Search Documents

By P. K. Foh, C. G. Dunn

IN an investigation of the rolling and recrystalliz-ing textures obtained from single crystals of Si-Fe, Koh and Dunn included specimens in the (111) [lie] orientation.1,2 This note reports some additional results obtained on samples of this orientation set aside for further study. After, primary recrystallization longer annealing treatments at 980°C produced only normal grain growth; after 16 hr at 980°C the largest grains were approximately 0.010 to 0.020 in. in diam. The orientations of 13 of the larger grains were found by the transmission Laue method. The unidentified (110) poles of these grains have been added to the (110) pole figure obtained after primary recrystallization2 to give the plot shown in Fig. 1. When grain identifications are also included, such a plot reveals the following. Two orientations agree almost exactly with the peak pole ,density positions of component B of the primary recrystallization texture, one with component A, and one with component C. All the remaining orientations except one have (110) poles near weaker and unidentified pole density peaks. In fact, the correlation is good enough for an identification of eight components. Previously only components A, B, and C were certain. The results are perhaps even more informative when combined with the (110) pole figure of the cold-rolled crystal to give the plot shown in Fig. 2. Each of the 13 orientations is identified and uniquely determined by selecting two (110) poles per crystal, which are 90" apart. The plot shows that every grain of the 13, except grain 6, has a (110) pole in common with a (110) pole concentration of the cold-rolled crystal. The orientation relationship with the cold-rolled orientation may be expressed as approximately 25" rotations about <110> axes, which is in agreement with the results found for coarse-grained primary recrystallization.2 If primary recrystallization had occurred according to the <110> rule without preference, there would have been 12 components. Actually our limited data reveals nine of the possible 12. The integrated pole figure also shows preferences among them, since three are considerably stronger than the rest. In addition to the above direct information, the following conclusions may be drawn. Primary recrystallization of the (111) [110] cold-rolled crystal produces a limited number of weak and strong components with the larger than average primary grains from these components related to the cold-rolled crystal by 25° <110> relationships. In arriving at this conclusion of limited orientations the (111) [110] orientation has to be ruled out as a source of large primaries for two reasons. First, growth in this orientation was not observed, despite an expected high grain boundary mobility (due to its 25" <110> relationship with every component of the texture). Secondly, primary recrystallization usually produces grains in new orientations, particularly in a single orientation matrix; but (111) [110] is not new. Other orientations besides those of the <110> type may be considered unlikely, of course, because the <110> relationship holds quite well for primary recrystallization2 and should produce the large primaries. There are exceptions to this rule, but probably not enough to provide large

Jan 1, 1958

By Richard H. Jahns

GRANITIC pegmatite deposits are the chief source of commercial feldspar, sheet mica, beryllium, tantalum-columbium, and lithium minerals, and certain types of kaolin. They also have yielded significant quantities of cassiterite, gems, scrap mica, molybdenite, tungsten minerals, uranium-thorium and rare-earth minerals, and zircon, either directly or as the sources of placer deposits. The output from pegmatite mines in the United States is small as compared to other mineral products in terms of bulk or value, and much of it comprises minor metals and nonmetals. Nevertheless, pegmatite minerals play a vital part in domestic industrial economy, particularly in the ceramic and electrical industries. Numerous special purpose uses also are important, even though they require small quantities of raw materials. Never was United States dependence upon pegmatite mining more clearly emphasized than during World War 11, when greatly expanded demands and uncertainties of foreign sources of supply caused much concern. Such commodities as beryl, tantalite, and sheet muscovite remained high on the critical list for months at a time, and for some minerals there was a real struggle to achieve and maintain a favorable ratio of supply to demand. Satisfactory stock piles of certain sizes and qualities of sheet mica, for example, were not built up until late in 1944, when wartime requirements already had begun to level off or even to decrease. Production of all the strategic pegmatite minerals from domestic deposits during World War I1 constituted only 10 pct or less of the total domestic consumption of these minerals, but the importance of this contribution should not be minimized. Domestic production often represented the difference between increase and further reduction of existing stocks of commodities already in seriously short supply, and in the early stages of the war it was the only assured source if imports were cut off. During the recent war period, the U. S. Geological Survey carried on a program of pegmatite studies in the New England and Southeastern States, in the Black Hills area of South Dakota, in the Rocky Mountain region of Wyoming, Colorado, and New Mexico, and in various parts of Washington, Idaho, Utah, Nevada, Arizona, and California as shown in Fig. 1. Several papers and reports already have appeared as an outgrowth of this work,&apos;-= and others are in preparation. This paper outlines some results of data obtained by the writer during the period 1942 to 1946, when he was engaged in studies of pegmatites in the Southeastern, Southwestern, and Rocky Mountain States. Beryllium Minerals Beryl is the present commercial source of beryllium metal and beryllium compounds, which are used in ceramics, in the preparation of X-ray tubes and fluorescent lamps and screens, in special processes of paint and textile manufacture, and in the optical systems of some electrical instruments. The metal also is used in nuclear physics, chiefly as a source of neutrons. Beryllium is alloyed with aluminum for certain light-metal uses and is a constituent of some nickel and iron alloys. Currently the chief demand, however, is for copper-base alloys, which are exceptionally resistant to fatigue and wear, are responsive to hardening treatments after

Jan 1, 1952

By John V. Beall

When the mineral seekers came, they brought romance, excitement and, too often, transitory riches. It has been so for uncounted centuries. While the rich ore lasted, living was high and money flowed-mostly out of town. The whole creation was like a circus. The headframe went up like the center pole of the big top. The reduction works was an ingenious affair; an opportunity for self-expression by the mining engineer on the job. When the high grade gave out or the bottom dropped out of the market, the whole show folded. Machinery was scavenged for the next location. About all that was left were the raw footings, like giantsteps on the hillside; and the headframe above the silent diggings. Mostly, the people went away too. Arizona Territory was like that at the turn of the century. It can still happen. But, in copper, the age-old pattern has been disrupted. From Mineral Park in the northwest to Chino in the east and Cananea in the South, a growing number of companies have emerged-large, stable, productive. Southwest copper is truly a mighty industry, accounting for one fifth of world new copper production. In this period of scientific development, changes are fast, often dramatic. But even mining engineers, or possibly more so because they have an intimate knowledge of the industry, fail to appreciate the evolutionary changes that have shaped Southwest copper into what it is today.

