Search Documents

By C E. Gawith

The Waihi underground mining operation currently mines epithermal veins ranging from two metres up to ten metres in width using a ‘Modified Avoca’ stoping method. This method consists of longhole bench stope mining at 15m to 18m sublevel spacing. The bulk of production drilling and blasting is top down with the extraction length of a typical stope panel nominally being 18m to 20m along strike. A stope panel is usually taken in two blasting cycles followed by the remote bogging of the stope ore. The panel is backfilled in-cycle using unconsolidated waste rock material which is tipped into the void from the upper level using a Caterpillar R2900 or R1700 sized underground loader. The underground mine first commenced production in 2008 and up until 2016, as was typical of many open stope mining operations at the time, an underground loader was used to place a waste rock bund at the top brow of the open stope. This rock bund was the principal means of protecting people and equipment from this hazard. In 2016 there was a fatality at the mine when a loader that had been tasked with building this rock bund fell into the stope void. Immediately post incident all mining and processing operations were suspended for a week to allow colleagues to grieve, to observe cultural protocols and to begin the investigation into this event. During this period senior operators, supervisory and technical staff developed an innovative system which used steel bollards to protect this open edge. With development over the following months this bollard system has eliminated this hazard from the Waihi underground mine.

Mar 15, 2021

Last September, when I was asked to prepare this paper, I was told the subject was "mining," a broad subject indeed! Rather than choose one of the many important technical and economic details which characterize mining today, I turned to a subject which fas- cinates me: mining's image. If we are to survive and prosper into the twenty-first century, and if industry and society are to continue enjoying the material benefits which flow from mining, we must address the melancholy fact that the general public at best does not understand mining, and at worst does not believe it is needed or deserves to continue. While my point of view is largely that of an American mining executive, I would hasten to point out that Homestake has participated in Australian mining for over three decades, and our subsidiary, Homestake Gold of Australia Limited, is now a major producer in this "lucky country." Does society need a viable minerals and metals industry? The answer is obviously "yes," so the challenge is to change some minds: not just those of the amorphous "public," but on a focussed basis targeting journalists, educators, TV commentators, politicians and opinion makers of all stripes (I thought of using "rifle shot" instead of focussed but thought that might be misconstrued). Along the way we miners must also look deeply into ourselves, our attitudes towards the society in which we function, and our willing- ness to change as well as to seek change in others. How did we become such bad guys? More than a century ago mining was not just accepted, it was even romanticised. In America, we had altered the time-honored concept of "Crown" lands into public lands made easily available to settlers pushing back the frontier. Miners even preceded the farmers and stockmen in what was perceived as nation-building, although by the 1890s there was a growing interest in conservation, especially the protection and management of forests and national parks. Even though emphasis was shifting toward government stewardship and away from trans- fer of public lands to private ownership, homesteading and mining were clearly recognised as valid uses requiring not just access, but security of tenure. Indeed, conservation as it was then understood implied management of the public domain as well as its protection. Initially this was no great problem to the U.S. mining industry, but as the nation grew and competing land uses became more important, conflicts began to appear, first over water rights and later over air quality and destructive mining practices. But these were local disputes rather than national issues, and two World Wars, the Great Depression and post-war reconstruction lulled our industry into thinking that nothing had really changed. After the storm began to break in the 1960s, the mining industry found itself confronted by a growing maze of complex and costly laws and regulations. It took us longer than it should have to realise that, in facing this challenge, we seemed to have lost the understanding and support of many of our legislators and a majority of the general public. For over 20 years now, since the first Earth Day in 1970, the U.S. Mining

Jan 1, 1991

Sheaves are a critical safety component in a winding system and are expected to survive such extreme loading events as rope break. Sheave designs have often been developed and evolved empirically, consequently many existing sheaves are not necessarily subjected to the detailed analyses that are possible using todayÆs design tools. The design philosophy for sheaves is that the rope should be the weakest link in the system so that associated equipment can function safely for any load up to rope break. A number of failure mechanisms must be considered, but buckling is often prominent. During the course of investigating the feasibility of upgrading the hoisting capacity of a winding system, the capacity of all critical components was reviewed. The sheaves in the system were found to have insufficient spoke buckling capacity for the specified rope. A proposal to increase the spoke buckling capacity by connecting spokes together using a simple tie arrangement was evaluated and found ineffective. An alternative tie arrangement concept was developed and evaluated and shown to be adequate. This paper describes the finite element model, analysis approach and results for the original sheave and the two modifications. The contribution of the sheave rim to the total buckling capacity is evaluated. Some practical issues for spoke tie modifications are discussed.

