Search Documents

By N. Parnian

"Carryover of caustic soda (NaOH) in the steam path caused catastrophic failure of superheater 304H stainless steel tubes in a steam generator and led to an unexpected shutdown after just five months of continuous service of petrochemical following the start of production. The cause of the failure was studied, with a focus on the formation of sigma phase in the weld joint and effect of caustic embrittlement on stress corrosion cracking (SCC). The cracks were examined at the seam weld, heat affected zone (HAZ), and Ubend areas. Hardness was measured for the base metal, HAZ, and weld metal, and microstructures were examined using optical microscopy and scanning electron microscopy (SEM). Crack initiation is attributed to gouging on the precipitated carbide at the HAZ and also the formation of sigma phase in the weld metal, as shown by energy dispersive X-ray (EDX) analysis. In addition, cracking was propagated by caustic embrittlement because of residual stresses and hammering. Finally, the characteristic feature of fracture was illustrated by SEM fractography, and consists mostly of intergranular SCC and some quasicleavage transgranular. INTRODUCTIONThree key factors are needed for the initiation and propagation of intergranular stress corrosion cracking (IGSCC): a susceptible material, a corrosive environment, and sufficient stress. Although austenitic stainless steels are susceptible to sensitization and IGSCC, they are widely used in boiler and superheater tubes because of their high corrosion resistance, high oxidation resistance, acceptable mechanical characteristics at elevated temperatures, and low cost.Sodium hydroxide is injected to neutralize acidic constituents in the steam path, but caustic can concentrate in boiler tubes and attack the surface metal (known as gouging) even traces of caustic in the steam can deposit on surfaces and cause local concentrations of several percent (ASM handbook, 1992). Not only sensitized grains but also sigma phase formed in the weld metal can initiate caustic cracking. In this research, the cause of the failure of 304H stainless steel superheater tubes in a methanol petrochemical plant in Iran was studied with a focus on the effects of caustic embrittlement on IGSCC."

Jan 1, 2012

By Stephen van Duin

As productivity in coal extraction demands increase in underground coal mines, the industry is faced with finding new ways to support production without jeopardising safety. In modern mines the capacity and scale of longwall coal extraction has steadily increased to a point that support processes are failing to keep pace. In particular, roadway development is continually placed on the critical path of activities which maintain mine production, so any inefficiency in this area is quickly exposed. Original equipment manufacturers are under immense pressure to modify their machines to be more interconnected with each other, with machine communication and logistical sharing of space becoming a known requirement. This paper looks at the changing trends in mining practice, analysing available technology as well as currently emerging research into hard automation and discusses the need to integrate machinery and processes in order to see increases in productivity and safety.

Aug 1, 2013

By C. A. Born

This paper describes the rejuvenation of a molybdenum mine mill complex at the head of Alice Arm, 500 miles north of Vancouver and 85 miles north of Prince Rupert, British Columbia. It includes a description of the property history of the deposits and of the previous operations, together with details of the project for re-opening the mine.

Jan 1, 1979

By J. F. Davis

Pegmatite dykes containing lithium minerals and beryl occur dose to the borders of intrusive masses of granitic rock in the Winnipeg River area of Manitoba. Both vertical and flat-lying dykes are present. Most of the pegmatites consist of zones, containing characteristic mineral assemblages, arranged more or Jess parallel to the borders of the dykes. Five important lithium minerals are present; each occurs in a separate zone, but all the lithium-bearing zones are situated toward the centres of the pegmatites. Spodumene is the most abundant and widespread of the lithium minerals and occurs as small crystals intimately intergrown with quartz. Beryl is not an important constituent of the lithium pegmatites, but when .present, occurs outside the lithium zones, toward the margins of the -dykes. Beryl is most common in dykes containing few or no lithium minerals. The mineral assemblage in the beryl zone of the lithium dykes is the same as that of the beryl dykes. The attitude and internal structure, particularly zoning, of the pegmatite dykes, and the texture and assemblages of the constituent minerals, have an important bearing on exploration, development, and mining of these pegmatites, and on the extraction of various mineral products from them.

