Search Documents

By Wang SS, Frattaroll DR

In the development of novel sulfide collectors, especially for the low-lime and acid circuits, flotation of chalcopyrite, chalcocite, covellite and pyrite was studied with both new and commercially available S- containing collectors. The natural float- ability of sulfides, water quality, and redox potentials - all of which were considered im- portant in assessing collector strength and selectivity - were also investigated. Chalcopyrite exhibited the highest natural floatability. The response to most collectors, however, was chalcocite > covellite > chalcopyrite > pyrite. Water quality had a very significant effect on both natural and collector-aided floatability. De- ionized water and tap water had a flotation suppression effect compared with doubly- distilled water. Flotation results with single minerals are correlated with those for copper and pyrite from natural ores. Several novel collectors have now been developed for sulfide flotation in acid, neutral or mildly alkaline circuits. The results for four of these collectors, which have shown promise in commercial applications, are discussed in this paper.

Jan 1, 1986

Following the Moura No 2 Wardens Court of Inquiry and subsequent changes to the Queensland Mining Legislation there is a requirement in Queensland coal mines for: a person with the recognised competencies to be appointed at each underground coal mine to the position Ventilation Officer; and the person is directly responsible for the implementation of the mine ventilation system and for the establishment of effective standards of ventilation for the mine. The Regulations require that an underground mine must have principal hazard management plans that provide for at the least the following: emergency response, gas management, methane drainage, mine ventilation, spontaneous combustion, and strata control. Other than strata control all the plans require the ventilation officer to have roles and responsibilities to develop, control, monitor and undertake actions in relation to these plans.There are also another 34 Regulations that either directly or indirectly requires the Ventilation Officer to take actions.The purpose of this paper is to outline the information that the regulators look for in sealing plans and the actions the regulators will take if the sealing does not go to plan (TARPs being exceeded).

Jan 1, 2005

Legislation up to the early 1950s prevented the mechanical extraction of pillars. The mines operating at that time had formed extensive areas of pillars. When permission for the mechanical extraction was gazetted, conventional equipment was employed for pillar extraction and generally using hand mining systems. The mid-fifty's saw the of continuous miners. These machines eliminated the disadvantages of conventional equipment and the necessity for multiple working places. Some new layouts for panels emerged; however, actual extraction methods of pillars still followed closely that of hand mining. During the early sixty's the extraction of standing or new formed pillars was undertaken by the "open-end lift" or a "split and lift" method.

Jan 1, 1974

As this district is so far distant from the other mining centres and its mode of approach so circuitous, I am afraid that many residents of other portions of the Commonwealth never think of paying this" Australia's Silver City" a visit, to learn personally the many and various lessons everywhere available, and to become familiar with the really wonderful and interesting features and deposits (which pature has so lavishly bestowed in the mineralogical world) yet seemed to almost ignore or overlook when disposing of topogr,aphical beauties of landscape and vegetation) unless professional or business duties require their presence here. So it is to those whose life is necessarily spent in other parts of the States where they answer their call of duty, and yet feel an interest, either for business or other reasons, that my paper is specially addressed and prepared, and for that reason I witl endeavour to make my remarks more of an explanatory than a dictatorial nature. I feel sure that there. are many members of our Institute who are much more familiar, and have had many more years' experience in the various methods of timbering, filling, and ore extraction, etc., than myself, but I hope that over I6 years' experience in connection with mines and engineering works, the last six of which have been spent in Broken Hill, where, I have been very closely connected.

