Search Documents

By Childs G, Ritchie IC

This paper describes the principle and operation of small hydrocyclones for use in the coal, minerals and other process industries. The principles for selecting a hydrocyclone for an application are also discussed. Typic- al uses and installations in various industries are described.

Jan 1, 1984

By Mishra BK, Agrawala S

The traditional method of scale-up uses the population-balance model. In particular, the selection function values for a material are determined in a laboratory mill and a variety of correlations are used to scale these values to plant scale mills. For example, the factor D2-5L (D-mill diameter, L-mill length) appears in many power correlations. The number of collisions is proportional to the number of balls (aD2L), the frequency of mill rotation ((x 1/4D-) and effectiveness of impact ((XD), which gives rise to the 'D2.5L' expression. However, what is lacking in this expression is that it does not throw light on the intensities of collisions. In other words, the collision intensities in both laboratory and plant scale mills are implied to be identical. This fact has been very limiting. Alternatively, the collision frequencies and intensity of impacts can be computed with the discrete element code. This code computes the motion and collision of each individual ball in the ball charge. Therefore the number of collisions and the fraction of collisions in the energy range Et, E2.òòE. (collision energy density) are calculated for a given mill size and operating conditions. Then, using the breakage function determined in drop-weight experiments, the evolution of size distribution is computed for a lab mill. The collision frequency and energy density for larger mill sizes are shown. The fundamental theory outlined for the calculation of size distribution is equally applicable for the large mill, which is the basis for scale-up.

Jan 1, 1993

By P Bethune

Back Creek is a tributary of the Condamine River. It flows in a northerly direction across the existing Commodore coal reserves. The diversion of Back Creek was proposed to minimise sterilisation of the reserves. The approval process required a Waterworks Licence application, under the Water Resources Act 1989 (Qld), for the construction of a stream diversion channel and floodway. The diversion was designed using the æreference reachÆ approach, which mimicked existing properties of Back Creek. The following design standards were developed for the diversion: the diversion corridor width was 500 m; the diversion geometry was specified for both the low-flow channel, and the floodplain; material properties were specified for both the low-flow channel lining and the diversion bund; compaction standards for both the low-flow channel and floodplain were set; and the diversion rehabilitation included a riparian corridor and pasture land with clumps of native trees and shrubs. The following performance criteria were developed for the diversion: velocity regimes were replicated for the design events considered, in an attempt to avoid increasing the diversion flow velocities in comparison with the existing creek flow velocities; sediment transport calculations indicated that no significant change in sediment transport was expected within the diversion; overburden settlement estimates for the spoil placed in the corridor were summarised, and will be monitored throughout the construction process; geotechnical stability of the proposed Eastern Pit Buttress and the diversion bund configurations was confirmed; and groundwater impacts were assessed. Construction techniques, monitoring and further investigations are also discussed in this paper.

