Search Documents

In preparation of this Paper, the emphasis has been laid on the commercial rather than on the technical and scientific aspects of coal evaluation. It is intended to describe and comment on the principal factors which currently determine the selection and procurement of coking coal for the steel industry, and is not based on the results of any original research by the author. Evaluation of different coals for strictly thermal uses, for gas production or other chemical applications has not been attempted, and comparisons of coal with other fuels have been excluded: the paper is concerned only with coals for the production of blast furnace coke. The discussion is strongly related to, and illustrated by, British, and to some extent, other Western European practice, but it is hoped that the general conclusions may have a wider application.

Jan 1, 1975

By Q Qian, M Karakus, J Wang, N Melkoumian, D Goodchild, Q Sui, C Wang

Probabilistic analysis is widely used in slope stability assessment because of its capability to take into account uncertainties associated with geotechnical parameters. There are, however, still many unresolved practical issues to the application of the method. One of these issues is the integration of assessments when multiple sets of fractures are considered for the entire slope. In the present study, this issue is addressed within the framework of Monte Carlo simulation. Probability of failure for pairs of fracture sets are assessed independently and the final assessment of the probability of failure for the entire slope is done using conditional probabilities. Prominent Hill open pit, in particular, the problematic fresh Bulldog shale formation, was used as a case study to test the method proposed. The SWEDGE program of the RocScience software package was used for the analysis.

Sep 26, 2011

By Schoning W. L

Ore deposit models form the basis for numerous other economic decisions in the mining process. The success of these economic decisions therefore depend directly on the accuracy of the ore evaluation process. The Geology Department at the Sishen Iron Ore Mine is responsible for the generation of a reliable geological computer model of the rock material with predicted grades. This information is then utilised for further ore reserve calculations, mine planning, production scheduling and grade control. Owing to a very complex geological orebody, grades and beneficiation characteristics differ significantly from sample to sample. This means that ore evaluation is a difficult process and great reliance is placed on computer techniques. In 1993, preparation for the ISO 9002 quality certification of the mine motivated the Geology Department to hold formal `problem solving' sessions in order to identify and revise problem areas in operating

Jan 1, 1995

By Chapman G. J

Mining operations require detailed and precise methods and procedures for the optimum selection of ore from waste. A fundamental procedure applied to achieve this selection is accurate sampling. The key parameter to accurate sampling is an understanding of the degree of heterogeneity of the key element contained within a sampling mass. This paper will describe the methods applied for the calculation of the fundamental sampling error and the techniques used to achieve a representative sample in the Fimiston Open Pit, Kalgoorlie.The utilisation of Pierre Gy's sampling theory has optimised the blast hole sample quality and quantity for submission to the assay laboratory. This has resulted in reduced cost and optimised assay reliability in statistical terms. Similarly the analysis of exploration drill holes for resource definition has optimised drilling procedures in terms of the drilling method, sample length and sample quantity.

Jan 1, 1993

The B.H.P Company has been using shortwall mining methods for the past six years in the Southern Field. several aspects this experience shortwall equipm H.P. Company has been using shortwall mining methods for the past Northern Collieries and for several years at Corrimal in the Various papers have described and assessed that work. There are of recent work which supplement prior publications. The summary of to date is a background to discussion of the role of self-advancing ent in support in pillar extraction.

Jan 1, 1974

By S R. Hencher

The development and availability of modern software for cavern design over recent years has provided design engineers with a range of usable design tools. The paper discusses the range of modern software available, presents a design methodology, reviews ground investigation requirements and software available for data processing and management, and discusses requirements and common analytical considerations with reference to typical packages. Caution is given of the tendency for readily available and user friendly software to be used without a full appreciation of the underlying engineering principles.

Jan 1, 1999

A method is proposed for the determination of antimony in ores. Antimony is volatilized as antimony iodide by heating with ammonium iodide at a controlled temperature.The fusion mixture is extracted with hydrochloric acid and the antimony content is measured by atomic absorption spectrophotometry using an air/ acetylene flame. The time taken for analysis when comparedwith existing fusion and separation procedures is considerably reduced. Cations and anions likely to be present in antimony ores were also studied for possible interference effects but were not found to interfere.