Jan 1, 1903

How often does one hear that a recent feasibility study was not a success? Alternatively, when scope of the feasibility study was sent out to tender there was a large discrepancy in tendered prices. If the tendered prices were to be compared to the consumer market, for instance the purchase of a car, where the concept is transport in a controlled and safe manner, prices vary by large factors, but then so do the specifications. In the case of a feasibility study, prices should be within a tighter margin as the tenderers are all quoting against the same concept and specification. Why do these discrepancies occur? Price discrepancies will in every likelihood be attributed to two main factors; one, the perceived amount of work and two, the ability of the bidder to carry the risk associated with the feasibility study. It is, therefore, important that the scoping of the feasibility study covers the detailed requirements as clearly as possible stating what level of accuracy is required. The feasibility study is one of the first activities in the life of a project. The study, like the project it is investigating, is subject to the constraints of time, cost and quality. Its primary objectives are to demonstrate the viability of a project within the outlined scope and constraints.

Jan 1, 1998

By Morrison AL

The volume changes occurring during the reduction by hydrogen of single, high-grade hematite pellets under isothermal and non- isothermal conditions were investigated using a time-lapse photographic technique. The major cause of swelling during iso- thermal reduction at temperatures in the range 600-1000¦C, was the disruptive stresses set up during the transformation of hematite to mag- netite. The severity of the disruption was temperature dependent; the degree of swelling increased with increases in the reduction temp erature. Under non-isothermal reduction conditions, in which the pellet temperatures were increased at constant heating rates over the temperature range 500-1000¦C, minor swelling (6-8%) occurred in the initial stages of reduction followed by pellet contractions of up to 15% in the final reduction stages. The low initial swelling and high final pellet shrinkages were due to a com- bination of the temperature dependence of the swelling mechanism, and the sintering of fine pores in the reduced iron in the latter stages of reduction at higher temperatures.

Jan 1, 1980

By Shiels O. J

The major Permian coal deposits of N.S.W. are in the Sydney-Bowen Basin and associated small deposits occur in structurally isolated areas; a further deposit is present in the Oaklands Basin. - The Sydney-Bowen Basin in New South Wales comprises the sub basins, the Sydney Basin and the Gunnedah Basin. Coal measures in these basins are near the top of the Permian succession and within and below an underlying marine sequence. The coal deposits can be conveniently described in units in which the coal geology is homogeneous. The Clyde Coal Measures and Yarrunga Coal Measures contain no seams of economic significance and occur beneath the marine beds in the south of the Sydney Basin. The Greta Coal Measures are economically significant and represent a brief interlude in the marine sequence in the north of the Sydney Basin and equivalents are present in the east of the Gunnedah Basin. The Tomago Coal Measures crop out above the marine sequence east from the Lochinvar Anticline and dip southeast to uneconomic depths. The Newcastle Coal Measures are historically and economically very important and overlie the Tomago Coal Measures and these measures will continue to be important although future mining will be faced with greater depths. To the west of the Lochinvar Anticline the Singleton Coal Measures, equivalent to the Tomago and Newcastle Coal Measures, crop out. This unit represents the thickest development of coal measures in the State and has a very large potential for both open cut and underground mining. Equivalents of the Singleton Coal Measures, the Black Jack Coal Measures and the Booroomin Group crop out on the east side of the Gunnedah Basin and probably are widespread across the Basin. They have less economic potential than the Singleton Coal Measures. In the southwest of the Gunnedah Basin, Illawarra/Singleton Coal Measures crop out over extensive areas and possibly have a large potential for underground mining under low cover. The Illawarra Coal Measures are exposed along the western margin of the Sydney Basin and thicken as they dip into the Basin across a shelf. The outcrop area is currently mined and the shelf has considerable potential for future mining. The highest rank coals in the State are in the Illawarra Coal Measures in the south of the Sydney Basin. The deepest coal mining is in this area and its continuing success is of great importance to the future exploitation of the resources of the Basin. The Tomago, Newcastle, Singleton and Illawarra Coal Measures extend into and meet in the central area of the Sydney Basin but they are under thick cover and are not considered to be economic at present. Permian coal measures occur in isolated areas in the New England Fold Belt and have limited economic potential. The Oaklands Basin in the south of the State contains a large reserve of low rank coal.

