Search Documents

By Mutmansky J. M, Hartman H. L

Multiple operating points for mine fans are a problem that fan and mining engineers must constantly be aware of in mine/fan systems. In a single-fan system, unstable conditions can be avoided by restricting fan operation to the "normal operating range." When mine fans are operated in parallel, the situation becomes a little more complicated. Multiple operating points are more often encountered and the fan user must be aware of these multiple points to have a suitable set of operating conditions. However, for fans in parallel, the engineer can plot the combined characteristic in a relatively straightforward manner and thus can avoid conditions that would cause instability in the mine/fan system.

Jan 1, 1988

By Hikosaka A, Chiba A

In a fundamental study of the physical chemistry of steelmaking slag, equilibra bet- ween hydrogen-water vapour gas mixtures and liquid slags contained in solid iron crucibles have been measured for four binary slags, FetO-CaO, FetO-Si02, FetO-TiO2 and FetO-Al203 at 14000C. From the data, the activity of iron oxide and the ratio of ferrous and ferric ions (A = Fe3+/Fe2+) were calculated for the slag composition. The best ionic model is found to be that based on regular solution of cations. The oxygen distribution between slag and metal is quantitatively expressed by this model over a wide range of slag composition.

Jan 1, 1980

By Mandzic E. H

The Dome Mine of Timmins Mining company is located in South Porcupine, N.W. Ontario. The orebody being mined partially lies in the No. 3 shaft pillar. Stability analysis has been carried out to establish the influence of nearby mining on ground movement in the shaft vicinity. Mathematical modelling of shaft displacement has been done for stope layout at depths from 180-210 m and distances of 10-50 m from the shaft. Analysis indicated that ground displacement around the shaft is below 1 mm/m and one third less for cut and fill than in the case of open stope mining. The result of the investigation was later confirmed by cut and fill mining of this orebody.

Jan 1, 1986

Norway, a country large in area but small in population, has put large effort in protect- ion of its inhabitants in case of war. The Civil Defence has provided shelters for more than 50% of the population. Some of these shelters are put into rock. Since rock installations give large resis- tance against weapon effects and also by advan- tage can be used for several purposes in peace- time, an interesting development has taken place the last decades. In towns and cities you will find sport halls, swimming pools, bowling and shooting ranges etc in rock, which easely can be conver- ted to civil defence shelters. Some typical installations are highlighted in the following.

Jan 1, 1987

By Pathan AG

This research work is concerned with an investigation of the fracture toughness of sandstone, siltstone, and coal. Tensile failure trades have been examined with three different specimen geonetries, i.e; rectangular bar, round bar (in three point bending), and diametral compression discs. The Stress intensity approach, and J-integral methods were used to evaluate fracture toughness. Results from both approaches are discussed. True crack length was determined after pre-cracking, using the compliance calibration technique. Fracture toughness results of sandstone are independent of crack length and the size of the specimen. Fracture toughness may hence be regarded as a material property for sandstone. In cxnntrast fracture toughness values for !siltstone and coal are dependent on crack Length.

Jan 1, 1986

The recent installation of top gas temperature probes in blast furnaces at Australian Iron & Steel Pty. Ltd. - Port Kembla, has provided the means for studying radial gas flow distribution in blast furnace shafts. This paper describes the top gas temperature probes and outlines their development and results of initial studies aimed at obtaining a suitable relationships between temperature profiles and furnace parameters. The effects of various combinations of burden materials have been outlined by the results reported. The use of probes has also helped to clarify the effect of casting cycles on furnace operation leading to increased emphasis on the reduction of the interval between gun-up and drill-out. Areas for future studies are also broadly Outlined.

Jan 1, 1975

By Kennewell G. J

This paper aims to present the evolution of the mining method in the Prince Lyell orebody. Initial strategy and practical experience are detailed as are the reasons for and benefits of changes to the method since 1972 when underground mining began. This section of the paper starts with ten series and concludes with 40 series which was completed in 1989/90.In addition, to update the series of papers written by various authors over the past ten years on Mount Lyell, a review of the experience in the current 50 series lift of mining will be given. As well, the basic planning guidelines are discussed for 60 series - the final lift of the Prince Lyell orebody.

