Search Documents

By F. L. Toy, C. E. Sims

PNEUMATIC processes for converting molten pig iron to steel were the major producers of steel during the latter half of the 19th Century and until shortly after the turn of the century, when these processes began losing ground to their rival—the basic open hearth process. The first pneumatic process for converting molten pig iron to steel was introduced almost simultaneously by Sir Henry Bessemer in England and by William Kelley in the United States during the decade 1850-1860, but it was Bessemer who pushed it to a successful commercial operation. The process itself is so basically simple that it has not lent itself to many extensive or revolutionary improvements since its inception. During the first 30 yr, numerous' designs of vessel and many modifications of practice were tried before the industry standardized on something resembling current practice. The evolution in construction has resulted in proportions and arrangements based more on mechanical expedience than on metallurgical requirements. Many of the early converters were stationary and had to be tapped similarly to the cupola or open hearth furnace. Such types were used for many years in Sweden and Germany, but the rotating or tilting types were favored in England and the United States. There was evident trouble with bottom tuyeres, becAuse about half of the early designs were constructed for side blowing with tuyeres submerged below the metal-bath surface. Even portable tuyeres, introduced from above, were tried. The principal advance, which made bottom blowing practical, was the invention, in 1863, by Henry Bessemer, and subsequent improvement by A. L. Holley, of a detachable bottom so that the tuyere section could be renewed. In the meantime, it was the demonstration, by Robert Mushet, of the value of manganese in overcoming hot-shortness in converter steel, that made the process metallurgically feasible. At first, only the acid practice was used, and Swedish pig iron, because of its low sulphur and phosphorus, was in great demand. The development of a suitable basic lining, by Sidney G. Thomas and Percy G. Gilchrist in 1876-1879, made the process applicable to the high-phosphorus ores of Europe. From the beginning of the use of the Thomas-Gilchrist process, trouble was experienced in obtaining sufficiently high temperatures in the blown metal, particularly in small heats. It is necessary, of course, to have the low-carbon blown metal at a considerably higher temperature for handling from vessel to ladle to molds than is needed for the molten pig iron. All of the increase in temperature in a pneumatic process must be obtained from the heat of combustion of the elements contained in the pig iron plus that from silicon when ferrosilicon is added. In bottom blowing practice, carbon is almost completely burned, but inasmuch as it cannot be oxidized to a higher state of oxidation than to CO when in contact with liquid iron, only a minor portion of the heat-producing capacity is utilized. Under such conditions, it is not considered to be an efficient source of heat. In the acid practice, therefore, silicon and manganese are the large heat producers, are quickly oxidized, and are efficient fuels. Too much manganese, however, thins the slag greatly and tends to promote excessive slopping or throwing of slag and metal from the converter during the blow. Most operators, therefore, like to keep the manganese content of the iron below 0.60 pct, and thus the main source of heat is the silicon, which must be at least 1 pct and sometimes 2 to 3 pct for small blows such as for castings. Ferrosilicon is sometimes added during the blow to obtain an adequate temperature level. In the basic (Thomas) practice, even more heat is required, because cold lime is added to flux the phosphorus after it is oxidized, and the basic slag must be maintained at a proper temperature. Silicon

Jan 1, 1951

By Potts N. L., Eilerts C. K., Summer E. F.

The second-order, nonlinear, partial- dillerential equation representing the transient radial flow of gas - condensate fluids in reservoirs has been integmted by using finite -dillerence equations and electronic computers. Effect was given to pressure -dependent permeability, viscosity, and compressibility and to distance-dependent permeability. The influence of a second-degree velocity term in the Darcy equation was investigated. Implicit methods were used and practical, convergent solutions were obtained with material balance to less than 6 x 10-4 for recovery of one- hall the reserve at constant flow rate. Integration results provide the productive period of a reservoir for a given constant rate and the fraction of the fluid initially in place that can be recovered in that period. The properties of a lean and a rich fluid are represented in a set of integrations designed to demonstrate the effect of different constant-recovery rates and significant variables emphasized one at a time. INTRODUCTION A method is needed for computing the availability or reserve of a gas in a formation, making use of all technical and engineering information that is pertinent. As a step in this direction, a program for computing transient linear flow1 was developed that utilizes principles of earlier finite-difference computing for a similar purpose2-4 and gives effect to significant pressure- and distance-dependent properties of reservoirs and their contents. The present paper pertains to transient, radial flow of gas-condensate fluids. In the partial-differential equation of flow, effect is given to the variables viscosity and compressibility,5 and also to permeability. Included in the study is the quadratic form of the Darcy equation of flow that has been the subject of field tests6 and that has been applied to a gas with constant properties in transient flow computing. 7 Inclusion in the differential equation of variable coefficients to represent properties greatly complicates the higher derivatives of the equation. Because it was impractical to make a required improvement in certain of the finite-difference derivatives by Taylor-series expansion, five-term derivatives were used in the implicit computing. Related methods were developed that can improve general facility in manipulating finite-difference equations. BASIC EQUATIONS PARTIAL DIFFERENTIAL EQUATION The basic partial differential equation for transient radial flow in the direction of decreasing radius is l_ a(vpr) _? .......(1) r gr at where r = radius, L v = apparent velocity aIong radius, L/t p = density, M/L3 t = time, t Ø = porosity, dimensionless. In this equation, only the porosity is regarded constant. The density is where p = pressure, m/Lt2 M = molecular weight of fluid, m T = constant temperature of fluid, T z(p) = pressure-dependent compressibility factor, dimensionless R = gas Constant, mL2/t2t. The physical boundary of the reservoir is at re, and the producing boundary is defined to be at tq with rq = re /200. By definition,