Jan 1, 1972

A resume covering currently accepted views on blasting vibration measurement, human response, and criteria for damage is presented as background information for readers who are not conversant with blasting vibrations. This is followed by sections on vibration level estimation and blasting techniques to control vibration. Emphasis is placed on making use of the scatter in the delay intervals of half-second delay detonators, the use of smaller explosive charges for early delay numbers, and the non- use of zero-delay (instantaneous) detonators in cer`a. n cases.

Jan 1, 1976

Factors influencing Cost, systems available for transporting minerals, particularly on land, and methods used for comparing costs are reviewed. A case study presents comparative costs graphically for coal haulage, assumed in Queensland, by 31-6" gauge rail, belt conveyor, 120 ton road train, slurry pipeline, and transmission of electrical energy by transmission line. The effect on comparative results of alternative methods of including initial capital and capital replacement costs is considered and approximate break-even points between systems, bearing in mind the assumptions taken, are discussed.

Jan 1, 1973

By G P. J Dijkema, M A. Reuter

From a material cycles perspective all processes are interconnected and consequently a process can never be evaluated as an isolated and independent unit. This also holds true for the evaluated co-incineration options. Environmental and sustainability issues for example, such as raw material and energy utilisation or air pollution, are a resultant of the whole system of industrial activities. It is therefore important, not to optimise a single process or industrial activity, but rather the whole system. Although engineering procedures for the design of individual industrial units are well developed, the problem of determining the best arrangement of these interconnected units is often far more difficult. Regulation that manages the arrangement of the units for waste processing is still under construction. In the evaluation of co-incineration, analogous principle from process control can be used: feedforward control. This principle includes the determination of which outlets can be used for all process outputs, hence avoidance of any æunusableÆ products or wastes possibly arising from co-incineration. To establish the extent, to which produced wastes are usable, a system overview is necessary, in addition to in-depth information on the subsystems, which produce and can consume wastes. Material cycles modelling can be used as the basis for a tool that supports the development of a suitable playing field. It should provide overview of the system and in-depth information on its subsystems. This tool then represents an attempt to bridge the gap between æholisticÆ industrial ecology and process engineering.

Jan 1, 2000

By K Guilfoyle, A Robertson

In the mid-1970s, trucking ore from 400 m depth to the surface was perceived to be the practical and economic limit for metalliferous underground mines. Improvements in truck design and decline development resulted in the economic depth of haul exceeding 600 m by the mid-1990s. Today, mine operators and contractors are planning to use trucks for ore haulage from depths in excess of 1000 m. The authors of this paper estimate that there are in excess of 300 diesel-powered trucks operating in mines in Australia, and that by the year 2005 more than five per cent of these trucks will be æroad trainsÆ (ie trucks towing powered trailers or truck-trailer combinations). This paper examines the road train concept, presents cost and performance data and describes the advantages and disadvantages of the road train system as well as proposing the types of applications for use of road trains in Australian metalliferous underground mines. Truck performance is based on payload and average speed (expressed as tonnes x kilometres per engine hour (t km/h)). A road train with a powered trailer has a large payload capacity and two engines to provide a high ratio of power to gross weight. Thus it is possible to exceed 300 t km/h per cycle for an average haulage gradient of 1:9 compared to 250 t km/h for conventional articulated dump trucks (ADTs). It is likely that road trains in excess of 100 t capacity will have application for level ore haulage at large mines in Australia.

Jan 1, 2002

By C J. Corbett

Many underground mining methods rely on blasted rock moving under gravity to report to extraction points. Mining of orebodies dipping between 20 - 45 degrees poses a unique challenge for mining engineers in that a dip angle in this range will not allow the movement of broken ore down the footwall to the mucking horizon utilising gravity. This is more so in cases where the natural angle of repose of the rock is less than the dip of the orebody. Hence, innovative mining systems are necessary to mine this type of orebodies. In Australia, the method of uphole retreat panel stoping is commonly used to extract orebodies in the dip range of 20 - 45 degrees and thickness range of 5 - 15 m. In the Zambian Copperbelt a method called continuous retreat updip stoping is used for orebodies with similar dips and thicknesses. The mechanised form of this mining method has potential for application in the metalliferous mining industry in Australia. In this study a comparison is made between mechanised updip (MUDS) and transverse retreat stoping (TRS) methods. A hypothetical nickel sulphide orebody located in Western Australia is used as case study. The net present value for mechanised updip stoping is seven per cent higher than that of transverse retreat stoping based on the assumptions applied. Initial results of this study indicate that mechanised updip stoping can be adopted for Australian mining conditions. However, lack of significant local experience with the method is often cited as a reason for not adopting it even in situations where it is clearly the best option.