Jan 1, 2005

The tangible effects of leakage are presented graphically, and a technique for quantifying the leakage characteristics of a ventilation column using the æSolveÆ capabilities of a common spreadsheet is demonstrated. A case study of a working decline in Western Australia is used to demonstrate the potential for more realistic design of development ventilating systems, and for more cost effective management of the condition of the duct.

Jan 1, 2002

By O Dominguez

Mine value chain reconciliation (MVC) is a necessary procedure to evaluate a mine’s performance against the assumptions and models used to plan mining and processing operations. Using nomenclature from Parker (2012), F2 reconciliation is the ratio between material received at the mill, compared with material sent to the mill, commonly reported in terms of tonnes, grade and metal. Measurements of material sent to the mill can be estimated in many ways, including: fleet management system (FMS) records, truck counts, or volume reduction. Most time-based reconciliations (for example, month-end reconciliation) use short-term model depletions of in situ rock measured by periodic topographic scans or surveys.

Mar 22, 2022

The Porgera gold mine has made significant progress with the successful installation of a JK FrothCam image analysis system. The system is used to measure and control froth velocity on the scavenger circuit which has brought significant economical and operational benefits. The froth velocity signal, determined by analysis of the camera, is transmitted to the PLC that manipulates flotation cell airflow rate and cell level controllers to maintain a target froth velocity of 130 mm per second. Following on from a three-week trial installation in June 2000, a permanent installation was commissioned on the scavenger Outokumpu (OK150) tank cells. Further work is in progress on the rougher Wemco cells. This paper describes the evaluation of FrothCam Technology and its subsequent installation.

Jan 1, 2003

By J G. Shellnutt, Y Iizuka, T W-Y Hsia, T-C Liu

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The formation of magmatic oxide ore deposits hosted in chemically-evolved layered gabbroic intrusions is attributed to a variety of petrological processes, but there is little to no consensus on the general applicability of each model. Complicating the matter further is that many layered gabbroic intrusions are spatially and temporally associated with alkaline A-type granites, suggesting that there is a petrogenetic relationship between the two types of chemically different rocks. Our experimental results show that petrological modelling using a starting composition of high-Ti basalt from the Emeishan large igneous province can produce evolved silicic liquids that resemble the compositions of microgranular enclaves from the syenitic unit of the bimodal, oxide ore-bearing Baima igneous complex. The experimental results confirm that bimodal gabbro-granitoid complexes can form from a common parental magma and that early crystallisation of Ti-rich magnetite can explain the formation of the oxide ore deposits in the lower parts of the layered gabbroic intrusions. We conclude that crystallisation of a typical high-Ti basaltic parental magma can produce world-class giant magmatic oxide ore deposits and that the occurrence of some alkaline granites may be an indicator of their presence.CITATION:Shellnutt, J G, Hsia, T W-Y, Liu, T-C and Iizuka, Y, 2015. Cogenetic formation of the peralkaline syenite and oxide ore-bearing layered gabbroic intrusion of the Baima igneous complex, Emeishan large igneous province, south-west China , in Proceedings PACRIM 2015 Congress, pp 317–324 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By J Webb

"It is vitally important in projects where the cut-off grade is low that there is no contamination during the sampling and sample preparation process, both in the ore and the waste zones. Failure to identify contamination could have devastating financial consequences for a project. The use of a variety of blank types is essential for ensuring that contamination is identified and eliminated at every stage of the sampling and sample preparation process. This paper examines an instance where an effective assay quality assurance and quality control (QA/QC) program was able to identify and eliminate a source of significant multi-element contamination in the prefeasibility stages of an open pit project. This examination includes the: evidence for contamination findings of the investigation process of resolving the problem and correcting the data evidence for both addition of metal and dilution through contamination potential impact on the project had this issue not been dealt with. It was through the use of a combination of blank types that the QA/QC process at Mount Isa Mines (MIM) identified a contamination issue at the first crushing phase of sample preparation. Identification of the contamination allowed MIM to stop assaying activities and work with the laboratory to correct the problem. The sampling program could then be continued with no further doubts about the sample preparation process. Contaminated samples were resampled from retained core. With the continuous monitoring provided by the blanks program, it was possible to ensure that only clean results went into the resource modelling data set. CITATION:Webb, J, 2014. When nothing is what you need – the importance of using blanks at all stages of sample preparation, in Proceedings Sampling 2014 , pp 49–54 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 29, 2014