Jan 1, 1966

By D. Torrey

Considering the two great interests of to-day, in iron upon the one hand and steel upon the other, and recognizing with measurable distinctness the peculiar fitness of each for special services to which they are applied, the proposition to unite the two metals in combination, to bring into simultaneous use the peculiar advantages which each offers, has great attractions. The limited success which has been attained by trying to bring about such combinations of the two metals through the use of fluxes in welding, has led to the general adoption of the opinion that an effective union of the two metals is impracticable, or to the view that if practicable it would have but limited commercial value. Such opinions are, I think, premature and erroneous, and having gained some knowledge of the character and value of the "Wheeler process" for welding iron and steel without the use of fluxes, I submit the following observations and opinions of the matter for your information, with the hope of eliciting such a discussion of the subject as it may require. The principle of the invention is to bring the two metals simultaneously to a welding heat in one pile, and then to manipulate it.

Jan 1, 1879

By J. S. Kirkaldy, R. J. Brigham

AS part of a program to investigate the diffusive properties of dilute ternary austenites we have made a determination of the effect of chromium on the activity of carbon in ? iron. Samples of pure iron and Fe-Cr alloys were simultaneously equilibrated at 1000°C with atmospheres of controlled CO/CO2 ratio following the procedures of Darken and Gurry 1 and smith.' The 0.020 in. thick samples were analysed for carbon by microcombustion analyses3 to yield a set of isoacti-vity curves. The latter were converted to activity coefficient (standard state at infinite dilution) plots by combination with Smith's data2 for the activity of carbon in pure iron. Table I shows the compositions of the base alloys used while Fig. 1 shows the experimental results superimposed on a set of curves generated by the relation In?C=6.9NC- 10.7 Ne In the notation of wagner4 the interaction parameter is the second coefficient on the right, Sgr = - 10.7 This can be compared with a rather inaccurate value deduced from the transient equilibrium diffusion data of Kirkaldy et al.' as The authors are indebted to the American Iron and Steel Institute for financial support. This material is condensed from a B.Sc. Thesis submitted to Mc-Master University by R.J.B.

Jan 1, 1963

By Heinrich Freyn

THE American iron and steel manufacturer finds himself to-clay barely at the threshold of enormous possibilities for practicing rational economy in the use of fuels. The fuel cost is by no means the smallest of items which enter into the cost of manufacture of iron and steel products, but the great wealth of this country in high-grade fuels, together with a protective tariff, has heretofore made fuel economy relatively unimportant. In Germany, the use of raw coal for the purposes of iron and steel manufacture has been all but abandoned and large sums of money, formerly irrevocably wasted, are now being saved. When scanning the literature of this country devoted to the application of gas power, but little information will be found on a subject which, however, is destined to become of considerable importance in the United States, namely, the use of coke-oven gas for the generation of power in gas engines. This lack of information can be traced to the fact that the regenerative by-product coke oven with its large amount of surplus gas is still far from having attained in this country the universal application which it has found in Europe. This statement needs hardy any corroboration other than the evidence of statistical investigations made by E. W. Parker of the United States Geological Survey, according to which only approximately 25 per cent. of the total coke produced in this country in 1912 was made in by-product coke ovens, whereas 75 per cent. was produced in bee-hive ovens. This entailed the enormous loss of over $80,000,000 in non-recovered by-products, such as gas, tar, and ammonia, without considering the substantial loss due to the non-recovery of benzol from the coal. There are two more or less distinct fields of application of the by-product coke oven: one, to furnish as the main product metallurgical coke of specified quality, and surplus coke-oven gas as the by-product, and the other, to carbonize high-volatile coals, and thus produce as the main product large quantities of gas, high in heat value and rich in illuminants, adapted primarily for domestic heating and lighting, while domestic coke becomes the by-product.

