Search Documents

By W. G. Hubler

It has been within only the last two or three years that enough progress has been made in preferential flotation to warrant metallurgists in recommending the installation of commercial-sized plants for the treatment of copper-zinc-iron ores. Until the new processes had been worked out successfully, the treatment of this type of ore had proved a stumbling block in the path of metallurgical progress. Separation of lead-zinc ore is comparatively simple. A lead-zinc ore low in iron may be separated and concentrated by gravity con-centration, provided it is not necessary to grind too fine. Owing to the specific gravity of chalcopyrite and sphalerite being so nearly the same, however, their separation by gravity concentration is out of the question. Complex lead-zinc-iron ores in which the several minerals are intimately associated, requiring fine grinding to free them, have been successfully treated by flotation for the past fifteen years. Galena is easily floated, and its flotation, unlike that of chal¬copyrite, is not affected by the reagents used to inhibit the flotation of sphalerite and iron sulphides. When an attempt was made to use the methods of lead-zinc se-paration on copper-zinc ores, it was found that the depressant re-agents added to inhibit the flotation of the iron and zinc minerals would, under certain conditions, depress a large part of the copper. It was also recognized that, in the grinding of copper-zinc ore, soluble salts were generated which were detrimental to flotation unless properly controlled. The main part of this paper will be a discussion of solutions in the grinding circuit in relation to the pro¬duction of soluble salts and their effect on flotation.

Jan 1, 1931

By Barry D. Simmons

"A well-defined approach is essential to ensure the long-term success of a regional exploration program. Teck's approach in eastern Canada is designed to fulfill corporate objectives while recognizing certain unique parameters for exploration in the area. The elements of this approach include clearly defined objectives, technical considerations and personnel policies, all of which are equally important. The goal is a significant discovery before the mid-l990s and the company is confident that this target will be achieved.IntroductionAs one of Canada's oldest continuously operating mining companies, Teck Corporation traces its roots to Kirkland Lake, Ontario, with the development of the Teck-Hughes gold mine in 1913, later supplemented by production from the Lamaque gold mine in Val d'Or, Quebec. Control of the company was acquired by Temagami Mining Company, part of the Keevil Mining Group, in 1959. Credited as one of the first discoveries made using airborne geophysics, the Keevil Group had recently found the small but very high-grade copper deposits at Temagami, Ontario. These developments in eastern Canada formed a foundation for remarkable growth and Teck's present status as one of Canada's most successful and respected mining companies.Teck currently operates successful mining ventures across Canada and has international exposure through its association with Cominco Ltd., M.I.M. Holdings Limited and Metallgesellschaft AG. Operations in eastern Canada, however, remain an important component of Teck's ongoing success. The David Bell and Williams mines at Hernlo, Ontario, are Canada's lowest cost and largest gold operations, respectively. The Niobec Mine at Chicoutimi, Quebec, is North America's only significant producer of niobium. Teck maintains a 45070 interest in Golden Knight Resources Inc., part owner of the successful gold mining operation in the Casa Berardi area of northwestern Quebec. As a significant shareholder in Aur Resources Inc. and as a part owner, Teck is participating in the development of the Louvicourt deposit, a major base metal discovery at Val d'Or, Quebec."

Jan 1, 1992

By X. Q. Jiang, D. L. Chen, A. Macwan

Magnesium alloy, being the lightest structural material, is a key candidate for the weight reduction of vehicles in automotive and aerospace industries; however, its poor corrosion resistance and difficulty in deformation are limiting factors. Recently, Al/Mg/Al tri-layered clad sheets have been considered as a promising alternative to improve corrosion resistance and formability of magnesium alloys. The aim of this study was to evaluate the tensile properties and deformation behavior of Al/Mg/Al tri-layer clad sheets at different temperatures and strain rates. Yield strength (YS), ultimate tensile strength (UTS), and elongation were observed to increase with increasing strain rate. With increasing temperature from -40°C to 180°C, YS and UTS decreased and ductility increased. The strain hardening exponent evaluated via three equations of Hollomon, Swift, and Afrin et al. showed a similar increase with increasing strain rate and decreasing temperature. The fractographic analysis showed partial debonding of clad interface especially at higher strain rates and lower temperatures.

