Search Documents

By R. W. Culley

"In many areas of Saskatchewan, known gravel deposits have been depleted or are diminishing rapidly; in other areas, particularly in the north, demands for all-weather highways and access roads are far exceeding the supply of gravel sources with which to surface them. These two problems have made conventional methods of air-photo and ground surveys insufficient for gravel location. In the first case, hauling costs on construction now warrant searching for buried deposits and for smaller, less obvious surficial deposits that may be closer to the project. In the second case, search and access conditions are so difficult and costly that the ratio of successes to failures must be kept very high. The Department of Highways has long been aware of the oncoming scarcity of quality gravel deposits and is continually investigating ways of forestalling it. One of these ways is the use of airborne geophysical methods that permit rapid coverage of large areas and that sense and discriminate between earth properties to a significant depth below ground surface. In 1967, the Department began an investigation of an airborne conductivity survey method called INPUT*, or ""Induced Pulse Transient'', leading to a trial in 1968 and data analysis in 1969. The results of this trial initiated• modifications to the technique to improve its sensitivity for mapping shallow deposits. Part way through this modification in 1970, a decision was made to change to an airborne resistivity survey method called EPHASE*. Trials with this technique were conducted and analysed in 1971. This paper is an explanation of the E-PHASE system and a summary of the results from one of three areas mapped in 1971."

Jan 1, 1973

By O`Donnell. P. J.

THE modern coal cutter is a highly developed, and to a certain extent a somewhat complicated, machine. The requisite power to cope with conditions as found must be generated by the motor with due regard to limitations in the matter of dimensions and weight. This imposes the necessity of relatively high speeds of rotation. Any factor external to the machine proper which tends to reduce the load on the motor and gearing is most important. Experience has proved that close attention to the question of cutter-chain details undoubtedly results, in practically every coal-cutting operation, in increased efficiency and reduction of power and maintenance costs. The chain is the unit of the coal cutter which most greatly affects the economical operation of the machine, and only by due consideration of conditions and by the proper selection of the right chain can best results be expected; also, intelligent care of the chain while in operation is essential if it is to give its best service. The chain is the part of the machine that carries the pick boxes or blocks, which are connected to each other by a pair of chain links. The power to drive the chain is trans-mitted by a sprocket. The chain runs in guides supported by a rigid member called a 'jib'. Figure 1 shows the various parts mentioned. The first requirement of a chain is that it cut the coal as fast as possible. The second is that it do so economically. Economy of cutting can conveniently be divided as follows: (1) Economy in power used. (2) Economy in pick life. (3) Economy ' in chain life. ( 4) Economy in jib life. (5) Economy in labour for maintenance.

Jan 1, 1936

By Colleagues from Process and Operation departments, Guy Chevalier

"QCM's pellet plant, located in Port-Cartier, Quebec, produces up to 8.6 million tons of iron ore pellets annually. Four different types are produced: three for blast furnace operations and one for direct reduction furnaces. The paper presents the scientific approach that led to the installation of new process equipment to improve the reducibility of direct reduction pellets (DR pellet). The findings, the equipment selection and some post start-up modifications are presented.This low silica DR pellet is used in Midrex and HyL shaft furnaces. A good DR pellet has to meet strict chemical, physical and metallurgical specifications. An important metallurgical property is its ability to release oxygen when exposed to reducing gases. Considering that the market for DR pellets is expanding and being aware that reducibility is critical for our clients, a program to improve the latter was undertaken. Test work showed that one factor which has a negative effect on reducibility is the proportion of particles larger than 75 microns. Knowing that the best way to reduce the amount of coarse particles was to close our open grinding circuits, we began evaluating the most suitable classification equipment applicable to our process operations. We settled on hydro-classifiers based on their very sharp cut and their low operating costs. In light of the hydro-classifiers performance it was also decided to replace the hydro-cyclones of an already closed circuit.INTRODUCTIONAt the Québec Cartier Mining pellet plant, continuous improvement programs are aimed at increasing levels of consistency and improved chemical, physical and metallurgical properties. This is being accomplished while still maintaining pellet plant production volumes to satisfy market demands.QCM produces three types of pellets for blast furnace use: acid pellets, designated as ""BHF"", fluxed pellets, designated as ""BAF"", and low silica fluxed pellets, designated as ""BSA"". For direct reduction, a low silica acid pellet or DR pellet, designated as ""BBS"" is produced. This low silica DR pellet is used in Midrex and HyL shaft furnaces.The demand for DR pellets has been increasing during the last few years and is believed to continue so in the future. Wanting to be present in this growing market QCM found that it would be essential to work at improving its DR pellets quality. Efforts have been focused on improvements in three areas: SiO2 reduction, elimination of sticking and increasing reducibility. Improvement programs have begun with laboratory research followed by plant trials and full-scale implementation as a cooperative effort among QCM, COREM, and key customers."