Jan 10, 1965

By Burnham E. Field

The chemical industry is constantly looking for new materials which either are more resistant to corrosion than those now available or have improved physical properties to meet the requirements of higher temperatures and greater pressures. Attack by acids is one of the more important forms of corrosion and in the last few years the development of acid-resistant alloys has been quite rapid. Perhaps the most notable example is that of nitric acid, the problem of which has largely been solved by the chromium-iron and chromium-iron-nickel alloys. Sulfuric acid may be handled in lead, iron, or the iron-silicon alloys, depending on conditions. As to hydrochloric acid, no metal or alloy can be called entirely satisfactory for handling this acid under plant conditions.&apos; The results of our investigations on the resistance of the nickel-molybdenum alloys to hydrochloric acid have been confirmed by those of Guertler, Rohn, Schulz, Jenge, and others12 but thus far only one such alloy has approached commercial production in Germany; this contains approximately 15 per cent. chromium and 7 per cent. molybdenum with the remainder chiefly nickel. Dr. S. W. Parr, as far back as 1914, developed a complex alloy known as "illium," with a nickel base and containing some molybdenum. 3 Dr. Parr was primarily interested in an alloy for lining bomb calorimeters, and while illium does show good resistance to acid it is too expensive for general use. Two United States

Jan 1, 1929

By Burnham E. Field

The chemical industry is constantly looking for new materials which either are more resistant to corrosion than those now available or have improved physical properties to meet the requirements of higher temperatures and greater pressures. Attack by acids is one of the more important forms of corrosion and in the last few years the development of acid-resistant alloys has been quite rapid. Perhaps the most notable example is that of nitric acid, the problem of which has largely been solved by the chromium-iron and chromium-iron-nickel alloys. Sulfuric acid may be handled in lead, iron, or the iron-silicon alloys, depending on conditions. As to hydrochloric acid, no metal or alloy can be called entirely satisfactory for handling this acid under plant conditions.&apos; The results of our investigations on the resistance of the nickel-molybdenum alloys to hydrochloric acid have been confirmed by those of Guertler, Rohn, Schulz, Jenge, and others12 but thus far only one such alloy has approached commercial production in Germany; this contains approximately 15 per cent. chromium and 7 per cent. molybdenum with the remainder chiefly nickel. Dr. S. W. Parr, as far back as 1914, developed a complex alloy known as "illium," with a nickel base and containing some molybdenum. 3 Dr. Parr was primarily interested in an alloy for lining bomb calorimeters, and while illium does show good resistance to acid it is too expensive for general use. Two United States

Jan 1, 1929

By Donald L. Katz

Charts for predicting the pressure to which natural gases may be expanded without hydrate formation have been prepared for gases of even gravity. Pressure-temperature curves for hydrate formation were established for gases having gravities from 0.6 to 1.0. These curves and the thermal behavior of the gases during free and adiabatic expansion were used to prepare the charts for estimating the permissible expansion of natural gases without hydrate formation. The problem was solved by L. F, Albright, W. T. Boyd, J. J. McKetta, G. Martin, P. Poettman. and A. P. Snyder.-, who are first-year graduate students in the department of Chemical and Metallurgical Engineering at the University of Michigan. This paper is essentially a summary of their results. Prediction of Conditions for Hydrate Formation in Natural Gases Each natural gas under a given pressure will form solid hydrates at a corresponding temperature provided sufficient water is present.1-5 The temperature of natural gases below about 5000 lb. per sq. in. decreases when the gases are expanded freely.6,7 This decrease in temperature may cause the expanding gas to enter the region of temperature and pressure at which hydrates will form&apos; The final pressure to which a natural gas may &apos;be expanded without hydrate formation depends upon the initial temperature and pressure and the gas composition. This paper presents charts that give the final pressures to which gases of gravity 0.6 to 1.0 at given initial temperatures and pressures may be expanded without formation of hydrate. Hydrate-forming Temperatures and Pressures as a Function OF Gas -Gravity Experimental data of pressure versus temperature at which solid hydrate will form, provided sufficient water is present, are available for a series of gases.2,3 A method of predicting the pressure-temperature curve for a given gas composition has been reported.&apos; The solution to this problem requires that these curves relating pressure to temperature be established for gases of given gravities.

Jan 1, 1945

By SME

"Comparison of Secondary Fe-Mn Oxides in Fracture Coating and Heavy-Mineral Concentrates as Sampling Media, Silver City Mining Region, New Mexico," a technical paper, appeared in the Aug. 1983 issue of the magazine. In Table 1, page 1182, the correct sequence of the first five metals in column 1 (Elements) should read: Zn, Pb, Cu, Fe, and Mn under "Central District" and Zn, Fe, Pb, Cu, and Mn under "Pinos Altos District." The published table shows the sequences transposed under the opposite districts. All other columns and sequences read correctly.