By S J. Henderson

Pumped co-disposal of coal processing waste was promoted in the 1990-2000s as a low-cost highperformance alternative to tailings dams. In particular it would avoid high up-front capital for rejects trucks and dam embankments, and would produce a combined waste deposit with better geotechnical properties than either coarse rejects or tailings. Overall, the promise was not delivered; in particular, upon discharge the waste segregated by size, and operators responded by moving the coarser waste to contain the finer waste. In consequence, not only did design analysis lag behind construction, but some of the initial expectations persisted with the result that analyses did not fully represent what was occurring on the ground. After more than twenty years inspecting, designing and tending Co-Disposal Areas (CDAs), it is apparent that they are essentially upstream constructed tailings dams with some more favourable aspects but also a few unique quirks. Although waste management technology has moved on somewhat, the high cost of changing CHPP waste circuits means that most mines with pumped codisposal will continue to discharge mixed waste slurry into CDAs. It is therefore worthwhile to share some lessons in the hope of promoting sounder design, operation and rehabilitation. These include: • Discharged waste does not form a homogeneous wholly competent deposit but instead comprises materials ranging from sandy gravel to silty clay with the distribution determined by movement of the discharge and decant structures; • CDAs circulate and contain a lot of water; • As a result of the first two points, some areas of the CDA comprise saturated fine waste that is no different from tailings and, like tailings, often behaves in an undrained manner; • Seepage is inevitable and desirable because strength improves as water is removed. However, stability is strongly impacted by pore pressures and in design these need to be rationally rather than optimistically considered; • As CDAs are built to about 40m or higher, strength-deformation characteristics of the foundation become more important; • Even if geomechanically stable, CDAs will need covers to prevent salts and acids from reaching the surface; and • Erosional stability of the cover material(s) will probably dictate maximum slopes for rehabilitation.

Jul 1, 2021

By S Rogers, D Stead, E Eberhardt

The last decade has seen a major increase in use of the discrete fracture network (DFN) approach applied to cave mining problems, often integrated within more complex geomechanical simulations. Because the value of the DFN model directly depends on the quality and quantity of available field data, there is the need to apply dedicated mapping procedures to collect sufficient structural data at the required engineering scale. This paper attempts to address several key questions about DFN modelling; for example: are current methods for fracture mapping suitable for DFN modelling? What are the critical parameters that we need to measure and what do we need to change in the current practice? Particularly at the earlier stages of a cave project, engineers may have to account for the lack of appropriate data, which manifests itself in the form of increased uncertainty and the difficulty to characterise variability in an objective manner using a limited set of data. DFN models could in principle be generated using limited data by assuming statistical distributions for the sampled parameters; however, engineers would need to be aware of the implications that such limited knowledge (and increased uncertainty) would have on stability analysis, fragmentation analysis and mine design. When used correctly, a DFN approach offers practitioners the opportunity to:maximise the use of fracture data collected from mapping of rock exposuresgenerate more realistic synthetic rock mass modelsprovide estimates of natural fragmentation that also account for rock mass variability.CITATION:Elmo, D, Eberhardt, E, Stead, D and Rogers, S, 2016. Discrete fracture network modelling – importance of accounting for data uncertainty and variability, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 845–852 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By S B. Sheldon

Wall control programs tend to be expensive and consequently require financial justification in order to get approval for the expenditure required. The difficulty faced in getting this approval is that the outcomes of a wall control program are all subjective – a prediction of wall stability and what the wall would do with and without the program. Determining a net benefit is difficult and often justification of a wall control program is based on gut feel, history and a good selling campaign to build a perceived need.This paper outlines a simple solution to this problem by applying risk management principles to wall control. The process is to identify the risks to the operation associated with current wall conditions and then build a risk database for different potential scenarios for each risk. A financial impact is assigned to each risk scenario to complete the database. A consequence and likelihood analysis of each of the risks is undertaken and a formula applied to estimate the projected cost to the operation for the current risk profile. The process is repeated for the predicted wall control conditions after the application of the wall control program. A successful wall control program will reduce an operation’s risk profile so this projected cost should be less than that calculated for the current scenario. The difference in the two projected costs is the value that the wall control program has produced and this value can be used to determine the net financial benefit potential for the wall control program.This methodology can also be applied to other improvement programs that focus on risk reduction such as vibration control.