Jan 1, 1975

By D Moy, T Carter

This paper outlines the feasibility assessment conducted to explore the possibility of constructing two submarine water supply pipelines beneath the Ma Wan Channel in Hong Kong using either horizontal directional drilling or tunnelling. The Ma Wan Channel is a major shipping channel in the Northwest New Territories, which separates Ma Wan Island from the mainland. The challenges faced by the projectÆs designers included space limitations on either side of the channel, marine department restrictions on construction activity within the channel and selection of a suitable crossing alignment and profile given the channelÆs depth, irregular sea floor topography and complex geology. The existing geological information indicated the proposed alignment would cross granitic and volcanic formations, which would likely be faulted. The primary concerns with horizontal directional drilling were:the length, diameter and depth of the crossing were at the limit of precedent experience in rock; the lack of available space at both the entry and exit sites; and whether the technique would be flexible enough to cope with the anticipated range of ground conditions. The primary concerns for tunnelling were: the possibility of encountering large inflows of high pressure groundwater; andthe possibility of encountering disturbed ground within the fault zones which could flow if not properly treated. As a means to evaluate and mitigate these technical risks for both construction options, a directionally drilled pilot hole was used to investigate the ground conditions along the proposed pipeline alignment. The pilot hole results indicated that either directional drilling or a closed face TBM drive were technically feasible crossing options at a crossing depth of 80 m. The results also indicated that either an open face TBM or a drill blast drive would need to be constructed at much greater depth because of the presence of highly permeable, disturbed ground in mid-channel at this crossing elevation.

Jan 1, 1999

This paper covers the key issues such as orebody geometry and grade, geotechnical data and metallurgical response. These must be considered in selecting a mining system for a new orebody. It then focusses on the advantages of open pit mining over underground mining particularly in the areas of costs, speed of development and safety. Environmental issues with waste storage is the only negative which emerges. Consequently, the majority of new large mine developments continue to be open pits. It is also demonstrated that underground mining continues to play an important role, particulary for high-grade deposits at depth. The impact on ore recoveries of recent developments in stabilised fill technology in underground mining is also highlighted. The importance of economics to the decision on mining method is continually emphasised as maximising orebody value should be the prime objective of this Work.

Jan 1, 1997

It is generally known that Charters Towers was discovered by Mosman, Clarke and Fraser in 1871. However, the time was ripe, and these three were barely in front of others. There is one account that prospectors from Ravenswood visited the area months before but decided it was too far from water, and that one of them had told Mosman and party of the find. There is another account that Joe Larkins found the discoverers before they had registered any ground - this may explain Mosman's quick departure for Ravenswood.When the news spread, the rush was rapid, and there was soon a sizeable population: probably too many, as within twelve months the infant settlement was under considerable stress. First, the presiding Gold Commissioners had adopted "unusual and arbitary" interpretations of the Regulations, and many of the miners were aggrieved; Charters, the senior Commissioner, was accused of favouring moneyed interests, and of retiring ill whenever a brawl or confrontation occured. As a result, the law of the field soon became "the survival of the strong". Second, the settlers were, divided on where the main town should be: Millchester, near the water, or Charters Towers near the mines. Third, the discovery of gold at the Millchester Deep Lead in August, 1872 was followed by highly exaggerated accoants in_' the southern papers, apparently fabricated by local business speculators. The resulting rush resulted in hundreds of unlucky prospectors having to return or seek other fields. In that period two men were killed in squabbles over ground. To make matters worse, by October 1872 a drought had set in, water cost three pence a bucket, fodder was scarce, cartage expensive, and the price of crushing ore rose to thirty shillings per ton.