Jan 1, 2003

Bacterial leaching of sulfide minerals are fairly well established in heap, dump and in situ leaching and the primary bacterial treatment of refractory gold concentrate using CSTR have gained industrial prominence in recent years. Three cultures, a mesophile T ferrooxidans (DSM583), a moderate thermophile Sulfobacillus acidophilus (strain YTF1) and a extreme thermophile (Sulfolobus strain BC65) were used for the biooxidation (pre-treatment) of the Porgera gold-bearing pyrite concentrate under optimum O2 and CO2 enriched air (30 per cent O2 and ten per cent CO2) based on volume ratios. The positive effect of using oxygen and carbon dioxide enriched air for the biooxidation of gold-bearing pyrite mineral was clearly demonstrated where an increase in Fe release rate by a factor of 2.8, 1.8 and 1.5 for DSM583, YTF1 and Sulfolobus respectively were observed compared with the shake flask tests. The lag phase observed with the other test conditions such as in shake flask or with air decreased by about 80 per cent for all three cultures. The average observed dissolved oxygen concentrations in the pulp for these tests were 8.7, 5.8 and 5.0 mg/L for DSM583, YTF1 and Sulfolobus respectively, indicating that O2 was not limiting in these tests. The pulp redox potential was observed to increase with time for all tests coincident with the leaching rate and reaching a maximum of 663 mV, however the maximum value differs for each strain, with DSM583 exhibiting the highest followed by YTF1 and Sulfolobus. Biooxidation of pyrite under optimum gas enrichment at different pulp densities showed near total Iron extraction occurred for pulp densities of three, ten and 20 per cent (w/v). At high pulp densities, more so at 40 per cent than 30 per cent (w/v), the leaching rate decreased rapidly for tests with YTF1 and Sulfolobus. Monitoring of dissolved O2 shows that O2 demand increased with increasing pulp density and the average dissolved O2 concentration observed for YTF1 and Sulfolobus at 40 per cent solids concentration was 1.0 mg/L and below, suggesting limiting oxygen and carbon dioxide conditions for these two cultures. The decrease in leaching rate observed at high pulp densities (30 and 40 per cent) under optimum gas enrichment was accompanied by low metal dissolution and low redox potential values which was attributed to shear stress due to attrition of cells by high solids concentration, toxicity of metal ions especially Ag and Fe and the formation of precipitates and jarosites as confirmed from XRD analysis of leach residues hence impeding the leaching process. Limiting conditions due to high pulp density and viscosity were only observed for YTF1 and Sulfolobus. The subsequent cyanide leaching for precious metals from the pre-treated pyrite concentrate in all cases shows the extent of gold and silver recovery increased with the degree of pyrite oxidation and Au and Ag recoveries in excess of 80 per cent were achieved compared with only 18.1 per cent and 35.9 per cent for gold and silver respectively when treated by direct cyanide leaching on the original, untreated concentrate.

Jan 1, 2004

By M Roche, W J. Huxley

Finding a balance between practical and acceptable groundwater management, and providing for the needs and impacts of mining developments remains a challenge. The changes that accompanied the recent implementation of water reforms have provided greater flexibility for the water manager and greater certainty for the resource user. However uncertainty associated with understanding of complex aquifer systems, balanced against providing for the needs of mining developments, the rights of existing water resource users and expectations of the broader community have not diminished the conflicting issues faced by water resource managers and resource developers. Licensing under the Water Act 2000 provides the regulatory link with the taking of water for water supply purposes or as a consequence of the mining activity. This paper outlines key elements of sustainable water resource management involving certainty of access to water and adaptive environmental management that are delivered through conditioning the water licences issued for the particular mining development. Implementation of this approach is illustrated through a case study involving the BHP Billiton Cannington Mine in North West Queensland.

Jan 1, 2003

By Ward S. D

When using grinding time for a batch grinding operation as a measure of the energy usefully employed for comminution; the assumptions made are often not valid. A kinetic approach, based on a study of the rate constant, or k, value for the material is more acceptable. The Rosin-Rammler distribution equation has been theoretically derived from the general equation for first-order batch grinding. This relationship, incorporating a term for k, was used in a study of the rod milling of a binary mixture of quartz and limestone.The presence and degree of interaction between the components was considered by comparing the size distribution of the mill product with that predicted by assuming the overall distribution equal to the sum ofthe distributions given by the Rosin-Rammler equations for each component weighted according to its volume fraction in the mixture. The interaction was found to be complex and particularly sensitive to particle size.A simple graphical procedure was devised to predict the size distribution of the mill. Product components and this gave a fairly good approximation to experimental data.

Jan 1, 1976

Discounted cash flow (DCF) methods are well suited and recommended as a primary valuation method for mineral assets for which there are at least indicated resources and some form of feasibility study containing engineering, production and capital and operating cost data. DCF methods are also applicable as a secondary or check valuation method for exploration properties for which no technical study has been prepared. For projects where little or no engineering, production and/or cost data is available, the process of formulating a project concept by specialists who do not possess experience and expertise in the relevant technical faculties is totally rejected as a basis for applying DCF techniques as a primary valuation method. Such an approach runs counter to The Australasian Institute of Mining and Metallurgy (AusIMM) requirement to apply relevant expertise to specific aspects of mineral valuation. Technical and commercial inputs to mineral valuation should be reviewed by specialists who have specific expertise in the relevant disciplines, and should be tempered by the quantity and quality of technical evaluation which has been undertaken and the development status of the asset.