Nov 8, 2011

By J Rutter, S Dunham

Technological advances in sensor and material handling technology has enabled a step change in mine operations performance. Sensors capable of monitoring the grade of broken rock mass can be mounted on shovels, truck loading units or conveyors allowing highly precise ore/waste decisions to be made on small parcels of rock, increasing selectivity. This increased selectivity has the potential to remove sub-economic material from the product stream prior to incurring ore treatment costs. Bulk ore sorting is capable of intervening at <10t “pods” on Run Of Mine conveyors, or alternatively at per bucket loading (5-100t) or truck scale (30-350t) parcels of ore. This Grade Engineering technique being developed by CRCORE (Rutter, 2017) can improve mill feed grade, remove deleterious materials and ensure that the high capital intensity ore treatment facility is presented with the best ore feed strategy. While this technology can improve mine economics, estimating the performance of a bulk ore sorting system is challenging. Traditional resource estimation practices such as Ordinary Kriging and Inverse distance weighting (IDW) are based on weighted averages, a process that smooths the grade profile, reducing modelled variance and dispersion. Its purpose is to generate a globally unbiased result but is less suited to generating a model of adequate granularity to enable confidence in local grade heterogeneity. This is an essential component for bulk ore sorting success. Estimating ore sorting performance requires knowledge of the grade-tonnage curve at the scale of the sensor diversion unit (SDU). Evaluation based on an estimator that smooths the SDU distribution will not correctly predict ore/waste separation or economic performance. Alternatives to traditional linear geostatistics have been tested on a variety of mineralisation styles. Additionally, a number of heterogeneity metrics have been developed to assist with evaluation and assessment. The difference between estimation for grade (metal) and modelling for traditional mining block models, versus methods used for predicting heterogeneity and variability are explored.

Nov 10, 2020

By J Boshoff

The management and operation of tailings storage facilities (TSFs) are often neglected until the process plant has to shut down as a result of this negligence or as a result of a catastrophic failure as was the case during the recent TSF failure in North America.TSFs are often regarded as non-assets and do not receive the attention they deserve in terms of technical expertise and financial provision. A TSF is not a simple structure but a complex and dynamic structure that changes throughout its operational life. The operational life of a TSF is the period in which there is the greatest opportunity for risks to occur. The failure of a TSF is normally not as a result of a single event but as a result of a consequence of events. These events are often not recognised in time due to a number of factors.Process plants and slurry pumping systems are operated at suboptimal conditions in order to maintain throughput. At the same time, the tailings properties are compromised in terms of slurry density and particle size distribution amongst other things. Tailings deposition cycles and drying cycles are not well understood and the tailings management strategy is not well tuned in terms of maximising consolidation and improving in situ densities. Pond control is also neglected. These are aspects that form the keystone to the effective utilisation of available deposition area as well as the frequency and cost of future embankment raises.Apart from operational issues, forward planning in terms of budget requirements, increases in tailings throughput, embankment raises, pipe replacements, etc are normally put on the back burner. Available deposition space at the time seems to render this planning obsolete.The bottom line is that responsible tailings management and proper forward planning can limit liability and reduce the bottom line in terms of cents per ton if correctly implemented by suitably qualified tailings managers and engineers.The aspects that need to be considered as part of responsible tailings management are highlighted in this paper.CITATION:Boshoff, J, 2015. Responsible tailings management, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 317–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By D Carroll

