization is low grade and mostly disseminated. However, below 300 m, ore-grade (>10% Pb+Zn) massive sulfide lenses have been intersected over mineable widths. Oxide facies iron formation overlies and (or) grades laterally into the sulfide lenses. The oxide facies has strong positive Eu anomalies and gently sloping rare earth element (REE) profiles suggesting that it was formed from relatively hot acidic fluids that had interacted with felsic volcanic rocks in the footwall. In contrast, the silicate facies iron formation that is more distal to sulfide accumulations has very weak positive Eu anomalies and gently sloping REE profiles, suggesting either cooler hydrothermal fluids or dilution of the hydrothermal component by detrital material. Hydrothermal alteration has affected most footwall rocks. Most notably, albite-destructive alteration has resulted in Na2O depletion, whereas mass addition of K2O is manifested in the formation of sericite (white mica). In more intensely altered quartz- and feldspar-phyric volcaniclastic rocks of the Grand Falls member, feldspar destruction is accompanied by chlorite alteration, producing quartz-phyric rocks similar to those in the footwall of many Bathurst Camp deposits."

Jan 1, 2006

By A. W. Lovett

"THE last two years have been years of recession or, perhaps, years of marking time, depending upon whether the observer is a pessimist or an optimist. There has been a slackening in the industrial tempo that has been reflected in many ways in the national economy. As one of the chief barometers of economic health, the consumption and supply of energy reflect this slowing up.These same two years have also seen significant changes in the relation between the sources of energy. In periods of declining demand, it has happened in the past that coal, as the basic or residual source of energy, has shown the effects to a greater extent than the other energies. In these two years, however, in addition to this usual effect, there has been the acceleration in the Joss of market to diesels in the railway consumption category and the continuing decline in domestic consumption. The story of these years is presented in the statistical tables that form the foundation of this paper. Statistics, particularly in the form of tables, are rather dry and are sometimes difficult to follow but the overall developments are illustrated by graphs which present a more striking picture."

Jan 1, 1959

By M. B. Kime, E. K. Kanowa

"Heap leaching of low-grade copper-cobalt oxidized ore and solvent extraction of copper, cobalt, manganese, and zinc were investigated. Heap-leaching parameters were optimized using agitated and tray batch leaching tests, capped by tests on a pilot semicontinuous heap-leach plant. The optimum pregnant leach solution yielded 2,350 mg/L Cu, 3,800 mg/L Co, 3,600 mg/L Fe, 130 mg/L Mn, 25 mg/L Zn, and 0.58 g/L solids in suspension, with pH and acidity of 1.27 and 3.66 g/L, respectively. Copper, cobalt, and impurities (Mn and Zn) were extracted using (v/v) 30% CP-150, 20% IONQUEST® 290, and 20% D2EHPA, respectively; overall recoveries of copper, cobalt, and impurities were 98, 99, and 70%, respectively.RÉSUMÉ La lixiviation en tas des minerais oxydés de cuivre et de cobalt et l’extraction par solvant du cuivre, du cobalt, du manganèse et du zinc ont été étudiés. Les paramètres de lixiviation en tas ont été optimisés à l’aide d’essais de lixiviation en discontinu sur un plateau, complétés par des essais relatifs à une usine pilote de lixiviation en tas en semi-continu. La liqueur-mère optimale a produit 2 350 mg/L de Cu, 3 800 mg/L de Co, 3 600 mg/L de Fe, 130 mg/L de Mn, 25 mg/L de Zn et 0,58 g/L de solides en suspension, avec un pH et une acidité respectifs de 1,27 et 3,66 g/L. Le cuivre, le cobalt et les impuretés (Mn et Zn) ont été extraits avec un pourcentage volumique (v/v) de 30 % de CP-150, de 20 % d’IONQUEST ® 290 et de 20 % de D2EHPA, respectivement. Les récupérations totales de cuivre, de cobalt et d’impuretés étaient de 98 %, 99 % et 70 % respectivement.INTRODUCTIONBoss Mining S.P.R.L. is a privately owned hydrometallurgical plant located in southeastern Democratic Republic of Congo. It treats oxidized ores of copper and cobalt that are recovered by sulphuric acid heap leaching (Trujillo, Cisternas, Gálvez, & Mellado, 2014; Kime, Kanowa, Mulaba- Bafubiandi, & Diyambi, 2016) and solvent extraction processes (Crane, Urbani, Dudley, Horner, & Virnig, 2009; Fisher, 2011; Kime et al., 2016). The ore to the plant is primarily sourced from the Luita and Mukondo mines. Geological prospecting work by Gecamines and Boss Mining showed that the Mukondo mine contains a very large cobalt reserve not yet exploited, but with grades as low as 0.2%.Currently, Boss Mining is focusing on the production of copper, but is investigating methods to efficiently produce both copper and cobalt. A challenge in the production of cobalt from this ore is its presence in the third oxidation state. This requires the addition of reducing agents, which increases the overall operating cost (Kime & Makgoale, 2016). Cobalt solvent extraction is also very sensitive to impurities such as nickel, zinc, manganese, and aluminum, which are often co-extracted (Swartz, Donegan, & Amos, 2009). This sensitivity to impurities requires the optimization of operational parameters to lower impurity levels as much as possible in the electrolyte."