Jan 1, 1984

By William P. Shinn

MR. GAYLEY&apos;S admirable paper on the " Development of American Blast-Furnaces" has set forth very fully the history of the development of the Edgar Thomson furnaces since the construction of Furnaces A and B ; but it throws no light on the genesis of these furnaces. That earlier history it is the purpose of the present paper to record. Mr. Gayley truly says: "A new era in the manufacture of pigiron began in 1880 with the putting in blast of the Edgar Thomson furnaces." That era had its beginning with the construction of

Jan 1, 1891

By G. R. St. Pierre, S. W. Gilby

The equilibrium vapors established over Fe-Cr-Ni alloys containing up to 50 pct Cr at 1600°C were determined by collecting the effusate from thoria Knud-sen cells. From these data, the activities of iron and nickel in the ternary alloys have been calculated. In a separate set of measurements, a mass spectrometer was used to determine the activities of the three components in a series of Fe-Cr-Ni alloys. In binary Ni-Cr melts, the activity coefficient of chromium referred to pure solid chromium as standard state is less than one at low chromium contents but is greater than one for melts containing more than 30 at. pct Cr. For Ni-Cr melts containing less than 10 at. pct Cr, In ?Cr = 0.15-0.92 N2. Ternary activity diagrams for Fe-Cr-Ni alloys are presented. In iron-rich alloys, the interactions between the three components are negligible; however, in nickel-rich alloys, the three principal interactions have significant positive values. THE activities of components in binary Fe-Ni alloys have been measured both in the solid solution1-3 and liquid solution4-6 temperature ranges. The determination for Fe-Ni melts have been made by three different methods: transpiration,4 Knudsen-cell effusion with analysis of an accumulated condensate,&apos; and Knudsen-cell effusion with direct measurements of relative component intensities by mass spectrometric methods.6 The results obtained by the three different methods in three different laboratories are in excellent agreement and considerable confidence is placed in the activity coefficients for Fe-Ni melts. At 1600°C, the activity coefficients in dilute solution are ?°Ni = 0.66 and ?oFe = 0.40 for the pure liquid components as standard states. Measurements made on solid solution Fe-Cr alloys7-10 indicate that the component activities are slightly greater than ideal. The measured activities in iron-rich Fe-Cr liquid alloy11-16 indicate almost ideal behavior for this system. The recommended activity coefficient of chromium in dilute solution in liquid iron at 1600o C, ?oCr, is 1.18 when referred to pure solid chromium as standard state and 1.04 when referred to pure undercooled liquid chromium as standard state." The conversion factor of 1.14 is based on a melting point of 1857°C and an enthalpy of melting of 4047 cal per g at. for chromium.21,37 The activity coefficient of iron in dilute solution in liquid chromium has not been measured. Activity measurements on solid Ni-Cr alloys have been made by several investigators.17-20 During the review of this manuscript, Fruehan12 published the results of a study on liquid Ni-Cr alloys at 1600°C. He used galvanic cells22 with ZrO2(CaO) as the electrolyte and Cr/Cr2O3 for the reference electrode. His results indicate that ?oCr in nickel at 1600°C is about 1.01 when referred to pure solid chromium and about 0.89 when referred to pure undercooled liquid chromium as standard state. The activity coefficient of nickel in liquid chromium is unknown. The compositions of vapors freely evaporating from some molten Fe-Cr-Ni alloys have been measured by Lyubimov, Granovskaya, and Berenstein.23 Their results, combined with known vapor pressures, indicate strong positive deviation for chromium in iron-rich alloys and strong negative deviation for chromium in nickel-rich alloys. EXPERIMENTAL PROCEDURES This research was undertaken to determine the activities of components in ternary Fe-Cr-Ni melts containing up to 50 at. pct Cr. At the initiation of the research, we decided to use a Knudsen-cell method wherein a portion of the effusing vapor is condensed on a cold plate.&apos; The composition of the equilibrium vapor for each alloy composition is determined in this method by holding the system under constant conditions for a period of time sufficient to collect enough condensate on the cold plate for chemical analysis. The activities of components in ternary alloys can be calculated from such vapor composition determinations by Eq. [1].24

Jan 1, 1970

By G. W. Binkley, G. K. Dumbauld, F. A. Brooks, B. E. Morgan

In recent years, oil well cementing compositions have been developed with low densities, controlled set strengths, and satisfactory thickening times. With the introduction of the permanent-type well completion method for cementing wells, another property—that of rate of filtration or water loss to permeable formations— has become important. Laboratory data show that cement slurries prepared with oil, water, bentonite, and calcium lignosulfonate possess satisfactory thickening times, strengths, and filtration properties for primary cementing of casing and for squeeze cementing with the permanent-type well completion technique. Cementing compositions have been prepared with oil-in-water emulsions varying in composition from 60 cc water and 20 cc oil per 100 gm cement to 90 cc water and 45 cc oil per 100 gm cement. These compositions have contained from 0.4 to 5.0 per cent calcium lignosulfonate by weight of dry cement. Slurries prepared from these compositions weigh 11.4 to 13.1 lb/ga1 and have filtration rates of from 10 cc to approximately 100 cc in 30-min API tests at room temperature. The unfiltered emulsion cements develop one-day tensile strengths of 60 to 220 psi; and the filtered mass sets to tensile strengths of 60 to 150 psi in 12 hours and develops strengths of 320 to 515 psi in seven days when cured at 125° F. Field experience gained from 13 field mixing jobs demonstrates the utility of the emulsion cement for permanent-type squeeze cementing operations. INTRODUCTION In recent years, research in oil well cementing composition has been directed toward the development of cements having low densities, controlled set strengths, satisfactory thickening times, and low rates of water loss by filtration. Two well cementing compositions that have been developed with these properties are the modified cements containing, respectively, 12 and 25 per cent bentonite clay and various concentrations of calcium lignosulfonate1,2 In a search for other ways to incorporate these characteristics in a cementing composition, consideration was given to the rheological properties of oil-emulsion drilling fluids. Many of the desirable properties observed in oil-emulsion drilling fluids are equally advantageous in a cementing composition. For example, low water loss by filtration and low density, which are inherent characteristics of these oil-in-water emulsions, are desirable for many oil well cementing operations. Furthermore, oil-emulsion slurries have lubricating properties similar to those of oil-emulsion muds, a factor which should provide ease of rotation of casing during primary cementing operations. The properties of lubrication and low filtration may be of special value in both primary and squeeze cementing operations encountered in slim-hole drilling. Studies in the preparation of oil emulsion systems have pointed out the need for violent agitation in order to disperse the oil into the water phase. It was thought, therefore,

