Search Documents

By R H. Sibson

Magmatic and/or hydrothermal fluid systems in island or mountain arcs self-organise to critical states subject to perturbation by changes in the regional stress, which plays a controlling role in the containment of overpressured fluids. Whether the magmatic arc is under compression (eg Andes, northern Honshu) or extension (eg Taupo Volcanic Zone, New Zealand) is a key factor controlling the ease of magmatic or hydrothermal fluid ascent. Abrupt changes in the stress regime have the potential to induce major episodes of fluid redistribution. Large earthquake ruptures along plate boundaries may induce such changes over broad areas, also contributing to fluid redistribution by renewing fault permeability along the causative rupture zone or reactivating distant fault-fracture permeability by shaking from radiated waves. High-resolution geophysical investigations of active arc systems and the subduction thrust interface underlying their fore-arcs reveal repositories of overpressured hydrothermal fluids. In active magmatic arcs under compression such as NE Honshu or Cascadia, there is evidence for a heterogeneous distribution of overpressured hydrothermal fluids in the middle-to-lower crust trapped around the base of the upper crustal seismogenic zone. Investigations of the subduction thrust interface responsible for great (Mw = 8.0) ‘megathrust’ earthquake ruptures has revealed in some instances (Cascadia, SW Japan) the existence of a belt of non-volcanic tremor (NVT) with accompanying slow slip episodes defining the base of the megathrust interface at 40 ± 5 km and 350°C??-??550°C. Aqueous fluid at these depths is likely derived from dehydration reactions accompanying the basalt-eclogite transition in subducted oceanic crust. NVT sequences in the hanging-wall above the interface may be defining migration pathways into the overlying crust.The potential for eruptive episodes in magmatic arcs and redistribution of hydrothermal fluids is assessed in the light of the stress changes that followed the 2011 Mw9.0 Tohoku subduction thrust rupture which extended along strike for over 500 km and down-dip for over 150 km, with maximum slip of c 50 m.

Aug 22, 2011

By N Winkelmann

Underground coal heating is a significant hazard in some coal mines. The broad principles of how underground coal heatings occur is reasonably known, however the technique for locating the heatings in often inaccessible goaf has been proved to be difficult. Since 2002, CSIRO, with the support of the Australian Coal Association Research Program (ACARP) has been undertaking investigations to apply and develop innovative surface-based radon technique for locating the underground heatings in Australia. This paper presents the progress of the investigation.

Jan 1, 2005

By J Hutchings

An essential component to the management of any process is the measurement of key parameters, used to monitor, control, and provide the feedback necessary for improvement. This paper discusses how data collection and analysis can provide a better understanding of the blasting process, as well as additional control and improved outcomes.The drill and blast process involves the generation and use of information at a number of levels. Comparison of historical parameters and results provides a starting point for the development of ongoing blast designs and a baseline against which future results can be compared. The collection of data during implementation provides a quality assurance/quality control (QA/QC) function where potential defects (such as under-drilled or over-charged holes) can be rectified prior to firing. Actual quantities and production rates allow the development of realistic plans and schedules, rather than using inaccurate estimates and targets that lead to unscheduled changes to equipment paths. Over?the past several years there have been a number of technological advances in data collection technology. Drill monitoring instrumentation on blasthole drills provides location information and feedback on rock properties as drilling occurs. Hand held ‘data logger’ technology has also overcome the challenges of working on the bench, such that blasthole measurements can be collected and forwarded directly to the explosive truck. Mine sites are becoming wireless network-enabled allowing the seamless data transfer from the field back to the office, in near real time, as that information is collected. Great strides have also been made in the development of drill and blast software systems which are more user friendly, and yet provide far greater capability to manage the quantity of data generated. The blasting process is critical to the overall mining process and the delivery of a successful blast outcome requires that the blasting process be ‘in control’. The measurement of key parameters can provide the data with which to measure and maintain control of blasting, and allows the validation of performance improvement measures and identification of improvement opportunities.

