Search Documents

By L Richards, R L. Brathwaite, C Mazenga

Underground mining of gold-silver bearing quartz lodes was carried out in the great mines at Martha Hill, Waihi over 70 years from 1882 until 1952. Shafts and stopes reached a total depth of 600 m on 16 levels, with workings extending laterally some 1.6 km, and as new reefs were discovered the workings extended beneath parts of the township. Over their long life the mines produced 1217 tonnes of gold-silver bullion from processing 12.2 million tonnes of mined ore. In the early-1980s drilling proved large reserves of gold and silver ore remaining in stock-work zones between the previously mined lodes. This led to a new era of mining at Waihi with the opening of the Martha Hill open pit in 1988. A series of three sink holes have formed above unfilled stopes of the Royal lode. In 1999 a sudden collapse crater 40 m in diameter occurred near an occupied part of Waihi, placing in danger several houses and a busy street. This crater formed close to a similar crater that occurred in 1961. The 1999 collapse resulted in subsurface investigations and risk assessment studies being commissioned by the local Hauraki District Council. However, a further 50 m diameter collapse crater in December 2001 formed in a residential area, swallowing and wrecking an occupied house, fortunately without injuring its five occupants. Two other houses were perched on the crater rim. The 2001 collapse led to an acceleration of the work being carried out by the Institute of Geological and Nuclear Sciences Ltd. (GNS) to identify the extent of the old underground workings at Waihi. For the risk assessment detailed rock mechanics analyses were made to consider the stability of the underground mine stopes, in terms of the stope back, hangingwall, footwall and crown pillar failure mechanisms, as well as void migration. The collapse crater areas were analysed using using several methods, including analysis to simulate the probability of void migration from unfilled stopes to the surface using the @Risk program. The analyses show that in the cases of the actual collapse craters, the voids have a high probability of migrating to the surface, thus providing a method of testing the void migration modelling. Modelling analysis applied to the remaining stopes of the old underground mines show there are further areas where void migration from unfilled stopes has a high, medium and low probability of reaching the surface as a collapse crater. The locations of these probabilistic hazard zones were outlined using the @Risk modelling and deterministically by using the dimensions of the historical collapses applied along the length of the stopes. Consideration of the æincubation periodÆ (the time interval between the cessation of mining and the occurrence of collapse) and comparisons with mine subsidence histories overseas, indicates that further collapses are likely to occur over the next 50 years. Risk assessment estimates made using property values and occupancy levels within the three hazard zones, were compared with Societal and Individual Risk criteria. Results indicate that safety within the high and medium zones may be unacceptable.

Jan 1, 2003

By L Chaffey, M Buckland

The minerals industry has enormous potential to positively contribute to sustainable development and many leading companies have concluded that their long-term success is directly linked to their ability to leave a lasting positive legacy. While there are many examples of success, there have been failures as well and much work has been done in recent years to define the role of the minerals industry in sustainable development and identify the key elements for success. In the past, our sector could point to the taxes and royalties it paid, the exports it generated and employment it created and felt confident that its contribution would be recognised and duly acknowledged. This is no longer the case. Critics of the industry have highlighted resource-rich countries that have failed to capitalise on their resource wealth and have arguably lower standards of living than their resource-poor peers û the æresource curseÆ hypothesis. Recent research has done much to clarify the factors that contribute to a countryÆs success or failure and all stakeholders in the industry now need to include these learnings in their approaches going forward. We know that our long-term success relies on embedding a company- wide approach to sustainable development into all aspects of our business operations. In this paper we highlight BHP BillitonÆs experience in the development and implementation of policies and systems designed to enhance our contribution to sustainable development. We detail the business drivers for excellence in this area and the key external codes and initiatives that have shaped our approach. The values-based BHP Billiton Charter, Sustainable Development Policy and associated Health, Safety, Environment and Community (HSEC) Management Standards are central to our approach. Implementation is reviewed through our HSEC audit program. One area in which we have placed particular emphasis is our approach to community development. BHP Billiton has a corporate target to contribute one per cent of its pre-tax profit on a three year rolling average to voluntary community programs. As our profit stream has increased with the minerals boom this is approaching an A$100 million commitment. In our paper we detail how we are working to ensure we maximise the value of this contribution for our communities and our shareholders.

