Search Documents

By Tomlinson R. C

There are two main aspects of coal preparation to which the operational Research Executive of the National Coal Board has applied computer models. The first is in the planning of preparation plants and the first part of this paper discusses Simprep, a computer package that was designed to help on these calculations. The other is the development of control schemes to improve quality control, and the second part of the paper deals with the development of simulation techniques for this purpose.

Jan 1, 1977

By Cox I

Raiseboring is a technique that has become popular in modem mining engineering since the early 1960s. A study has been undertaken at the University of Queensland to determine important factors affecting the optimum diameter of raisebored shafts, excluding local parameters such as the maximwn excavation size that a particular rock type can safely accommodate.This model is used to examine each of these factors and the results indicate that the optimum diameter for raisebored shafts is generally between four and six metres.

Jan 1, 1991

By J Demchak, L M. McDonald

The duration of acid mine drainage flowing out of underground mines is important in the design of watershed restoration and abandoned mine land reclamation projects. People conducting land reclamation projects usually employ remediation strategies once (reshaping land, revegetating soils, and installing water treatment) with the hope that these methods will adequately improve water quality for a long time, with little planning for future changes. An understanding of changing acid water conditions from underground mines over time will help in designing efficient and cost-effective treatment methods. Past studies have reported that acid water flows from underground mines for hundreds of years with little change, while others state that poor drainage quality may last only 20 to 40 years. Several factors are important in making a prediction of drainage quality over time, such as inundation or flooding history, coal seam characteristics (primarily sulfur content), residence time of water in the mine, time since mine closure, mining method and amount of coal remaining, collapse of roof and other disturbances within the mine, and subsequent nearby surface mining. More than 150 above-drainage (those not flooded after abandonment) underground mine discharges were located and sampled during 1968 in northern West Virginia, and we revisited 44 of those sites in 2000 and measured water flow, pH, acidity, alkalinity, Fe, Al, and sulfate. All 44 discharges were from mines in the Pittsburgh and Upper Freeport coal seams, and both seams have been extensively mined in this area during the past 70 years. We sampled during the same months (June to October) as were sampled in 1968, and we found no significant difference in flows between 1968 and 2000. Therefore, we felt that the water quality data could be compared and that the data represented real changes in pollutant concentrations. There were significant water quality differences between year and coal seam, but no differences between disturbed and undisturbed mines. Average acidity declined 79 per cent between 1968 and 2000 in Pittsburgh mines (from 3342 to 702 mg/L), and 56 per cent in Upper Freeport mines (from 1189 to 519 mg/L). Iron decreased an average of about 80 per cent across all sites (from an average of 345 to 69 mg/L), while sulfate decreased between 50 to 75 per cent. Pittsburgh seam discharge water was much worse in 1968 than Upper Freeport seam water. Twenty of our 44 sites had water quality information during 1980, which served as a midpoint to assess the slope of the decline in acidity and metal concentrations. Almost all parameters showed an exponential rate of decline in acidity, iron, and sulfate.

Jan 1, 2003

Of all of the processes in the mining cycle, blasting has the greatest impact on the efficiency of both mining itself and the initial stages of ore processing. The cost of blasting can be readily accounted for, but the true benefits of an effective blasting operation are seldom measured or reported. This means that blasting is seldom optimised in terms of its overall economic impact on an operation. Blasting operations have evolved according to the environment provided by mine management. Most operations seek to minimise the unit cost of each component process (overburden removal, blasting, excavation and transport, crushing or grinding) without recognising the impact that blasting performance has on subsequent activities. The creation of æcost centresÆ or æmanagement unitsÆ that isolate blasting from its downstream impacts reinforce this trend. Modern blasting technology is regarded as sophisticated by virtue of the mechanical design of the drills, the chemistry of the explosives and the flexibility and reliability of modern blast initiation systems. However, blast performance is controlled by the nature of the rock mass and there is generally an inadequate appreciation of how blast designs should be tailored to suit different rock mass conditions or to meet different blasting objectives. Most operations utilise a limited suite of standard designs without routinely tailoring designs to suit the actual conditions at hand or the objectives of each blast. Mining operations would benefit from tackling the following specific challenges:What is the appropriate target performance for blasting operations to generate the maximum economic benefit for the operation as a whole? How should designs be configured to suit the changing rock mass conditions and operating constraints? What compromise (if any) should be allowed from the ideal to assist conflicting scheduling or other operational requirements? How can blast performance be measured and reported to provide appropriate guidance to future operations? These challenges can be tackled through the process of æblast engineeringÆ. This paper discusses the potential impact of blasting performance on the economics of mining operations and the author argues that very considerable benefits over and above those currently being achieved could be realised by improving the routine engineering of mine blasts. The paper then explores how the industryÆs failure to recognise the economic importance of blasting has resulted in the engineering of blasting operations receiving less management and technical support than is appropriate. Finally, a simple approach to the engineering of routine blasting operations is described as an example of how these challenges can be tackled.