Mining of the zinc, lead and silver deposit at the Broken Hill Southern Operations site has been occurring for over 100 years. As a result of this, a significant amount of high-grade ore is now taken from narrow remnant pillars left between old stopes and zones of previously mined ground. Stopes have been filled with either hydraulic fill (also known as ‘sandfill’), cemented hydraulic fill (cemented sandfill), waste rock backfill or a mixture of these fill types.In the last ten years, there has been considerable success mining through narrow pillars where sandfill is exposed in the development face and/or walls using a ‘shell’ support regime, wherein a layer of bolted mesh is sandwiched between two layers of sprayed fibrecrete (25 mm fibrecrete, then mesh and bolt, followed by a final 50 mm layer of fibrecrete). Shell support is also used in very poor, broken, relaxed ground conditions and in areas filled with cemented fill (sandfill with a minimum four per cent cement content).The next stage of innovation has been to develop a technique for mining through old stope voids filled with uncemented sandfill, known locally as ‘contours’ (old cut-and-fill working), an activity where unconsolidated sandfill can run at the face and from the backs. The challenge is to prevent exposed sandfill in the face and the backs from failing before it can be supported.To achieve this, the Southern Operations mine has implemented a technique in which 6 m long spiling bars are used to strengthen and stabilise the sandfill in front of the face. The hollow steel bars are driven in around the heading perimeter in a closely spaced pattern then pumped full of grout. The bars and the grout stabilise the sandfill in front of the face, preventing it from failing into the drive during excavation and prior to further support being installed.A final support system consisting of shotcrete, mesh, bolts and steel girders is installed as excavation progresses. Both the initial and final support systems are essentially passive support systems designed for a low-stress environment (as the stress originates mostly from the mass of unconsolidated sandfill).This process is slow and labour intensive. Fifteen separate cycles of people/machinery are needed to progress one equivalent heading cut (compared to six for a standard fibrecrete- and bolt pattern-supported rock face heading). This slow pace introduces scheduling challenges, but the process opens up parts of the orebody that were previously uneconomical to mine.CITATION:Carroll, D, 2014. Mining through sandfill using spiling bars, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 95–100 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

Mother Nature controls, technical professionals model and miners decide. Decisions to explore, mine and mill. Mine decisions, mine design, planning and scheduling are subject to the quality of models û geological models, geotechnical models, resource models, density models. The closer these models are to reality, the more accurate the predicted outcome. So why is it we delegate the modelling tasks to the most junior and least experienced people? If we insist on this, we need to support them û to provide them with æexperience acceleratorsÆ. Technical mentoring is the most effective way to provide the right information at the right time. When this information (read skills) is supplied at the right time we can inject experience into the quality of our modelling and into our decision- making processes. The objective of this paper is to share those behaviours and manners that foster relationships and create frameworks for skills and experience transfer. Central to this is an understanding of how adults learn, an understanding of the basic rules of mentoring etiquette, and the three keys to building meaningful mentoring relationships. An understanding of adult learning processes and styles provides a structure within which a mentor can understand the learnerÆs perspective. Understanding the world from the learnerÆs point is critical to selecting the right language to engage, teach and transfer skills. Basic rules of mentoring etiquette like timeliness, respect and trust need to be brought into the consciousness so they can be agreed on and monitored to prevent conflicts in cultural and generational norms between the mentor and the learner.Meaningful relationships hinge on the three behaviours: truly listening, rather than just hearing; understanding the technical issues within the WIIFM (whatÆs in it for me?) question; and facilitative behaviour. Stronger and more meaningful technical mentoring relationships within our industry will bridge the generational gap and ensure we can capture and capitalise on the wealth of grey hair experience and develop an informed group of young decision-makers.

Jan 1, 2006

This paper reports the advances made during the development of underground mine fill technology from circa 1960 to the present and, in particular, indicates where increased input from process plant metallurgists û mainly milling, but also smelting û can contribute to further advances. Fill types pertinent to the discussion are partially deslimed, partially dewatered mill tailings fill (uncemented, cemented) and paste fill. Pertinent process plant includes hydrocyclones, thickeners, filters, elutriation tanks, holding tanks, mixing mills, pumps and pipes. Control instrumentation is a critical component of each of the process plant units. The impact of smelter practice on filling is not considered in this paper, except to note that some smelter slags are, or have the potential to be, active pozzolans and when ground to the specific surface area of Portland cement can act as partial Portland cement replacements, a factor of economic and operating significance when Portland cement supply lines are considerable and/or tenuous. The important role of process plant metallurgists has long been recognised, with Thomas, Nantel and Notley (1979) including them as one of the many categories of professionals with contributions to make. With the ever increasing sophistication of mine fill practice and its ever increasing acceptance as an essential component of the mining/ milling/waste disposal process, the scope for contributions by the modern breed of highly educated, specifically trained process plant metallurgists is becoming ever increasingly obvious.