Jan 1, 2006

By M Steinberg, M Amarant

Upstream Classifier are well-known in the iron ore industry for at least 15 years. At present, more than 60 units are in operation in Western Australia. The advantage of this technology is their capability to produce three products with one equipment – iron ore concentrate, iron ore middlings for further processing and slimes (tailings). The principal of this beneficiation process – upstream classification and upstream separation – will always remain. However, the optimisation of the classification and separation efficiency of the equipment itself is a continuous process driven by enhanced automation and instrumentation, design changes and the use of upstream and downstream information and requirements. Besides efficiency, the safety, maintenance and replacement conditions are very important subjects for the operation of an iron ore mine. The aim of this paper is to present a new allflux® upstream classifier design, which has been developed together with several iron ore producer from Western Australia. The new design benefits from its sustainability approach by dividing the entire equipment into small reusable parts. As a result, maintenance is minor, replacement much faster, lifetime much longer and costs much lower. Furthermore, it demonstrates new features to prevent hazardous working conditions such as confined space as well as new fixing devices to speed up the replacement of certain items and parts.

Sep 18, 2023

By A Nugraha, H Thanasekaran, K Tatetdagat

The Kanowna Belle gold mine is located in the Eastern Goldfields of Western Australia, approximately 18 km north-east of Kalgoorlie. The processing plant is designed to process 2 Mt/y and has the capability to treat both refractory and free milling ore from the Kanowna Belle and Kundana mining operations.The Kanowna Belle ore is refractory with the gold mineralisation occurring mostly as fine-grained inclusions in pyrite or as very fine-grained gold located in pyritic arsenic rich growth zones. The Kanowna Belle refractory process includes flotation, roasting of the flotation concentrate, and calcine leaching to extract the gold from the ore.Mineralogical analysis of feed and tailings streams from the flotation circuit have shown that the gold bearing minerals are well liberated and confirmed they are mainly associated with pyrite. Nearly 40% of the flotation circuit losses are in the -38 µm size fraction. To improve the flotation circuit recovery, the fine particle gold recovery was targeted. A Cavitation Tube column was selected for the site-based pilot test work program. This paper presents data generated from the on-site test work, and the benefits of the Cavitation Tube column to improve fine particle flotation.CITATION:Nugraha, A, Tatetdagat, K and Thanasekaran, H, 2018. Flotation circuit efficiency improvement at Northern Star Resources Limited’s Kanowna Belle gold mine, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 403–412 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By G Pasin, F Wirfiyata, G Khomaeni, W Valery, A Maclean, A Jankovic

The grinding circuit at PT Newmont Nusa Tenggara (PTNNT) – Batu Hijau mine consists of two SABC (semi-autogenous milling, ball milling, pebble crushing) trains, including four 20'?×?33'6? ball mills that have been lined with steel liners since the commissioning of the plant in 1999. During 2011 and 2012 an industrial trial was conducted to evaluate Poly-Met liners (a combination of rubber and steel liners). These new liners were installed in two of the ball mills (ball mills 1 and 2) and operated in parallel with ball mills 3 and 4 with steel liners.The objective of the trial was to compare the plant performance with the Poly-Met and steel ball?mill liners with regards to wear life, mill throughput, grind size and total unit costs. The trial was conducted over the entire life of the liners. The evaluation methodology implemented consisted of frequent spot sampling around the ball mill circuits, complete surveys/audits in both ball mills, and detailed analysis of process data. This paper presents the results of the industrial trial and main conclusions.CITATION:Maclean, A, Wirfiyata, F, Khomaeni, G, Jankovic, A, Pasin, G and Valery, W, 2014. Ball mill Poly-Met liner evaluation at PT Newmont Nusa Tenggara – Batu Hijau mine, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 255–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