Jan 1, 2003

By Y A. Stepanyants, J Crawford

A practical field method for determining the maximum value of the intrinsic oxidation rate, Smax , of sulfidic materials in waste rock dumps is proposed. Knowledge of the intrinsic oxidation rate of sulfidic materials distributed in a dump is necessary for predictive modelling of oxidation and pollutant generation over time. The suggested method uses the fact that drilling waste rock dumps to install probes for monitoring temperature and oxygen concentration causes large volumes of air to be injected into a dump by the drill rig. By measuring the rate of decrease of oxygen concentration along the length of a borehole immediately after installation, it is proposed that Smax can be calculated at different depths. The aims of this work were: to derive a simple, practical formula for the estimation of Smax from the oxygen concentrations measured over time, based on some simplifying assumptions; to use a two-dimensional numerical model that incorporates all the necessary physical processes to model the behaviour of an aerated dump over time for a reasonable range of dump and material parameters; and to compare the results of the two approaches to assess the validity of the simple formula as a method for estimating Smax. It has been found that the technique can provide reliable estimates of Smax when the value is of the order of 10-7 kg(O2) m-3 s-1 or greater. At the lower end of the range however the radius of the zone aerated during drilling becomes an important parameter and further work has been recommended to investigate this aspect of the method.

Jan 1, 2003

By Saint-Smith J. C

The anode, tank house and wire bar plant and operations are described with particular reference to those features of design and methods which are characteristic of this refinery at its inception.Reference is also made to auxiliary equipment, transport and materials handling facilities.The work of commissioning the plant late in 1959 is discussed and comment is made on the organisation of construction and origin of the equipment.LOCATION OF PLANTThe site chosen for the copper refinery is on level ground adjacent to the junction of the Mount Isa and the main north-south railway lines at Stuart near Townsville, Queensland. Blister for refining is received by rail from Mount Isa. Refined products are taken 10 miles by road to Townsville Harbour for shipment to other Australian ports or overseas, or despatched by rail direct from the plant.Adequate room for expansion was provided to cover copper refining and any associated industry. The layout of future extensions was planned and space reserved for them before detailing the original units of the main refinery.The initial plant also provides convenient storage facilities and is laid out to derive the greatest benefit from prevailing northerly breezes during the humid tropical summer.As far as possible, the working areas are located so that the prevailing winds cool them as they traverse the buildings.These factors are of very great importance since this is believed to be the only copper refinery in the tropics operating with all white labour and in any case the Company set out to provide the best possible conditions for its operating personnel.

Jan 1, 1961

Chromite ores have a long history of low pricing and for AustraliaÆs only chromite mine this has been a particularly tough challenge, especially as the mine is located nearly 400 km from the nearest port at Port Hedland. A stockpile of chromite fines (-16 mm) has been built up since 2003. The opportunity to develop a facility to treat this material to produce a chip (-16 + 1 mm) product and a sands (-1 mm + 45 micron) product was taken when the price increased to above US$140/t. A simple add-on plant containing a heavy media cyclone circuit for the chips and a spiral circuit for the sands was designed and developed. During construction of the fines plant the price of chromite reached a level where the payback for the entire project was less than eight weeks. Soon afterwards the price and the demand for chromite plummeted and the site was put on care and maintenance, except for the commissioning of the fines plant. This put considerable pressure on whether to continue to operate the plant or to place it in care and maintenance. Times of boom and bust provide management with almost totally opposite views. By not taking a conservative view on prices and costs, the effect of extremely low prices and minimal demand can be devastating to a good project. Designing and building plants with conservative costings in boom times gives a greater chance of keeping projects alive during the bust periods that tend to follow.