Nov 8, 2011

By R Wolff

One critical factor in open pit mining projects is the estimation of the recoverable reserves. The reason for this is that at the valuation stage there is a lack of information about future metal prices and production costs. Consequently, the estimation of the recoverable reserves needs to be done based on a fixed break-even cut-off grade (BECG), in which fixed expected metal prices and production costs are assumed throughout the operating life of the mine (OLM). In this paper, an alternative technique for estimating the recoverable reserves of an open pit mining project is presented and explained in detail. The main characteristic of this technique is that it estimates the recoverable reserves of the project using mining costs as reference: this is done due to the fact that mining costs are easier to model than metal prices. Another important characteristic of this technique is that it uses the uncertainty of the geology of the orebody, given by simulations of the deposit, to make final strategic decisions, such as the selection of the operating life of the mine and the optimal production rate, which minimise the risk of not achieving future production targets while maximising the upside potential of future rewards. As it will be shown, the final outcome of the proposed technique is the generation of a robust open pit design, that include cutbacks and ultimate pit limits, called the marginal open pit mine design (MOPMD). One characteristic of the MOPMD is that, at each production period, it will be characterised by their respective geological uncertainty, given as probability distributions of ore, waste and metal quantities, and by marginal economical project indicators, such as cut-off grades and metal prices, among others. The details follow in the paper.

Jan 1, 2006

By V Novoselov, R Sabirov

Flotation processing technology of water-soluble minerals has made it possible to realise, since the 1960s, the wide scale industrial processing of potash and potassium-magnesium ores (about 200 million tonnes per year) as well as to create the multi-tonnage worldwide production of sylvite (KCl) for industrial and agricultural application. In this paper the particularities of the effect of reagents (blinders, collectors and frothers) during cation flotation in saturated saline solutions are outlined. New reagent modes for activating the effects of alkylamines during the flotation of KCl and the perfecting of technological flow sheets for processing potassium ore have been developed. The results of research on the reverse flotation of carnallite ore, with the help of alkylmorpholine û a new developing technology for benefication carnallite as raw material for the production of metal magnesium and fertilisers are listed. Examples are given of the industrial applications of processed reagent modes at potash flotation factories in Russia.

Jan 1, 2005

By Muldoon T

Water sprays on mining machines are generally put there to reduce dust; however, research by the Bureau of Mines and others has shown that considerable airflows may also be generated by these sprays. This recognition of water spray-gen- erated air movement led to the "Spray-Fan" - a continuous miner auxiliary ventilation system which was shown to reduce methane peaks by a factor of 15. Recent successes and failures of the Spray Fan are reviewed. More recently, the same principles were used in the design of the "Shearer- Clearer" for reducing dust at longwall shearer operators. The original design was successful; however, a new design is now available which is more practical to install and does a much better job of holding the dust against the face downwind of the shearer. The latest research objective is to eliminate the negative impact of spray- generated air turbulence on continuous miner dust control. Most coal faces in the USA are ventilated in the exhaust mode using "line curtain", and the forward airflow on the side of the heading opposite the curtain is inevitably weak. Air turbulence generated by sprays which are incorrectly located and/or operated at excessive pressures can cause roll back - in which the dust cloud at the face is forced unwind against the ventilation and spreads over the miner cnerator. The general approach to reducing "roll back." is reviewed and art anti-roll back water spray system is presented.

Jan 1, 1983

By I R. F MacCulloch

Bacterial oxidation of sulfide minerals is a familiar and commercially available process to enhance gold recovery with problem ores. Pintail Systems, a Colorado, USA based company had developed bio-processes for gold recovery based on natural mineral formation and transformation in a global mineral cycle. The biological recovery of precious metals from ore involves a number of mechanisms that are dependent on the metal-mineralogical association. These processes include: partial bio-oxidation of sulfide ores; oxidation of gangue minerals exposing gold to leaching; surfactant properties of bacteria/nutrient solutions that improve wettability of ores and solution contact with leachable gold and silver; and microbial production and excretion of trace amounts of gold lixiviants, and bio-fracturing or biological alteration of ore minerals. Pintail has demonstrated enhanced recovery of precious metals during cyanide detoxification of spent heaps at the end of mine life. Biological recovery processes also have the potential to be applied to in situ mining technologies. The in situ process application could recover gold from subgrade deposits, small deposits or those ore bodies with uneconomic stripping ratios for conventional mining. In situ biomining can be accomplished at a fraction of the cost of conventional mining and leaching and does not have the environmental liabilities associated with many conventional gold lixiviants.