Dr Eric Bumstead is to be commended for his recent paper on gold analysis, published in the March 1984 Proceedings. It is not often that someone in industry, rather than academia, takes the time to collect and report on such a volume of data, data which is of interest to everyone involved in gold exploration and development.After reading the paper I felt, as a geochemist and as ayer, that there was another side to this whole question of analysis that few people are aware of, i.e. the problem facing a laboratory and how the laboratory can try to give the customer maximum value for money spent.Analyses for gold are carried out for different reasons, depending on the aims of the geologist or metallurgist who presents the samples. These can broadly be separated into three classes, to answer the following questions.1. "Is there any gold in this sample?"2. "Approximately how much gold is there in this sample?"3. "How much gold is there in this sample?"In every case there is a different balance between accuracy and precision, cost and avoiding chemical problems. By "chemical problems", I mean such possibilities as samples containing high levels of sulphides, gold present as tellurides, cyanide being present, contamination with mercury, and other mineralogical oddities, plus problems such as samples containing grease.There is no such thing as one assay to cover all possibilities.Samples in category I come mostly from early stages of exploration.There are often large numbers of samples, their mineralogy is not well known and hence chemical problems could exist, but the explorer wants assays at a minimum level of precision and expects minimum cost. These characteristics do not easily come together, for although the precision required is low, the accuracy required is high at low levels. A small positive result when the true answer is nil could lead to a fruitless search and a waste of money. Conversely, a nil result, when the true answer is a small but significant level of gold, could lead to the passing over of an area that may warrant further work.Because there are conflicting requirements for this type of assay, the methods chosen must be a compromise and different assayers will balance these requirements differently and come to different conclusions. The methods cover sample preparation, assay sample size and variations in assay techniques.

Jan 1, 1984

By Q Yu, G Ren, Z-Y Chen, J Yang

The wedge shape theory of the rock fragmentation range in bench blasting is presented according to the dynamic characteristics of rock fragmentation by blasting in open pit under the condition of hole-by-hole initiation. The finite element software ABAQUS was used to analyse the rock fragmentation mechanism. The rock mass stress contours, crack propagation and damage evolution of different moments were obtained. The results showed that the wedge shape theory of blasting is closer to the rock fragmentation in hole-by-hole blasting and is useful to the design and calculation of charge weight.CITATION:Yang, J, Chen, Z-Y, Yu, Q and Ren, G, 2015. The wedge theory of borehole charge design for bench blasting and its numerical simulation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 169–176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D R. Andrew, K T. Morrison, J F. Tiedgen

Waste blasting in iron ore operations can pose a number of technical challenges, including blasting through variable geology and blasting soft ground in wet conditions. Blast patterns are designed to be loaded with a specific range of explosives with unique characteristics and properties. Each explosive product will produce an optimal blast outcome for a given set of blast parameters and ground conditions. Sites characterised by softer rock typically require low-density, low-energy explosives. Historically, these products have contained a high ratio of porous ammonium nitrate prill and are only suitable for dry blastholes. When blastholes within a pattern are found to be unsuitable for such explosives due to wet, damp or muddy blasthole conditions, a new product is selected. While it is easy to switch products to match blasthole conditions, the different properties of the new non-ideal product can impact blast performance and increase loading times and costs.Flexigel™ is a solids-sensitised emulsion blend suitable for loading at variable densities and energies in dry, damp, muddy or wet blastholes. It is a universal product that can be loaded to match ground and blasthole conditions or complement other explosive products.At Fortescue Metals Group’s Cloudbreak site, Flexigel™ was trialled through a series of matched pair blasts in order to optimise blast outcomes in conditions that were non-ideal for existing explosive products and to reduce the overall cost of drill and blast operations. Flexigel™ yielded improved instantaneous dig rates and improved loading efficiency when compared to a traditional emulsion blend. The results also indicated that variable-density and variable-energy products afford greater flexibility for optimising blast outcomes across all ground and blasthole conditions trialled.Trials of Flexigel™ at Cloudbreak have shown that a variable-density solution is available for conditions where traditional explosive products are non-ideal. As such, Flexigel™ is able to fill a major void at any operation where the desired low-density, low-energy explosive product must be substituted for a more expensive traditional emulsion blend or heavy ammonium nitrate/fuel oil.CITATION:Andrew, D R, Morrison, K T and Tiedgen, J F, 2015. Flexigel™ – a variable-density solution, in Proceedings Iron Ore 2015, pp 413–418 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By K Clode, J Al-Shdifat, S Daykin