Jan 1, 1958

By Yan Jie

A series of production technologies are described for gold recovery from complex gold concentrate blended with copper concentrate treated in the SKS smelting process comprising: 1) Feed preparation and proportionate feeding of complex gold concentrate and copper concentrate; 2) SKS smelting gold recovery operation and process control technology developed based on reaction mechanism, process simulation and slag formation optimization study; 3) a dry-process quenching arsenic collection technology developed during de-bottlenecking severe restriction of SO3 in the off-gas on As collection system by suppressing and eliminating SO3 in off-gas as a result of optimizing SKS smelting process conditions and spraying caustic soda absorbent so as to reduce off-gas dew point temperature; 4) electrorefining of impure anodes; 5) technology for recovering such precious metals as Au, Ag, Pt, Pd, etc. from high-Sb copper anode slime produced as a result of gold recovery from complex gold concentrate by using SKS smelting process. INTRODUCTION Gold concentrate resources in China are mainly found in Shandong province, Henan province and the Inner Mongolia Autonomous Region, etc. Currently, recovery of gold is based on pre-oxidation (roasting) cyanide leaching process. This process produces a large amount of cyanide-containing wastewater, cyanide leaching residue and relatively high SO2-bearing flue gas during production, which can cause increasingly more serious environmental pollution issues. Besides, this process route suffers from a relatively low precious metals recovery (70–80%) found when treating refractory gold concentrate and carbon-bearing gold concentrate. These issues have severely restricted the development of the precious metals processing industry in China.

Jan 1, 2019

By J. Costigan, C. Corless

In 1997, damage as a result of Castrol R40 entering the INCO pressure carbonyl plant carrier gas stream was becoming increasingly severe. The oil in the gas stream was adversely affecting both equipment availability and process control resulting in rising unit costs. The main source of the Castrol R40 was determined to be the carrier gas and low pressure gas blowers. Plant personnel initiated a plan to prevent the Castrol R40 from entering the carrier gas stream by replacing the mechanical shaft seals with Ferrofluidics seals on these blowers. The following paper details a brief case history of the Castrol R40 in the carrier gas including impact on the plant. This will be followed by a technical discussion of the new sealing arrangement that was developed by plant personnel, Roots Blower and Ferrofluidics. Lastly, this paper will update the status of the blower upgrade project and document the results to date.

Jan 1, 2000

By N. Ginouse, S. Reny

"In the mining industry time is critical as production depends on the speed of the mining cycle. During the mining process, the time required to re-open access for the next phase of an underground heading is a key point that strongly depends on the ability of the selected ground support technique to promptly ensure the safety of workers. Fiber reinforced dry-mix shotcrete has been proven to be an efficient and well adapted technique, able to produce a ground support material with the required energy absorption or flexural toughness in a single application phase. In this context, this paper demonstrates the possibility of significantly speeding up the mining process by using a new fiber reinforced dry-mix shotcrete. The new fiber reinforced dry-mix shotcrete is capable of developing flexural toughness in only 24 hours that is equivalent to what is typically achieved after 28 days using current fiber reinforced drymix shotcrete technology.INTRODUCTIONShotcrete is often used for ground support when using the drill and blast method or other tunnelling methods. But before re-opening access for the next phase of the underground heading, the applied shotcrete is required to reach a minimum compressive strength and in case of fiber reinforced shotcrete, a minimum flexural toughness (energy absorption) in order to ensure the safety of the workers going into the heading. Combined with bolts, the use of conventional fiber reinforced shotcrete becomes an interesting method for ground support as it is applied very soon after excavation and works to stabilize ground movements (Bernard E. S., 2009). In this case, the toughness development of fiber reinforced shotcrete becomes an important feature of the material when looking to speedup the mining cycle. However, early re-entry criteria in underground openings are difficult to ascertain as the load carrying capacity of fiber reinforced shotcrete is usually assessed after 7 or 28 days. For this reason, re-entry criteria varies from one mining area to another and are usually based on compressive strength requirements. For example, in northern Ontario, Canada, one of the current practices in the mining industry consists of allowing safe re-entry once fiber reinforced shotcrete has developed a compressive strength of higher than 4 MPa (Dufour, O’Donnell, & Ballou, 2003). Flexural toughness requirements on fiber reinforced shotcrete are also typically based on evaluation after 28 days."