Jan 1, 1994

By Gibson I, Somerville J

Three main confined aquifers occur in interseam sediments beneath the planned excavation for the Loy Yang Brown Coal Open Cut. Sub-artesian groundwater pressures occur in all aquifers necessitating dewatering to prevent excessive seepage and depressurisation to prevent heaving of the open cut floor and batter instability. Reduction of water pressures in coal joints is also required to maintain coal face stability. This paper describes the depressurization and dewatering strategies, investigation for and installation of pump bores and groundwater observation bores. Approximately 5000m of drilling is carried out annually for dewatering at Loy Yang and both cable tool and rotary flush drilling methods are utilized. The cabletool method is used to obtain accurate samples for laboratory analysis, whereas rotary flush methods are used for speed and for installation of the larger diameter pumping bores. A method of re-establishing pump bores after partial excavation during mine development has been successfully developed with large cost savings. Trials are also being conducted with pre-collaring of deep bores with rotary methods then sampling the aquifer strata with a cable tool rig.

Jan 1, 1988

By G R. Ballantyne, M S. Powell, M Tiang

This paper reviews the proportion of energy attributable to comminution within the Australian gold and copper mining sector. The need for this is motivated by inconsistencies in the quoted energy usage data and the lack of a common basis for reporting the fraction of energy in mining that is attributable to comminution. This study should form a reliable basis from which to assess both demand and opportunities to reduce energy consumption.The proportion of milling energy was calculated for the major producers in the Australian gold and copper sector. A sampling methodology created by Powell et al (2003 - 2010) was initially used to provide an accurate and meaningful measure of the energy used in the comminution process. However, no useful method for grouping similar mines was found. Fortunately, a surprisingly large amount of high quality data was found from a number of different sources, allowing the development of robust relationships to be used to estimate a high proportion of the unknown values. The fraction of energy attributable to comminution was found to be dependent on how the total energy consumption was defined. For instance, comminution accounted for 52 per cent of the electrical energy, but only 21 per cent of the total energy publicly reported by the mines because a substantial proportion of energy used on a mine is in the form of transportation fuel (mostly diesel). Critically, the measured electrical energy consumption does not account for transmission and generation losses, while diesel energy usage is typically quoted according to its calorific value. This review proposes that diesel should instead be converted via the mechanical efficiency factor for diesel engines. Using this conversion, comminution was found to account for 36 per cent of the available energy on average. This approach allows a useful basis of comparison for mines regardless of whether milling energy is obtained from electrical or diesel generation. A summary of the results are shown in Figure 7 with other values obtained from literature. The total comminution energy assessed in this study accounts for 1.3 per cent of AustraliaÆs electricity consumption, this figure will increase as the other mineral commodities are added to the study.CITATION:Ballantyne, G R, Powell, M S and Tiang, M, 2012. Proportion of energy attributable to comminution, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 25-30 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Turco E, Pelizza S, Castellani F, Stanganelli V

Excavation are in progress for the building of tunnels of the waterworks in West Campania (Naples). The works afferent to part II envisage tunnelling through a miocenic clay formation over consolidated by two tunnels whose sections are respectively 50 and 10m2. Tunnel blasting is carried out by mechanical means. An excavator is used in the big tunnel, whereas in the small tunnel a roadheader machine is used for a short tract and a mechanized shield is used over a long stretch. The tunnel feature complex problems regarding stability. This is particularly so for the big tunnel whose face appears unstable. For this reason the clay on the face is sistematically bolted by means of 3-metre and 12-metre bolts. This prevent the use of a TBM for tunnel Excavation.

Jan 1, 1987

Concrete has been used for many years in block caving, principally for drift and drawpoint linings. This paper describes the requirements for concrete in this application, the required properties, the mix design, and transportation and placement systems. In addition a concrete mix design rationale is also proposed.