Planning for a circular economy allows for previously untapped market opportunities to be explored, resulting in new, innovative revenue generating opportunities, while also reducing environmental impacts. In particular, rare earth elements (REE) are in rising demand as they are key components of over 200 products across a wide range of applications (Xie et al, 2023) including renewable energy technologies. There is a geographical disparity in deposits, with China being the top producer, generating 70 per cent of global production in 2022 (Laboure, 2023). This single dominating source has created supply chain concentration and hence supply risks for other nations, providing a driver for finding alternative sources, such as mine-influenced water (MIW) and tailings. In this study, Isle presents a robust due diligence methodology for undertaking a global horizon scan into REE recovery technology, for a large mining company, from tailings decant water on a specific site. Previous studies of the tailings decant water at this site had shown potentially significant concentrations of both heavy and light REE, but challenges such as high flow, very low pH and high concentrations of iron had previously made recovery unfeasible. Due to these challenges, the horizon scan focused on technologies that had the potential for selective recovery, despite the challenges with water quality, and considered a range of Technology Readiness Levels (TRLs). This included an adsorption-based process that has the potential to selectively separate individual REE, and a polymer based selective flocculation technology.

Sep 1, 2024

Traditional in situ fan flow test methods under accepted standards require determinations to be made of both static pressures and total pressures during testing. This is to determine the resultant velocity pressures, which are vital in the accurate determination of the final fan airflow. These crucial velocity pressure (Vp) determinations are normally determined using simple manometric instrumentation such as an electronic manometer or an inclined liquid filled manometer. There is relatively little noise or fluctuation in the static pressure determinations and they can be quite easily and accurately recorded. There is almost always considerable fluctuation in the velocity pressure determinations though due to the highly turbulent and irregular velocity profile normally found in such in situ installations. This velocity turbulence means that the recording of such data is subject to random human error as the observer tries to average such fluctuations mentally during the observation period. Worse than this, and in the extreme, the recording of such velocity pressure data could actually easily be misreported if, for some reason, persons chose to do so.The author has devised a field method using highly accurate quartz crystal logging barometers to objectively record these velocity pressures. The method eliminates the ability to either mistakenly or intentionally misreport these crucial velocity pressures and is carried out in parallel with the recognised methodology, so result comparisons can be drawn. As such, a far greater level of confidence can be achieved in the final flow performance results than using the traditional more subjective method. Further to this it is difficult and almost impossible to refute the results using this ancillary substantiation method.The accurate determination of fan flows due to the impost of the carbon tax has taken on much more significance given the financial impacts in Australia at this time. The methodology detailed herein can be applied equally for both fan flow compliance testing and the verification of mine airflow data for greenhouse gas emission evaluations.The paper utilises the results of one 24-point pitot traverse to demonstrate the various findings. These include the very wide range of velocity pressures, which were logged at most of the measuring stations. It also illustrates how the method is utilised and compares the results derived from both this method and the more subjective traditional method along with the benefits of logging the velocity pressure results during the testing process.CITATION:Rowland, J A, 2013. Removing some subjectivity from traditional BS 848 and ISO 5802 in situ fan flow tests, in Proceedings The Australian Mine Ventilation Conference , pp 155-162 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By S Mitchell