Jan 1, 2015

By C. Moctezuma

Since the start up of the IMMSA electrolytic zinc refinery in 1982, the dissolved iron coming from the acid attack of the ferrites has been precipitated by the jarosite process. At the beginning of operations, sodium jarosite was produced; however, the plant was converted to ammonium jarosite in 1990. The final storage of the residue is on the company&apos;s property adjacent to the plant, over the natural surface of the land. Before the construction of the refinery, several studies were done in order to evaluate the characteristics of the ground, such as, permeability, underground water localization, etc. The results showed that the site was adequate for the storage of this kind of material. For several years, the jarosite residue was filtered on rotary drum filters and was sent as a pulp to the storage area for settling. The water from the storage pond was recycled to the re-pulp tank for the jarosite residue. These filters were replaced in 1999 by an automated filter press. Since then, the jarosite residue has had a lower water content, and the zinc recovery improved. At present, a second filter press for the jarosite circuit is in the acquisition process to diminish the soluble zinc content in the residue from the present value of 2% to < 1% Zn.

Jan 1, 2006

By R. D. Parker

Location The Frood ore-body is expressed on surface as a prominent gossan ridge, with a total length of approximately two miles. The original Frood (the old No. 3 mine of the Canadian Copper Company) is at the southwest end of this gossan; adjoining it on the northeast is the Frood Extension (until 1929 the property of i:he Mond Nickel Company), while at the extreme northeast end is the Stobie mine. The first two of these divisions of the ridge form the Frood mine as it is known today.? This lies in lots 6 and 7 of the sixth concession, township of McKim, and is two and a half miles north of the city of Sudbury. The general elevation is 1,000 feet above sea level. The Ore-Body The Frood-Stobie parallel offset(l), as its name implies, has no connection in the field with the main mass of the Sudbury nickel eruptive-a norite. It lies one mile to the southeast of that body, and, in general, parallels it in strike. The ore occurs as a more or less tabular structure in what is known locally as the Sudbury series. They are the oldest rocks of the district, and have been placed by Collins(2) as earlier than the lower Huronian, of pre-Cambrian time. The series is comprised of sediments, volcanics (both acid and basic flows), tuffs, agglomerates, breccias, and basic intrusives, all highly metamorphosed, yet all forming a more or less regular picture. The controlling feature of the area has been the attitude of the sedimentary strata, from which has arisen the present sill-like character of the flow rocks, the basic intrusives, and the ore-body itself.

Jan 1, 1932

By Ali M. Ghazi, Ronald J. Goble, Lowell S. Whiteside

"Geerite (Cu1.6S) is a rhombohedral copper sulphide which occurs naturally in epitactic replacement of sphalerite; cell dimensions closely approximate those of the host sphalerite.Geerite-type structures can be produced by leaching digenite (Cu1.8S) in ferric sulphate solutions. X -ray diffract ion and electron microprobe studies indicate that eight metastable geeritetype structures can be produced, depending upon the concentration of f erric sulphate solution used and the duration of the each. Although compositions cluster on or near values observed for natural phases, optical properties indicate that we are dealing with polymorphs of these phases. Leaching of chalcocite (CU2Sj in dilute f erric sulphate solutions produces similar results. In contrast, leaching of chalcocite in more concentrated solutions seems to produce true analogues of natural minerals.During froth flotation, sphalerite is activated with a monolayer of floatable copper sulphide with the composition, CuS, of the mineral covellite. However, covellite is not significantly more floatable than sphalerite, and has an incompatible structure because of the presence of covalently-bonded atoms of sulphur. Leaching ofdigenite was used to produce a polymorph of covellite with a geerite-type structure, compatible with that of sphalerite. This polymorph has a flotational behaviour similar to copper-activated sphalerite, suggesting that the monolayer has a geerite-type CuS structure. IntroductionIn an ideal close-packed sulphide structure the distance between sulphur layers, D, is equal to 2R 2/3, where R is the radius of the sulphur atoms. In sulphides with covalently-bonded sulphur layers, such as covellite (Fig. I), D will be an average of the number of covalentl y-bonded and close-packed sulphur layers, weighted as to the relative number of each type of layer. Both D and R are spacings which are readily identifiable structurally and on X-ray diffraction patterns. Goblel has shown that for copper-iron sulphides with metal-to-sulphur ratios between 0 and 2 and copper-to-total metal ratio s between 113 and I there are strong correlations between composition and measured D and R distances (Fig. 2). D can be represented by a single empirical equation relating interlayer spacing to composition; R must be represented by three equations relating the radius of sulphur atoms to composition. One of these equations (R, in Fig. 2) represents ideal close-packed behaviour, the other two represent sulphur radii greater than (R1) or less than (Rh) the ideal."