Jan 1, 1986

By Kubo H, Ninomiya R, Ojiro T, Sato T

New high-strength Zn alloys for moulds are demanded from the automobile and electric industries in Japan, because the s rength of Zn moulds is still not high enough for the mass production. There are two approaches to improve the strength of Zn alloys. One is to increase the Al content. ZA alloys (ZA-8, ZA-12, ZA-27) were developed through this approach. The other is to increase the Cu content. But it is known that an increase in Cu generally depresses the castability of Zn alloys, so that the alloys with increased Cu have been rarely studied until now. In this study a reconciliation between the strengthening and the castability of Zn alloys by enriching both with Al and Cu has been attempted. Accordingly we have studied on the Zn alloys containing 4 to 25 mass per cent Al and to 24 mass per cent Cu have been studied. Their fluidity, which primarily corresponds to the castability of the alloy, were measured first and 19 alloys were selected based upon their fluidities and casting temperatures. Mainly the mechanical properties of all 19 alloys were tested and some were found to be excellent in both strength and castability. Z1009 (Zn-IOAI-9Cu-0.02Mg alloy) cast in a sand mould has the tensile strength of 360 MPa while ZAS (Zn-4AI-3Cu-0.04Mg alloy), which is the most popular alloy for moulds, is 215 MPa. Z2520 (Zn-25AI-20Cu-0.02Mg alloy) cast in a sand mould has a Vickers hardness of 178, compared to 107 for ZAS and 104 for ZA-27 (Zn-27AI-2Cu-0.02Mg). Furthermore the castability of Z1009 is as good as that of ZAS. The underside shrinkage occuring in casting ZA-27 is restrained in Z2520.

Jan 1, 1993

By C Mpodozis

Central Andean (22¦S to 34¦S latitude) Miocene giant ore deposits share common features that reveal their origin. Tectonic and magmatic features include a relation to a shallow subduction zone, an association with the waning or initiation of a magmatic episode, emplacement at the time of uplift associated with crustal thickening and formation at times of major magmatic changes along the Andean margin. Rare Earth Element (REE) signatures in magmas erupted near the time of mineralisation indicate a progressive change from equilibration at depth with a hydrous, intermediate-pressure amphibole-bearing mineral residue to equilibration with an anhydrous high-pressure garnet-bearing assemblage. These features point to a common history. First, a relatively shallow subduction zone leads to hydration of a cool mantle wedge providing a source of fluids which builds up over at least several million years. Arc magmas formed at this time equilibrate with a hornblende-bearing residual mineralogy. Second, a compressive tectonic regime leads to crustal shortening and thickening that facilitates entrapment of arc magmas in the crust. Eventually, the magma-weakened crust yields to horizontal compression causing rapid crustal thickening. Fluids required for mineralisation are liberated as amphibole-bearing assemblages break down to garnet-bearing ones and over pressured fluids are released from plutons. Mineralisation subsequently ceases in the region unless continued dehydration of the slab and mechanical thinning of the continental lithosphere causes the previous conditions to repeat. The type of mineral deposit generated depends on the pre-existing continental lithosphere and the distance from the trench.

Jan 1, 1999

By Stewart R, Manson RA, Haig DW, Perembo RCB, Kruman B

Since the advent of plate tectonic modelling, the Ramu-Markham valley has been thought the site of a classical island-arc/conti- nent collision zone. In this interpretation the units south of the Markham Valley are held to be island are / micrcontinental mate- rial accreted to Australia and those north of the valley are thought to represent a separate Finisterre island-arc terrane. Recent remapping by the Geological Survey of Papua New Guinea shows: (1) there is no terrane boundary along the Ramu-Markham valley (2) the Finisterre Volcanics are probably part of either a fore-arc sequence or oceanic plateau obducted onto a microcontinent/ volcanic-arc composite terrane, accreted to the continental Australian plate. A new tectonic model is proposed for northern PNG and involves: (I) Eocene to Late Oligocene subduction below a microcontinent remote from Australia to produce the Sepik are and related intrusives, the Finisterre Volcanics (fore-arc or possible oce- anic plateau), together with the Alife blueschist. (2) obduction of the Sepik arc in Late Oligocene-Early Miocene times over the advancing Australian plate. This resulted in crustal melting, some of the products of which are the Mid- dle to Late Miocene Akuna and Bismarck intrusive complexes of the Maramuni arc. (3) obduction of the Finisterre Volcanics began in Early Pliocene times and continues today. (4) post-Middle Miocene mineralisation is the result of melting after obduction of the Sepik microcontinent.