Jan 1, 2004

By R L. Brathwaite

The rocks of New Zealand can be grouped into three main elements: the Early to Mid Paleozoic Western Province, Late Paleozoic to Early Cretaceous Eastern Province, and several overlying Late Cretaceous to Cenozoic sedimentary basins. The Western and Eastern provinces were formed on or near the margin of Gondwanaland, whereas the Late Cretaceous to Cenozoic sedimentary basins developed after the separation of New Zealand from Gondwanaland in the Late Cretaceous.   The Early to Mid Paleozoic Western Province rocks are exposed in Nelson, Westland and Fiordland and include metamorphosed sandstone, mudstone, limestone, and volcanic rocks, intruded by granite batholiths and maficultramafic igneous complexes. The main associated mineral deposits are gold-quartz lodes hosted by Paleozoic greywacke and argillite. Other type of deposits present include: volcanogenic massive sulphide lead-zinc; vein and greisen tungsten and tin; and magmatic nickel-copper sulphide, platinum group element, and magnetiteilmenite deposits. Granite stocks and batholiths, intruded during the Cretaceous, have associated porphyry molybdenum deposits.   The Late Paleozoic to Early Cretaceous Eastern Province includes the greywacke rocks forming the axial ranges of the North and South islands, and a belt of schists in Marlborough, the Southern Alps and Otago. The schists host many shear-zone related, gold-quartz lodes and, in the Southern Alps, lenses of serpentinite with talcmagnesite and nephrite jade. Volcanogenic massive sulphide copper deposits and volcanogenic manganesechert deposits, occur in both the schist and greywacke, and a belt of Permian age ultramafic rocks (Dun Mountain Ophiolite) has associated copper, chromite and chrysotile asbestos deposits.   The Late Cretaceous to Cenozoic rocks are found in a number of sedimentary basins onshore and offshore of the North and South Islands. Many of these basins developed during the rifting of New Zealand from Gondwanaland in the Late Cretaceous. They contain New Zealand's economic petroleum, coal and limestone deposits. Uplift and erosion of the mountain ranges shed gold into rich placer deposits in the South Island.   From the Miocene, volcanic rocks feature prominently on the eastern South Island (e.g. Banks Peninsula southeast of Christchurch and the Otago Peninsula northeast of Dunedin) and northern North Island (Northland and Hauraki), and volcanism continues today in the Taupo Volcanic Zone. The North Island volcanic rocks have associated epithermal mineralisation, mainly gold and silver, but also copper, lead, zinc, mercury, and antimony, as well as deposits of sulphur, perlite, pumice and zeolite. Porphyry copper style mineralisation is associated with subvolcanic intrusive rocks. Erosion of the volcanic rocks has shed titanomagnetite onto the west coast of the North Island forming significant coastal placer deposits. Similarly, erosion of the Alpine schists in the South Island has resulted in placer ilmenite deposits on the coast of Westland.

Jan 1, 1997

Many persons hold the opinion that the metal indus- ries are fortuitous and that the occupation is one of sordid toil, and altogether a kind of business requir- ing not so much skill as labour. But as for myself, when I reflect carefully upon its special points one by one, it appears to be far otherwise. So wrote Georgius Agricola in 1556. He could have been espousing the sentiments of an indus- trial archaeologist investigating mining sites in 1986. South Australia has a very rich legacy from its industrial past-especially in the area of its mining history. Industrial archaeology, which is part of the broad field of archaeology, is concerned with the material and documentary remains of this industrial past. This includes the products and processes of manufacturing, industrial, technolog- ical and engineering activity and their relation- ships to people and the environment. `Archaeology' immediately conjures up the image of excavations in Greece or Eygpt. Excavation however is only a part of archaeological methodology. Industrial archaeology utilizes documentary historical rec- ords combined with field survey techniques (both above and below ground) to create a composite picture of the past. Interest in our recent past has burgeoned in Australia in the last few years. This interest manifests itself in many ways-the unprecedented popularity of Australiana and col- lecting, the plethora of Australian historic films, the growth of the National Trust, local historical societies and genealogical research. Fortunately these trends have been reflected in academic and legislative circles. Various univers- ities, institutes of technology and colleges of advanced education run courses in aspects of cul- tural resource management and conservation of the historic environment. These courses are com- prised of archaeology, architecture, geography, his- tory, materials conservation, museum studies, and national parks management and planning.