Jan 1, 1988

By G. Stafford Whitby

N ATURAL gas is found in several provinces of Canada, particularly Ontario, New Brunswick, and Alberta. The largest producer is Alberta, and there the most important field is the Turner Valley, where some low-gravity crude oil and naphtha are associated with the gas. Last year there was produced from the Turner Valley field an average of 3,462 barrels, or about 450 tons, of oil a day. The gas flow from the wells in this field bears such a high ratio to the oil which comes from them that, despite the enforcement of a measure of conservation, it amounted to the vast quantity of 6,000 tons a day, or more than 2,000,000 tons a year. Prior to the application of any conservation measures, the gas flow was at one time of the order of 12,000 tons a day. The heat content of one ton of the gas is almost equal to that of two tons of coal. A certain amount, say, 10 per cent," of the gas is used in Calgary and surrounding towns and in re-pressuring the Bow Island gas field, but the greater part of it goes to waste. What are the possibilities of making use of this waste gas, in whole or part? The possibilities of using it profitably as fuel for domestic and industrial purposes have undoubtedly been carefully considered by the Company which now distributes a part of the gas to cities and towns in Alberta. But the relative sparness of the population and the cost of pipe lines makes such possibilities strictly limited. There are, however, distinct possibilities of making use of at !east a part of the gas for the production of a variety of chemical products and of liquid motor fuel. The present paper is devoted to outlining some of these possibilities. About three-quarters (by weight) of the Turner Valley waste gas consists of methane, the lightest and, chemically speaking, the simplest of hydrocarbon gases. The remaining quarter consists of heavier hydrocarbon gases-ethane, propane, and butane. Formerly, naphtha was separated from the well gas by a simple process of self-refrigeration. The gas coming from the wells at a pressure of, say, 1,200 to 1,800 lb., was passed through simple cylindrical vessels fitted with baffles and known as &apos;separators&apos;. The pressure was allowed to drop to, say, 300 lb. in the separators, and the cooling effect secured by this expansion brought about separation of the naphtha. The naphtha thus obtained was &apos;wild&apos;, that is, it had a high vapour pressure owing to the presence in it of dissolved and liquefied gas. In order to reduce the vapour pressure to a level at which the naphtha could be shipped, this gas was removed either by distilling it out through a &apos;stabilizing&apos; column or, according to the practice at many wells, merely by allowing the naphtha to &apos;weather&apos; in open tanks (heated by coils if necessary) until the gas had been driven off in to the air.

Jan 1, 1936

By T. Holmes, S. Davison

"The Special Standard Surge bin at Agrium’s Vanscoy Potash Operations (VPO) has been plagued with flow problems and wear, and corrosion issues for it’s entire working life. Investigation showed that the carbon steel construction, bin geometry, and resultant funnel-flow pattern were directly responsible for production losses and disproportionate maintenance and capital costs. Potash enters this bin at between 140°C and 165°C, but the stagnant potash outside the active flow channel was much cooler, allowing moisture to migrate toward the outer regions, which caused corrosion of the walls and reduced live capacity as the potash in this area hardened and built up on the walls over time.A 2013 inspection revealed holes and paper-thin areas in the lower cylinder wall sections and in the conical hopper. The only thing preventing major leaks and even a potentially catastrophic failure was the buildup of stagnant hardened product on the cone walls. It was concluded that the cone had reached the end of its life and required replacement. VPO’s original plan was to replace the cone in kind and repair the cylinder as necessary; however, a failure-mode and bin-performance investigation combined with a lifecycle- cost analysis indicated it would be better to redesign the hopper.For success in retrofit projects, it is essential at the design stage to consider the bulk solid flow properties and the operating environment involved. Because education in this area is not offered at a university level, engineers often do not fully appreciate the effects of the flow properties of bulk solids on bulk material handling equipment.Jenike & Johanson conducted flow properties tests on samples of potash and using the data, redesigned the bin and the feeder. After the modifications, VPO’s surge bin provides safer, more reliable operation with a much longer predicted working life. Using this retrofit as an example, we aim to provide a general understanding of bulk solids flow theory and highlight the importance of customizing the design to the appropriate flow properties in the cost effectiveness, reliability, and safety of a bulk material handling system."