Jan 1, 1992

The results of a systematic geochemical survey of rare elements are applied to elucidate genetic relations in a suite of rocks and to predict the probability of mineralization. The geology, radioactivity, major element geochemistry and classification of the main intrusives are described. The distribution of a group of rare elements, their concentration trends and the bearing these have on the emplacement sequence of the rocks are considered in some detail. The guides for exploration in the Pilanesberg that emerge are listed and some areas which substantiate predictions are described briefly. It is concluded that a study of rare element trends can make a considerable contribution as an exploration tool and for clarifying relations between the members of rock suites.

Jan 1, 1986

By Y Wan, L Liao

Organo-montmorillonites were synthesised by intercalating different amounts of dodecyl trimethylammonium bromide, cetyl trimethyl- ammonium bromide and stear trimethylammonium bromide into montmorillonite layers, and were used for the adsorption of 17b-estradiol in aqueous solution. The adsorption kinetics and thermodynamic of 17b-estradiol onto organo-montmorillonites and the effect of pH on the adsorption capacity of organo-montmorillonites for 17b-estradiol were studied. The adsorption isotherms at 20¦C, 35¦C and 50¦C were measured. Results show that organo-montmorillonite has a high affinity for 17b-estradiol. More 17b-estradiol can be adsorbed on to organo-montmorillonite and the adsorption is more rapid at a lower temperature. The montmorillonite intercalated with cetyltrimethyl- ammonium bromide with the amount equivalent to one times of its CEC has the highest adsorption capacity. For all organo-montmorillonites synthesised in this study, an optimum pH (around nine) for the adsorption of 17b-estradiol exists. Before this pH 17b-estradiol uptake increased with increasing pH. After that the 17b-estradiol uptake decreased with increasing pH. Simulation of the isotherms indicated that the adsorption of 17b-estradiol onto organo-montmorillonites is a spontaneous and exothermic process. Endocrine-disrupting chemicals (EDCs) are the focus of current environmental concern, as they can cause adverse health effects in an intact organism, or its progeny, subsequent to endocrine function. Most EDCs are man-made organic chemicals (industrial chemicals, crop protection products, antifouling compounds, pharmaceuticals and personal care products). In addition, EDCs can be naturally occurring in the environment (eg the natural female hormones estrone and 17b-estradiol). Therefore EDCs, especially estrone and 17b-estradiol, are ubiquitous in the aquatic environment receiving sewage inputs. Estrogen and 17b-estradiol are among the most potent of all EDCs and are sufficiently stable to survive present sewage treatment processes and are reactivated during those processes through deconjugation (Clara, Strenn and Saracevic, 2004; Zhang and Zhou, 2005; Fukuhara et al, 2006; Butler and Guilbault, 2006; Volpe et al, 2006; Ren et al, 2007; Zeng and Li, 2007). In comparison to traditional contaminants such as pesticides, the concentrations of the most potent EDCs are low, generally within ng/one range. The current sewage treatment processes have limited capacity in removing certain EDCs (eg 17b-estradiol, C18H24O2) It is therefore essential to install additional treatment processes to remove them from wastewater before discharge (Zhang and Zhou, 2005; Fukuhara et al, 2006; Lee, Jung and Kim, 2006). Adsorption is considered to be a possible way to remove EDCs from aqueous solution. Various adsorbents have been studied, including chitin, chitosan, ion-exchange resin, activated sludge, activated carbon (Clara, Strenn and Saracevic, 2004; Yoona and Westerhoffa, 2003; Zhang and Zhou, 2005; Fukuhara et al, 2006; Ren et al, 2007). Studies have shown that organo-montmorillonite has a high affinity for organic pollutants (Li, 1997; Zhu et al, 1998; Han et al, 2001). The aim of this work is to investigate the feasibility of removing 17b-estradiol from aqueous solution by adsorption onto organo-montmorillonite.