Jan 1, 2017

By C. R. Powell, W. H. Maher

"This paper presents a short history of the development of milling at Buchans, Newfoundland, and a description of the operation.History and DevelopmentTHE original ore discovery was made at Buchans in 1905 by Matty Mitchell, a Micmac Indian who was prospecting for The Anglo Newfoundland Development Company, which company was then preparing to build a paper mill at Grand Falls, some 50 miles east of Buchans. A development program, initiated in 1906, was terminated in 1911 because of metallurgical difficulties. Intermittent testing was carried out by The American Smelting and Refining Company, and in 1925 a satisfactory method of concentration by flotation was found. Following this, intensive geophysical reconnaisasnce, succeeded by diamond drilling, uncovered two additional orebodies similar to the original discovery at Buchans River."

Jan 1, 1966

This paper describes the results of a laboratory study on the upgrading of Algoma siderite by the amine flotation of silica and silicate gangue. The experiments indicate that a virtually complete removal of silica is possible in a rougher flotation con-ducted in tap water at natural pH, without prior desliming of the ore. Grinding considerably finer than the apparent liberation size is essential for maximum silica rejection. A cationic collector, Aeromine 3037, gave best results when used in combination with a modifier. Of the several modifiers tested, a Dutch potato dextrin, Dextrin 4356, was found to be the most effective. Both iron recovery and the grade of the final iron product are enhanced by floating the pyrite contained in the ore prior to the amine flotation of the silica, and by scalping the magnetics from the silica concentrate. F OR over twenty years, the Algoma Ore Properties Division of The Algoma Steel

Jan 1, 1963

By A. Galip Ulsoy

This review paper is intended to provide, the mineral process engineer with an introduction to the concepts, terminology and practice of mineral process control. It also provides an extensive sampling of the vast body of literature relevant to this topic. The topics discussed include the principles of automatic control, instrumentation, mineral processing unit operations, process modeling and simulation, and process and plant control.

Dec 1, 1981

By K. Esmaieli

This paper addresses issues associated with ore pass degradation caused by material impact. A series of numerical experiments, using the particle flow code, were undertaken to investigate the influence of various finger raise configuration. This has allowed the identification of favorable configurations. The results of this analysis, when coupled with field observations, can contribute to the design of ore pass systems that can prolong the useful operating life of ore pass systems.