Jan 1, 2002

By R. S. Jones

"Fording Coal Ltd. is now in its fifth year of a 15-year contract to supply 3 million long tons of clean coal per annum to its Japanese steel-making customers. The mine employs both conventional truck-shovel and unconventional ""walking"" dragline coal mining techniques in multiple-seam pits. This paper describes the present and future application of the 60-cu.-yd dragline and truck-shovel pre-stripping fleet in 1•ecovering 5- to 40-footthick coal seams in mountainous terrain. Deep blastholes, coal flow demands, spring ""run-off"", seam and inter-seam thrust faulting, limited seam outcrop data and regional faulting are a few of the problems encountered in this application. The author discusses these problems and their solutions as applied at Fording Coal Ltd."

Jan 1, 1976

By F. Vahdatikhaki

Simulation techniques have offered significant boosts toward a cost-and-time-optimized planning of construction projects by enabling project managers to effectively comprehend the behavior of projects. Using historic data from projects of like nature, simulation considers uncertainties involved in a project through accommodating the stochastic modeling parameters. However, the heavy reliance on the statistical data and not taking into account the context-specific features of the project cause the degradation in the realism and accuracy of the simulation models. Similarly, the extent to which a historic pattern could be retrofitted to new projects will decrease in line with the growing uniqueness of the projects and the novelty of construction methods. Furthermore, the existing real-time simulation frameworks are not capable of distinguishing the transient environmental changes, with minimal long-term impacts on the productivity, from the influential changes that will greatly impact an operation. In addition, existing simulation tools are devoid of location awareness, resulting in the inability to consider safety threats in their representation of the project. To address these issues, this research proposes a framework based on the integration of new tracking technologies used in Automated Machine Guidance (AMG) with simulation-driven 4D modeling methods. The proposed framework automates the adjustment of the simulation model based on the updated data from the site, and thus transforms simulation from a predictive tool used at the planning phase to a proactive monitoring platform usable throughout the planning and construction phases. A prototype is developed to test and demonstrate the effectiveness of the proposed approach.

Aug 1, 2013

By Toivo Toivanen

The paper begins with a brief history of the nickel industry in Finland, and then deals with the introduction of the flash smelting process. The main part of the paper is devoted to nickel refining, which is studied under four main headings -grinding, leaching, electrolyte precipitation, and nickel electrowinning. Flowsheets are illustrated, and the equipment used is described. Analyses of the material in the various stages, from concentrate to high-grade nickel matte, are also presented. N ICKEL made its appearance in the Finnish mining industry forty years ago, when a nickel deposit was discovered at Petsamo in Lapland. Mond Nickel Co. received the concession for this deposit from the Finnish Government, and the Petsamon Nikkeli Company constructed a mine and a nickel smelter (1), the completion of which was prevented by the 1939 Winter War. The mine and smelter were, however, completed soon afterwards in spite of World War II,

Jan 1, 1964

By Marc Boyer

Modern civilization, modern industry, and modern standards of living, bring into, sharp relief the present-day essentiality of metals .and minerals, and the wide and diversified use which is made of them. Any attempt, therefore, to appraise the international situation today must take into consideration the metal and mineral resources of the world. If, as some believe, the world is divided into two distinct ideologies of political belief, one unalterably opposed to the other, so that armed conflict is unavoidable, then the question of national strength in mineral resources becomes of paramount importance. If, however, it is possible to avoid war by raising the standard of living in the underdeveloped ?areas of the world, thus ensuring all peoples everywhere against the dread spectres of starvation and disease, then the development of the world's mineral resources assumes even greater importance. Today it is difficult to realize that, prior to the industrial revolution in Great Britain, only a few of the metals and minerals now in common use entered into the everyday life of the people. !iron and steel, copper, lead, tin, and zinc, usually in .their unalloyed forms, along with the more common industrial minerals, were those most widely used, and then only in limited amount. With the advance of technology in metallurgy and in fabricating skills, the list of commercial metals and minerals has expanded until today they number more than eighty.