Jan 1, 2008

By J Lane, D J. Barker, B Pei

Queensland Alumina Limited (QAL) is the worldÆs largest producer of smelter grade alumina, located in Gladstone, Queensland, Australia. The plant employs evaporative cooling towers for waste heat rejection. Process water requirements include red mud residue disposal, steam venting to the atmosphere and Calcination feed moisture. Raw (untreated) water consumption in 2001 was 37 700 m3/d or 3.8 m3 per tonne of production. The Gladstone region experienced a water shortage in the period 2001 to 2003, resulting in progressive water restrictions. Industry operated under a ten per cent restriction from April 2002 and in November 2002 a 25 per cent restriction came in force. The maximum restriction level of 50 per cent was anticipated for the middle of 2003. Water restrictions of these magnitudes have the potential to result in significant production limitations, which would have major economic consequences for QALÆs owners, customers, suppliers and employees. Therefore it was imperative that measures be found to mitigate the impact of these restrictions. Furthermore, as one of the largest water users in the Gladstone region, QAL had an obligation to the community to minimise water usage as much as possible. A thorough analysis of water usage on site was conducted, focussing on all water streams leaving the plant. The philosophy used was that by minimising water outputs, the inputs would follow suit. Where possible, preference was given to solutions that provided lasting water savings. This occurs when the value of the water saving justifies the project cost, irrespective of water restrictions. By June 2002 an average water saving of 19 per cent was achieved, almost double the required saving. By end November 2002 further projects had increased the total water saving to 29 per cent, mainly through the re-use of GladstoneÆs municipal treated effluent as wash water. Further measures to reach the target of 50 per cent reduction were investigated. The evaporative cooling system was to be replaced with seawater cooling, using cooling towers to minimise the seawater pumping cost. Another benefit of this concept was the ability to dispose of the cooling tower bleed stream with the existing system for neutralised red mud disposal. This would avoid the need for an additional environmental outfall from the plant. In February 2003 the Gladstone region received over 500 mm of rain, which boosted water reserves to five years supply at forecast usage rates. This led to the lifting of all water restriction. As most of the implemented water savings measures are economically viable in the absence of water restrictions, raw water usage at QAL is still less than 75 per cent of pre-2002 levels.

Jan 1, 2003

This paper examines the broader implications of recent and ongoing changes in mineral resource managementå and reporting practices and the impact that these might have on mining companies. It is likely that an International Reporting Code will be developed in the near future, based on a number of National codes produced in recent years. However, this is only part of the reporting story, as an International Code brings with it a range of further issues to resolve. For the Code to be effective, there needs to be international recognition and perhaps licensing of Competent Persons and an expanded base of sponsoring professional bodies. Also, in an increasingly global business, shareholders, regulators and other interested parties need to know and understand the general processes involved in resource and reserve estimation and reporting in order to recognise companies that maintain the highest standards. There is a current trend towards greater scrutiny of company performance in a range of areas under the banner of corporate governance, and many changes are happening that will place greater disclosure burdens on all companies in the future. Good corporate governance means management of company assets for the benefit of the stakeholders. For a mining company, there is no greater asset than its mineral resources and reserves and directors are just as responsible for effective management of their mineral resources as they are for financial good practice. The paper looks at the relevance of corporate governance principles to mineral resource management and the changes that this could bring to the way that companies deal with regulators, shareholders, financiers and others. Finally, increased scrutiny and further regulation inevitably means greater effort by the industry and higher costs. Despite this the author believes that there are substantial offsetting benefits to be gained by companies prepared to take the initiative in improving resource management practices and communicating these improvements to shareholders. In order to achieve the benefits however, the industry needs to fully engage in the changes that are taking place û setting its own standards and working with the regulators rather than sitting back and being legislated against. Mineral resource reporting provides a good model of how this process can work and there will be other opportunities in the coming years as the industry seeks to develop best practice in mineral resource management. The author is an employee of Rio Tinto but wishes to point out that the views expressed in this paper are his own and not necessarily those of Rio Tinto.