Jan 1, 2016

By N. Ahern, D. B. Dreisinger, G. Van Weert

In the thiosulfate leaching of gold, degradation of the thiosulfate reagent is a major cost. One of the intermediary degradation products is trithionate, which also inhibits gold recovery from solution by ion exchange. Little attention has been given to this species in the context of gold leaching - the limited information on trithionate and its solution chemistry available in the literature is seldom directly related to gold leaching conditions. This review is a compilation of the published knowledge on trithionate, with a specific focus on identifying the relevance of this information to gold leaching and the shortcomings in the knowledge base.

Jan 1, 2005

By Jacque Turgeon, Gontran Foy

"The Mineral Research Centre of the Quebec Department of Energy and Resources has worked extensively on the development of a dry process to extract pure mica flakes from a phlogopite ore. The liberation of mica from the gangue is effected basically by impact crushing, and the ground ore is screened into several fractions, each having a fairly narrow range of grain size. Each sized fraction is then fed to an air separator where heavy grains are separated from light flaky grains. Heavy fractions are returned to hammer mills where gangue minerals are ground finer and blocky mica particles are exfoliated. A second stage of screening is performed and each fraction is sent to an air separator. This sequence is repeated until mica products are virtually free of gangue. These different fractions are then treated in a cage mill in which mica flakes undergo a more orderly exfoliation along cleavage planes. The ground mica is again submitted to a final screening stage, after which each fraction constitutes a final commercial product.This process permits the recovery of about 70% of the mica contained in the ore. The over-all process will be described along with technical details of each unit operation. Recent work on a wet grinding method to produce very fine mica will also be discussed.IntroductionRecords of production of mica in Quebec date back to 1886. Production has been more or less continuous since that time, with peak activity during the war years. Production was interrupted in 1966, but started again in 1972 when Marietta Resources and Laviolette Mining and Metallurgical Corporation started their joint operation in Canton Suzor, northwestern Quebec. Mica deposits of more or less importance exist in different parts of Quebec, of which three have attracted attention in recent years: the Canton Suzor deposit, the Canton Lamy deposit and the Canton Chasseur deposit. The Suzor orebody was first identified by Carl Faesler in 1936, who described the rock as ""brown biotite in flakes half an inch in diameter, with interstitial augite, apatite and feldspar""."

Jan 1, 1982

By F. L. Wu

Based on the analysis of a sealed coal mine resulting from a fire-triggered explosion, limitations were discovered in the re-entry procedures used to reduce the size of the sealed area that were being applied during the process of re-opening the mine. The analysis of two re-opening plans in a mine using mechanical ventilation showed that the estimation of the degree of damage of two air doors close to the working face with the fire was key to the identification of the optimum mine recovery plan. The operation points of airflow and air pressure of the main fan under either the doors? damaged or intact conditions can be estimated through the use of a ventilation network simulation program. Starting the main fan for a short time period and measuring its operation points of airflow and air pressure allowed their comparison with the simulated values. This procedure provided a reasonable estimation of the degree of damage of the ventilation structures and more confidence in choosing a recovery plan. Through this process, it was possible to conclude that the two doors were still intact. Consequently, the final plan of installing a new main fan in the main decline, sealing the initial upcast shaft and unsealing the auxiliary downcast shaft, was proven to be reasonable at the mine site.