Jan 1, 1951

By B. D. Sparks, I. E. Puddington, F. W. Meadus

The continuous separation of bitumen from Athabasca tar sands, with a high clay content, has been demonstrated. Recoveries of 95 per cent or higher have been obtained. Further processing of this product, to produce an accept-able type of crude oil, would require less heat than currently used in the hot-water process. Also, by comparison, substantial savings in equipment and operating costs are indicated.

Jan 1, 1971

By Alfred C. Lane

Reference to the original use of the terms Laurentian and Huronian (and its extension), shows that the former was applied to granitized sedimentary and metamorphic pre-Cambrian rocks, and the gneissoid igneous rocks associated therewith, and the latter to non-fossiliferous rocks supposed to be later. But it appears from the work of Collins, Quirke and others that there is more or less of an overlap, and that of the original Laurentian the Grenville limestone, and some of the granites, may be later than the lowest part of the original Huronian. Before we can decide whether to abandon one or the other of the two terms, or how to delimit them, it is important to know the extent of this overlap. The Pb :U ratio, though not to be depended upon too minutely, does give a real idea of the age of a mineral as it increases with the decay of uranium, and so is greater the longer the time since the uranium was separated: and there are reasonable prospects of help there from in getting a knowledge of the relative age of different granites to assist in solving the problem, as facts already collected show. 1. Historical review of the use of the words Laurentian and Huronian: 2. Difficulty encountered: 3. Popular account of atomic disintegration: 4. Methods of estimating age by it: 5. Applications.

Jan 1, 1925

By Lucien Piché

"IN any opportunity such as I am now given, I suppose that one should not fail to say that what the world has to offer to this year's graduates in science and in engineering is the greatest promise ever held out. High-ranking new scientists and engineers -particularly those with the Ph.D. degree -find themselves in an apparently delightful situation; the glow of attention that surrounds them and the dazzling starting salaries that are offered to them may indeed be turning their heads a bit and the attitudes of some of them are sometimes expressed with a smugness that can find its equivalent only in freshmen. On the average, however, the new graduates are, without any doubt, the best trained ever, or at least they have been the most expensive to train in the universities.There appear to be exciting opportunities for competent, well-trained and educated scientists and engineers far beyond the numbers that can be annually produced, and the demands for excellence in depth as well as in breadth of training probably will continue to increase for many years to come. The problem is visible all around us in Canada that there is much more money to buy brains than there are brains to be bought."

Jan 1, 1966

By R. W. Brock

This subject is too broad and comprehensive to be dealt with adequately and authoritatively in this paper. It calls for the knowledge and experience of many men, but the results from such collaborative effort would be of great value, particularly if similar reports of the principal mining districts of the world were made on a standardized basis so that conditions everywhere might be directly and accurately compared. In considering conditions affecting mining in British Columbia, unfavourable as well as favourable factors must be taken into account. The unfavourable are apt to loom large and to be exaggerated rather than minimized; for it is human nature to see the blackness of the cloud rather than the silver lining; to think that one's own undertaking is beset with peculiar difficulties, and to attribute lack of greater success to out-side causes rather than to personal shortcomings. It should be recognized, however, that there is no country where the conditions for mining are ideal. The ideal mining country is the product of imagination, invested with every favourable condition found anywhere, but with none of the unfavourable conditions that are always present in reality. So if British Columbia has some handicaps to the industry, it is in good company. What is important is that the advantages compensate for the disadvantages, that the balance will compare favorably with that of competing states, for mining, like every other industry is competitive, and the cost of one's product must have a definite relationship to its price in the world's market.