Jan 1, 2015

By G. F. MacDonnell

THE Privateer mine consists of a group of mineral claims situated in the Zeballos area, on the west coast of Vancouver island, approximately 180 miles north of Victoria. Although Zeballos is a comparatively new mining camp, its transportation facilities can be considered exceptionally good. General freight and supplies are brought in by either C.P.R. or Frank Waterhouse steamers from either Victoria or Vancouver. Service by these boats varies from five to ten days and the trip from Victoria takes approximately two days. Passengers may use the C.P.R. boats, or, if speed is essential, they may fly, in which case they have the choice of two flying companies, namely, Canadian Air-ways, Limited, and Ginger Coote Airways. The average flight from Vancouver takes approximately two hours. Excellent unloading facilities are provided at the beach by a government dock for the steamers and a floating dock for aeroplanes. The mine, which is approximately five miles from the beach, is serviced by a fairly good gravel road, which has proved satisfactory for all haulage purposes. Zeballos has the reputation of having one of the heaviest rainfalls on the west coast, but as no accurate records have been kept, no comparisons can be made. H. C. Gunning, in his report, comments on the weather from 1929 to 1932, and one would judge that the practically continuous rainfall did not add to the pleasures of the field work. During the summer of 1938, the opposite condition prevailed and the area had exceptionally dry and pleasant weather. The snowfall is generally light at the lower elevations, but very heavy higher up. No extreme cold weather is encountered during the winter, which is generally short.

Jan 1, 1939

By A. J. Stapleton

"This paper gives a brief description of the occurrence and development of the Needle Mountain mine at Gaspe Copper Mines, Limited and describes the trackless mining equipment used in this highly mechanized underground operation.Maintenance of the trackless equipment is considered in detail, with particular emphasis on scheduling and control, examination and inspection. All maintenance is carried out in an underground garage, and the facilities for maintenance and field repairs are also described. Maintenance costs are given for various units and the figures for different types of loading and haulage units are compared to support the trend toward larger units and the increasing use of rubber-tired loaders."

Jan 1, 1969

By Songgen He, Jianchun Guo

With the development of complex, unconventional and deep reservoirs, it shows that many rocks behave plastically with the influence of clay and confining pressure. Traditional linear elastic hydraulic fracturing initiation models are not good predictors for elastic-plastic reservoirs. With the deformation theory of plasticity, a power hardening constitutive equation was developed in piecewise approximation method. Based on the nonlinear constitutive equation, a model of the stress field around the wellbore was developed considering fracturing fluid penetrating effect and in-situ stress anisotropy. At last, coupled with the maximum tensile strength criterion and Mohr-Coulomb criterion, a new elastic-plastic hydraulic fracturing initiation model was built. The following conclusions were summarized in the paper: (1)The piecewise power hardening constitutive equation based on the deformation theory of plasticity can accurately describe the nonlinearity of elastic-plastic deformation. (2)Whether the rock is yielded or not is determined by in-situ stress, yield stress, Biot coefficient and pore pressure. (3)Plastic yield has little influence on radial stress but significant impact on circumferential stress. The radius of the plastic zone is positively correlated with in-situ stress but negatively correlated with yield stress, power hardening index, pore pressure and Biot coefficient. (4)Initiation modes include tensile failure and shear failure when rock is yielded. (5) For elastic-plastic reservoir, the initiation pressure predicted by linear elastic model is much lower if the rock is yielded.