Jan 1, 1999

By C M. Côte, P Bolz, L Pagliero, M Edraki, M Shaygan, P Erskine

Mines in Queensland must now prepare a Progressive Rehabilitation and Closure (PRC) plan, with the requirement to justify the selection of the post-mining land use (PMLU) for each rehabilitation domain. Given that there are nearly 200 mines who must undertake a comprehensive PMLU assessment, there is a need to develop methods that will minimise the duplication of effort. As part of a broader initiative on innovative post-mining land use planning, this project undertook a regional analysis of the technical suitability of several PMLUs.

Aug 2, 2023

By N Madani, N Battalgazy

Geostatistical simulation has been widely used in mineral resource classification of metalliferous deposits based on international standards such as JORC code which is one of the most extensively used around the world for reporting the mineral resources and ore reserves alongside with objectives of the companies (Sadeghi, Madani and Carranza, 2015). However, the modeling process becomes challenging whenever the relationship between the variables of interest is complicated and cumbersome to model. This characteristic sometimes manifests itself in complex spatial and global cross-correlation measures, deeply depending on the formation and genesis of the deposit. The objective then is to generate the models that not only reproduces these significant characteristics, but also, it leads to a better understanding of a mineral resource estimation and successive decision-makings. In this respect, there are different approaches taking into account the spatial correlation structures, for which can be classified as independent simulation, co-simulation, and factor-based methodologies. In this paper, three techniques: Turning Bands Independent Simulation (TBSIM), Turning Bands Co-Simulation (TBCOSIM) and Projection Pursuit Multivariate Transform (PPMT); from those aforementioned approaches are selected to model two cross-correlated variables (Iron and Aluminum Oxide) belonging to an Iron ore deposit located in Brazil, in order to examine which methodology better reproduces the corresponding complexity in terms of local correlation measure. CITATION: Battalgazy, N and Madani, N, 2018. Mineral resource assessment in complex ore deposits based on international standards, in Proceedings Complex Orebodies Conference 2018, pp 79–81 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

The accuracy with which block values are known can have a fundamental effect on the success of an operation.From a geostatistical study the variance of the error in extending sample values to block values can be determined and the engineer must ensure that this is sufficiently small by adjusting the size of blocks or moreintensive sampling. A study is given for a deposit showing a high degree of anisotropy and it is shown that the shape of the block is not important in determining the estimates.

Jan 1, 1976

By Arbuthnot IM

It is the commonly held belief that, because the separation of liquids from solids takes place considerably faster in high rate thickeners than in conventional thickeners, high rate thickeners (HRT's) must use more flocculant than conventional thickeners. Data collected from a wide range of thickener users in Australasia and data presented in the literature is analysed. In addition, pilot plant data, with direct comparisons between HRT's and conventional thickeners, is presented. It is concluded that the flocculant consumption for both thickener types is in the same range.

Jan 1, 1991

By Lewis RW, Wilson GI

An ore reserve estimation is only as meaningful as the quality of the data used. All required information needs to be collected in a careful and systematic manner, and be rigorously checked and verified before estimation commences. In addition to geological, assay and location data, a large variety of other information is required for the estimation process. This includes mining, metallurgical and environmental parameters. Though outside their usual area of responsibility, geologists should be involved in the selection and collection of this additional Information.

Jan 1, 1987

The availability of three-dimensional computer hardware and software makes the solid modelling of geological entities a realistic and logical alternative to previous sectional and plan 'models'.The success of underground mining operations depends largely on the ability to accurately predict the three-dimensional location and grade of mineralisation in order to maximise the extraction of resources and minimise mining dilution. The integration of lithological, geotechnical and grade models into three-dimensional solid models provides an excellent basis for underground mine planning and operation

Jan 1, 1993

Deformation of the lithosphere by tectonic forces is investigated from both observational and theoretical standpoints. Global and regional geophysical data bases, coupled with the means for their rapid display and analysis, facilitate recognition of areas of the con- tinents and oceans where the response of the lithosphere to these deforming processes might fruitfully be studied. Gravity anomalies, from Seasat altimeter data and from land and shipboard measurements, provide critical infor- mation on the isostatic state of deformed lithosphere and therefore on its thermal and mechanical properties.