Jan 1, 1997

Standards in the public reporting of resources and reserves in Australia have dramatically improved since the implementation of the Australasian Code for Reporting of Mineral Resources and Ore Reserves (The JORC Code) in 1989. Whilst the JORC Code states clearly that Mineral Resources and Ore Reserves are imprecise calculations and should be treated as estimates, there is strong evidence that many people regard them as fact, including some accountants, directors, auditors and investors. Mineral Resources and Ore Reserves are key inputs in the valuation of a mining company and the determination of financial performance. Geological knowledge is the foundation upon which Mineral Resources, Ore Reserves and investment decisions are made, however this information carries with it substantial uncertainty. Case studies and company reports have established that errors derived from inadequate geological inputs have led to reduced profitability in operating mines and in extreme cases the premature closure of mine operations. Whilst there are many causes of mine closure and reduced profitability, including commodity prices and exchange rates, the cumulative effect of all geological uncertainty contributes significantly to the erosion of the credibility of mining within the investment community. There are a number of methods used to characterise and model uncertainty in Mineral Resource and Ore Reserve estimation. Empirical mining indexes, sensitivity analyses, Monte Carlo simulations and Conditional simulations are used to identify and estimate geological uncertainty, notably the quantification of uncertainty in grade and tonnage estimates. These techniques have not generally been applied to estimating geological uncertainty associated with key Ore Reserve inputs such as appropriate mining technique, equipment selection, production rate, mining dilution, stability requirements, materials handling, metallurgical processing, product quality and waste storage. New software tools are needed to model the entire mining process with all its geological and other interdependencies, enabling all uncertainties to be separately identified and estimated. By its very nature, mining involves the assumption of significant technical, financial, political, environmental and social risk. Success comes by understanding and managing these risks and consequently the mining industry will never choose to reduce the level of geological uncertainty to nil. The ultimate aim of improved identification and estimation of geological uncertainty is to quantify inputs into the Ore Reserve process, allowing a company to assess the risks and manage these accordingly. This approach is relevant to feasibility studies for new projects as well as life-of-mine planning through to the weekly schedule at existing mines.

Jan 1, 2003

By Skinner W, Netting A. K O

Surface analysis of ore samples collected from corresponding concentrate and tailings process streams is now a widely used tool in many Australian base metal sulphide concentrators, particularly those involved in AMIRA projects. The use of tec

Jan 1, 1997

In recent years new instrumentation and digital technology have Wrote possible a new facet of goo-physics: broadband seismology. From digitally record-ing networks and arrays. broadband scistnograrns of body waves that are flat to displacement and veloc-ity in at least the frequency range from 0.01 to 5.0 liz can now be routinely obtained for most carthquakes of magnitude greater than about 5.5. In contrast to data from conventional narrowband seismographs, broad-band body waves have sufficient spectral information to nvest,igate the many frequency-dependent eflects that may arise from source finiteness and from wave prop-agat ion phenomenon. Besides the usual parameters of depth. moment and focal mechanism, broadband data have sufficient spectral information to provide estimates of radiated energy, associated stresses and the frequency dependence of source parameters. Moreover. teleseis-mically recorded broadband data and near-field strong motion accelerograms overlap in the frequency band be-tween about 0.1-2.0 Hz. Thus. v it h broadband data it is possible to connect far field and near field data in order to make estimates of acceleration for almost any seismically active region of the circum-Pacific.

