Search Documents

The Porphyry Gold Mine (150km NE of Kalgoorlie) was reopened in November 1983 with production commencing in April 1984. Original reserves quoted for the open pit were 822000 tonnes at 5.2 g/t Au based on wide spaced diamond drill holes. Close spaced grade control drilling has revealed some loss of tonnage and a significantly lower grade. In the area of the pit mined to 30 June 1985 this grade control reserve estimate contained 67% of the gold in the original ore reserve with the grade being 19% lower. It is anticipated that the final grade control reserve estimate will contain around 80-85% of the gold contained in the original reserve. There has been close agreement between the Mill Head grade (4.19 g/t Au) and the grade control predicted grade (4.2 g/t Au) confirming that dilution is not a major problem. After initial poor agreement (attributed to "lock-up" in the circuit) the bullion calculated head grade steadied out at 93% of the grade control prediction. This difference is considered to represent the geostatistical bias in the drill hole/crushed rock sampling. Gold recovery has been in the range 93-95% (compared with bullion calculated grade). The net result is that the recovered grade of ore mined to 30 June 1985 is 70% of the original ore reserve grade.

Jan 1, 1986

Surface oxidation is one of the most important factors that influence the flotation selectivity and recovery in the processing of complex sulphide ores. It is an inherent part of surface chemical reactions that determine whether the surface film formed on a sulphide mineral will act as a hydrophobic or hydrophilic one. Because of the highly complex surface chemistry and mineralogy involved the results of flotation tests may often be difficult to interpret. In this paper, the flotation behaviour of nickel-copper ores processed in the Sudbury area is discussed with emphasis on the effect of oxidation on individual minerals, primarily pyrrhotite. In general, moderate oxidation of a freshly ground ore promotes the flotability of all principal sulphides in the ore leading to a bulk flotation concentrate. The ease of individual mineral flotability under normal aeration conditions, which is chalcopyrite > pentlandite > pyrrotite, changes to pentlandite > chalcopyrite > pyrrhotite under oxygen-deficient conditions. This behaviour is correlated with the catalytic activity of these minerals for oxygen reduction. On the other hand, preferential oxidation of pyrrhotite may lead to a selectivity increase in flotation. Such a behaviour has been noted in the flotation of a pyrrhotite-rich process stream. The results have been discussed in the light of fundamental electrochemical interactions involving pentlandite, chalcopyrite, pyrrhotite, pyrite and grinding media and a mechanism has been proposed to explain the selectivity.

Jan 1, 1993

Epithermal gold mineralisation was discovered at the Muyup prospect during regional reconnaissance exploration in 1986. Further exploration utilising routine techniques of stream sediment, panconcentrate, rockchip sampling and geological mapping resulted in the discovery of five auriferous vein systems located along northwest-trending fault zones. Scout diamond drilling was conducted on two of the vein systems. Mineralisation is hosted by a poorly exposed, mid-Tertiary volcanic inlier composed of intermediate and minor felsic volcanic rocks intruded by intermediate hypabyssal por- phyries. Gold is wholly contained in narrow steep-dipping hydrothermal breccias and quartz vein stockworks in which chalcedonic silica and fine grained quartz is the predominant gangue with minor adularia, carbonate, and sulphides. Alteration zoning is manifested as intense fracture-controlled silicification mantled by narrow clay-rich envelopes which in tam grade outward and downward into propylitic alteration or unaltered host rocks. Late advanced argillic alteration is superimposed on the vein-related altera- tion assemblages. Alteration assemblages and fluid inclusion data suggest that gold mineralisation occurred in response to episodic hydraulic fractur- ing and boiling of low to moderate temperature, dilute alkali-chloride fluids. The Muyup prospect represents the shallow eroded remnants of an epither- mal gold deposit enriched in Au, Ag, As, Sb and Hg. Low sulphur fugacities reflected by vein and alteration assemblages support an adularia-sericite classification (Heald et al, 1987) for this epithennal gold deposit.