Jan 4, 1914

By Sherman L. Pease

An inexpensive and relatively rapid method that can be used by field crews is described. Fluid movement is determined by releasing a tracer (dye) in the well at a predetermined level and, after an interval of time, sampling the well fluid at another level. The testing equipment consists of a combined crusher and sampler unit that is run into the well on a wire line. The rate of movement can be calculated from time-volume relationships. Description of Method It is often desirable to determine whether there is occurring any transfer of fluid from point to point in a shut-in well, and, if so, to measure the rate of movement. When it is desired to examine a large number of wells for possible "thief" sands, the time and expense will be considerable unless the method used is inexpensive and rapid. After experimentation with several possible solutions to the problem, the Production Department of the Shell Oil Co., Inc., developed the apparatus described herein, which has proved satisfactory. Routine operations with it can be carried out by field production crews with a minimum of technical supervision and with negligible investment in equipment. The method is based upon releasing a suitable tracer in the well fluid at a known level, and recovering a sample of well fluid at another level after a measured interval of time. Repetition of this process with different time intervals between release and sampling gives the necessary data. For purposes of illustration, the setup for measuring migration of fluid in an upward direction is described in the following paragraphs. The arrangement of equipment is shown diagrammatically on Fig. I. The elements of the combination unit are the tailpiece, the crushing device, the spacer and the sampling device. The lengths of the tailpiece and spacer are varied to place the crushing and sampling devices in the desired positions in relation to the sands being tested. The crushing device breaks the glass bottle containing the tracer when the tailpiece strikes the bottom of the well and the tension on the sand line is slackened. Because of the open construction of the crushing device, the tracer is quickly and completely disseminated in the well fluid. The sampling device is a suction bailer, which obtains a sample of the fluid surrounding the perforated nipple just before the unit is picked up off bottom. The sample is retained in the barrel by the ball valve for examination at the surface. Normally, on the first run into a well, the sample is obtained near the releasing point of the tracer, and thereafter samples are taken near the base of the upper sand if migration is indicated by the dilution or absence of the tracer in the initial sample. The length of the time interval between the releasing of the tracer and the sampling of the well fluid is varied for successive runs, attempting first to establish the rate within limits and then to define it more accurately by additional runs if necessary.

Jan 1, 1946

By Sherman L. Pease

An inexpensive and relatively rapid method that can be used by field crews is described. Fluid movement is determined by releasing a tracer (dye) in the well at a predetermined level and, after an interval of time, sampling the well fluid at another level. The testing equipment consists of a combined crusher and sampler unit that is run into the well on a wire line. The rate of movement can be calculated from time-volume relationships. Description of Method It is often desirable to determine whether there is occurring any transfer of fluid from point to point in a shut-in well, and, if so, to measure the rate of movement. When it is desired to examine a large number of wells for possible "thief" sands, the time and expense will be considerable unless the method used is inexpensive and rapid. After experimentation with several possible solutions to the problem, the Production Department of the Shell Oil Co., Inc., developed the apparatus described herein, which has proved satisfactory. Routine operations with it can be carried out by field production crews with a minimum of technical supervision and with negligible investment in equipment. The method is based upon releasing a suitable tracer in the well fluid at a known level, and recovering a sample of well fluid at another level after a measured interval of time. Repetition of this process with different time intervals between release and sampling gives the necessary data. For purposes of illustration, the setup for measuring migration of fluid in an upward direction is described in the following paragraphs. The arrangement of equipment is shown diagrammatically on Fig. I. The elements of the combination unit are the tailpiece, the crushing device, the spacer and the sampling device. The lengths of the tailpiece and spacer are varied to place the crushing and sampling devices in the desired positions in relation to the sands being tested. The crushing device breaks the glass bottle containing the tracer when the tailpiece strikes the bottom of the well and the tension on the sand line is slackened. Because of the open construction of the crushing device, the tracer is quickly and completely disseminated in the well fluid. The sampling device is a suction bailer, which obtains a sample of the fluid surrounding the perforated nipple just before the unit is picked up off bottom. The sample is retained in the barrel by the ball valve for examination at the surface. Normally, on the first run into a well, the sample is obtained near the releasing point of the tracer, and thereafter samples are taken near the base of the upper sand if migration is indicated by the dilution or absence of the tracer in the initial sample. The length of the time interval between the releasing of the tracer and the sampling of the well fluid is varied for successive runs, attempting first to establish the rate within limits and then to define it more accurately by additional runs if necessary.