Aug 1, 2013

By P. Dinham, G. C. Summerton, N. McCulloch, S. Dowling, D. C. Craig

"Development of a process for the treatment of a nickel copper matte rich in the minerals heazlewoodite, chalcocite and bornite has demonstrated significant base metal recoveries and metal separation efficiencies. The determination of chemical and mineralogical changes occurring in the individual leaching stages in laboratory experiments has enabled a better understanding of the complex leaching chemistry. The chemistry and mineralogy of the piloting and laboratory processes are discussed.INTRODUCTIONThe nickel-copper sulfide ores of the South African Bushveld Complex are among the most important Platinum Group Metal (PGM) bearing ores, and contain the world’s largest reserves of platinum. The treatment used in the recovery of PGMs from these ores includes three types of processes, namely ore concentration using physical techniques such as flotation and gravity separation, concentration by pyrometallurgical means, hydrometallurgical extraction of the base metals followed by the PGMs. Following milling of the ore, flotation involves the separation of high value minerals from gangue by taking advantage of the differences in their hydrophobicity. These differences are generally maximized through the use of a surfactant or wetting agent. Concentrates are then thermally treated and melted which brings about physical and chemical changes that enable the recovery of base metals and PGMs. The main aim of the smelting and converting process is to separate and eliminate the valuable metals from the bulk of the unwanted gangue and essentially all of the iron and to concentrate the metal VALUES (into a high grade converter matte. The matte can be further enriched by magnetic separation, producing a PGM-rich magnetic fraction and a base metal-rich non-magnetic fraction. The magnetic fraction is treated by hydrometallurgical processes to produce a PGM concentrate which is further refined to separate and purify the individual metals. The non-magnetic fraction is treated to produce marketable metal VALUES (such as nickel, copper, cobalt and to a lesser extent PGMs. The principal objective of any hydrometallurgical extractive process is to leach the desired elements selectively into an aqueous phase so as to separate them from the bulk of the material. (Crundwell, Moats, Ramachandran, Robinson and Davenport, 2011; Hundermark, Mncwango, de Villiers and Nelson, 2011)."

Jan 1, 2012

By Dougla McDonald, Richard Poulin

"Most mine managers in Canada today will agree that one of the keys to mining efficiency and productivity is their human resources. A5 a result, many mines develop some sort of incentive designed to tap their employees&apos; capabilities to the fullest extent. Historically, the most common plans used have been ""piece-rate"" plans, where individual or small groups of miners are paid a financial bonus based on some measure of their productivity. Recently, however, incentive plans that take a more team-based approach have been developed in some Canadian mines. One such plan will be defined in this paper, and its popularity in the industry today discussed.Gainsharing PlansThere are two primary components to a gainsharing plan. The first is a cash incentive, which is paid to all employees and based on factors that are highly correlated with employee productivity, and key to the profitability of the mine. For example, the typical gainsharing cash incentive is based on the cost/unit of metal produced. Management (in consultation with employees in some cases) will establish the budgeted cost per tonne, and any savings in this amount is shared between the company and the employees. The second is a management philosophy and associated communication network, which is designed to foster an environment that encourages information exchanges, communication, participation, and trust between employees and management. The typical gainsharing communication network consists of two tiers of committees. The first, operational committees, include all employees working in the same department or departments which frequently interact. The employees meet monthly with management personnel to discuss problems encountered and brainstorm for solutions. In most cases, these committees will nominate a person in the group to structure the meeting to maximize its efficiency. The second, the screening committee, is a single group consisting of representatives from the various operational groups, whose primary job is to ensure that the plan is effective, and the objectives and results generated by the plan remain consistent with the mine objectives. In short, gainsharing plans tell employees that their bonus depends upon performance and then gives them the opportunity and incentive to affect that performance. The opportunity is provided by a communication network and positive management practices, and the incentive comes in the form of ""intrinsic"" rewards of participation and the ""extrinsic"" rewards of the bonus payments. Figure I will clarify the relationship between the intrinsic and extrinsic rewards."