Jan 1, 1991

By J J. McNee and, J Crusius, T F. Pedersen

The use of water covers is a globally-applied method for minimising acid rock drainage (ARD) and metal leaching. Although the subaqueous disposal of potentially acid-generating materials has been shown to effectively limit ARD, under certain scenarios, metal remobilisation can occur at circum-neutral pH. The following paper presents data from four case studies in which metal mobility from submerged mine waste resulted in degradation to water quality in the overlying water cover. Subcentimetre resolution profiling of dissolved constituents across the tailings-water interface (dialysis arrays), in conjunction with mineralogical information, were used to elucidate the controls governing metal mobility. The data illustrate four pathways of metal remobilisation, including: the release of zinc via the oxidative remineralisation of metal-rich organics at the tailings-water interface; enhanced remobilisation of arsenic as a result of anthropogenic eutrophication; the release of copper resulting from the pH-driven dissolution of treatment sludges; and the release of radium from uranium mill tailings due to the dissolution of radiobarite [(Ra,Ba)SO4] by sulfate-reducing bacteria. The results highlight the conclusion that the chemical stability of submerged tailings reflects both: the solid-phase characteristics of the tailings material; and the physical, chemical and biological characteristics of the depositional environment. In particular, the data illustrate that rigorous characterisation of both the waste solids and receiving environment must be performed in order to assess their compatibility. The results have relevance to the management of tailings repositories including constructed impoundments, pit lakes and natural lakes.

Jan 1, 2003

By B J. Monaghan, P Zulli, X F. Dong

In the lower zone of blast furnace (BF), slag trickles down through a packed bed of carbonaceous particles in the form of films, rivulets or droplets. During its downward flow, there are significant interactions occurring between slag and other phases, ie gas and packing particles. In particular, the interaction between gas and slag is closely associated with the key flow phenomena such as loading, flooding or channelling in the lower zone of the BF. With gas introduced laterally through tuyeres and slag flowing downward from the cohesive zone to the hearth, this interaction varies throughout the lower zone and in the cohesive zone:  strong cross-flow of gas relative to the slag occurs in front of the raceway  counter-current flow of gas and slag occurs in the upper parts of the lower zone  both strong cross- and counter-current flow of gas and slag around and within the cohesive zone. These interactions can be linked to furnace irregularities, affecting smooth operation and limiting production. Therefore, understanding the gas-slag interaction and its influencing factors remains critical for BF process control. In the current review, the physical behaviour and key influencing factors of gas and slag flow are initially examined. Numerical models describing gas and slag flows in a packed bed at micro-, mesoand macro-scopic levels, are reviewed. Each simulation approach has its advantages and limitations, as well as unique assumptions when used in BF process modelling. Applications of these approaches to gas-slag flow in key identified functional zones will highlight the differences between approaches and modelling outcomes. As no single approach can fully address all aspects of gasslag interactions, an integration of different approaches is considered an effective and beneficial method in providing a more complete understanding of gas-slag flow in the BF process.

Jun 19, 2024

By C E. Loo

The cohesive zone has a significant influence on blast furnace operation and performance. The high-temperature behaviour of the reducing ferrous burden determines the properties of the cohesive zone and is studied in a laboratory using a softening and melting test. This paper summarises recent work aimed at better understanding the physico-chemical changes in a ferrous bed during softening and melting. Using a combination of standard, non-standard and quenched tests supported by optical image analysis, this work has highlighted some important differences in behaviour between lump, pellets and sinter as well as between the two lump ores and two acid pellets. As with the two lump ores, one pellet is denser than the other and the denser ore/pellet is also higher in silica.Within the cohesive zone, densification of the ferrous layer leads to reduced permeability and greater pressure drop. From the work presented in this paper, two key mechanisms of ferrous layer densification were identified. Firstly, the formation of fayalite, which melts at low temperatures, can act as a lubricant between particles and lead to densification of the ferrous layer under load. Secondly, reduction to metallic iron is topochemical and fayalite in the outer shell of the particle restricts gas flow to the centre and results in the formation of a wustite core. As temperatures rise, the wustite melts and eventually exudes out of the shell, occupying void spaces between particles and further reducing layer voidage and permeability.This work has shown that density and silica content are two key factors that result in increased densification of the ferrous layer. For porous Australian lump ore, the higher porosity and lower silica reduces the formation of fayalite and limits the formation of the wustite core, ultimately leading to a more permeable bed. The difference between the porous and dense ores was more pronounced with the introduction of prereduction to better simulate blast furnace conditions. This suggests that a porous ore gives significantly better cohesive zone permeability and blast furnace operations than a dense ore.The behaviour of fluxed sinter particles is different in that the silica reacts with lime to form dicalcium silicate. Minimal wustite core forms because relict hematite particles in sinter are only small and reduction occurs uniformly throughout the particle. Even with significant loss of material through prereduction, beds formed from sinter remained comparatively rigid. Studies using a typical blast furnace burden mix of 80 per cent fluxed sinter and 20 per cent porous ore showed that the structures of these beds at softening and melting temperatures are very similar to the sinter-only test. Measurements of bed contraction and pressure drop also confirmed that the introduction of 20 per cent porous ore into a sinter bed did not alter its properties. This is an indication that 20 per cent ore can be easily accommodated by blast furnace burdens.CITATION:Loo, C E, 2015. Important acid ferrous burden properties in the cohesive zone of a blast furnace, in Proceedings Iron Ore 2015, pp 367–376 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By P Kumar, J Safarian