Jan 1, 2002

By Hoberg H, Schnieder FU

The disposal of residues from coal preparation and processing will to an increasing extent require investigation and consideration of the environmental problems resulting as a consequence of this. Different authors (Diingelhoff and Plankert, 1983; Hasenpatt, 1985; Szczepanska and Twardowska, 1987) have concentrated primarily on the content and the mobilisation of inorganic contaminants such as chlorides, metals and heavy metals from spoil tips, while no publications have yet been found on the question of a possible emission of organic contaminants (PCB, PAH, HC HC) from processing residues. Here the flotation residues in particular are able to bind larger quantities of organic contaminants by physi-sorptive means because of their large specific surface and, after disposal, to be re-emitt than into the environment. The flotation agents used in coal flotation are mixtures of technical distillation products with a correspondingly fluctuating composition. As Hey, 1986 showed, they may contain, in addition to the main components (n-alkanes, alcohols, surfactants), over 50 individual trace substances. In conjunction with the structural-chemical similarity of the individual components, this complicates the quantitative analysis of individual components considerably. For the analysis of hydrocarbon content of flotation products by means of extraction with organic solvents in accordance with DIN 38408, H18, the difficulty arises, besides the insufficient sensitivity at low concentrations, that geogeonic hydrocarbons are extracted from the coal as. well and the analysis results are thus falsified. These problems were overcome by the application of the 14C radiotracer method where certain components of the flotation agents are marked with radioactive carbon (14C). By measurement of the radioactivity of solid and liquid samples, the concentration of the marked substance can be measured very sensitively and precisely, whereby the accumulative measurement of similar organic substances is ruled out. Thus the reaction path of certain substances in complex reagent mixtures such as flotation agents can be traced excellently and the conceivable environment burden resulting from flotation tailings disposal can be estimated. In this paper, the adsorption behaviour of typical components of coal flotation agents are investigated for different coals and types of gangue material, the reagent content of flotation concentrates and tailings, as well as the mobility of the reagents adsorbed onto solids. The knowledge of adsorption and desorption mechanisms of unpolar hydrocarbons emulsified in water to solids are also of particular interest for the understanding of processes of organic soil contamination and for the further development of washing processes for oil-contaminated soils.

Jan 1, 1993

By P Hawkes

Within the mining industry computers have made their most significant impact with 3D design, visualisation and resource modelling/ optimisation. Recently, the application of computers to data gathering and accounting functions has also started to reap benefits. These two areas of application cover the beginning and end of the mining process. There has been limited use of computers on the middle section, the actual mining process. This is interesting when considering the relative proportion of overall mining costs that this section produces. There is a certain amount of irony in the lack of mining application software for developing accurate budgets compared to the systems/software then used to review performance against budget. Computers have been used extensively in the manufacturing industry to design, model and simulate the manufacturing process. This has not been extended to the mining process. But, we all strive to have an open pit that replicates a manufacturing plant û smooth, efficient, optimal production. If we could model mining operations with the confidence of plastic box makers we would reduce risk by an order of magnitude, improve planning and focus on value drivers. Cost û benefit analysis would be easy. The extrapolation of manufacturing to mining process models is difficult. The variables in the manufacturing process are fewer in number, have low volatility and are highly predictable. The time between a box falling on a conveyor belt and falling off is very consistent. Mining is quite the opposite. It has large numbers of variables, some of which are unpredictable and volatile. The time to fill an excavator bucket could vary by 30 per cent and the frequency distribution is unlikely to be a mathematically simple normal distribution. Further, each of these variables can be distorted by one-another û they are interrelated. The mining process is a disjointed flow of parcels whereas manufacturing is a controlled continuous feed. A loaded truck might join a ramp and follow a slow water cart up. This is the equivalent of a localised voltage drop on equipment in a manufacturing plant. The manufacturing plant is quite likely to rapidly recover to full capacity. Whereas the slow truck might throw the mining fleet cycle out of balance for hours û trucks queuing at the ROM bin and so on. A mining process simulation has been created that addresses these mining variable issues to produce a highly accurate model of the open pit mining process. The number of uses for such a model is growing rapidly as it is being utilised for a variety of projects within the industry. This paper discusses the need for and application of mining process models.