Jan 1, 1987

The competitiveness and future growth of the Australian mineral resources industry face a number of challenges. The paper addresses key factors likely to influence the attainment of high performance and continuous improvement including organisational leadership, management/employee relations, technology, safety, health and the environment. Business practices such as benchmarking, Total Quality Management and re-engineering to achieve process and performance improvements are commented on. Future success for the industry will largely hinge on global business skills, a sustained focus on Quality principles and achieving performance through people.

Jan 1, 1997

Portman Mining Pty Ltd very successfully operated the Ferro GullyNorth Mine in the Hamersley Province of Western Australia to satisfy a contract for the delivery of six million tonnes of iron ore in less than two years to the Mount Newman Mining Co Pty Ltd. The high-grade ore extracted from Ferro Gully North Mine was unusual in that, not only was it within the Joffre Member of the Brockman Formation, but it was rich in red ochreous hematite and martite and very low in phosphorus.

Jan 1, 2001

By R Uken G P Whitmore

The coastal dune cordon of northern KwaZulu-Natal is amongst the highest in the world reaching heights in excess of 180 m and up to 2 km in width. It comprises a complex system of Quaternary stacked dunes of various geomorphologies, types and ages. The dunes contain economic heavy minerals which are currently exploited ~20 km north of Richards Bay. Although mining of these ore sands has been in operation for the last two decades, little work has been undertken on the clay-fraction (

Jan 1, 2001

By Orrock G, McKee DJ

Mathematical models of autogenous and semi-autogenous grinding mills have now reached a stage of development where they can be usefully applied to practical problems. In particular, the models are suitable for inclusion in simulations of grinding circuits to study the effects of cir- cuit changes, variations in ore type and changes in throughput. The paper describes a simulation study of the Elura grinding circuit where the empha- sis was on investigating methods of reducing product size from an autogenous mill-ball mill grinding circuit.

Jan 1, 1988

North Stradbroke Island is a large sand mass offshore from south east Queensland. Dredging for mineral sands commenced there in 1956 and the rehabilitation discussed in this paper was commenced in 1967. The frontal dunes have a long history of instability, with little vegetation prior to mining. Re-establishment of the naturally stable contours is essential, and their rehab- ilitation is described. Vegetated high dunes present different problems requiring attention to regeneration of the native species. Methods developed over the past eight years are proving successful.,

Jan 1, 1976

By Roderick W. F

The equipment and procedures used for green pellet production on a laboratory scale are given, together with a description of the straight grate pellet strand analogue which has been developed to examine the response of various ore types to heat hardening. The capabilities of the analogue are illustrated with data obtained from the balling and drying studies using a manganese ore. Differences in inter-batch pellet quality are discussed, and method of minimising the experimental error that can arise from these differences is Presented.

Jan 1, 1974

ICI Australia has been developing PC-based software to assist the blast engineer to design and monitor open pit blasts. The scope of this software differs significantly from commercially available mine design packages.The software is designed for routine use in a normal production environment. The system enables the engineer to produce practical documents which include: a drilling plan, a loading sheet, a hook-up diagram, an inventory of explosives and auxiliary items, and other data on the blast such as tonnages and powder factors.

Jan 1, 1992

By Turnbull AG

The direct smelting of zinc sulfide con- centrates has been investigated by an extensive series of computer-based thermodynamic equili- brium calculations. The study covers both pure 7.n-S-O-C-N systems and practical concentrate- coal-air-flux systems. It is shown that for a zinc concentrate containing iron and lead sul- tide impurities, a 97% yield of zinc vapour with autogenous operation can be obtained under carefully optimized conditions. The possible integration of this process with existing zinc condensation and recovery processes is Discussed.

Jan 1, 1980

By Parker RJ, Swindells CF

The authors have used the geotechnical study for design of the South Wall of Mt. Newman Mining's Mt. Whaleback Mine to illustrate how geotechnical studies can be economically justified. This is achieved by relating the savings resulting from increased ore recovery and prevention of failure to the cost of the study. An outline of the geotechnical study is provided in the paper, including a brief description of the innovative methods used to investigate geological structure of the mine and descriptions of the methods of slope reinforcement adopted.

Jan 1, 1986