Jan 1, 2015

By M. H. Leite, R. Corthésy, D. E. Gill

"La connaissance des contraintes naturelles qui prévalent dans les massifs rocheux est un prérequis indispensable pour la conception sécuritaire et économique des excavations comme on en retrouve dans les exploitations minières souterraines. Certains chercheurs se sont attardés à colliger les résultats de mesures de ces contraintes et les ont utilisés pour produire des modèles de prédiction basés sur leur traitement statistique. Ces modèles de prédiction sont très populaires auprès des exploitants miniers puisqu’ils permettent, du moins dans les étapes préliminaires de design, d’obtenir de façon s’apéconomique mais approximative, une partie des paramètres dont ils ont besoin. Dans le cadre d’un projet initié en 1994 avec la collaboration de l’IRSST, il a été décidé de produire un modèle de prédiction englobant une partie de la zone périphérique de la faille de Cadillac, soit une zone plus restreinte que le Bouclier Canadien utilisé jusqu’ici comme région pour l’élaboration de tels modèles. Pour produire ce modèle de nouvelles données obtenues avec une technique permettant d’exercer un excellent contrôle de qualité ont été ajoutées à celles déjà disponibles. Une telle régionalisation des données de base permet d’obtenir un modèle où les intensités et les orientations des contraintes principales sont beaucoup moins dispersées que ce que rapportent les modèles publiés jusqu’à ce jour. Enfin, il est démontré que le modèle proposé pour la région étudiée est en toute probabilité plus sécuritaire que les modèles plus généraux publiés à ce jour. Knowledge of the in situ state of stress existing in a rock mass is essential to the safe and economical design of underground mining excavations. Prediction models have been published, based on the statistical treatment of stress measurement results. Such prediction models are very popular among mine operators because they allow them, at least at a preliminary design stage, to economically obtain part of the information needed, even if this information is approximative. In 1994, a research project financed by IRSST was initiated aiming to produce a prediction model that would comprise a peripheral zone around the Cadillac fault. This region is more confined than the Canadian Shield on which the existing prediction models have been based up to now. In order to produce such a model, existing stress measurement results have been used in conjunction with new stress measurements that have been performed based on a technique which allows full control of the quality of the measurements. Restricting the data upon which the model is based to a more specific region gives a model in which the intensities and the orientations of principal stresses are far less scattered than the results published to date. Finally, it is shown that the proposed model is probably safer for the studied region than the models previously published."

Jan 1, 1998

By G. M. Ritcey

The recovery of copper from low-grade solutions res ulting from dump leaching is well known, whereas the recovery from highly concentrated copper solutions has not been practiced. This paper discusses the use of Ashland Chemical's Kelex 100, a substituted quinoline, for the recovery of copper from solutions resulting from leaching copper-nickel concentrates. A flow sheet is described, and an economic comparison shows Kelex 100 to be superior to either the LIX 64N or LIX 70 reagents of General Mills for the recovery of copper.

Jan 1, 1973

By M. K. Gangal, M. A. Stoakes, A. E. Hall

"The major features of the CANMET thermodynamic mine ventilation network program, developed by the Mining and Mineral Process Engineering Department of the University of British Columbia for the Canada Centre for Mineral and Energy Technology (CANMET), are described.The program is designed for use by deep Canadian mines in planning ventilation flows where the effects of auto-compression of air, moisture lift work and natural ventilation are significant. Routines to simulate stalled fans and give an optional cost printout have been included in the program.A supplementary plotting program used to simplify data interpretation is also described.The program is described with a test data example of a deep mine. It is a valuable analytical tool which can assist ventilation engineers to simulate many alternative ventilation strategies at a low cost in a very short time.IntroductionCanadian underground mines are becoming deeper and more extensive. The use of more and larger diesel-powered equipment increases the amount of air required to be circulated in these complex systems. These effects, coupled with the increasing unit cost of the energy required for mine ventilation, require that the air is used with maximum efficiency.Optimum airflow distribution can be obtained by using network computer programs enabling engineers to plan future ventilation systems based on quantitative assessments. The programs used for deep mines must make allowance for the change of air density with depth, as the assumption of incompressible flow leads to serious errors. Natural ventilation effects may vary with depth and from part to part of the mine; this must be catered for by the program. The air moisture content changes throughout the circuit and a significant portion of the fan work may be used in removing moisture from the mine; as this work varies directly with the flow, a suitable relationship must be utilized in the program."