May 1, 2009

By G. H. Agnew

When water floods are initiated after gas-oil ratios have increased, the transition period from the start of injection until" the gas-oil ratios are returned to the solution gas-oil ratio may be important for either economic or technical reasons. The transition period is longest, and consequently most critical in water floods where injection is equal to withdrawals. This paper describes a theoretical basis for predicting the behavior of such a system and outlines a procedure for making the necessary calculations. The calculation procedure is illustrated for two actual cases: a line drive water flood and a five spot water flood. In each case there is a reasonable similarity between the actual and calculated performance.

Jan 1, 1960

By Imane Benhamed, Jaouher Diouani, Laurent Cassayre, Florent Bourgeois, Carine Julcour-Lebigue, Université de Carthage

The attrition-leaching process aims at improving leaching performance when formation of passivation layers at the surface of leached particles is a severe limiting factor, as discussed recently by Julcour and coworkers (Julcour et al., 2015). This paper proposes a geochemistry-based modelling scheme for deriving the window of possible operating conditions for the attrition-leaching process to match the properties of the processed ore. The rationale is that the attrition-leaching process maintains the surface of reacting particles in an unpassivated state by continuous mechanical removal of surface leach layers, so that the process reactions can be modelled from thermodynamic equilibria throughout the duration of the process. The strength of the proposed modelling approach is that it bridges the gap between the properties of the ore and the process operating conditions. The present paper exemplifies the proposed process modelling route for derivation of the attrition-leaching process operating conditions in the context of the leaching of silicate ores, matching model predictions against controlled laboratory experiments. It is shown how thermodynamic modelling, when used in conjunction with a solid knowledge of the phases present in the system, can assist with deciding upon suitable process operating conditions. As an example, this firstprinciple modelling approach predicted that steel grinding medium would be converted into siderite (FeCO3) under a wide range of operating conditions, which led to questioning this initial choice of grinding medium for the attrition-leaching process under mineral carbonation conditions. It is emphasised that the same approach could be applied to ores of greater economic significance.

Jan 1, 2016

By R. Howard

"In projects involving resource development and plant optimization, the use of in-mine geophysics can deliver considerable benefit. The value proposition lies in using very high resolution downhole measurements to model process-plant outcomes. The calibration procedure used to convert in-situ physical properties into process engineering parameters is illustrated using two iron ore projects. Data correction was related either to orebody structure or mineral formation. The deliverable from this approach is a series of high-definition sections indicating the variability of ore delivered to a front-end separation plant and parameters for mine scheduling and stockpile design needed for maximum product yield.RÉSUMÉ Dans des projets de développement des ressources et d’optimisation de l’usine, l’utilisation de la géophysique minière peut engendrer des bénéfices considérables. La valeur de la proposition réside dans l’utilisation de diagraphies à très haute résolution afin de modéliser les résultats de l’usine de traitement. La procédure d’étalonnage utilisée pour convertir les propriétés physiques in situ en des paramètres d’ingénierie de procédés est illustrée en se basant sur deux projets de minerai de fer. La correction des données porte sur la structure de la masse minérale ou de la formation minérale. Les livrable attendus de cette approche sont une série de sections à haute définition, signalant la variabilité du minerai livré à une usine de séparation de première ligne, des paramètres pour l’échéancier de la mine et la conception des haldes requis pour une production optimale."

Jan 1, 2016

By F. McGravie, S. T. Solinski, W. W. Robertson

During this, the Centennial year of the discovery of the Hall-Heroult process, it seems appropriate to review some of the developments which have taken place in Canada and to explain why it has become an important world centre for the production of primary aluminum. For many years after it was recognized that the element aluminum existed, scientists were frustrated in their efforts to isolate it. In the early 1800s H. C. Oersted and Frederick Woehler prepared small quantities sufficient to measure some of the physical properties. A quasi-commercial process involving reduction with metallic sodium was developed by the French scientist H. St. Claire Deville in 1855 but the cost was very high ($30. 00 per kg). It was not until 1886 that Charles Martin Hall in the United States and P.L.T. Heroult in France, more or less simultaneously but completely independently, discovered the process which is essentially that in use today. Some of the early pioneers in the industry quickly recognized the potential of the hydro-electric resources in Canada as economic energy suppliers for aluminum production. The first commercial production in Canada was in Shawinigan, Quebec in 1901, only 15 years after the process was discovered. Subsequently operating plants were established at nine different locations in Canada (Quebec and British Columbia) (Table 1). Operations continue today in all locations except one (La Tuque). The table shows present plant capacity which for the older plants was reached in an evolutionary manner including replacement of obsolete capacity or upgrading and modernization of existing designs.