Jan 1, 2003

Mineral exploration and development can have a significant impact on the environment and local communities, in some circumstances extending well beyond the mine site. Poor environmental performance and consequent social impacts by some companies have affected the reputation of the whole industry to the extent that the principal public concern about mining is its impact on the environment. This is consistent with public attitudes about other major natural resource sectors such as forestry and commercial fishing. Traditionally the community has relied on governments to set the benchmark for acceptable environmental and social performance through establishing and revising regulations governing the mining industry. This however assumes that regulations keep pace with community expectations. It also does not take into account those circumstances where governments can have conflicting roles as both watchdog and project partner. Government regulations and industry self-regulation are not in of themselves sufficient for the minerals sector to demonstrate that it has adequately addressed environmental and social issues associated with the sector. For the minerals sector to improve its reputation it must first improve its environmental and social performance. To do this requires the sector to operate to acceptable standards of environmental and social performance and for the sector to be able to credibly communicate this to its stakeholders such as investors, non-government organisations (NGOs), customers, staff, regulators and local communities. Independent third party certification of environmental and social performance (æcertificationÆ), already operational in forest and fisheries management, is proposed as a mechanism to enable the minerals sector to achieve this. World Wide Fund for Nature (WWF) and industry partners will be collaborating in a project to ascertain the applicability of æcertificationÆ to the minerals sector. A number of economic, social and environmental benefits are identified that could accrue should mining companies be able to differentiate themselves on the basis of environmental and social performance, an attribute evident in æcertificationÆ schemes. External audiences are seeking increasing levels of information and data on environmental and social performance of mining companies, be it local communities, investors, financial institutions or NGOs. Environmental and social reporting should be a key communications device that stakeholders can rely on as a reliable, credible source of information on environmental and social performance. WWFÆs contribution to the debate about environmental and social reporting has been to develop a process to assess the quality of environmental and social reports against reporting ingredients which WWF believe are important if a report is to be an accurate reflection of the reporting entitiesÆ environmental and social performance.

Jan 1, 2002

By W J. Bruckard, M J. Vaisey

Ashton Mining Ltd (Ashton) and Lynas Corporation Ltd (Lynas) have established a joint venture partnership to develop and process rare earth oxides (REOÆs) from the Mt Weld deposit in Western Australia. The deposit is located in a deeply weathered volcanic carbonatite structure that contains approximately two million tonnes of rare earth oxides at an average grade of 20 per cent REO. As part of the 1999/2000 feasibility study currently being undertaken by Ashton and Lynas, an extensive laboratory beneficiation test program was undertaken by CSIRO Minerals on diamond drill core samples from the Mt Weld orebody. The aim was to develop a flowsheet, based primarily on flotation that could be confirmed at pilot plant scale. The target concentrate grade was 52 per cent REO with a REO recovery of at least 35 per cent. Two main ore types, nominated as CZ (limonitic siltstone) and LI (nodular limonitic ironstone) were identified for separate laboratory evaluation. The lower grade LI-type ore overlies the higher grade and more extensive CZ-type ore. The majority of the work was conducted on the CZ ore; only limited testing of the LI ore was undertaken. The latter contains a clay component that will present difficulties in processing due to its poor filtering and settling characteristics. Two processing options for treatment of CZ ore were presented for pilot plant consideration. One (Option 1) includes gravity concentration prior to flotation while the other (Option 2) includes finer grinding and four stages of open circuit cleaning. The benefits of each scheme are discussed in detail. Neither has been fully optimised and the definitive flowsheet is most likely to be a hybrid of the two schemes, incorporating the best features of each. Typical metallurgical results from each scheme were final concentrate grades of 49 per cent REO, 10-16 per cent Fe2O3 and 3.2-4.8 per cent CaO. REO recoveries were above 35 per cent in both cases. Features of the processes developed by CSIRO were the inclusion of a gravity concentration stage prior to flotation, a modified flotation reagent scheme, a change in the method of feed preparation, and incorporation of magnetic separation to upgrade final flotation concentrates. Metallurgical results obtained from flotation tests on LI ore were much poorer than those obtained for CZ ore. The best rougher/scavenger result, with the limited amount of testing so far completed, was an REO grade of 32 per cent with a recovery of 28 per cent. Further work is needed to develop a viable processing route for this ore type.