Jan 1, 2000

By Laajalehto K

The basic condition necessary for flotation is hydrophobicity of the surface of the mineral to be floated. For sulphides, this condition usually requires treatment with a collector solution. The conditions for this treatment have until recently usually been chosen by the trial and error principle which has indeed been working relatively well under favourable conditions; ie for simple homogeneous ores. However, the present tendency to increasing use of complex and often relatively lean ores sets increasing requirements for the control of the flotation process. This development is the reason for the present rapid development of process control methods in flotation. In addition to the already well-established practices of pH and reagent feed controls, the importance of measuring and controlling the electrochemical potential of the ore particles to be floated is recognised in the case of sufficiently conductive minerals. In fact, the electrochemical potential seems to be the basic quantity determining the flotation behaviour of such relatively well-conducting minerals as sulphides. Since the hydrophobicity of the mineral and, hence, its flotation properties are ultimately determined by the composition and structure of its surface, information on these under different process conditions is important for design and operation of efficient flotation processes. The basic requirement set for the methods used for obtaining this information is high surface sensitivity of the method. The recent rapid development of surface characterisation has produced several methods which fulfil this requirement. Their application to the problem of characterising surfaces of mineral samples in contact with collector solution is, however, often complicated. The main reason for this is the vacuum environment necessary for the measurement. In the case of flotation experiments this means that in most of these methods the measurement cannot be made in situ, but the sample must be extracted from the liquid and subsequently evacuated in the vacuum chamber of the instrument. It is essential to carry out these steps so as to avoid to the extent possible changes in the sample surface. For the purpose of establishing whether this has been accomplished it is important to compare the results of methods operating in vacuum with some available in situ method. An optimal choice of methods seems therefore to be a combination of the available powerful vacuum methods with in situ measurements. The most usual combination seems to be X-ray photoelectron spectroscopy (XPS or ESCA), Fourier transform infrared spectroscopy (FTIR) and electrochemical measurements. This choice combines the unique possibilities for direct elemental and chemical characterisation offered by XPS (Cecile, 1985) with the in situ capability of FTIR and electrochemistry. In the XPS measurements, it is essential to apply a special sample handling technique to avoid loss or damage of some sensitive species of the collector-based layer on the mineral surface. In the following will be given some examples of the application of the XPS technique in combination with electrochemical methods of sample treatment to studies of the layer formed on sulphide substrates in ethyl xanthate (EX)

Jan 1, 1993

The United StatesÆ reporting standard for the mining industry for securities purposes is contained in the Security and Exchange CommissionÆs Industry Guide 7. It defines proven and probable Reserves using its own definitions, and prohibits the disclosure of quantitative estimates, for all mineralisation other than those two Reserve categories (though disclosure of Measured and Indicated Resources as quantitative mineralised material estimates is now informally allowed). Similarly, it restricts disclosure of value estimates to Reserves only, which SEC policy generally requires to be on an historic cost accounting basis. The SEC does not maintain a formal Competent or Qualified Person policy. In March 1999, the US-based Society of Mining, Metallurgy and Exploration (SME) released an update of its 1991 guidelines for definitions to be used in reporting of Mineral Resources, Reserves and Exploration Information, closely abiding by the 1997 CMMI recommendations. However, without SEC recognition, reporting under the SME and CMMI definitions is effectively barred for US companies. The SEC intends to adopt the International Financial Reporting Standards (IFRS) of the International Accounting Standards Board (IASB). This will occur within just a few years, when the convergence project for development of the IFRS has reached a satisfactory point. The US is the largest financial supporter and participator in IASB. The Extractive Industries Standard of the IFRS will likely terminate Industry Guide 7. However, the effect of this international replacement will likely be equally restrictive. This could possibly neutralise the benefit of a CMMI-based global reporting standard. SME, the US society encompassing the widest range of mining industry professionals, does not have a Code of Ethics. It has no mechanism for requiring members to abide by a professional standard. SME is presently looking into possible solutions for this deficiency. US-based professional societies that do have a binding Code of Ethics, generally cater to a single profession, and are not just mining industry related. The American Institute of Professional Geologists (AIPG) and the American Institute of Minerals Appraisers (AIMA) are examples. The SME is considering creating a subsidiary body with an enforceable Code of Ethics. To support a CMMI-based global reporting standard, competent persons will need to work across international borders. A standardised mechanism for qualifying and registering competent persons will be needed. National rules and laws must allow competent persons to easily enter countries to perform their work. State issued licenses are increasingly required for much of the work performed in the US mining industry by engineers, geologists and minerals appraisers (valuers). Such licenses are not required by the SEC for Reserve reporting in the US, may not be required for valuation of mineral properties under certain circumstances, and except for real property valuer licenses, they generally do not have a binding code of conduct. However, state licensing of professionals forms a substantial and increasing barrier to interstate trade in professional services, and can be a prohibitive barrier to professionals from outside the US. Any rationalisation of this confusing patchwork of regulations confronting US minerals industry practitioners will only occur as part of larger, national change, hopefully aimed at compliance with international standards and protocols. The US does not have a valuation standard aimed specifically at the mining industry. The Uniform Standards of Professional Appraisal Practice, the national valuation standards, often must be applied to mineral property valuation, but contains no specific instructions for minerals. The author has campaigned against development of minerals valuation standards proposed by US minerals institutes. Instead he encourages the mining industry worldwide to place its support behind the initiative of the International Valuation Standards Committee (IVSC) to include an extractive industries section in its International Valuation Standards (IVS). This should provide a global set of valuation standards for the mining and petroleum industry within two years. This addition to IVS will provide essential valuation standards reference support for the extractive industries financial reporting standard of the International Accounting Standards Board. The IVS has achieved a high level of acceptance in the developed and lesser developed countries of the world. It provides a comprehensive framework of Generally Accepted Valuation Principles for the valuation profession internationally, for valuation of all property or asset types. IVSC is effectively a sister organisation to IASB. The IASBÆs International Financial Reporting Standards (IFRS), previously known as the International Accounting Standards (IAS), reference and quote IVS in some instructions for determination of fair value. IVSC is a non-governmental organisation (NGO) member of the United Nations and maintains liaison with many important international economic, accounting and financial agencies, such as the OECD, IMF and WTO.