Understanding how ore interacts with flux particles at elevated temperatures to create molten slag is crucial since it governs the dynamics of a chemical reaction. This study explores the smelting behaviour of pre-reduced Nchwaning manganese ore when combined with lime, with the objective of examining the evolving interaction between pre-reduced ore particles and lime over time. The research sheds light on the interaction between solid and liquid and the phases that emerge during this process. To achieve this, a sessile drop furnace was employed to rapidly heat the materials positioned adjacent to each other on an alumina substrate and to observe the smelting process as it unfolded over time. This method allowed for the direct observation of the melting temperatures and the flux-ore reaction progression rate, and the potential disruptive events that might occur. By comparing the molten interfaces of the fluxed materials at various time intervals, this study provides insights into the relative rate of slag formation from the two materials. The results indicate that the main slag formation initiated at approximately 1400°C and continued to advance with time, with complete mixing occurring around 1500°C. The possible phases formed were identified using Scanning Electron Microscopy and modelled using Fact Sage thermodynamic software. In addition, the iron particles in the pre-reduced Mn ore were separated and settled from a rich MnO-containing slag. It was found that the separation of molten iron droplets from the slag depends on the rate of solid MnO particles dissolution into the adjacent slag phase.

Jun 19, 2024

By D Michaelsen, S Miller

The Grasberg Mine is a copper and gold open pit mine operated by PT Freeport Indonesia (PTFI) and located in the high equatorial mountains of the Indonesian province of Papua. The climate is alpine/subalpine with little seasonal variation in temperature or rainfall. The daily average temperature ranges from about 2¦C to 14¦C and the annual rainfall in the vicinity of the mine and overburden stockpiles is about 4000 mm to 5000 mm. Mining of the Grasberg open pit will continue until 2014 at which time approximately 2750 Mt of overburden will have been produced. Current overburden production rates are 200 Mt per annum. The current mill rate is 230 000 t/day from the Grasberg pit (190 000 t/day) and the underground operations (40 000 t/day). The acid rock drainage (ARD) issues associated with overburden from the Grasberg operations were identified early in the mining operation. Almost all overburden placed to date has been Potentially Acid Forming (PAF). Laboratory testing has identified four main overburden types: limestone and non-acid forming (Green waste), PAF low capacity (Blue waste) and PAF high capacity (Red waste), and Heavy Sulfide Zone (HSZ), which contains greater than 20 per cent pyrite. Waste type block modelling indicates that at least 30 per cent of the overburden production from 2003 to the end of Grasberg pit operations will be limestone. Strategies are being developed to maximise the beneficial use of limestone through strategic blending and placement for ARD mitigation and control.