Jan 1, 1957

By William D. Klopp, Joseph R. Stephens

Chromium alloys were coated with silicon, alumi-nuw, and boron by pack cementation. None of these simple coatings provided adequate nitridation/oxida-tion protection for a Cr -0.17pct Y alloy substrate as shown by a substantial Increase in the ductile -brittle transition temperature after air exposure for 100 hr at 2100°F. Iron-modified silicide coatings afforded good protection, holding the transition temperature of air-exposed specimens to 350° F compared to 200° F for uncoated unexposed specimens and 800°F for un-coated exposed specimens. Additional attractive cant-binations of modi-tying elements included Fe-mo, Fe-Mo-W, Fe-,Mo-W-Ti, and V-Mo-W-Ti. THE desirability of increased operating tempera-tures as a mcans of improving the performance of ad-vanced air breathing engines has resulted in emphasis on the development of materials with high operating temperature capabilities. Chromium, because of its relatively low density (7.19 g per cu cm), high melt-ing point (3410°F), and adequate strength upon alloy-ing, is a candidate material for turbine buckets and stator vanes of advanced air breathing engines. How-even, chromium is not without severe limitations, the major one being susceptibility to nitrogen embrittle-ment upon exposure to air at high temperatures.1,2 For example, a 25-hr air exposure of a Cr-5 pct W* * All compositions in wt pct. alloy at 2100°F produces a 600°F increase in the duc-tile-brittle transition temperature.&apos; Although dilute alloying with such elements as yttrium, lanthanum, arid thorium3,4 or strong nitride formers5 has been shown capable of reducing nitrogen embrittlement, it is apparent that some additional form of surface protection, such as coatings or claddings, will be required for long time service in air breathing engines. Studies of aluiminide6 and silicide7 coatings and of nickel-base claddingsl on chromium alloys to date have suggested that these protection systems are inadequate. Of the aluminidc systems Studied,6 a simple aluminum and an Fe-Al coating on a Cr-5 pct W-0.1 pct Y alloy showed the lowest air exposure weight gains. However, the air exposures raised the ductile-brittle transition temperature of the coated specimens to above 1600°F from an initial level in unexposed specimens of about 500°F. A second in-vestigation for protection of Cr-5 pct W-0.1 pct Y employed gas pressure bonded alloy foils as protective claddings.1 An aluminized Ni-20 pct Cr-20 pct W alloy plus an unalloyed tungsten barrier layer gave the best performance with air exposure lives based on appearance and weight gains of over 600 hr at 2100°F. However, the bend ductile-brittle transition tempera-ture was increased to at least 1000°F after 100 hr at