Jan 1, 1982

By B. C. Jago, H. Derbuch

"The Freightrain kimberlite is located on the Brodeur Peninsula, Baffin Island, Nunavut. Twin Mining is exploring the pipe and adjacent land (79 claims/655 km2) using a combination of airborne geophysics, soil sampling, diamond drilling, trenching and bulk sample processing. The pipe originally was discovered by Cominco Limited in 1975, re-evaluated in 1993 by Lumina Investment Corporation, when it was staked as the Zulu pipe, and subsequently covered by three claims in 1998 by Helix Resources who called it Freightrain.The Freightrain pipe coincides with a strong, ovoid-shaped aeromagnetic anomaly. It is the only surface exposure of kimberlite within a 30 km long linear trend of fourteen aeromagnetic anomalies that are up to 600 m in diameter.The pipe is exposed in the crater facies, near the transition into diatreme facies as indicated by the occurrence of pyroclastic kimberlite characterized by abundant olivine macrocrysts, juvenile lapilli and kimberlite autoliths set in a serpentine-calcite matrix. Olivine, Cr-pyrope garnet and chromite are the most abundant macrocrysts; clinopyroxene, ilmenite and phlogopite mica occur in minor to trace amounts. Garnet and chromite harzburgite, garnet lherzolite, garnet-spinel lherzolite and rare eclogite dominate the xenolith population.Garnet and chromite mineral chemistry indicate encouraging diamond prospectivity and that potentially diamondiferous garnet and chromite harzburgite were the principal sources of diamond in the mantle at the time of kimberlite eruption.Single clinopyroxene grains define an ~42 mW/m2 sub-continental geotherm that is rooted in the diamond stability field. This compares to a slightly hotter geotherm (~48 mW/m2) for adjacent Somerset Island kimberlites with an origin in the graphite stability field. This data accords with the general lack of sub-calcic Cr-pyrope garnet, diamond inclusion chromite and diamond in Somerset Island kimberlites."

Jan 1, 2002

By S. Hopkins, J. Nolan, S. Gillis

"Cast in place concrete shaft linings have been used in many salt and potash shafts sunk in North America over the last 100 years. A large number of these shafts have exceeded their initial design lives and as producers look to extend the life of their operational assets, maintenance costs and shaft downtime will, in many cases, continue to rise unless repair work is undertaken. Successfully implementing concrete liner repair schemes in operating salt and potash shafts is complicated due to their age, environment and time constraints during inspection, detailed design and construction. This paper outlines a general approach to the repair of concrete-lined portions of these shafts, based on lessons learned from the authors’ involvement in a recent repair project. INTRODUCTION Prior to the recent boom in potash mine construction many of North America’s potash mine shafts were entering their sixth continuous decade of production (Table 1). Of North America’s salt mines, one has been in continuous production, for nearly nine decades.As would be expected, considering the environment in which these liners operate and the age of the material, the concrete-lined sections of the shafts outlined in Table 1 have been noted by the authors to have lost both cross-sectional thickness and strength over time. Since construction, three principal factors have contributed to this loss in section/strength; (1) physical degradation (impact, freeze/thaw or rebar expansion), (2) chemical degradation from brine/water inflows (Neville 1969; Bothwell, 1972) and (3) overstressing of the liner. These factors may act in combination, in which case they can produce more significant distress than individually. Physical degradation There are three main causes of physical degradation of concrete shaft liners. The first is impact from falling debris/tools or equipment (whether large or small), which may damage specific sections of concrete lining as they fall through the shaft. Impacts tend to damage infrastructure fixed to the shaft liner more than the liner itself, so damage from this mode of failure is usually localised, for example, where bolts fixing a shaft services bracket to the wall have been pulled away, pulling out the concrete around the bolts with them."