Jan 1, 1999

By Z. S. Shao, X. Z. Li

"Sub-critical crack growth plays an important role in long-term creep failure in brittle rock. Based on micromechanics established by using relationship between micromechanical wing crack growth model and macroscopic strain, and comparing theoretical model with testing results, a method, which applies the theory to real rock, is suggested in this paper. Using this method, properties of creep, damage and progressive failure in brittle rock are investigated. Effects of stress state on creep failure time and steady-state creep rate are analyzed and graphically presented. The results are helpful to support structure design and service life evaluation of underground structures with high geostatic stresses. INTRODUCTIONDuring the long-term operation in underground space with brittle surrounding rock, due to chemical action between pore water and rock, the failure of rock often occurs at stresses below its short-term failure strength, which brings serious effect on the long-term stability of underground structure. Thus, the long-term strength of brittle rock attracted wide interests of scholars around the world. The static fatigue limit was predicted by exponential function that is derived from abundant experiment data of stress level and failure time(Schmidtke & Lajtai, 1985), and similar result by relationship between stress state and failure time was also suggested (Lau & Chandler, 2004; Aubertin et al., 2000; Sangha & Dhir, 1972). According to relationship between steady creep rate and stress state during creep, a critical stress that transforms steady-state creep to accelerated creep was studied and the long-term strength was suggested (Tsai et al., 2008; Ma & Daemen, 2006; Lajtai et al., 1991). Based on the results of experiment in compression, the long-term strength of rock was defined by stress at volume strain reversal. When applied stresses are larger than the long-term strength, the microcracks in the rock will grow constantly, damage of rock will increase and failure of rock will occur finally (Chandler, 2013; Bieniawski, 1967; Brace et al., 1966)."

Jan 1, 2015

By J. Desroches, J. Burghardt, B. Lecampion, A. P. Bunger

"We present detailed comparisons between theoretical predictions and experiments for the initiation of radial hydraulic fractures transverse to a wellbore. Most of these experiments provide a measure of the time evolution of pressure, length, opening and flux entering the fracture during the test. We compare all these measurements simultaneously to our theoretical predictions, thoroughly testing hydraulic fracture initiation theory, which is shown to be predictive. These comparisons notably emphasize the difference between the initiation pressure (the wellbore pressure for which the fracture initiates) and the breakdown pressure (a misnomer which simply corresponds to the maximum pressure recorded during the test). INTRODUCTION In this paper, we will compare hydraulic fracturing laboratory experiments performed in different tight materials (PMMA, cement, shale) with the predictions from a numerical solution of the governing equations of hydraulic fracture mechanics (e.g. Geerstma & de Klerk, 1969; Detournay & Peirce, 2014). We focus on transverse radial hydraulic fractures initiating from a radial notch at the wellbore wall (see Figure 1). In particular, we will clarify the difference between the initiation pressure (the wellbore pressure at which the fracture initiates) and the breakdown pressure (a misnomer which simply corresponds to the maximum pressure recorded during a test, usually carried out at constant pump rate). This difference stems from the strong viscous effects at play during wellbore pressurization, fracture initiation and early propagation (i.e. fluid entrance in the newly created fracture). It has been observed on a number of experiments (e.g. Weijers, 1995; Zhao et al., 1996) and has a strong practical application, first because the maximum pressure is the most obvious value to report and second because that maximum value is necessary to specify injection systems."

Jan 1, 2015