Jan 1, 2000

By S Basu, P M. Midhun

Electro-Slag Remelting (ESR) is a process capable of producing ingots with much lower centre-line segregation and better internal soundness than conventional ingot casting processes, as well as lower inclusion and sulfur concentrations. This process is commonly used for alloyed steels intended for critical applications like components of marine turbines, supercritical powerplants and rocket motor casings. It involves melting a metal electrode using electrical resistive heating in a slag pool and re-solidification of the resulting metal droplets beneath the slag layer, forming an ingot. Conventional ESR fluxes consist primarily of CaF2, Al2O3 and CaO, along with minor concentrations of SiO2, MgO etc. The emission of fluoride vapour from the molten slag causes several environmental and health problems, triggering a need to develop and reduce the fluoride content in the ESR flux. The present study aims to develop low-CaF2 alternatives to commercial ESR fluxes without compromising on productivity and the surface quality of the refined ingot. Thus, the modification in chemical composition needs to satisfy properties like electrical resistivity, viscosity and liquidus temperature, essential for efficient ESR operation. Since electrical resistivity and viscosity are highly dependent on the ionic structure of the molten slag, it is important to understand the effect of compositional modification on the structure of the flux. The present study employs Fourier-transform infrared spectroscopy (FT-IR) and Raman spectroscopy to investigate the structural variations in the modified fluxes, especially the effect of changing SiO2 concentration, in comparison with conventional CaF2-rich fluxes. Additionally, thermal analysis (Differential Thermal Analysis (DTA) and Thermogravimetric Analysis (TGA)) has been carried out to characterise the melting behaviour of the fluxes. The findings are compared with simulations carried out using the FactSage™ software, ver 8.3 (GTT Technologies, Aachen, Germany). Simultaneous analysis of liquidus temperature and the structure is expected to help in identifying the practical suitability of modified ESR flux compositions for industrial implementation.

Jun 19, 2024

By S Karosiya, A Sharma, M Jain, N N. Viswanathan, M M. Pande, D Kumar, S Kumar

Desulfurisation of steel during ladle refining is governed by both thermodynamics and kinetics. For effective desulfurisation, thermodynamically, a low partial pressure of oxygen at the steel-slag interface and highly basic slag which possess a large sulfide capacity are desired. Kinetically, the mass transfer coefficient of sulfur in the liquid steel and in the slag determines the rate of desulfurisation. A fast desulfurisation rate is achieved by maintaining sufficiently strong argon stirring of the melt. In the present work, sulfur mass balance for steel and slag was performed after the desulfurisation treatment for several industrial heats. The decrease in the sulfur quantity of the liquid steel was more than the increase in the sulfur quantity of the slag. The discrepancy in the sulfur mass balance suggests that the sulfur could be transferred to: (a) the gas (via slag) phase; or to (b) the refractory (crucible) phase. The preliminary investigation of the refractory samples taken at slag-refractory and steel-refractory interface showed no interaction of sulfur with the refractory. Therefore, the possibility of sulfur transfer to the gas phase was verified by carrying out melting experiments of sulfur containing slag in an argon/air atmosphere. Sulfur containing slag was initially melted in an MgO-C crucible under an argon atmosphere followed by creating the air atmosphere just above the melt. Careful sampling and analysis from the cold spots of the crucible, much above the melt surface, revealed formation of a fibrous structure. Scanning electron microscopy energy dispersive X-ray spectroscopy (SEM-EDS) analysis of these fibrous deposits confirmed the presence of oxides and sulfides. Oxidation of sulfur containing slag under air atmosphere was also performed using a thermogravimetric analysis (TGA) set-up. It showed a constant sulfur loss in the range of 1300– 1500°C. Thermodynamic calculations carried out using FactSage™ ver 8.3 for these experimental conditions are in good agreement with the observed results.