Jan 1, 2009

Samples of the feed, underflow and overflow mediums from dense medium cyclones operating at low separation densities in eight commercial coal washeries were sized and analysed, to obtain comparative cyclone classification performance curves for the magnetite, shale and coal components in the circulating medium. The resulting component classification curves indicated that the dense medium cyclones hydraulically classify the magnetite and the shale to the underflow with a Stokesian size and density relationship at these low medium densities, ie the shale curve was shifted parallel to and appropriately coarser than the magnetite curve because of the lower density of the shale. However the lower density coal reverse classified to the overflow (ie away from the cyclone wall) with a similar Stokesian relationship. By correcting the magnetite and shale classification curves for the bypass inefficiency to underflow, and similarly correcting the coal classification curves for the bypass inefficiency to overflow, the corrected classification curves for the magnetite, shale and coal were reasonably parallel (considering that the coal has a range of densities). Using a value of five for the density of the magnetite, the displacement of the shale and coal curves corresponded to densities of 2.27 and 1.38 respectively for one circuit, although the data was not as good for the other circuits. This reverse classification mechanism was confirmed in a 140 mm diameter laboratory dense medium cyclone circuit using low density (1.20 - 1.30 RD) tracers, sized from 0.25 to 2 mm. These classification performance curves were corrected for bypass ineffiency (as above). The corrected curves were parallel and displaced according to tracer density, even though the lowest density tracers were reverse classified to the overflow. The data indicate that the rates of classification of all particles could be described by the same Stokesian relationship, regardless of the direction of travel, except for a narrow band at the partition density. Particles heavier than the partition density classified to the underflow, particles lighter than the partition density reverse classified to the overflow and particles identical to the partition density were not classified at all. Consequently it should be possible to simulate partition in dense medium cyclones, operating under free settling low density conditions, with a simple cyclone classification model, provided the partition density can be accurately calculated from, or correlated with the cyclone feed, underflow or overflow pulp densities. The tracer partition performance in the laboratory cyclone was an inverse function of the tracer particle size, as proposed by King and Juckes (1984) for medium/coal ratio in low density medium systems. Their sized coal data was parallel, with lower partition values due to a higher energy cyclone. Partition data with similarly sized tracers (Scott, 1988) showed a parallel shift to higher partition values due to the separate effects of higher viscosity medium and a larger diameter lower energy Cyclone.

Jan 1, 1993

Interactive data exploration is essential for visualising grade distribution and geological controls on orbodies. Quick and appropriate computer techniques for making daily 'value adding' decisions include routine imaging of numerical data suc

Jan 1, 1998

The current drill-and-blast method of tunnelling is cyclic and, for this reason above all others, has a future application potential which is lower than that of continuous methods. There is scope for progress in several facets of today's drill-and-blast tunnelling. But even if each of its unit operations and the synthesis of these were to be optimised, this conventional method will, in the long term, fail to be a serious competitor for tunnelboring machines (TBMs), roadheaders and the like. If its role in tunnelling is not to decline at an increasing rate, drill-and-blast will need to be transformed into a continuous system. Boring and cutting machines consume considerable energy (and expenditure) in creating rock fragments which are smaller than those required by muck-handling equipment. In this respect, blasting is more efficient. Mechanical methods are also less versatile and flexible and, when planning proceeds on a basis of meagre or inadequate geological data, cannot be costed as accurately. Currently, research gains for TBMs and roadheaders are greater than those for conventional tunnelling. If (as is likely) the disadvantages of mechanical methods continue to be reduced at a greater rate, the swing away from drilling and blasting will gain momentum.

Jan 1, 1987

By D Yuen, J A. D Connolly, T V. Gerya

Recent works suggest that dehydration of subducting slab and consequent hydration and partial melting influences the dynamics of mantle wedge. Plums originating form the subducting slab due to Rayleigh-Taylor instability are responsible for heterogeneous composition of the mantle wedge. Also, occurrence of partial melt in the mantle wedge can trigger dynamic processes like exhumation of UHP rocks in intra-oceanic settings or can influence characteristics of the subduction tectonic regime. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Sun Yubo

A basic method for designing reasonable jig cycles for movable-screen jigs is presented in this paper. The reliability and effectiveness of the designed jig cycle was verified with tests performed on an artificial mixed material. An iron ore (12 - 100 mm) from Huashugo Iron Mine, Jiuquan Iron and Steel Company, was treated in the TJD-75 movable-screen jig using the designed jig cycle. A good result was achieved. The procedure presented here should provide a reliable technique for the design of a commercial movable-screen jig.

Jan 1, 1993