Jan 1, 1970

By C. H. Curtis

HE valuable mineral content of the current feed -*- to the Miami concentrator is as follows: copper, 0.7 pct total; molybdenum, 0.01. Flotation of this ore yields a sulphide concentrate containing: chalco- cite, 44 pct; molybdenite, 0.5; pyrite, 50.0; insol, 5.5. A combination of potassium ethyl xanthate and pentasol amyl xanthate as collectors, and pine oil as frother, are used in this flotation. Rejection of pyrite is encouraged by holding the amount of collectors used to the minimum consistent with copper recovery and by operating at high alkalinity (equivalent to 0.35-0.40 lb CaO per ton solution of pH 11.0). The molybdenum recovery in the sulphide concentrates under the above flotation conditions is approximately 50 pct of that originally present in the ore. Taking into account the acid soluble molybdenum, indicated molybdenite recovery is 75 to 80 pct. The attempt to separate the molybdenite into an acceptable molybdenum product begins with the bulk sulphide flotation concentrate just described. This concentrate is composed of chalcocite, whose floatability has been promoted to the fullest extent possible for the sake of its recovery from the ore, together with the pyrite which has been activated along with the copper mineral. The problem is to deaden the copper and iron minerals, and to float the molybdenite. Obviously in the accomplishment of this end, conditioning and preparation of the pulp, prior to flotation, plays an all important role. The first step is thickening to 50 to 60 pct solids, with milk of lime added to the thickener feed to maintain an alkalinity of the pulp equivalent to a pH of 8.5 to 8.8 during its residence in the thickener. The purpose of the thickening is primarily to reduce the volume of pulp for subsequent treatment. However, the relatively prolonged retention of the pulp in the thickener at the desired alkalinity is known to have a favorable depressing effect upon pyrite. There is a limit for this alkalinity above which a depressing effect upon molybdenite occurs. The thickened pulp (alkalinity: 0.015 lb CaO per ton, pH 8.8), discharges into an agitator, retention time approximately 2 hr, to which additional lime is added to raise the alkalinity to 0.35 to 0.40 lb CaO per ton solution, pH 11.6. This additional lime is required for pyrite depression and can be tolerated without loss of molybdenite because of the limited time of contact in the conditioner tank. The pulp leaving the lime conditioner passes through two successive steaming tanks, which are mechanically agitated, and into which live steam is admitted directly into the pulp near the bottom of the tanks. The temperature of the pulp is maintained as near boiling as possible. The steaming time is approximately 4 hr. The pulp leaving the last steamer has an alkalinity of about 0.04 lb Cao per ton solution, pH 8.7. It is believed that oxidation of the copper and iron sulphides occurs during steaming, the resulting sulphates reacting the calcium hydroxide to calcium sulphate and thus reducing the alkalinity. Since the steamer-feed solution is already saturated with calcium sulphate, the calcium sulphate produced during steaming is precipitated. It is believed that this calcium sulphate is precipitated preferentially on copper and iron mineral surfaces thus decreasing their floatability. Aside from the "lime chemistry" during steaming, pine oil is displaced from the pulp and xanthate decomposed, which has a major effect upon the deadening of the copper and iron sulphides. Following steaming, the hot pulp is admitted to another conditioning tank wherein it is aerated, primarily for cooling, but incidentally for additional oxidation of the copper and iron sulphides. The resulting "deadened" pulp is then diluted to 20 pct solids, a specific collector for molybdenite, ordinary stove oil, is added and the separation of the molybdenite by flotation is undertaken at a pH of 8.5 to 8.8 in standard Miami air-flotation ma-chines. B-22 frother is used when necessary. A re-grind of the thickened rougher concentrates is made prior to the first cleaning operation chiefly for rejection of insoluble in subsequent flotation. The cleaner concentrate is then stepped up to 90 pct MoS, in an 8-cell Denver flotation machine No. 18. Sodium silicate is added to the cleaner circuit. Its effect is to flocculate molybdenite and stabilize the froth. In summary, it may be stated: 1. Separation of molybdenite into an acceptable product from sulphide copper concentrates by flotation involves preliminary preparation and conditioning of the pulp, which is of major importance. 2. This preparation and conditioning consists of several successive steps: (A) Thickening to 50 to 60 pct solids at controlled alkalinity to reduce volume of pulp and to contribute to depression of pyrite. (B) Agitation at high-pulp density for limited time with additional lime to provide for depression of pyrite. (C) Steaming at high-pulp density for decomposition of xanthate and xanthate surface films, evolution of pine oil, and oxidation of sulphide minerals other than molybdenite. The latter involves sulphating of lime with probable precipitation of calcium sulphate preferentially on copper and iron minerals. (D) Aeration at high-pulp density for cooling, and for further oxidation of copper and iron sulphide minerals. (E) Dilution of pulp to 20 pct solids and addition of specific collector for molybdenite, common stove oil. It is hardly necessary to point out that this rather drastic procedure for depression of previously activated copper and iron sulphide minerals, without at the same time depressing molybdenite, is possible due to the inherently high floatability and refractory nature of molybdenite. However, molybdenite is susceptible to depression by excessive lime which must therefore be limited to the amount consistent with satisfactory molybdenite recovery. The steaming procedure is being carried on at Miami Copper Co. under license agreement with Janney, Nokes, and Johnson, holders of letters patent on the process.