Jetcrete Australia Pty Ltd, shotcrete contractor took the initiative in 2008 to discontinue the use of ‘road registerable’ concrete trucks for all underground works in Australia and internationally.The rationale for this decision was basic, safety. Historically these vehicles have been and still are involved in far too many accidents; this obvious trend needs to be addressed by engineering out the root cause of the problem which in this case is suitability for purpose.Road registerable concrete trucks have been widely used for the delivery of concrete in Australian mines for many years prior to and after the inception of wet shotcrete as ‘in cycle’ ground support in underground excavations around 1992. With this inception came a wide interest in the shotcrete process and an influx of new shotcrete contractors, all using road registerable concrete trucks to deliver the large volumes of Shotcrete required for these services and in turn largely increasing the use of these vehicles underground. The road registerable concrete trucks were difficult to control and each trip underground required the operators to maintain good management of the inherent risks. We virtually had no reasonable alternative for the industry and could only encourage the operators to drive with soft controls such as, reducing overall speed to a maximum of 15 km per hour when declining, regardless of the road conditions, coming to a complete halt prior to turning into any sharp corners, remaining in the same gear both inclining and declining.

Mar 21, 2011

By D Connelly

Magnetite ores can be used to produce very high-grade concentrates that are suitable feed for the direct reduction process route but the high sulfur content of some concentrates can cause substantial environmental issues. Processing of high sulfur magnetite ore is therefore increasingly problematic for the industry. Generally, the industry demands a concentrate with <0.05 per cent sulfur and <2 per cent silica. This paper reports the outcomes of a study to produce a concentrate with the requisite low sulfur content from a sulfur-rich magnetite ore. The main findings may be summarised as follows: if the sulfur is present in magnetite as nonmagnetic pyrrhotite or pyrite, it can be beneficiated using magnetic separation and hence, monoclinic pyrrhotite is magnetic and is magnetically recovered with magnetite leading to a concentrate that is too high in sulfur. X-ray diffraction and QEMSCAN analyses revealed that the magnetite concentrate was liberated at P80 30 microns and was associated with maghemite, pyrrhotite (magnetic), carbonates and hematite with very low amounts of chalcopyrite, sphalerite and arsenopyrite. Sulfur removal using flotation was the first stage of investigation and this required flash flotation in the grinding stage followed by column flotation of the initial concentrate to generate the final concentrate. At the same time, it was observed that oxidation of the pyrrhotite had a negative effect on its flotation requiring copper sulfate to activate it. Bioleaching and concentrate leaching were also considered and achieved over 90 per cent sulfur removal but were deemed unsuitable owing to the production of highly reactive wastes and high CAPEX. Reference is made to a number of operating magnetite producers and how they manage the sulfur in feed.

Sep 18, 2023

By P Holtham, J Meng, E Tabosa, W Xie

Turbulence and its distribution are of great importance in flotation, and have received considerable attention recently. However, there is no mature technique to measure turbulence in three-phase (liquid-solid-gas) industrial flotation cells due to the opaque, highly aggressive and abrasive nature of the slurry involved. Previous research has shown that the piezoelectric vibration sensor (PVS) is a promising tool for turbulence measurement in industrial flotation cells. The PVS is a robust device that converts mechanical vibration to electrical signal, from which turbulence information can be extracted. An improved calibration method has allowed development of a frequency model to calculate the force applied to the sensor. Experimental results and comparison with laser doppler anemometry (LDA) have shown that the PVS can measure fluid kinetic energy, which is related to turbulent kinetic energy, a parameter used in the literature to represent turbulence in flotation. Laboratory measurement in a two-phase (water and air) 60 L cell and with slurry in a 3.5 L cell gave good stable results and mostly consistent trends between the measured turbulence profile and cell operation. When applied in a 300 m3 industrial cell filled with water, the addition of air or slurry to the cell resulted in a shift in the turbulence profile. This is expected because a change in fluid density will change the force applied to the sensor. It is therefore concluded that the piezoelectric sensor is an easy-to-use and robust technique that is fully capable of measuring turbulence in industrial flotation environments.CITATION:Meng, J, Tabosa, E, Xie, W, Runge, K C and Holtham, P, 2014. Development and application of a piezoelectric sensor for turbulence measurement in industrial flotation cells, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 457–470 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By J Taylor, A Dubowik