Jan 1, 2019

By G. S. Hume

Research thrives on ideas, and the theoretical considerations of today are either the discarded notions or the proven facts of tomorrow. The progress made in the past fifty years in the acquisition of knowledge of petroleum geology is no less astounding than is the tremendous increase in the production of oil on the North American continent from 61 million barrels in 1897 to 1,917 million barrels in 1947, an increase of 3,300 per cent, with production of natural gas expanding from less than 400,000 Mcf in 1897 to approximately 4,500,000,000 Mcf, or an increase of 11,000 fold in the same period. In the search for and discovery of the oil and gas fields that have yielded such prolific wealth, no idea has had a more profound effect than has the ?anticlinal? theory of oil accumulation, propounded in 1844 by Sir William Logan, the founder of the Geological Survey of Canada, after noting the position of oil seepages on the crests of anticlines in Gaspe peninsula. Sir William apparently was not much impressed with his own idea at this time, but after the Drake well discovery in 1859 and the publication by Henry D. Rogers, of Glasgow University, formerly of the Pennsylvania Geological Survey, of a paper in which he pointed out that the seepages in Pennsylvania were on anticlines, T. Sterry Hunt, an associate of Sir William Logan on the Geological Survey of Canada, published a reasonably comprehensive statement of the anticlina theory in the Montreal Gazette on March 1st, 1861. Hunt recognized the fact that the oil ?being lighter than the water which everywhere penetrates the rocks below the water level, naturally rises and accumulates along the crown of these anticlines". This was a recognition of the fact that gas, oil, and water in an anticlinal structure separate according to buoyancy or specific gravity. For some years the anticlinal theory does not seem to have attracted much attention, but when I. C. White in 1883 revived it and put it to practical use by prospecting for 'anticlinal' oil an gas structures in Pennsylvania, West Virginia, and Kentucky, its real value not as a theory but as a fact became widely recognized. Even today, the search for anticlines as oil and gas structures is being vigorously continued. In the past fifty years, however, it has become widely recognized that petroleum and natural gas collect in many different types of structures, and these have become known by the general name of 'traps'. About 1890, terrace structures were highly regarded because it was thought certain oil fields in Pennsylvania, New York, and Ohio were directly related to them. However, as Wilson (2, p. 437) has pointed out, it is recognized to day that ?'wherever the surface evidence is complete and dependable, other factors (than the terrace structure) are found to be in control'.

Jan 1, 1948

By J. N. Brooke

"This paper deals with the training of the mining and mineral engineer and the role that these professional people must play in their company environment, particularly in relation to management.THERE IS SOME CONCERN in the mining industry that the numbers of engineering graduates attracted to it and the academic training that these people have received is inappropriate. Evidence for this is:1. -The meetings and studies initiated by the various mining engineering societies to discuss:(a) attracting students and graduates to the industry; and (b) the appropriateness of the present academic training for the needs of the industry."

Jan 1, 1968

AT the Annual General Meeting held in Winnipeg last March, the whole of one of the technical sessions was devoted to a special Symposium on Geological Investigations in Canada, introduced by a paper entitled The Geological Survey (lî which had been specially prepared by Dr. G. A. Young, Chief Geologist of the Survey, and had been published in the February BULLETIN, prior to the meeting. Geologists from each of the provinces contributed to the Symposium, including directing officials of the geological divisions of provincial Departments of Mines, representative geologists from the Universities, and company and consulting geologists. Space, unfortunately, does not permit publication of a complete record of the proceedings,_ or even inclusion of all contributions to the discussion. The following summary, however, gives what is believed to be a fair cross-section of the opinions expressed by representatives from each Province. The Symposium resolved itself largely into a discussion as to how the Geological Survey and the several provincial bureaus or divisions of geology could co-operate most effectively in the important task of carrying out geo-logical investigations, with avoidance of duplication of work and waste of effort, and, so far as broad principles are concerned, there was remarkably close agreement among those participating in the Symposium as to how the various types of investigation should be allocated as between the Federal and Provincial organizations. Briefly, the concensus was that the Geological Survey can render the most effective assistance by conducting reconnaissance investigations, with mapping at 4 miles to one inch, leaving to the provincial organizations the more detailed, and hence more local, studies and mapping at larger scales. There was general agreement that the preparation of base maps, essential to systematic geological investigation, is a service devolving upon the Federal Government.