Jan 1, 1946

By W. R. Toeplitz

Probably a more descriptive title would be "Much Ado About Nothing." By "nothing," of course, I refer to the porosity which is the main feature of this type of bearing. Porosity has a decided effect on the manufacturing techniques, the structure and physical properties, the oil content, and on the installation and service of oil-retaining porous bronze bearings. A simple curve can be drawn by plotting specific gravity along the abscissa and percentage of porosity by volume on the ordinate. A bronze composition, analyzing 89 Per cent copper, 9.75 Per cent tin, and 1.25 per cent graphite, has an absolute solid specific gravity of 8.5. At this specific gravity, of course, occurs the point of zero porosity. Conversely, at loo per cent porosity, the specific gravity is zero. A similar curve can be drawn for bearings impregnated with oil; the only change being that the specific gravity at loo per cent oil will be 0.89 if we assume that that is the specific gravity of the lubricant. The curve is useful in determining the oil content by volume for any specific gravity. The normal range of oil content for porous bronze bearings of this composition is from 35 to 16 per cent, which is in the specific gravity range of from 5.8 to 7.3. In addition to the amount of porosity, the type of porosity is important. The first consideration here is that the porosity must be intercommunicating. This can be determined by a number of simple tests. The first method, which is very accurate, is to extract the oil in the bearing by cycling

Jan 1, 1945

By Eckley B. Coxe

Having been appointed, on February 19th, 1890, a member of the Commission created by the Legislature of Pennsylvania for the purpose of investigating the " Waste of Coal Mining, with the View to the Utilizing of the Waste" (waste in this case referring specially to the small sizes of anthracite heretofore thrown away), my attention was naturally directed to the mash economical method of burning these small sizes.* Although I had been Familiar with the burning of anthracite for • many years, I found when I came to study the matter carefully that I was far from thoroughly understanding it, particularly with reference to the hurning of the smaller sizes, and that the literature of the subject, which was not very extensive, had more of a tendency to confuse than to enlighten me. I began therefore to investigate the subject so as to arrive if possible at some definite principles applicable to the question. With the aid of my assistant, Mr. John R. Wagner, I began at Drifton a series of experiments upon the burning of small anthracites. We first erected a small furnace with a grate 3 feet long and 2 feet wide, with which we experimented about two months. From the information thus acquired, we designed and built another furnace of about the same size, which gave us facilities for extending our investigations still further. After experimenting several months with the second furnace, we built a third one, which was much larger, having a grate area of about 68 square feet, which was exactly the size of the grate used in the boiler-plants of' Coxe Bros. &

Jan 1, 1894

By R. W. Freeman, L. L. Tavlarides

The experimental methods used in obtaining kinetic data for solvent extraction systems can affect the validity of the results The method of contacting the two liquids should allow for accurate determination of the surface area, hydrodynamics, and diffusional processes The appropriateness of the Liquid Jet Recycle Reactor is discussed and the modelling of the mass transfer and chelation reaction is presented The LJRR is used to investigate the chelation of copper by LIX65N in toluene from aqueous copper sulfate sulfuric acid solutions The ranges of experimental variables are Copper, 1 8-13.8 g-dm-3, sulfuric acid 0-1.6 g-dm-3, LIX65N, 0 1-1.0 mol-dm-3 Data on the initial rate of copper chelation at the interface is generated Nonlinear regression analysis shows that the following expression adequately describes the data within experimental error.