To increase the efficiency and improve the quality of diamond drilling at Olympic Dam, mine geologists have adapted and modified common practices in order to overcome the challenges imposed by such a unique environment. Mine geologists have to take into account both the complex geology during the diamond drill hole design phase, as well as incorporating diamond drilling into the larger-scale scheduling process already employed at Olympic Dam. This study seeks to explore how such modifications have evolved over time.The geology of Olympic Dam influences the design process of diamond drill holes, particularly due to the variation of lithology and alteration, as well as the presence of magnetite and major structures within the orebody. Exclusion zones are used to manage interactions with existing and planned mining activities, and their size is dependent upon the geology of the area. Specific deviation checks are used to monitor the deviation of diamond drill holes with respect to these?zones.The highly interactive environment of Olympic Dam requires unique planning for diamond drilling, resulting in the production and implementation of both long- and short-term schedules. Long-term schedules are targeted at determining drilling locations and ensuring drilling is completed prior to stope planning, while short-term schedules aid in enabling access to ensure timely set-up of drill sites. Estimated drilling rates, determined by expected lithologies and historical data, feed into the short-term schedule to assist in managing the operation and minimising the downtime of diamond drill rigs. A mine geologist is appointed as a diamond drill coordinator to organise and manage diamond drilling at a scheduling and operational level, streamlining the entire process.Analysis of historical data shows a strong correlation between implementation of the aforementioned practices and improved drilling rates. This study shows the importance of adapting universal tasks to particular environments and circumstances. Mine geologists at Olympic Dam continue to acquire knowledge to further improve the modified drilling practices as operational requirements, production pressures and economic factors change.CITATION:Taylor, J and Dubowik, A, 2014. The evolution of diamond drilling practices at Olympic Dam, in Proceedings Ninth International Mining Geology Conference 2014 , pp 271–280 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By T Sua, B Wright

"BHP Billiton West Australian Iron Ore (WAIO) conducts an extensive geometallurgy program for its iron ore deposits in the Pilbara with the focus on determining the lump yield (the mass percentage of &gt;6.3 mm rocks) and the lump and fines grade for iron ore products. The geometallurgy program provides accurate information to design engineers and technical marketing teams on the performance of different iron ore mineralogies for future deposits. Additionally geometallurgy results are being used to guide short-term production planning with their introduction into short-term geology models and grade control models. The data that underpins this knowledge is from dedicated geometallurgical programs, drilled using PQ (~83 mm) holes. These holes are crushed by intervals that are based on geological definition which provides an indicative lump yield and lump and fines grade. The lump is then subjected to standard dropping and tumbling test stages to produce a simulated lump and fines product. In the past, quality assurance, quality control holes were drilled using HQ (~64 mm) holes for geochemistry purposes. These holes were crushed to provide an indicative lump yield and lump and fines grade and then 100 per cent is sent for assay (with no dropping and tumbling). Utilising data from HQ holes can significantly increase the indicative geometallurgical data available. This paper compares the geometallurgical results from both PQ and HQ holes from a range of bedded iron deposits (Brockman and Marra Mamba). The PQ and HQ data are compared by orebody, stratigraphy and depth to exclude factors that are expected to influence geometallurgical results.CITATION:Wright, B, Sua, T, Robertson, B and Van Dijken, B, 2016. Comparison of Diamond Drill Size on Iron Ore Geometallurgical Results, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 161–166 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By L Bertoss, D Carvalho