Jan 1, 1995

By M. Rylatt, E. Legault-Seguin, C. Mohns

"With energy costs increasing and ore grades diminishing, the role of preconcentration in hard-rock mining operations has gained greater interest. Dense medium separation is a process that can be conducted at particle sizes from 250 to 0.50 mm with high separation efficiency, depending on liberation characteristics of the valuable minerals. Pilot-plant case studies conducted at the SGS Lakefield site are presented, including mineral systems such as spodumene, sulfide-bearing gold ores, and complex sulfide ores. These case studies demonstrate that, for amenable ores, mass rejection of 20–60% is possible while maintaining recoveries of greater than 90%.RÉSUMÉ Au vu de la hausse des coûts liés à l’énergie et du déclin de la teneur des minerais, le rôle de la préconcentration dans les exploitations minières en roche dure présente un intérêt croissant. La séparation (ou concentration) en milieu dense est un processus pouvant être mené sur des calibres de grains de 250 à 0.50 mm avec un rendement élevé de séparation, en fonction des caractéristiques de libération des constituants des minéraux métallifères. Sont présentées dans cet article des études de cas menées dans des usines pilotes du site de Lakefield de SGS, lesquelles incluent des systèmes de minéraux tels que le spodumène, les minerais aurifères sulfurés et les minerais sulfurés complexes. Ces études de cas montrent que pour les minerais présentant les caractéristiques de libération appropriées, il est possible d’atteindre un rejet en masse de 20 à 60 %, tout en maintenant des récupérations supérieures à 90 %.INTRODUCTIONPreconcentration is the process of rejecting gangue minerals while ensuring recovery of valuable minerals prior to more intensive, downstream processing. Preconcentration has been practiced in the industry for many years, and is gaining greater interest as the industry copes with processing lower grade, more difficult ores, which typically require finer grind sizes and incur higher energy costs.The benefits of preconcentration are:• lower mining costs, which allows for nonselective mining;• lower process capital and operating costs (e.g., resulting from reduced grinding, flotation, and fines disposal stages);• increased ore reserves, which provides the potential to treat lower grade ore;• increased mine production without expansion of the existing plant or concentrator;• reduced overall tailings impoundment by converting the reject into a byproduct (e.g., underground backfill or aggregate);• improved efficiency of downstream processes (e.g., silica removal in electric arc furnace feed, removal of softer sliming minerals prior to grinding);• potential application to brownfield operations and greenfield projects; and• a “green” process option, which reduces processing energy consumption;– reduces mill feed;– increases stage metal recovery (higher grade feed);– increases mill metal output per tonne processed;– reduces surface plant, tailings dump, and tailings pond requirements because the plant has a small footprint and can be installed underground; and– can be applied to retreatment of old tailings dumps to recover metal values and reduce environmental impacts (e.g., dissolved metal runoff, acid drainage)."

Jan 1, 2017

By G. Hamel

The LCL&L process (Low Caustic Leaching & Liming) is a patented hydrometallurgical route developed by Rio Tinto Alcan (RTA) to economically process spent pot lining (SPL) generated by aluminum cells. The three resulting end-products (carbonaceous, fluorinated and caustic liquor) are inert and have valorization possibilities. An industrial size pilot plant located in Saguenay (Quebec) was inaugurated in mid-2008 to demonstrate and optimize the technology. This paper describes characteristics of the LCL&L process and the experience acquired by RTA since the plant&apos;s start-up, including ramp-up capacity and technology challenges that were overcome. Possible end-products valorization methods are also presented. The carbonaceous end-product can be separated into carbon and brick rich fractions and used as either alternative fuel, reducing agents, or as raw material for third party processes. The development of a conversion process for the fluorinated end-product would allow its reuse as a substitute to fluorspar mineral for aluminum fluoride production. Finally concentrated caustic liquor is already valorized at the nearby RTA Vaudreuil alumina refinery.

Jan 1, 2011

By A. A. Iranzadeh

The performance of a tunnel boring machine (TBM) depends on the efficiency of the cutters, which can be influenced by geological conditions and rock mass properties. In this study, a three-dimensional numerical model, based on a discrete element method, was used to evaluate the effects of joint orientation and its spacing on the fragmentation process by a TBM cutter. Several models were constructed to study the effects of variable orientation; these models incorporated different spacing, variable spacing, different orientations on the fragmentation process, and different sections of the block model. Three parameters, consisting of induced tensile stress, induced shear stress and maximum displacement, were calculated. The stress in each section that forms chips was considered as critical stress; critical joint spacing and orientation in each section were determined. Results show that the critical orientation was in the range of 45 to 60º, where there was a possibility to achieve the maximum penetration rate. The critical joint spacing was 200 mm and, by increasing joint spacing, the value of critical stress decreased significantly. Furthermore, joint orientation could influence more than joint spacing in the rock cutting process.

Jan 1, 2009