Jan 1, 2002

By Roberts C

The satisfactory testing and characterisation of mineralisation amenable to heap leaching, is of prime importance to successful operation of a project. This paper outlines a methodology for assessing material suitability. A general model is used for classing material types for suitability for treatment and for economic analysis. The four levels of these are overburden, oxide, transitional and unoxidised materials. During exploration, reverse circulation (RC) drilling can be used effectively to define these zones by a combination of logging, analysis and provision of cuttings for column leach and bottle roll trials. RC cuttings can he used effectively for column leach trials, when calibrated against conventional processing-sized samples, obtained from surface. Tbis allows metallurgical testing to depth and definition of transitional ore types and the base of oxidation, accurately and economically with an acceptable density of samples. The accurate prediction of base of oxidation and variations in recovery with depth and ore types can be used to develop 'economic' pit designs with zones of variable recovery. Petrological studies of leaching results and examination of mineralisation types carried out on concentrates, provide information on gold distribution and physical and chemical constraints. The examination of concentrates can be particularly useful for types of mineralisation when overall gold content is frequently at or below one pan per million. Explanation of anomalous recovery of gold grains in dense goethite and solution-robbing by carbonaceous material can be identified by use of petrological and scanning electron microscope. An understanding of the role of the host rock in leaching characteristics can also he provided by petrology where siliceous or clayey materials can require significantly different treatment.

Jan 1, 1994

The mining industry worldwide relies upon the identification of resources that can be economically developed and operated. Access to land is paramount through all stages of the exploration, development, operation and rehabilitation stages. Clear rights to use of land for the purposes of mining must be available and protected throughout the life of the project. Stable and enduring criteria for mining of the resource, once identified, are required to attract exploration and development expenditure. The purpose of this paper is to investigate the varying approaches to granting access to land for use for exploration and mining development, including the processes by which a project is approved by community and government and the time scale for such approval. The paper concentrates on the legal issues arising throughout this process. The law is stated as at September 1997.

Jan 1, 1997

Ion exchange resins are an attractive alternative to activated carbon in both column and resin-in-pulp processes for the recovery of gold from cyanide solution. Resins are widely used for this purpose in the Soviet Union apparently in preference to activated carbons.A wide range of resins are available and the high level of resin technology is demon-strated in the resin processes used to recover uranium.The anionic gold complex, Au(CN) 2 , is selectively adsorbed onto weak and strong base resins. However other anionic cyanide complexes, cyanide ions and other anions from the process water are also adsorbed onto resin sites. Resin selectively for gold is not as high as it is for activated carbons. As a result similar gold loading capacities are obtained for resins and carbons when used in plant liquors.