Jan 1, 1987

By R G. Reddy, A Yahya

The sulfur distribution ratio (Ls) is an expression of the amount of sulfur in slag to the amount of sulfur in molten metal. The sulfide capacities calculated from Reddy-Blander (RB) model were used to calculate the sulfur distribution ratio (Ls). A new Reddy model for sulfur distribution ratio (Ls) was developed for modelling Ls for ironmaking, steelmaking, and secondary steelmaking conditions. Besides calcium oxide, the major component in the ladle furnace (LF) slags is alumina. The Ls was calculated for typical LF slags as a function of temperature and composition. The model calculated Ls values are in good agreement with the experimental and industrial slags data. The extremely low oxygen potential in these furnaces after fully-killed steel is favourable for desulfurisation. For any given slag’s composition and temperature, its sulfide capacity can be calculated a priori. The equilibrium sulfur distribution ratio between this slag and liquid metal in a particular vessel can also be calculated a priori. The Ls for ladle furnace (LF) slags is about twice those for blast furnaces (BF) slags and ten times those of basic oxygen furnace (BOF) slags. The desulfurisation of pig iron in BF and desulfurisation of steel in LF during secondary steelmaking are recommended. Steel desulfurisation in steelmaking furnaces is not effective. Since the model used to calculate the sulfur distribution ratio (Ls) is a priori, it is a useful tool for the iron and steel makers in improving the product quality and optimisation of the industrial furnace operations.

Aug 21, 2024

By Robertson K. S, Hunter T. C

AEG-Elotherm's electromagnetic dosing channel, or Eldomet, is a recent invention enabling the transport and metering of molten metals. The development of a reliable refract- ory lining, and the use of suitable construct- ion and operating techniques has led to the successful application of the Eldomet for casting copper anodes at Copper Refineries Pty. Ltd.

Jan 1, 1974

By A Castleden, G Cavanough, M Kochanek, J Cunningham

ROES« is a proposed new mining system for underground hard rock mines. Ore is accessed from within a shaft, which is located close to or within the stope, and pitched either vertical or within approximately 20 degrees of vertical. The shaft is designed to exclude personnel entry so production drilling and explosive placement is done using remotely controlled or automated machines. Routine remotely controlled survey of the shaft, stope back and broken rock within the stope is typically done following each blast. The survey may include excavation geometry, rock fragmentation and geotechnical characteristics. Blastholes are surveyed before placement of explosives. This provides mine operators and engineers with real-time data, allowing them to monitor production performance and risk factors so that they can make rapid changes as required. ROES« is designed to apply to open stoping or sublevel caving situations either in disseminated, geologically defined, thick tabular or narrow vein orebodies. The technologies developed for ROES« will also have potential applications to block caving operations to reduce the risk of frozen ore and poor fragmentation. In a typical sublevel open stope application, ROES« will reduce the amount of stope-associated development by about half and therefore will allow ore to be brought on-stream sooner and at significantly reduced cost. Other savings are expected to flow from the centralisation of mining activities and operational data, reduction in mining fleet, reduction in ventilation requirements, improved occupational safety and reduced mine complexity. CSIRO and Orica Mining Services are developing the required technology and AMIRA is seeking sponsorship for a project to trial the mining method. This paper details the ROES« method, expected benefits and applications and includes typical stope and mining block designs and design requirements.