Jan 1, 1924

By N. F. Faria, F. Monteiro, B. O. Taiwo, A. Palangio, D. Fonseca, J. Manuel

This paper explores the interpretation and application of Particle Size Distribution (PSD) curves in optimizing blast design and enhancing downstream operations. The study looks at important factors like D50, D80, fines content, and the uniformity index to show how PSD curves affect the efficiency of different mining processes. The first section of this paper discusses the impact of blast design parameters such as burden, spacing, and explosive energy on the resulting PSD, highlighting their significance for downstream operations like crushing, and material handling. The section concluded that proper alignment of PSD with downstream size classes, like primary crusher inlet sizes, among others, can result in substantial cost reductions and productivity gains. The second part presents a case study from dstgroup aggregate quarry in northern Portugal, utilizing fragmentation analysis to evaluate blast performance and promote continuous improvement. The section specifically examines the effect of stemming material size on blast fragmentation, comparing the impact of using aggregate with a D80 of 12.32 mm versus a D80 of 21.94 mm. The D80 value represents the particle size at which 80% of the stemming material is smaller, making it a critical parameter in evaluating the stemming's effectiveness in confining explosive energy. The drilling and blasting designs were meticulously planned using O-PitDev and O-PitSurface software to ensure accuracy in blast parameters and layout. To assess the fragmentation resulting from these different stemming material sizes, the study utilized WipFrag 4 software. The software allowed for precise measurement of particle size distribution after the blast, as well as a detailed comparison between the two stemming sizes. Results from the analysis indicate that using bigger-sized stemming material led to improved blast confinement, which in turn resulted in better fragmentation compared to the smaller-sized material. The reviewed blast videos demonstrate that the larger aggregate effectively contained the explosive energy within the borehole, thereby reducing premature venting and directing more energy towards breaking the surrounding rock mass. This led to finer fragmentation with D80 = 1240.1 mm, D50 = 685.9, and Dmax = 2580 mm, which is advantageous in downstream operations like crushing and milling. On the other hand, the smaller stemming material (D80 = 21.94 mm) did not confine the explosive energy as efficiently, resulting in coarser fragmentation (D80 = 1327.37 mm, D50 = 750.76, and Dmax = 2370 mm) and reduced overall blast efficiency. These findings highlight the significant influence of stemming material size on blast performance and fragmentation outcomes. 

May 4, 2025

By D. Karpoff

"IntroductionUNTIL the recent discovery and development of deposits at Allard Lake, on the Lower Romaine river, practically the whole of Quebec's - and indeed of Canada's - production of ilmenite had come from deposits in the vicinity of St. Urbain, Charlevoix •county, a village about eight miles north of Bay St. Paul on the north shore of the St. Lawrence, some sixty miles below the city of Quebec (see Figure l) . Although these deposits were known nearly three hundred years ago and were worked in a small way during the years 1872-74, when a charcoal blast furnace was operated by the Canadian Titanic Iron Company for making white pig iron, it was not until 1908 that more or less continuous production commenced and has •continued to the present by the American Titanic Iron Company. The whole of the output has been exported to the United States.The ilmenite occurs in lenses •and dyke-like bodies within anorthosite. Production has come chiefly from three deposits: General Electric, Furnace, and East and West Coulombe. During 1951 -52, an extensive diamond drilling programme was carded out under the direction of the writer to test the Furnace and the East and West Coulombe deposits (Figures 2 and 3), which form part of the property of St. Lawrence Iron and Titanium Mines, Limited. The average tenor of the orebodies encountered in the course of the drilling was 38.60 per cent TiO2 and, in addition to these high-grade •bodies, there was found a very considerable tonnage of lower grade ore."

Jan 1, 1953

?Four-wheel, skid-steer, rover developed for CSA ?U-chassis for payload accommodation ?Passive geometric suspension ?Max speed 13km/hr ?Remote workstation ?275kg payload capacity ?On-board processor, IMU, motor encoders ?5.2kW-h battery capacity