Jan 1, 2003

By G R Ryan

Recent events have raised the issue of whether, and if so when and how, an explorer may gather data from a mining tenement or permit which is held under the relevant mining Act by another party. Two situations arise: that of the small operator who wishes to prospect, and if successful mark off, ground held by others by virtue of the local form of exploration permit; and that of a regional explorer who may wish to enter on to some one else's existing mining tenement within the region of interest. The legal situation varies from state to state. At present the broad consensus seems to be that, provided consent is given, small-scale prospecting on another's exploration permit is at least tolerated if not actually provided for by the relevant Act. Entry onto a granted tenement to carry out any form of exploration is, however, prohibited in all jurisdictions unless consent is given. Furthermore it would appear that the proposal and conclusion of a joint venture agreement places certain obligations upon the party proposing to carry out exploration. These conclusions apply where ground surveys are proposed. Where data acquisition is by aerial survey the situation is much less clear, principally it would appear, because up to now little thought has been given to it. If trespass applies at ground level, at what height does it cease to apply? Can aerial magnetometry or photography be classified as prospecting? Is there an obligation upon public authorities who carry out remote sensing to make data available to the holders of mining tenements within the surveyed areas? Moves are now afoot to address these and other considerations, and it would be in the interests of everyone if a national approach to the problem could be adopted from the beginning. Certain suggestions in this respect are put forward.

Jan 1, 1994

By D K, S Freij, A Rossiter, X Han, B Feng

In mining operations, the removal of overburden to expose the ores is achieved by rock blasting using ammonium nitrate based explosives, eg ammonium nitrate-fuel oil mixtures, commonly known as ANFO. However, ammonium nitrate can react with pyritic shales that are often found in many mines, leading to premature detonation or spontaneous explosion. In order to minimise the occurrence of spontaneous explosion, the reactivity of the shale in a mine must be assessed. This will provide a better understanding of blasting risks and thus will improve the safety and the cost efficiency of blasting through the selection of appropriate explosives. In this study, shale samples were collected from different locations in Western AustraliaÆs Mt Whaleback iron ore mine and geochemically characterised. The reactivity of the shale samples towards ammonium nitrate and ANFO was investigated using a combination of large-scale firing range tests and laboratory isothermal reactor tests. Results of the firing range tests show that the reactive ingredients of the shale are the limiting factor for the reactions between shale and ANFO. Based on the firing range test results, further isothermal reactor tests were conducted to investigate the reactivity of shale samples towards ammonium nitrate under controlled conditions. Analysis of the results from the firing range tests and the isothermal reactor tests shows that there are correlations between the reactivity of shale samples and several geochemical characteristics such as sulfate, sulfur, ferrous and zinc content.

Jan 1, 2005

On 15 August 1998 the first section of the PUTRA LRT system was opened to the public as a free service prior to official commencement of revenue service on 1 September 1998. It is a remarkable achievement to open a highly advanced medium capacity urban railway scheme in four years after the outline concept began. Even more remarkable is the implementation of the next stage which is the underground section planned to be operational in mid-1999. The decision to build the first underground railway in any major urban centre is a technical challenge. The PUTRA LRT System can be likened to Hong Kong when the initial MTR system began in the 1970s and Singapore MRT in the 1980s. Prior to the PUTRA railway very little bored tunnelling had been undertaken in Kuala Lumpur. A few shallow sewer tunnels had been built but the main experience of tunnelling in Malaysia had been for water, hydroelectric and road tunnels usually through granite formations. The ground conditions in Kuala Lumpur were known mainly from experience of piled foundations and occasional deep excavations. The suitability and likely difficulties to be experienced during bored tunnelling could only be theoretically predicted. In both Hong Kong and Singapore, government owned corporations were set up to implement the scheme, but in Kuala Lumpur the whole project has been undertaken by a private company PUTRA, a wholly owned subsidiary of Renong Berhad.