Jan 1, 1951

By C. H. Curtis

HE valuable mineral content of the current feed -*- to the Miami concentrator is as follows: copper, 0.7 pct total; molybdenum, 0.01. Flotation of this ore yields a sulphide concentrate containing: chalco- cite, 44 pct; molybdenite, 0.5; pyrite, 50.0; insol, 5.5. A combination of potassium ethyl xanthate and pentasol amyl xanthate as collectors, and pine oil as frother, are used in this flotation. Rejection of pyrite is encouraged by holding the amount of collectors used to the minimum consistent with copper recovery and by operating at high alkalinity (equivalent to 0.35-0.40 lb CaO per ton solution of pH 11.0). The molybdenum recovery in the sulphide concentrates under the above flotation conditions is approximately 50 pct of that originally present in the ore. Taking into account the acid soluble molybdenum, indicated molybdenite recovery is 75 to 80 pct. The attempt to separate the molybdenite into an acceptable molybdenum product begins with the bulk sulphide flotation concentrate just described. This concentrate is composed of chalcocite, whose floatability has been promoted to the fullest extent possible for the sake of its recovery from the ore, together with the pyrite which has been activated along with the copper mineral. The problem is to deaden the copper and iron minerals, and to float the molybdenite. Obviously in the accomplishment of this end, conditioning and preparation of the pulp, prior to flotation, plays an all important role. The first step is thickening to 50 to 60 pct solids, with milk of lime added to the thickener feed to maintain an alkalinity of the pulp equivalent to a pH of 8.5 to 8.8 during its residence in the thickener. The purpose of the thickening is primarily to reduce the volume of pulp for subsequent treatment. However, the relatively prolonged retention of the pulp in the thickener at the desired alkalinity is known to have a favorable depressing effect upon pyrite. There is a limit for this alkalinity above which a depressing effect upon molybdenite occurs. The thickened pulp (alkalinity: 0.015 lb CaO per ton, pH 8.8), discharges into an agitator, retention time approximately 2 hr, to which additional lime is added to raise the alkalinity to 0.35 to 0.40 lb CaO per ton solution, pH 11.6. This additional lime is required for pyrite depression and can be tolerated without loss of molybdenite because of the limited time of contact in the conditioner tank. The pulp leaving the lime conditioner passes through two successive steaming tanks, which are mechanically agitated, and into which live steam is admitted directly into the pulp near the bottom of the tanks. The temperature of the pulp is maintained as near boiling as possible. The steaming time is approximately 4 hr. The pulp leaving the last steamer has an alkalinity of about 0.04 lb Cao per ton solution, pH 8.7. It is believed that oxidation of the copper and iron sulphides occurs during steaming, the resulting sulphates reacting the calcium hydroxide to calcium sulphate and thus reducing the alkalinity. Since the steamer-feed solution is already saturated with calcium sulphate, the calcium sulphate produced during steaming is precipitated. It is believed that this calcium sulphate is precipitated preferentially on copper and iron mineral surfaces thus decreasing their floatability. Aside from the "lime chemistry" during steaming, pine oil is displaced from the pulp and xanthate decomposed, which has a major effect upon the deadening of the copper and iron sulphides. Following steaming, the hot pulp is admitted to another conditioning tank wherein it is aerated, primarily for cooling, but incidentally for additional oxidation of the copper and iron sulphides. The resulting "deadened" pulp is then diluted to 20 pct solids, a specific collector for molybdenite, ordinary stove oil, is added and the separation of the molybdenite by flotation is undertaken at a pH of 8.5 to 8.8 in standard Miami air-flotation ma-chines. B-22 frother is used when necessary. A re-grind of the thickened rougher concentrates is made prior to the first cleaning operation chiefly for rejection of insoluble in subsequent flotation. The cleaner concentrate is then stepped up to 90 pct MoS, in an 8-cell Denver flotation machine No. 18. Sodium silicate is added to the cleaner circuit. Its effect is to flocculate molybdenite and stabilize the froth. In summary, it may be stated: 1. Separation of molybdenite into an acceptable product from sulphide copper concentrates by flotation involves preliminary preparation and conditioning of the pulp, which is of major importance. 2. This preparation and conditioning consists of several successive steps: (A) Thickening to 50 to 60 pct solids at controlled alkalinity to reduce volume of pulp and to contribute to depression of pyrite. (B) Agitation at high-pulp density for limited time with additional lime to provide for depression of pyrite. (C) Steaming at high-pulp density for decomposition of xanthate and xanthate surface films, evolution of pine oil, and oxidation of sulphide minerals other than molybdenite. The latter involves sulphating of lime with probable precipitation of calcium sulphate preferentially on copper and iron minerals. (D) Aeration at high-pulp density for cooling, and for further oxidation of copper and iron sulphide minerals. (E) Dilution of pulp to 20 pct solids and addition of specific collector for molybdenite, common stove oil. It is hardly necessary to point out that this rather drastic procedure for depression of previously activated copper and iron sulphide minerals, without at the same time depressing molybdenite, is possible due to the inherently high floatability and refractory nature of molybdenite. However, molybdenite is susceptible to depression by excessive lime which must therefore be limited to the amount consistent with satisfactory molybdenite recovery. The steaming procedure is being carried on at Miami Copper Co. under license agreement with Janney, Nokes, and Johnson, holders of letters patent on the process.

Jan 1, 1951

By R. J. Marcotte, C. T. Eddy, R. J. Smith

The objectives of the investigation herein reported were to determine: (I) the S-curves for certain selected cast steels, (2) whether or not the published S-curves for wrought steels are satisfactory for use on cast steels of similar composition, and (3) to prepare hardenability curves of the selected cast steels. In order to make the final comparisons between cast and wrought steel more completely tangible, it was deemed advisable not only to determine S-curves for the steels submitted in the cast condition but also to roll some of the cast-steel test bars and determine comparison S-curves on such wrought material. This procedure eliminates the composition variable and makes it possible to reveal the differences resulting from plastic deformation of the cast structure in addition to providing the comparison with published data on wrought steels. Cast Steels The cast steels selected for the preparation of S-curves, or time-temperature transformation curves, were similar to S.A.E. series 1030, 2330, 4130 and 4330. Of these the 1030 was supplied by The Crucible Steel Casting Co., Cleveland, Ohio, and the other three by The Sawbrook Steel Castings Co., Lockland, Ohio. The steels were furnished in the as-cast condition. The manufacturers supplied the chemical analyses and the properties that could be obtained in the heat-treated condition—all of which is summarized in Table I. The metallographic and dilatometric procedures and equipment were in general standard. The specific technique employed was described in a report of the Steel

Jan 1, 1945

By R. H. Jacoby, V. J. Berry

Future depletion performance and ultimate oil recovery from reservoirs producing under volumetric control are often predicted with the aid of a material balance equation. When the reservoir fluid is very volatile, however, certain assumptions implicit in the use of the conventional methods are no longer valid. This is became laboratory differential vaporization test procedures do not adequately represent the reservoir depletion process and the performance of surface separation facilities. In such cases recovery of stock tank oil per unit of pressure decline can be predicted only from a detailed knowledge of the separator conditions and the over-all composition of the fluid entering the wellbore at each stage of depletion. Surface recovery is not simply related to the total quantity of liquid flowing into the well under reservoir conditions. In order to improve predictions for reservoirs which produce volatile oils, a step wise method of calculation has been developed. This method uses relative permeability data and multicomponent flash calculations to predict oil and gas production as a function of reservoir pressure. Calculations are presented for a reservoir containing a volatile crude oil, and predicted tank oil recovery by primary depletion is more than twice that predicted by conventional methods which are known to be adequate for ordinary black crude oils. Calculated maximum produced gas-oil ratio is less than one-fourth of the conventional prediction. Wellstream compositions have also been used to determine variation in stock tank oil composition and liquid content of the separator gas. This information is of particular importance for crude stabilization calculations and for design of gasoline plant facilities to recover LPG and natural gasoline. INTRODUCTION The estimation of oil reserves and the prediction of future recovery performance of petroleum reservoirs is a frequent task of the petroleum engineer. If the reservoir produces under volumetric control, performance calculations for primary depletion are made by combining oil and gas material balances with the gas-oil flow characteristics of the reservoir rock. For black oil reservoirs, the Schilthuis1 type material balance is commonly employed. For gas or gas-condensate reservoirs, where only one phase is flowing under bottom-hole conditions, a more simplified material balance is used. In the period in which these material balance methods were conceived and put into practice, it was common to classify reservoirs according to the type of fluid produced as (1) black oil reservoirs, or (2) gas or gas-condensate reservoirs. Recently, however, deeper drilling and more extensive studies of reservoir fluid properties have led to the recognition of reservoir fluids with phase characteristics between those of ordinary black oils, and gases or gas-condensate fluids. These intermediate fluids contain relatively large amounts of the hydrocarbons ethane through decane and are found in deep, high temperature (250°F) reservoirs. Such fluids are often referred to as high shrinkage crudes or "volatile oils." They are usually characterized by tank oil gravities above 45° API. high solution gas/oil ratios,