Jan 1, 2008

By S N SHEARD

The use of geophysics in mineral exploration in Australia, and overseas, has increased dramatically over this century. This paper shows that using simple equipment with clever interpretation that the foundations of modem geophysics were laid, using all the same principles. The plethora and diversity of mineral exploration geophysical techniques does not allow a full description of their evolution to be given in such a paper. To convey this evolution, however, the progress of two different geophysical methods, magnetics - a potential field (passive) method, and electromagnetics - an electrical (active) method, are described. Examples of magnetic survey data from the 1920s and more recent vehicle home and airborne surveys are given to show the increase in data quality through technological improvement. A set of four airborne electromagnetic data sets spanning three decades is used to indicate the improvement in electromagnetic techniques. It is argued, that considerable progress is still required in the electromagnetic field to increase its interpretability.

Jan 1, 1992

During the 1950's there was a flurry of activity on the design of main ventilation shafts for mines. More recently, a new ana- lysis was commissioned in relation to the multi-shaft, nuclear waste isolation facili- ties currently under design in the United States. This paper presents the major find- ings of that study and should prove of value as a reference in the design of proposed new shafts. An overview of mine shaft resistance introduces the effects of the shaft walls, fittings, conveyances and shaft stations. Each of these is analyzed in turn. A com- pletely new technique is described, which facilitates the estimation of wall resis- tance. The effect of size of a conveyance is quantified and shown to be dominant when the cage occupies more than 30 per cent of the shaft cross-section. The dynamic effects of a moving conveyance are also analyzed.

Jan 1, 1988

By M Norbert, P Mok

The mainline running tunnels for Legacy Way comprise of two-lane tunnel boring machines (TBM) driven tunnels. The length of the TBM tunnel section is approximately 4.2 km. The TBMs employed are double shield TBMs. Typical support to the segment ring while advancing a double shield TBM comprises of filling the excavated annulus between the ground and the segmental lining by injecting pea gravel, followed with primary grouting to fill between the pea gravel some distance behind the excavated face. The methodology adopted for the Legacy Way project, however, did not follow this typical approach, instead, two component grouting of the annulus was carried out.Where the annulus is typically filled with pea gravel, support is provided to the segment ring very close to the end of the tail shield, whereas in the case of two component grout this is not practical as the risk of grouting in the tail shield is high. The staging of the two component grout injection, the grout early age strength properties become key issues in ensuring that the segment ring leaving the TBM tail shield is stable and can support the necessary external loads.Two-component grout is a grout with two components, cementitious grout (component A) and accelerator (component B), commonly adopted for earth pressure balance (EPB) TBM. The grout reaches its thixotropic state in a matter of seconds providing initial support for the segment rings. Manual injection of two component grout to fill the bore annulus was carried out in stages leaving a portion of the segment rings unsupported. Ring stability during TBM advance was provided by a combination of ram thrust and the segment circumferential joint shear connectors.This paper outlines the design considerations such as rock load derivation by probabilistic analysis carried out utilising the software JBlock, 3D finite element analyses using the software Strand7 for ring stability and the testing and back analysis of the shear connector load bearing behaviour. In particular, the actual available capacity of the shear connectors against their published capacity by supplier was discussed.CITATION:Mok, P and Norbert, M, 2014. Tunnel boring machine excavation stability – double shield tunnel boring machine advance with partially grouted annulus, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 51–62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By P Hatherly, H Gurgenci

With the depletion of the mineral reserves that can be mined by surface mining, demand for highly productive and safe underground mines will increase. Underground drill and blast techniques continue to be refined but true æmass productionÆ is difficult to achieve. As is evidenced by the longwall mining of coal, alternative mining methods based on mechanised mining can meet the expectations but the issues of how to effectively cut strong rocks, how to define the orebody and how the mechanised miners can be automated and maintained all need to be addressed. CMTE is working in all of these areas. We believe that the oscillating disc cutter may provide the long sought-after breakthrough in mechanised rock cutting. Disc cutters are one of the most robust designs of cutting tool and the cutters attack the rock in a manner which effects direct tensile breakage. The internal cutter drive and the inertial damping mean that the already low cutter forces are not all transmitted back to the machine, making it possible to design lightweight, flexible mining systems. For orebody delineation drill monitoring, drillhole logging and geophysical imaging are key procedures being developed at CMTE. To automate mining machines, work is progressing well in the development of systems for autonomous vehicle navigation and mining robotics. A strategic contribution to maintenance issues is being made through the development of procedures for automatic analysis of used oils, monitoring the strength of mechanical structures, and operating point optimisation.