Aug 21, 2024

By S H. Li, H Z. Gu, A Huang

High aluminium steel is a promising advanced steel known for its exception properties and holds significant economic and strategic importance. However, the CaO-Al2O3-SiO2 based slag with high alumina content reacts vigorously with alumina refractories during the smelting process at high temperature, seriously affecting the safe and efficient production of furnaces and resulting in the formation of Al2O3-MgO non-metallic inclusions within the molten steel. This is a bottleneck problem for high-quality steel refining, and the key reaction path during the corrosion remains unclear. The dissolution reaction mechanism of alumina refractories in high alumina CaO-Al2O3-SiO2 slags under a weak static magnetic field was investigated in this work, using high temperature laser confocal microscopy and in situ radiation spectroscopy techniques. The results indicate that the interaction between the high alumina slags and the alumina refractories is governed by free radical reactions. The dissolution of alumina forms AlO and AlO2 radicals. The reaction rate increases with the C/S ratio of the slag due to its low polymerisation. The reaction between non-bridging oxygen and AlO2 free radicals accelerates the generation of AlO and O2ꞏ- radicals. The reaction layer composed of calcium aluminate is formed through the recombination of AlO, Caꞏ+ and O2ꞏ- radicals. The weak static magnetic field induces the Zeeman splitting of free radical pairs and intersystem crossing occurs, promoting the formation of triplet free radical pairs through the hyper-fine coupling effect. The reaction can be significantly inhibited as the triplet free radical pair does not meet Pauli’s incompatibility principle. This discovery perfects the structure theory of molten slags with radicals and provides supplement to the design of the highly slag-resistant refractories, and provides the theoretical basis for the development of external field protection technologies for high-quality steel refining.

Jun 19, 2024

By R G Warren

Most orebodies have cross-sections of less than 1 km2 and hence do not offer a particularly large target for exploration. Fortunately, although in the geological record ore deposits are small and rare and result from the exceptional coincidence of certain geological processes, these processes are mappable on a much larger, district to regional scale and constitute a mineral system in which the ore deposit is the central feature. A mineral system can therefore be defined as `all geological factors that control the generation and preservation of mineral deposits, and stress the processes that are involved in mobilising ore components from a source, transporting and accumulating them in more concentrated fonn and then preserving them throughout the subsequent geological history'. The mineral system concept emphasises that for many ore deposit types, although economically viable mineralisation may only occur on a scale of say, hundreds of metres, the total system of fluid-rock interactions that led to ore formation can extend over a distance of tens to hundreds of kilometres around the deposit. When mapped out, the total mineral system provides a far larger exploration target than the actual ore deposit itself. Important geological factors defining the characteristics of any mineralising system include: 1. sources of the mineralising fluids and transporting ligands; 2. sources of the metals and other ore components; 3. migration pathway; 4. thermal gradient; 5. energy source; 6. a mechanical and structural focusing mechanism at the trap site; 7. chemical and/or physical traps for ore precipitation. Many of these factors individually are common throughout time and space and are mappable on a regional scale. The delineation and empirical prediction of mineral systems can thus be approached by combining two components of metallogenic research. Firstly, the development of maps of regional geoscientific data and data sets of the distribution of factors significant for mineral systems in general. Secondly, the determination of the essential ingredients of particular styles or types of deposits in terms of mappable elements that any exploration program could focus on.

Jan 1, 1994

By Broome A

In a technologically oriented industry, it is important to understand and apply technology very consciously to create competitive advantage. Technology is not an activity which is simply restricted to CSIRO or the research and technology department. Technology improvement is a part of everyone's role. It is a way of life - the technology facet of continuous improvement. For this reason, The AusIMM has organised this Travelling Technology Forum - a series of presentations about automation in mining. To make the message more accessible, The AusIMM had originally planned to take the Forum to four regional mining centres: Mackay/Townsville, Singleton, Burnie and Kalgoorlie, but only one seminar was held, ie at Singleton in March 1997. Seminars at other locations were cancelled because of insufficient registrants. The presentation by Andrew Logan of BHP Cannington was not available for the Singleton forum. The aims of the forum were: ò to heighten awareness of the key technologies and their impact in the minerals industry in the medium term; ò to foster creative thinking; ò to encourage people to broaden their technical and commercial skills and develop individual networks and linkages based on an interest in these key technologies; ò to share information on the application of these technologies in the industry; ò to promote an enhanced appreciation of the need for an innovative culture; and ò to encourage staff to consider post graduate courses in technology management. The AusIMM wanted to not only raise awareness about `automation in mining' issues, but also to get technology in a more general sense back onto `centre stage'. The Forum was generously supported by CSIRO, Western Mining Corporation Ltd, BHP Coal Ltd, Aberfoyle Limited, Goldfields Ltd, Novacoal Australia Pty Ltd, Pasminco Ltd, and RGC Limited. The program was endorsed by the Centre for Mining Technology and Equipment (CMTE). Copies of the full papers are available from the authors, see `References'.

Jan 1, 1997