Jan 1, 1984

By Cousens DR, Benhamou M, French DH

Techniques appropriate to petrographic image analysis are being developed using digitized backscatter electron images of well characterized mineral assemblages obtained from a Cameca scanning electron microprobe. Emphasis is on developing descriptors for size, shape and association of mineral grains as these all convey important information concerning the nature of rocks and the processes that have operated upon them. Processes, for example, that could indicate the proximity of mineralization. For convenience, the work is being carried out on the PDP11/73 host computer of the electron micropt be, although it is recongnized that such a multi-user environment is not appropriate for practical image analysis. The eventual aim is to develop a low-cost microcomputer-based package for quantitative description of mineral textures and rock fabrics as an objective aid to the petrographic analysis of ores and host rocks.

Jan 1, 1989

The Japanese Government promulgated the æLaw Concerning Special Measures Against DioxinsÆ on 16 July 1999 and it was enforced on 15 January 2000. This is a unique law specialised to protect the environment by the control of dioxin emissions from waste incinerators and several industrial processes. In this law, a few metallurgical processes other than waste incinerators are designated as æspecified facilitiesÆ emitting certain dioxins. Thus, emission standards for dioxins to the air were set for electric arc furnaces (EAF) for steelmaking, iron ore sintering, zinc recovery from EAF dust and aluminum recycle processes. In this paper, the inventory of dioxin emissions for Japan and the recent research and development to reduce emissions from those processes are introduced. Further, some details on the formation mechanism of dioxins and future subjects for effective control of their emissions are discussed.

Jan 1, 2002

By A Purchase, C Stacey

The procedure for operation of deluge systems installed in road tunnels is still a subject of debate. The work undertaken in this paper assists in the understanding of the effects of deluge in road tunnels, and thus aims to help inform the development of operational policy. Analysis was undertaken using computational fluid dynamics (CFD) simulations to help explore the deluge interaction with the tunnel ventilation (including smoke exhaust) and combustion products. It was found, for the scenarios considered, that: Deluge activation can decrease the required critical velocity for smoke backlayering, and this in turn can improve the effectiveness of a smoke exhaust system.The dominant parameter for deluge effectiveness is the vehicle configuration, with shielded scenarios (such as a fire in the passenger compartment) showing almost no water reaching the fire. The water delivery rate (5 mm/min versus 10 mm/min) has only a minor effect on the smoke duct damper inlet temperatures and downstream smoke temperatures for small fires (5 MW). For large fires (50 MW) the higher water delivery rate gives slightly improved performance (lower damper inlet temperatures and lower downstream smoke temperatures). A one-dimensional transient tunnel model incorporating different operational and deluge response policies (ie deluge activation times) was developed. It was used to examine the influence of different operational parameters on life safety risk and tunnel damage risk. It was found, for the scenarios considered, that: The life safety risk for different scenarios has a sensitivity to deluge activation policy with the case of delaying the deluge activation for a long time giving the worst outcomes. However, the most critical parameters for life safety risk are operator response time (for all response activities, not just deluge) and the type of fire (configuration, size and growth rate).There is a reduction in risk of tunnel damage when the deluge is activated earlier, although the fire configuration (ie whether or not the seat of the fire can be reached) has the greatest influence on the outcome. It is concluded that the deluge activation policy should be case-dependent. It will depend on the tunnel, the safety systems provided, and most particularly the vehicles involved. The current policy in Australian tunnels is for manual activation of the deluge by the tunnel operator as soon as practical after the fire is confirmed (see also PIARC, 2007). This is a good policy. However, future work may be helpful to improve the skills of operators to make the best judgement as to when deluge should be activated, balancing all risks. This work could include research to further the understanding of deluge and fire in road tunnels, training programs and consideration of historical fire events.

Jan 1, 2008

By K Whelan

The Land Access Branch of the Mines Division of the Northern Territory Department of Mines and Energy is responsible for Aboriginal Liaison and cross-cultural matters that affect the Department. In essence, it exists to provide a basis for communication between the Department, industry. Aboriginal organisations and Traditional Owners. The paper outlines the various ways in which this is accomplished including the preparation of detriment submissions for pending land claim hearings, the use of promotional material to support access to Aboriginal Land for NTGS Mapping Programs and field work, and advice/assistance on exploration and mining issues.

Jan 1, 1994