Jan 1, 1999

By D Chalmers

After the sustained use of the GAG (Górniczy Agregat Gaśniczy) engine at a Queensland coalmine, it has raised questions as to its effectiveness as a remote firefighting tool. All firefighting apparatus have advantages and limitations, however the deployment of any apparatus must be based on its likelihood to succeed and effectively extinguish the fire or bring it under control. A recent study conducted for ACARP by researchers at UNSW has highlighted that there is more to be learned about the GAG. As coalmines are mining at greater depths and fan pressures are much greater than they were when the GAG was introduced, deploying the GAG may be a total waste ofresources and may place operators at greater risk. When the GAG unit is positioned on the surface of the mine, the pressure it generates has to overcome buoyancy of the exhaust gases and the frictional resistance of the borehole and part of the mine circuit. Buoyancy in deeper holes can lead to the GAG pressure relief system opening, venting out the products to the atmosphere without delivering any product to the mine workings. Additionally, frictional resistance is a function of distance. Deeper holes will have a greater frictional resistance than shallow holes. Delivering sufficient products from the unit will be limited by the available pressure that has to overcome the buoyancy, and increased mine resistance thatconsumes any residual pressure. By documenting the limitations of this unit it will enable better decisions to combat a fire or spontaneous combustion event.

Oct 12, 2022

By B Indraratna, A Dey

The surface geometry of a rock bolt plays a very important role in the rock/resin/bolt load transfer mechanism. Very little work has so far been reported on the influence of the bolt surface geometry on the bolt/resin interface failure mechanism. This paper examines the behaviour of bolt surface roughness under constant normal stiffness condition in the laboratory. To study the shear behaviour of the bolt/resin interface a series of shear tests with an initial normal stress between 0.1 to 7.5 MPa has been conducted on the flattened bolt surface of two most popular bolt types currently being used in Australia. Bolts with deeper ribs offered better shear resistance at low initial normal stress conditions whereas bolts with shallow and closer ribs offered better shear resistance at high normal stress conditions. The maximum dilation occurred at a shear displacement of 60 per cent of the rib spacing irrespective of the bolt type and depth of the rib.

Jan 1, 2000

By N Voller, A Ishmurzin, G Hackl, M Wu, A Kharicha, M Chintinne, C M. G Rodrigues, A Ludwig

Slag fuming (SF) is a critical process for recycling zinc-containing slags, but the corrosive nature of molten slag poses challenges to the reactor durability. The freeze-lining (FL) technique offers a solution by forming a protective layer on the reactor wall. It requires intensive cooling using watercooled jackets, which can stabilise the FL while compromising the energy efficiency of the process. This study presents a computational fluid dynamic (CFD)-based model to optimise the SF process by considering FL formation and its impact on heat transfer and reactor wall temperature. A volumeof- fluid (VOF) model is coupled with a mixture continuum (MC) solidification model to capture the intricate multiphase flow dynamics within the SF furnace. Two FL types are considered: FL solidifying on the reactor wall in the slag bath region; and FL solidifying on the reactor wall in the freeboard region. The FL of the first type forms when the slag temperature drops below liquidus temperature. The FL of the second type only forms when a splash-induced slag droplet collides with the freeboard wall and solidifies. A series of splashing events are necessary to coat the freeboard wall. The simulation was run until a global energy balance was reached. This means that the heat losses from the water-cooled jacket, bottom wall, outlet and fuming balance the heat gains from the hot gas injected through the submerged plasma torches. The increase in FL thickness, due to its low thermal conductivity, reduces the heat losses through the reactor walls. The calculated FL thickness and heat fluxes were in good agreement with industrial data, validating the model’s credibility. The simulation results provided valuable insights into the fuming process, including slag bath temperature evolution, slag splashing dynamics, FL formation patterns, local heat fluxes through the reactor wall and overall energy balance. These findings can inform process optimisation strategies to enhance the energy efficiency and sustainability of SF operations. The authors have built a prior version of the model framework and applied it to simulate FL formation in an electric smelting furnace (ESF). The results from both the ESF and the current SF highlight the applicability of such model framework to a range of industrial processes involving FL formation. This model framework can ultimately contribute to more energy-efficient and sustainable industrial operations.

Aug 21, 2024

By Lloyd F, Arnold D. A, Hagan T. O

This paper investigates the problems that are encountered in mining at extreme depths. It looks into the rock mechanic aspects, especially the high stress levels that will occur, and the hazard of rockbursts. Furthermore, environmental problems are discussed, with refrigeration and reduction of neat loads being major methods of maintaining ,sorkable conditions. The paper concludes that it will be of tmost importance to have a planning team of Tne highest quality to ensure that conditions are maintained so that work can be carried out safely and under reasonable conditions.