Jan 1, 1990

Risk Management has been applied relatively slowly in the mining industry. Except for the risk concept application in financial considerations, the application of Risk Management in safety management has been far from satisfactory. When applied it was treated in a global occupational safety and health sense. Regardless of how much the mining industry has progressed over the years it is still, in many respects, `state-of-the-art' business. The safety aspects of mining are well known and yet little understood by the public. Regardless of what has been achieved so far and how much effort has been put into it, mining is regarded as an unsafe and somehow rude business. Safety records of the mining industry vary from State-to-State. Latest mining related disasters in PNG and Queensland and some other fatal accidents support this public perception. They purport a need for change in managing safety in the mining industry. The latest mining fatalities have raised the issue: What must be done to improve safety standards? Duty of care, risk management and system engineering concepts can provide some answers. Risk Management principles which have been advocated for some time provide many answers and explanations and can make safety management more constructive and workable. What has been missing so far is that this concept has neither been applied nor has been modified for its practical application and purpose on a larger scale. A risk management approach to the management of safety and health in the mining industry is addressed, herein. This approach does not attempt to provide the solution. It does, however, provide a basic understanding of what Risk and Risk Management are all about. Rational management of risk is addressed in the life cycle and system contexts. A system of continuous improvement is applied. There is always a chain of events, outcome, exposure, consequence(s), and consequence(s) value(s). It means that development of an event takes place in time and space. Dynamic circumstances have been created in or within the system. It is a decision-making process designed to provide a methodology which is directed not toward a mathematical model but toward easy use and application in dynamic working environment, by decision-makers who can be anybody from either a risk taker or a risk creator. The emphasis is placed not only on arriving at the best practical, possible and fair decision but also on structured and systematic acquisition of knowledge about the system, its hazards and associated risks, hence increasing the decision maker's ability to manage the decision-making process related to the management of risk.

Jan 1, 1995

By C Li, K McDonald an, T Nicholson, C Brown

The relative reactivities of chars prepared from different coal samples at temperatures in the range 500 to 1150¦C were determined by measuring the rates of metallisation of a standard ilmenite concentrate. The results have been interpreted in relation to different measured physical and chemical properties of the chars. Char reactivities were found to correlate with the maximum specific surface area (SSA) of the chars, obtained from plots of SSA versus temperature. Weathering of coal samples gave higher reactivities which correlated with higher SSAs. Experiments using recycled chars showed that the high internal SSAs developed during earlier reduction reactions provide no benefit in terms of increased metallisations. The important role of char hydrogen contents in controlling low temperature metallisation rates was demonstrated. Chars prepared from different rank coals had the same hydrogen content when prepared at the same temperature. Ilmenite metallisation rates had a linear dependence on the hydrogen content of the chars. Large differences in the slopes of the metallisation versus H2 content curves for different chars were interpreted in terms of SSA variations and catalysis of the gas reactions by dispersed metallic iron particles in the chars. A simple test based on magnetic separation of the char was shown to give an indication of enhanced reactivity due to contained metallic iron.

Jan 1, 2001

By M Henderson, M Hudyma

Mining-induced seismicity at Junction Gold Mine became a serious operational problem in the late-1990s. Assessing the local seismic hazard is an important step in assessing the risk associated with potential rockbursting. This paper discusses the qualitative and quantitative means of assessing seismic hazard used at Junction. In qualitative hazard assessment, the role of the primary factors contributing to mining-induced seismicity and rockbursting are identified. These factors include: rock mass properties, geological structures, mine development, and stoping. A qualitative seismic hazard map has been developed considering these factors. In quantitative hazard assessment, seismic source parameters from an Integrated Seismic System are used to assess seismic hazard. The seismic source parameters found to be relevant to seismic hazard assessment at Junction are discussed.

Jan 1, 2002

By Pattinaja MA

Mathematical modelling was carried out to determine the probable convergence and vertical stress patterns around a retreating longwall panel in an underground coal mine in New South Wales. An 'Electrical Resistance Analogue' and a program called 'THREED' based on the displacement discontinuity method were used for the modelling. Parts of the obtained results are presented here and compared with some measurements of convergence at the site. The modelled and measured data agree better qualitatively, than quantitatively.

Jan 1, 1986