May 1, 2013

By Frederik H. Kriel, John Ralston, Craig Priest

"Stream-based microfluidic solvent extraction offers a novel alternative to bulk-scale mixer-settler operations. However present maximum throughputs are restrictive and there are engineering challenges that need to be overcome before the technology is robust. This is especially the case for mineral processing, where circuits must be able to handle variable feed streams with long retention times and where maintenance should be minimized. This paper highlights research directed at investigating and evaluating these challenges for actual mineral leach solutions of metal ions. Molecular and particulate channel fouling is discussed. Most extraction systems studied to date show no effects that would preclude use of the technology. For rare earth elements (REE) with fast extraction rates, scale-up of volumetric throughput to 100 L/h using suitable arrays of channels, microfluidic chips and modules is shown to be achievable using a small contactor (approx. 2 m3) platform. This requires only 2–3 % of the typical aqueous phase inventory and residence time used in an equivalent mixer-settler. For a circuit with 100 contactors, the overall residence time would be less than 1 h, using an aqueous inventory of 40 L.INTRODUCTIONHydrometallurgy is of pivotal importance in many mineral processing circuits around the world, with liquid-liquid solvent extraction (SX) a key step in the separation of many base metals (e.g. Cu and Ni), radioisotopes, precious metals, and the ‘technology’ metals, such as rare earth elements (REEs) (Ritcey & Ashbrook, 1979). The standard equipment for SX in mineral processing is the mixer-settler, in which liquid dispersions are created, by agitation, to increase the surface-to-bulk ratio and, thus increase the mass transfer rate between the liquid phases. In stream-based microfluidic SX (microSX), these high surface-to-volume ratios are achieved by contacting microscopic streams (Ciceri, Perera, & Stevens, 2014), rather than forming small droplets, so that phase disengagement can be accelerated (essentially instantaneous via branching of the two streams of liquid at a channel junction). MicroSX is profoundly different from bulk mixer-settler SX operations and offers exciting opportunities for processing hydrometallurgy solutions (Kriel, Holzner, Grant, Ash, Woollam, Ralston, & Priest, 2015; Priest, Zhou, Klink, Sedev, & Ralston, 2012). Nonetheless, the advantages of using microfluidic environments are presently balanced by very significant challenges relating to throughput, process control, coupling of stages, flow stability, and fouling. If these challenges can be met using smart chip designs, process control and clever engineering, high-value/low-volume SX processes stand to benefit greatly."

Jan 1, 2016

By Keith Jones, Largo Albert

"Decelerometer testing of a rigid guide system in a mine shaft pro vides usefuI information to operating and maintenance people. High acceleration/deceleration rates can lead to high maintenance costs to bath conveyances and shaft and can also present an operating risk . Possible disastrous results in the shaft have been avoided by restricting the maximum conveyance speed until the shaft and/ or conveyance problems have been solved.The test instrument is a valuable aid especially during commissioning or updating of a hoisting installation. High acceleration/deceleration rates also lead to reduced hoist rope life. During the past fourteen years, a total of 15,000,000 feet of testing was performed in 74 assorted shaft compartments.Based on this experience, it is possible to establish acceptable conveyance maximum speeds provided that all other conditions in the shaft compartment are normal. The body of the paper will present examples of several tests made under actual operating conditions.IntroductionMore and more mine operators are recognizing the real value in the use of the decelerometer for determining the state of shaft guide alignment in their shaft compartments , not only during the initial mine start-up periods, but also on a regular basis while the mine is in production.Decelerometer testing, is a technique in which an accelerometer , commonly known as a decelerometer, is used for measuring conveyance acceleration/deceleration in a lateral plane. lts purpose is to determine the severity of shock loads produced by misaligned shaft guides. Testing is performed by mounting the instrument on the conveyance and operating the conveyance (empty and loaded) at various speeds up to and including full speed . However, full speed may not be attained due to conditions indicated by the tests. These conditions may present an operating risk to the plant."

Jan 1, 1984

By S. A. Willis

For over 150 years gypsum from Nova Scotia has been shipped via water to the United States east coast. The history of the movement has been one of continual improvements in quarrying, loading, and shipping. At the start, man-size rock quarried by hand auger and black powder was loaded into horse-drawn carts, hauled to the waterfront, and dumped into 100-ton sailing schooners. Last year the Canadian Gypsum Company completed the latest and most modern of these successive installations for the movement of this Nova Scotia product. The new system loads crushed gypsum into 11,600-ton vessels at Hantsport in two hours' time at high tide. At the head of the bay of Fundy are located vast deposits of gypsum. The tidal rise and fall of 45 feet twice a day, with its attendant swift currents, has always presented major navigation and shipping problems. When the tide is low, the Hantsport ship-loading pier is high and dry, with no water within 400 feet. Three hours later a large river has flooded in (running up hill) and large steamers can dock at the wharf. Before high water, the ship has been loaded and -there is a depth of 30 feet or more of water around the wharf. At high water, the ship sails away on the ebbing tide as the river runs in the other direction. Tides are caused by the gravitational attraction of the moon and sun on the ocean. When both celestial bodies are pulling together the 'spring tide' results, which means a 50-foot variation from high to low. This occurs at new and full moon. A week later, when the sun and moon work in opposition, the difference is only 32 feet between high and low water. The bay of Fundy, having a funnel shape (150 miles wide at mouth from Yarmouth to Portland, while the upper estuary at Hantsport is only one mile wide), builds up a tidal influence from 10 feet at the mouth to an average of 45 feet at Hantsport.