Jan 1, 2006

The borehole televiewer is a downhole geophysical logging device that produces continuous, oriented, 360¦ images of the drill hole wall. Two types of borehole images are currently being generated at the BHP Billiton Mount Whaleback deposit. The optical televiewer (OTV) tool captures a ærealÆ image of the borehole wall whereas an acoustic televiewer (ATV) generates an image through variations in physical borehole size, scattering the energy from an acoustic beam. Orientation of the resulting ævirtual coreÆ is derived through magnetometers and accelerometers, providing values within one degree for both inclination and azimuth. Downhole structures such as fractures, joints, foliations and bedding planes are selected directly off the borehole image, recorded and displayed in a 3D modelling package along side adjacent drill holes. Measurements are corrected from apparent to true dip and magnetic to true north. Strata-bound magnetic anomalies are identified and corresponding measurements excluded. The importance of borehole imaging increases substantially with its ability to integrate the OTV and/or ATV data with other forms of lithological and structural data. At Mount Whaleback, the borehole televiewer has been implemented to provide information for geotechnical exploration including structural analysis, lithological characterisation and rock-mass conditions. Within the large area in and around Mount Whaleback, drilling may intersect a number of different geological formations with various rock types and conditions. With the application of the borehole televiewer, reverse circulation drilling can provide information traditionally obtained by diamond drilling.

Jan 1, 2007

By M M. Pande, M Ishfaq

The effect of aluminium on nitrogen solubility was investigated by equilibrating melt comprising master alloy of Fe-Al with pure electrolytic iron in a controlled atmosphere (pure argon) at 1873 K. Nitrogen in the samples was measured by sampling technique using inert gas fusion absorptiometry. It was found that nitrogen content decreases steadily with aluminium concentration and gradually, becomes close to 1 ppm for very high aluminium steels. Wagner’s second order interaction parameter formalism has been used to estimate the equilibrium constant and interaction parameters. Scanning electron microscopy (SEM) investigation showed, dual-phase inclusions comprising AlN phase surrounding alumina core. The 3D morphology of inclusions was studied by extracting the sample from the top and the central bottom portion of the solidified ingot. A sparse distribution of nitrogen was found for most of the inclusions which manifested the presence of almost pure alumina inclusions with different morphologies and sizes.

Jun 19, 2024

Detailed underground mine design and optimisation studies undertaken by the author over the past few years have clearly demonstrated that additional value can be created by varying the cut-off grade (COG) spatially throughout a deposit as well as over time. This additional value can be particularly significant for marginal operations. This paper, by way of worked examples, illustrates the conceptual and practical considerations of applying a differential cut-off policy for an underground mine to both maximise value and manage risks associated with production and metal price volatility. Consideration is given to both the design stage of a new mine and to the strategic and practical application of a differential cut-off policy in an operating mine.

Jan 1, 2005

In May 2000, Kanowna Belle Gold Mines (KBGM) carried out a detailed Truck versus Shaft Haulage Study. The study showed that whilst the shaft option had many operating cost benefits the capital costs were too high, therefore the truck option was selected. In May 2001, the concept of achieving æshaft typeÆ benefits without the capital costs was floated. This is achieved by separating the hoisting of ore from other mining activities. The general concept is that material from underground is transported to a central location and then transported to the surface by a special truck fleet, thus removing the dependency between trucks and loaders, providing the mine with surge capacity and decreasing operating costs. At KBGM these advantages have been gained by installing an ore pass system with a plate feeder at its base that directly loads trucks. This provides the mine with a haulage system with enough surge capacity to remove the interdependency between trucks and loaders. The plate feeder is situated just off the decline which creates the opportunity to use larger more reliable, lower cost trucks. A number of truck types were considered for the truck loop including Elphinstone AD55Æs which are the truck type being used on site prior to the truck loop, CAT 775EÆs and power trailer road trains. This paper covers the philosophy behind the truck loop, the truck selection process, project installation and commissioning, people issues and the benefits expected by the operation. As of May 2002, the project is nearing completion, with decline haulage expected to commence in July 2002.

Jan 1, 2002