Jan 1, 1958

By C. E. Berry

Natural stone or manufactured porcelain pebbles are used as the grinding elements in pebble mills and the mills are lined with stone or porcelain blocks. Steel balls usually form the grinding medium in ball mills, and the mills may be lined with steel. Pebble mills are used to avoid contamination by metal of the material being ground, to avoid rapid wear due to corrosion, and for other specialized reasons. Belgian silex (silica) blocks formerly were used widely for lining pebble mills, because of their good resistance to wear, light color, and low cost, but the importation of these blocks was suspended early in the war. The stocks of Belgian silex diminished so rapidly that it was found desirable to compare the properties of a number of domestic substitutes for use in critical operations. Accordingly, a study was made to determine the best substitutes for fine grinding of white pigment and for certain heavy-chemical process work such as the disintegration of phosphate rock in weak phosphoric acid solution. A comprehensive survey of substitute lining materials was not contemplated. It was stipulated at the beginning of the investigation that only materials on the market, available in large quantities, would be tested and that these should be reasonable substitutes from a a ance viewpoint as determined from known physical characteristics. Marble and limestone, for example, could be eliminated immediately. Quartzite, granite and porcelain were selected as likely substitutes for Belgian silex and were subjected to quality tests. Materials Tested 1. Belgian Si1ex.—Sample blocks of a standard grade were taken from crates in which they had been imported. The stone was light gray in color and contained inclusions of small clusters of quartz crystals as well as light colored portions that might be calcite. This was a siliceous rock which appeared to be of igneous origin. 2. Quartzite.—Samples of quartzite were obtained from a quarry in Minnesota. The blocks exhibited a crystalline fracture. The stone was pink in color and composed of fine quartz crystals bound together with a siliceous cement. 3. Granite A was a fine-grained granite quarried in South Carolina. 4. Granite B was coarse-grained granite quarried in South Carolina. 5. Granite C was a coarse-grained granite quarried in North Carolina. 6. Porcelain A.—Sample blocks of the pebble-mill lining material were obtained direct from the manufacturer. It was white in color and of lower specific gravity than the natural materials. It did not have a crystalline structure. 7. Porcelain B.—Sample pebble-mill lining blocks of the porcelain were received direct from the manufacturer. It was white

Jan 1, 1948

By C. E. Berry

Natural stone or manufactured porcelain pebbles are used as the grinding elements in pebble mills and the mills are lined with stone or porcelain blocks. Steel balls usually form the grinding medium in ball mills, and the mills may be lined with steel. Pebble mills are used to avoid contamination by metal of the material being ground, to avoid rapid wear due to corrosion, and for other specialized reasons. Belgian silex (silica) blocks formerly were used widely for lining pebble mills, because of their good resistance to wear, light color, and low cost, but the importation of these blocks was suspended early in the war. The stocks of Belgian silex diminished so rapidly that it was found desirable to compare the properties of a number of domestic substitutes for use in critical operations. Accordingly, a study was made to determine the best substitutes for fine grinding of white pigment and for certain heavy-chemical process work such as the disintegration of phosphate rock in weak phosphoric acid solution. A comprehensive survey of substitute lining materials was not contemplated. It was stipulated at the beginning of the investigation that only materials on the market, available in large quantities, would be tested and that these should be reasonable substitutes from a a ance viewpoint as determined from known physical characteristics. Marble and limestone, for example, could be eliminated immediately. Quartzite, granite and porcelain were selected as likely substitutes for Belgian silex and were subjected to quality tests. Materials Tested 1. Belgian Si1ex.—Sample blocks of a standard grade were taken from crates in which they had been imported. The stone was light gray in color and contained inclusions of small clusters of quartz crystals as well as light colored portions that might be calcite. This was a siliceous rock which appeared to be of igneous origin. 2. Quartzite.—Samples of quartzite were obtained from a quarry in Minnesota. The blocks exhibited a crystalline fracture. The stone was pink in color and composed of fine quartz crystals bound together with a siliceous cement. 3. Granite A was a fine-grained granite quarried in South Carolina. 4. Granite B was coarse-grained granite quarried in South Carolina. 5. Granite C was a coarse-grained granite quarried in North Carolina. 6. Porcelain A.—Sample blocks of the pebble-mill lining material were obtained direct from the manufacturer. It was white in color and of lower specific gravity than the natural materials. It did not have a crystalline structure. 7. Porcelain B.—Sample pebble-mill lining blocks of the porcelain were received direct from the manufacturer. It was white