Jan 1, 1940

By S. Foged

Umicore and MWH jointly demonstrated that mechanical dewatering of goethite and neutralised tailings significantly increased the life of a 30 ha tailings pond and improved the operation of the pond. Umicore operates one of its zinc production plants in Balen, Belgium. As part of its production process, an excess of neutralised and goethite¬containing tailings is generated. These have historically been stored inside large lined ponds. As the storage area of the current goethite pond was nearing its capacity, Umicore studied the potential for an extension to the existing embankment. However, this extension would face intense regulatory scrutiny, because the environmental and safety impacts were considered important. Together with Umicore, MWH suggested and investigated an alternative treatment approach consisting of mechanical dewatering prior to storage. A feasibility study was prepared where wet storage was compared to dry storage. Differences in safety risks, environmental impacts and economic costs were outlined. The study demonstrated that the life of the tailings pond could be increased from 6 to 22 years, seriously reducing the environmental impacts and safety risks at no significantly higher cost than would have been incurred with the continued operation of the existing pond. The results of the study are presented in this paper.

Jan 1, 2006

By G. H. McKay

AT the Eagle mine, near Gilman, Colorado, where the Empire Zinc Company have installed an underground mill, transportation problems were comparatively simple. A railway siding on the Denver and Rio Grande railway is equipped with an unloading dock or platform at the portal of their service incline adit to the mill. This 18-degree incline is approximately 600 feet long from the unloading track to the head of the mill skipway. For the Big Missouri mill, upwards of 2,500 tons of material and equipment had to be trucked from tidewater at Stewart, B.C., a distance of 21 miles to the Big Missouri camp at elevation 2,800. From that point, this freight had to be moved either over or through the Big Missouri ridge, rising to elevation 3,450, to its final location 800 feet from the surface between elevations 2,150 and 2,350. Immediately after leaving the government dock at Stewart, the road crosses the International boundary line into Hyder, Alaska, and then follows a water grade for eleven miles along the lower stretches of the Salmon river. leaving the river, the road climbs for two miles before crossing back into British Columbia territory at Silver Heights, and then continues for another mile and a half to where the Big Missouri road branches off from the main road to the Premier mine. For a distance of four miles from the junction of the roads, the Missouri road is very narrow, with many sharp curves and with irregular up and down pitches and grades up to 25 per cent until it reaches the Summit. From there on, a fairly easy grade leads a mile and a half to the end of the road on Joker Plats. In winter, the last stretch of road is subject to heavy snow drifting, especially through a narrow funnel-shaped gulch, known as 'The Gap', where the snow may pile up to a depth of over twenty feet.

Jan 1, 1938

By Thomas M. Ware

"MR. Chairman, our Honourable Minister, Mayor Cole, it is a pleasure for me to come here, and join with you in one of the largest industrial shows ever held in Saskatchewan.It is an honour to be asked to keynote your meeting, to help mark an early chapter of this new industry for Saskatchewan. God has placed in our hands a new resource for His man on earth. This store of potash, 350 million years in the making, offers a vital resource to help man support his advanced intellect for thousands of years. It is a gift so large we must all wonder at its purpose and our responsibilities in serving our fellow man with it.We who are here to plan and implement the development of this essential mineral resource enjoy a great -privilege; and we share a great responsibility -to see that the billions of tons of potash which have waited beneath these prairies for millions of years are widely and wisely used to nourish the earth through future millenniums.To know the true value of potash, to be able to bring forth this re-source from over 3,000 feet deep in the earth, to establish markets and develop its potential worldwide is all part of our great heritage from generations past. So I think it is fitting on this occasion that we reflect for a moment on this heritage, to help us assess the responsibilities of its future development."