Jan 1, 1948

By K. M. Wild, C. D. Martin, F. Amann

"Argillaceous rock formations, in particular clay shales, are notorious for creating challenges in rock engineering. Due to their generally low hydraulic conductivity and their complete saturation in their natural state at depth, the behavior of clay shales is usually characterized by a strong hydro-mechanical coupling.This paper presents typical pore pressure responses monitored in different underground rock laboratories and explores alternative ways for their interpretation. The underpinning processes and their relevance are identified based on analytical and conceptual numerical models. Pore pressure monitoring data from Opalinus clay at the Mont Terri Underground laboratory, the Boom Clay at the Mol facility and the Callovo-Oxfordian clay in the Meuse/Haute–Marne URL show a similar pore-pressure response associated with stress changes accompanying tunnel construction although the tunnels were built in different rock types, at different locations, and under different in-situ conditions.The numerical analyses in this study shows that the pore pressure response around an excavation in low permeable clay shales may have different explanations. Pore pressure drops observed in the tunnel near field can theoretically be explained by both, a pure elastic response in an isotropic or anisotropic rock mass with an anisotropic stress state, or a inelastic response and related dilatancy. However, a comparison between the numerical models and the in-situ measurements revealed that the latter is more likely. This conclusion is justified by the observation that pore pressure drops occur significantly ahead of the tunnel face which is not the case in elastic numerical simulations. Pore pressure measurements in the far field, where failure processes are unlikely to occur, can only partly be explained by a linear poroelastic models. The introduction of an anisotropic material plays a key role in reproducing the responses, conceptually."

Jan 1, 2015

By L. M. Lowe, D. B. Chambers, D. G. Feasby

"The presence of the naturally occurring radioactive elements uranium and thorium in rare earth (RE) resources can present challenges in achieving regulatory and social acceptance. The discovery and awareness of radioactivity in mineral resources radioactivity typically generates strong public intuitive responses that may be project prohibitive; a significant proportion of such resources contain radioactivity.The objectives of this paper are to demystify the presence of uranium and thorium in RE resources and to demonstrate how a RE project can be safely developed, operated and closed from a radiological perspective. Radioactivity in RE resources is principally thorium-based. Thorium is interesting and challenging from a metallurgical perspective – one of those stubborn metals commonly assessed as refractory. Thorium is difficult to mobilise into solution and easily precipitates out. Thorium is a common element in the earth’s crust – about 10 ppm on average, and natural geophysical systems conclusively demonstrate its immobility. Specific mine tailings contain elevated levels of thorium, but the contained thorium is neither a significant ecological nor a personal hazard.Waste management for a hard rock rare earth project includes the management of mineral processtailings, waste rock, and metallurgical residue. Proven strategies are available for tailings and waste rockfor all climate conditions. The management of the metallurgical residues is potentially more challenging.Example robust strategies for addressing these challenges are presented.A potential way to reduce the radioactivity of rare earth metallurgical wastes is to selectively remove uranium and thorium. Uranium oxide is readily marketable, but its concentration as a byproduct typically triggers extensive regulatory processes. Thorium is presently not marketable, but may be so in the not-too-distant future with the development of thorium-based nuclear energy. The pro’s and con’s of uranium and thorium byproduct recovery are summarized."

Jan 1, 2016

By Hulbert A. Lee

"A REVIEW OF MINERAL DISCOVERIES IN CANADA, and in particular the Canadian Shield, using the physical aspects of overburden reveals a trend in the art of exploration. At an early time of exploration (1847-1954), float and heavy clasts were used successfully to find ore deposits with little knowledge of Quaternary environments. At a later time (1955 to present) , use of Quaternary rock-units for sampling have made possible tracing indicator trains of float, heavy clasts and other ore-type clasts to the source bedrock. The basal till of retreat ice is now recognized as a1l favourable sampling environment and as such has been used to successfully discover hidden orebodies. The esker massive gravel is beginning to be recognized as a favourable environment and use of it has met with technical success. An understanding of those changes that have taken place during the transportation of the material and after its deposition is essential to proper sampling and treatment of the samples from the basal till and the esker massive gravel. Use of float and heavy clasts in search of orebodies is continuing in present-day exploration on the Shield. Lessons learned from it are being incorporated into exploration using favourable Quaternary rock-units for sampling. Hence, both subjects have a need for review and are discussed in this paper."

Jan 1, 1971