Jan 1, 1998

The 1990s present many challenges, not the least of which is in the area of health and safety. Integrating of safety and health into the management process to suit the overall needs of a company will require commitment. Organisations which consistently perform to high success levels do so because they plan it that way. By using tools of total quality management, the potential to continually improve all safety processes exists. The successful integration of total quality measurement principles used in the improvement of safety processes, and the measurement of performance-based activities allow for prevention of accident causing scenarios and performance improvement.

Jan 1, 1993

By W Newton, J Price

This paper outlines the design, justification and performance of a gravity circuit upgrade at the Marvel Loch treatment plant. The design of the upgrade was simple but effective. The key components of the upgrade were the addition of a sluice and a second Knelson Concentrator. The sluice was installed as a pre-concentration step. The upgrade also included the purchase of a Mineral Cone to treat the increased quantity of gravity concentrate. The cost was low because of the use of mostly second-hand equipment. The result was that for a cost of $75 000 the gravity recovery doubled and the overall recovery increased by over one per cent. This paper shows that you do not need to spend millions of dollars to be innovative and successful.

Jan 1, 2000

By W D. Erskine, M J. Saynor

Ranger Uranium Mine, surrounded by Kakadu National Park is located in the Alligator Rivers Region (ARR) in the wet-dry monsoonal tropics, 250 km east of Darwin, Northern Territory. A trial landform (TLF), measuring approximately 200 m by 400 m (8 ha) was constructed during late 2008 and early 2009 by Energy Resources of Australia (ERA), adjacent to the northwestern wall of the tailings storage facility at the Ranger Mine. A collaborative research program involving the Environmental Research Institute of the Supervising Scientist (eriss) and ERA, has been underway to measure long-term (five to ten year) rainfall, run-off, sediment and solute losses, seepage and vegetation establishment on the TLF (Saynor et al, 2012; Lowry et al, 2014). This paper reports on bed load losses from four erosion plots built on the TLF. These were achieved by physically isolating approximately 30 × 30 m areas from the surrounding landform on three sides with sidewalls along with an open polyvinyl chloride (PVC) pipe on the downslope side. Each plot was instrumented with a range of sensors. Two plots, 1 and 2 were constructed on waste rock material, while plots 3 and 4 were constructed on waste rock mixed with approximately 30 per cent lateritic material. Plots 1 and 4 had tube stock planted in early 2009, and plots 2 and 3 were initially planted by direct seeding in July 2009 and were infill planted with tube stock in January 2011.CITATION:Saynor, M J and Erskine, W D, 2016. Bed load losses from experimental plots on a rehabilitated uranium mine in northern Australia, in Proceedings Life-of-Mine 2016 Conference , pp 168–171 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Moylan T, Stewart D

A case study examining the procedures and financial benefits of introducing dump leaching to augment the Mt Gibson Gold Project CIP operations is discussed. Metallurgical testwork, followed by pilot dump leach operations, confirmed that gold recoveries of greater than 60 per cent could be achieved by dump leaching Mt Gibson laterite ore. Capital and operating costs were determined. Pit optimisation using the Whittle FOUR-D optimisation program calculated an optimum cutover grade between CIP and dump leaching for one orebody. The resultant recalculation of reserves based on CIP and dump leach operating costs showed that reserves for that orebody could be increased from 329 000 tonnes at 1.9 g/t An, to 1 488 000 tonnes at 1.2 gh An. NPV for the CIP only option of $1.4 m, was increased to $4.0 m for the combined CIP/dump leach option. This technique can be applied to existing gold projects and to new Developments.

Jan 1, 1992