In the last decade, the use of advanced implicit modelling software/algorithms in mineral resource workflows has become a best practice in the mining industry. In most cases, these workflows can easily replicate the level of detail of explicitly modelled geometries, even for very complex deposits. These techniques are flexible and can produce fast results since software is responsible for generating 3D surfaces and solids based on geological and interpretation data. Nevertheless, depending on how unique and complex some deposits are, intense manual editing and input are required to honour the geological context and produce the desired outcome. The current geological modelling workflow at George Fisher Mine (GFM) is based on the semi-automatic built-in tool that generates stratigraphic sequences (stacked lithology layers) based on logging and mapping data. This tool (stratigraphic sequence from Leapfrog Geo™) works for the majority of areas in the mine but fails to capture observed mineralisation pinch-outs in operational areas and at extrapolated boundaries of the deposit. These pinch-outs have the potential to negatively impact grade forecasts if not resolved manually. Using built-in software tools only, the alternative for a more accurate model is to generate each individual layer and adding tens of thousands of manual interpretation points to honour pinch-outs (based on the amount of existing drilling in the mine and number of layers). This approach would require an estimated minimum of two to four years of a full-time employee (FTE) to be exhaustively completed. This study presents an automated approach to generate pinch-out points using a set of Python scripts that only take a few minutes to run. The newly generated points are then combined into the commercial software workflow as interpretation points, honouring observed pinch-outs. The remarkable time difference between approaches removes chance of manual errors and allows mine geologists to spend valuable time in validation and testing of scenarios, ensuring they are more representative of the deposit’s geology.

May 24, 2023

By C K. McKenzie, P Popov, B E. Papillon, I Kharitonenko

Flyrock produced by blasts in surface mining and quarrying is a major hazard that can result in serious injuries or property damage. This paper presents a fully integrated and automated approach for reviewing blast outcomes from a wide variety of rock blasting environments from the perspective of flyrock safety associated with blasthole collar ejections. The process is applied at a corporate level for an explosives service provider handling up to 100 blasts per day from mines, quarries and construction sites throughout the US.Flyrock risk minimisation has inspired research and the associated development of a reliable flyrock model to estimate flyrock ejection velocities and the resulting maximum projection distances of fragments. In spite of significant achievements in this area, flyrock incidents continue to occur, mostly due to implementation mistakes. An efficient preventive measure is continuous blasting process improvement that relies on on-site video recording, storage, automatic analysis and classification of the recorded blasts followed by the automatic generation of reports.In this paper, a novel blasting video analysis system that is capable of processing a large quantity of video records is presented. Blast analysis and parameter measurement are fully automated and are carried out using videos recorded with a conventional consumer camera. The blast video recording process does not require the use of surface markers, range poles or objects of a predefined size for scaling purposes.Although automatic video analysis is commonly used in many application areas, such as video surveillance, traffic monitoring and robotics, the algorithms that have been developed to recognise and track solid objects with well-defined shapes, textures and colours are not efficient at dealing with blasts, which, by their nature, have dynamically changing parameters. Moreover, very strong camera vibration caused by blasts that cannot be totally compensated by camera image stabilisers may cause conventional computer vision algorithms to fail.This paper presents novel computer vision methods developed for automatic tracking of the trajectory from a blast ejection point to the highest point reached by blast particles and the ejection velocity. The system also uses colour and motion analysis to detect the emission of toxic fumes during a blast. The solution is vibration tolerant and can differentiate foreground and background data, even in the presence of camera vibration. Moreover, the blasting video analysis method can automatically categorise correctness of the measurements and therefore indicate cases when additional visual inspections may be required to verify reports generated automatically.CITATION:Kharitonenko, I, McKenzie, C K, Papillon, B E and Popov, P, 2015. An automated system for flyrock and fume monitoring of blasts, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 417–424 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By F Musa