Jan 1, 1966

By Derek V. Ellis, Jack L. Littlepage

"Marine ecosystem effects ar1smg from the discharge of man-generated wastes to the sea can be schematized as: acute poisoning, chronic poisoning, enrichment, suffocation, temperature effects, salinity effects, toxin bio-concentration, changed production rates and changed species equilibria. A professionally designed site-specific monitoring program to check for such effects can not only safeguard the marine ecosystem from degradation, but it can also protect the industry involved from unanticipated remedial action after expensive construction has been undertaken. Monitoring programs should consist of three steps. Step 1 is an ecosystem survey which should be undertaken prior to final design of the discharge system and submission of applications for permission to discharge, because there can be considerable cost savings in obtaining information at an early stage in development. Step 2 involves location of the effluent field at the time of starting discharge, and analysing its dispersal behaviour. Step 3 consists of ecosystem monitoring with sampling stations and specific tests based on the accumulated prior information."

Jan 1, 1972

By J. G. Mieczaniec

"A key element for a successful mining operation is the grinding circuit. It must be reliable, maintainable and must perform to or above design capacities for 95% of the time. Once chosen and installed major modifications are either prohibitive or very expensive. The selection of mills and drive system is probably the single most important decision made within the concentrator complex.Economic studies revealed that the optimum expansion for Lornex was a 68070 increase in plant throughput. This indicated that the new mill would have to be larger than the existing 32-foot mills.The Lornex ore has a wide range of hardness which has a great influence on mill throughput (Table 1). To smooth out the fluctuations, a blending program ha s always been in effect at the mine, coupled with ball charge control for the primary mills. As can be appreciated, an optimum balance is difficult to achieve. A sudden change to so ft ore with a high ball charge puts the mill into jeopardy with a constant speed drive.The blending philosophy would continue after the expansion, but with the addition o f a second primary crusher, it was envisaged to have the new mill process harder ore to maintain production targets. In theory, the new mill would have a proportionally larger ball charge than the existing mills.This scheme makes the new mill vulnerable for processing so ft ore for a fixed speed mill. Thus, variable speed seemed an attractive option.In early 1979 prominent mill manufacturers were invited to submit proposals for the new mill. Fixed and variable speed mills were to be considered with mill size ranging from 32-foot to 36-foot diameter. The proposals were to include the drive, ball charge, % critical speed, couplings, gears, etc. - the complete package. The recommendations were variable with most manufacturers submitting several alternatives. Recommended mill speed varied from 68% to 78% critical. The concept of variable speed was becoming more attractive, Lornex ultimately decided on a twin DC motor drive system for a 34-foot diameter mill.After start-up it was discovered that best throughput occurred at 78% mill critical speed or top speed of the drive motors. The motor speed range was adjusted upward from 186 to 200 rpm. Today the mills operate at 79% critical or a motor speed o f 193.5 rpm.Clearly the selection of the variable speed mill allowed the flexibility to optimize throughput."

Jan 1, 1985

By Mark Hollingworth

"There is general consensus that as the world continues to change at an ever-increasing pace, companies must continually adapt their operations in order to remain competitive. Those that change fast enough, survive; those that don’t, perish quickly. Today, we hear that it is not worth the time preparing corporate business plans as they are out-of-date before the ink is dry. Within the corporate environment of the 1990s, we must “think” strategically, be a “learning organization”, keep our costs low, focus on our core competencies, stay as flexible as possible and create value. So-called “sustainable competitive advantages” can be obsolete before a patent is issued — if its even worthwhile patenting the advancement. This is industry in the 1990s.Now, while all this radical change has been underway in the global industrial environment, what have Canada’s universities been doing to keep pace with the change affecting one of their major stakeholders? Have they adapted their products and services to suit the new market conditions? Have they built closer links to industry to try to understand how better to serve this important client? Do they welcome industry input as to how to redefine their mission, objectives, strategies or their course contents? Do their students graduate with skills ideally tailored for the global mining industry? In the era of communication, can they write high quality reports in English, never mind speak French or Spanish?In an effort to provide Canada’s engineering faculties with a “blueprint” for the future, the Canadian Academy of Engineering pre-pared a report entitled “Engineering Education in Canadian Universities”, published in August1993, which concluded with the following recommendations:"

Jan 1, 1996