Jan 1, 1986

By J Zhao, C E. Loo

The flame front is a narrow region in the iron ore sintering bed where coke particles combust. The maximum flame front temperature is as high as 1400°C. At high temperatures, the sinter mix components react to form melts, which facilitates material coalescence and the formation of dense sinter particles. It is well-established that flame front speed is an important factor influencing sinter productivity, sinter quality and fuel rate. In this work, the effect of suction, coke addition and mix moisture on flame front speed was studied in a pilot-scale sinter pot and also using the outputs of a recently developed theoretical model, which takes into account most of the significant physicochemical processes in sintering. Airflow through the bed has a large influence on flame front speed. A power law relationship between these two parameters means that increasing sintering airflow rate will lead to increased flame front speed, but the increases become smaller at higher airflow rates. Sinter pot test results showed that increasing coke addition decreased green bed permeability and increased flame front temperature, which resulted in increased flame front resistance and decreased flame front speed. Studies also showed that green bed properties are sensitive to sinter mix moisture level. The changes in green bed properties further influence the flame front speed and temperature.CITATION:Zhao, J and Loo, C E, 2015. Dependence of flame front speed on iron ore sintering conditions, in Proceedings Iron Ore 2015, pp 83–90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By T Higuchi, K Fukada, K Takehara, Y Iwami, S Fujiwara

Following the Paris Agreement adopted in 2015 and the SDGs, reduction of CO2 emissions has been taken up as an issue worldwide, and the steel industry, which has a particularly large emission, is required to significantly reduce it. Most of the CO2 generated in the steel industry is generated from the ironmaking process, due to the use of coke and its raw material coal in the ironmaking process. JFE Steel Corporation has been considering the use of hydrocarbon-based gaseous fuels and liquid fuels as a partial alternative to coke breeze used in the sintering process since 2006, immediately after the Kyoto Protocol came into effect in 2005. In a laboratory study, a pot test was used to investigate the effect of the type of fuel, its amount and its injection method on the heat pattern in sinter bed. As a result, the authors developed a technology, in which a predetermined amount of gas fuel or liquid fuel was injected from the surface of sintering bed to extend the holding time of 1200°C or higher at which liquid phase sintering occurs in the layer, to improve the sinter strength while reducing the amount of coke breeze. The authors succeeded in putting this technology to practical use using hydrocarbon-based gas fuel in 2009 and achieved a maximum annual reduction of 60 000 tons of CO2 per sintering machine. In this report, the authors introduce the results of laboratory studies on the use of various energy sources, the practical application of the technology for injecting hydrocarbon-based gaseous fuel into the sintering machine, and the operational results.

Nov 8, 2021

Upgrading of MgO in Dolomite Ore by Froth Flotation

Sep 13, 2010

By G J. Jameson, A Agarwal

This paper is concerned with the observation and analysis of bubble clusters in a laboratory flotation cell. A device was used in which bubbles were allowed to rise in clean water containing the same frother and collector concentration as in the cell. Bubble clusters were recorded using a high speed camera and analysed using an image analyser. Dodecyl amine was employed as a collector to float silica. The effect of impeller speed on the cluster behaviour was investigated. The results were interpreted in terms of cluster diameter and shape factor. The sizes of the bubbles forming the clusters were also measured and compared to the sizes of the independent bubbles in the cell. It was found that there was an optimum impeller speed in which the cluster diameter was a maximum. Higher agitation and the consequent higher power inputs resulted in cluster break-up while lower shear rates promoted cluster formation.

Jan 1, 2005

By B Godel, E R. Ramanaidou, M Verrall

Fortescue Metals Group Ltd Iron Bridge (IB) operation is a magnetite deposit located in the Pilbara region of Western Australia situated around 145 km south of Port Hedland. This Mesoarchean deposit belongs to the 3230 Ma Pincunah banded-iron formations (BIF), a member of the Kangaroo Caves Formation, Sulfur Springs Group (van Kranendonk, 2000).

Sep 18, 2023