Jan 1, 1948

By William R. Webster

In view of the great interest now taken in the tests of castiron and details of foundry practice, with the number of investigators at work, and recent improvements in the methods of research, it would seem that the time is ripe to attempt the solution of some of the many problems with which iron founders have to contend. Recent papers and discussions on these subjects* have opened up s large field for investigation, and have emphasized the importance of many considerations generally overlooked. With the view of promoting a comprehensive and systematic discussion, I have attempted to tabulate, in conveilient form, some of the most important points for investigation, on the general plan suggested, with such good results, by our former President, H. M. Howe, for the discussion on the Physics of Steel, at the Virginia Beach meeting, last year. This table can, no doubt, be modified or enlarged to advantage, and put in shape to serve as a guide or reminder to all who are interested in this line of work. Suggested Lines for Discussion and Investigation. I.—Correspondence between chemical composition and melting point, fluidity, shrinkage, fracture, chill, micro-structure, and other physical properties. II.—Influence of: I. Cupola mixture, use of steel and other scrap, oxidized or clean material, 2. Manner of melting, flux, etc., 3. Casting temperature, A. Fracture. 4. Manner of handling melted metal and B. Micro-structure. method of casting, C. Physical properties. 5. Size and form of casting, D. Shrinkage. 6. Kind of mould, green sand (under dif- on 1 E. Chill. ferent conditions of ramming, amount F. Residual stress. of moisture, and skin-dried), dry sand, G. Condition and quan loam, and chills, tity of carbon and 7. Rate and mode of cooling castings, other elements. 8. Manner and temperature of heating for annealing, 9. Additions of nickel or aluminum,

Jan 1, 1896

HeRbeRT Haas,—(communication to the Secretary*).—Fig. I plainly shows that the comparison of the steam-turbine and Diesel-engine plants was made on a basis of 6,000 kw. continuous operating load. The tabulation of costs for an 8,000-kw. load is merely done to show the relation of increased output on the unit power costs. Both plants would sacrifice their reserve capacity, which is to insure continuous operation, if operated to generate 8,000 kw. continuously; unless Mr. Hawkins advocates the operation of one of the turbines at 33.33 per cent. overload, retaining the other as a standby, which, besides overtaxing the turbine, results in a great loss of efficiency. It would be well for Mr. Hawkins to qualify certain of his statements. Thus, under the caption "Diesel Engines, Selection of Units," he says that &apos;(two of the largest Diesel-engine builders take the position that, in the present state of the art, they would not attempt to put out units over 1,000 kw.;" he should qualify it by saying that "two of the largest American Diesel-engine builders take the position that, in the present state of the art in the United States, they would not attempt to put out units over 1,000 kw." The reason that American manufacturers restrict themselves at present to units of that size is to be found not so much in a lack of experience in building large units as in a lack of a sufficient demand for them in the United States to justify the heavy capital outlay connected with the development of such engines. There are relatively few localities in the United States where fuel prices are as high as they are in the South-, west, and regions of high fuel prices are sparsely settled and have a very limited demand for power. Where low fuel prices obtain, steam turbines are active competitors of Diesel engines for large power plants, particularly when the station load factor is low. As most of the American manufacturers of Diesel engines work under license agreements with European manufacturers, which limit their market to the United States and its possessions and Canada, a further limitation is imposed upon them, leaving to European firms practically the entire world as a market. The greater number of power plants range in size from 300 to 1,000 hp.; the average size of the central station, on a basis of all central stations in the United States, not greatly exceeding 500 kw.; in these sizes it is hard for steam engines to compete with Diesel engines, unless fuol oil prices are excessively high, and coal prices very low, or the exhaust steam is used for heating purposes.

Jan 1, 1917

By W. R. Seyfried

THE problem of extracting alumina from clay and low-grade bauxites has been the subject of considerable interest for some time. The basic reason, of course, lies in the fact that known reserves of high-grade bauxite are not inexhaustible and that the present commercial process cannot successfully cope with low-grade bauxites or clay. Ultimately it may be necessary to use these poorer raw materials for all commercial operations. An unprecedented demand for aluminum during the war emergency and the constantly threatened shortage of imported bauxite caused the United States Government to take an active role in this problem. Through the National Academy of Sciences, the War Production Board and the Defense Plant Corporation, it investigated processes and finally selected four to be used in the construction and operation of four experimental plants. Each plant was to be designed in such a way as to facilitate its incorporation into a larger commercial plant should the need arise. The Chemical Construction Corporation process, or "Chemico" ammonium sulphate process as it is better known, was one of the four selected. The extensive literature and patents on record before the war generally follow one of two process-types depending upon the extracting reagent used. One group uses an acid reagent, the other an alkali. The Chemico process uses an acid reagent. For those interested in other processes described in literature, there is a short bibliography at the end of this paper. The basic steps of all acid extraction processes are: (I) to make the aluminum silicates acid soluble, (2) to separate the released alumina from impurities and insoluble gangue, and (3) to recover the reagent for re-use. THE PROCESS AS PLANNED In April 1941, a group of chemists and engineers of the Chemical Construction Corp. became interested in the problem of extracting alumina from clays and low-grade bauxites and, under the leadership of Mr. Blakeslee Barnes, Vice President and General Manager of the Company, first drafted a process in July of that year-five months prior to Pearl Harbor. The work continued in our research laboratories and with a small pilot plant. By June 1943, the work had progressed to a point where it was possible to apply for a patent on the process which was U.S. patent 2,405,426, granted August 6, 1946. Immediately prior to the development of the Salem plant, the process was envisaged to be as follows: I. The first step was to make the aluminum silicates acid soluble. It was planned: (a) Clay or low-grade bauxite would be roasted at 700 to 800°C (1292° to 1472°F), (b) The roasted ore would then be leached with hot aqueous ammonium bisulphate to form a slurry. In this way the

Jan 1, 1947