One of the main energy efficiency opportunities identified from the majority of mine site energy audits is to optimize the comminution circuit to reduce energy consumption through improved throughput and product size distribution. Typical analysis reviews comminution process efficiency/inefficiency i.e. utilization of grinding mills, process bottlenecks and product vs. target size, to identify instances of overgrinding or undergrinding. From this, it is possible to establish the potential improvement that could be gained through formal plant optimization and what the optimization program would entail. It can also sometimes reveal immediate opportunities for process improvement. This paper presents steps that can be taken to optimize the efficiency of comminution circuits.

Aug 8, 2011

By H Khoshrou, A Siamaki

Blast designs can have productive and non-productive impacts on downstream stages, mine productivity and operating costs. On the other hand, ground vibration, fragmentation, and back break caused by blasting impose damage and financial penalties and which must be controlled by blast design. One of the significant variables in blast design is the burden. In this study, the potentials of artificial neural network are investigated in prediction of burden in the Sungun copper open-pit mine. Input data were assembled through 18 blasting blocks according to different levels and experimental geomechanical investigation. To construct the model blastability index, uniaxial compression strength, hole diameter, specific weight of rock, rock quality designation and cohesion strength are taken as input parameters, whereas, burden is considered as an output parameter. Mean square error was used as the performance function and back propagation algorithm as the training function, containing four hidden layers and 14 data sets. Four sets of data were used to make sure that correct training had been carried out. This produced the coefficient correlation of 0.662.

Sep 26, 2011

By T Leidich, M Van Zyl, H Lacy

Mining ‘as usual’, until the most recent decades has resulted in limited landform planning and a general lack of mine waste landform design. Material characterisation, mine planning and dedicated professionals undertaking these tasks were rarely available or in place at the majority of mines. This has led to landform instability, erosion, sediment and poor quality water emanating from mine landforms. In many cases rehabilitation and reclamation failed and these sites have ‘landform features’ that are difficult to relinquish or leave and have little or no apparent land use. In many cases mined landscapes around the world have resulted in a less functional and degraded environment, with deleterious impacts on surrounding ecosystems.This situation is now slowly being addressed, as global companies, academics and practitioners and their organisations have started to exploit the ideas from an integration of earth sciences and mining through the application of planning software dedicated to the design of landforms.This development has had its genesis primarily in the United States. We suggest that process has been driven, in recent decades, by the application of resources in response to the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), (USA Congress 11 December 1980) and other mine reclamation legislation enacted by federal and states regulators in the USA. The combining impact has seen a huge transfer of capital back from the public purse and ‘potentially responsible parties’, into abandoned mines to affect control, remediation, and reclamation/rehabilitation of those mines.Given this investment in rehabilitation and reclamation, people engaging in the business of landform planning have had the opportunity to address landform reclamation of historic and active sites. The skills of engineers and scientists with improved technology, waste rock characterisation and modelling tools have been combined resulting in the evolution of landform design and in mine planning of active mines. This has delivered cost-effective, sustainable mine closure designs for over 30 years. Integration of mine design with an understanding of geomorphic principals and the natural landscape, coupled with waste and soil characterisation, yield a positive result. Recently work has been applied across large and small-scale projects by companies. As these processes develop, ideas and concepts are evolving that active mines, or mines in the early planning stages, could use to help reduce double handling, and in the long run reduce overall project and closure costs, more effectively attain the desired final land use, and enhance the industry’s reputation and licence to operate.CITATION:Leidich, T,?Lacy, H?and Van?Zyl,?M,?2014. Application of design concepts and engineering controls necessary to deliver well-designed and rehabilitated landforms, in Proceedings Life-of-Mine 2014 , pp 55–66 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014