Jan 1, 1981

By A. Grant Elliot, H. W. Lavendel

qualitative picture has been developed to describe the oxidation behavior of TaSi2-coated tantalum and CbSi2-coated columbium. These systems have a significantly lower inherent oxidation resistance than MoSi2-coated molybdenum does. This stems primarily from the fact that Ta2O5 and Cb2O5 are nearly as stable thermodynamically as SiO2, whereas MoO2 or Moos are not. Further, diffusion of silicon in the Ta- and Cb-Si system is considerably slower than in the Mo-Si system. These ,factors prohibit the mechanism of selective oxidation of- silicon which accounts for the oxidation resistance 01- MoSi2-coated molybdenum. The silicide can be stabilized by adding suitable Modifiers which increase the thermodynamic stability of the silicate formed during oxidation. Modifiers, such as aluminum, can be inroduced into solid solution in the coating. in controlled amounts through proper selection of the source in the pack cementation process of coating fov~rzatiorz. Addition of aluminum to TaSi2, coatings on tantalum was effective in moderately increasing the oxidation resistance. EXTENSIVE experimental work and analysis have established the nature of the oxidation behavior exhibited by MoSi2- and MoSi2 -coated molybdenum-base alloys, and defined the conditions for maximum protection against oxidation of the substrate.'-* The oxidation resistance of MoSi2 in the temperature-pressure range of 1100°C-PO2 > 10-5 atm to 1900°C— PO2 > 10-1 atm is due to the formation at the surface of a continuous film of SiO2 which results from selective oxidation of silicon. Under the prevailing kinetic conditions, this film is stable toward the molybdenum silicide with which it comes in contact. Initially molybdenum oxidizes also, but it forms volatile species. SiO2, however, nucleates and grows as a condensed phase. Once a continuous film of SiO2 has formed, the oxidation rate falls to that observed for the oxidation of pure silicon indicative of diffusion through the oxide film as the rate-controlling mechanism. This oxidation behavior is of course highly dependent upon temperature and oxygen pressure. Bartlett and Gage13 and Bartlett, McCamont, and Gagelb define precisely this dependence in terms of the oxygen partial pressures and silicon diffusivities required to support a stable SiO2 film. At low temperatures (near 500°C—the "pest" region) silicon diffuses too slowly to be selectively oxidized. Hence, molybdenum and silicon oxidize readily in proportion to their stoi- chiometry. At high temperatures and low pressure, SiOz dissociates to form volatile SiO(g), and a protective film cannot be maintained. Application of the MoSiz/Mo system is limited to temperatures below 1900oC, the eutectic between MoSi, and MO5Si3.5 The oxidation behavior of MoSi2-coated molybdenum is essentially the same as that outlined above with the exception that the MoSi2 is not in equilibrium with the molybdenum substrate. At the temperatures under consideration silicon will diffuse rapidly into the molybdenum eventually converting the coating to MosSi3.4 The rate constant for subsequent decomposition of Mo5Si3 into Mo3Si plus silicon, and/or the diffusivity of silicon through Mo3Si then becomes low enough to allow active oxidation of both molybdenum and silicon with subsequent degradation of the specimen. A stable silica film can be formed but at temperatures and/or oxygen partial pressures higher than those required with MoSi2 present as a source of si1icon.l, 4 Because of the similarity between the silicides of molybdenum and those of columbium and tantalum one would expect similar oxidation behavior for coatings in the respective systems. This is not entirely the case, however, as shown by the experimental results reported herein. Regarding tantalum and columbium disilicide coatings on tantalum and columbium substrates, respectively, the oxygen arriving at the surface of the coating partitions itself nearly equally between the metal and the silicon, and a two-phase oxide layer (Me2O5 plus SiO2) is always formed. The diffusion of silicon in the tantalum and columbium silicides is relatively slow, compared to that in the molybdenum silicides, which further enhances this equipartitioning of oxygen. Thickening of the coating during service by inward diffusion of silicon into the substrate is correspondingly slow, and the effective thickness of the coating at the roots of cracks and defects is only slightly changed providing high probability for premature coating failure. Furthermore, the SiO2 glass that is generated is not thermodynamically stable with respect to the coating. The metal silicide tends to reduce the SiO2 liberating either free silicon or SiO. The situation can be improved by suitably modifying the coating such that the stability of the protective glass which is generated during service is increased. Thus, selective oxidation of silicon and the modifying agent will occur, and the silicide coating will not tend to reduce the oxide layer. Modifying agents can be introduced into the coating by the pack cementation process. Using sources containing the modifier at controlled chemical potentials allows control of the coating composition. Partially substituting aluminum for silicon in TaSi2 coatings by forming a Ta(Si,Al)2 solid solution was effective in moderately increasing the oxidation protection.

Jan 1, 1968

By Charles M. Packer, Oleg D. Sherby, Roy H. Johnson

Originally round tensile specimens of a eutectic Zn-A1 alloy develop elliptical cross sections during superplastic deformation. This observation, coupled with a detailed study of the microstructure and preferred orieniation, suggests that crystallographic slip and continuous grain boundary migration or re-crystallization are important processes during super-plastic deformation. In spite of the extensive activity in superplasticity1-15 and the numerous explanations proposed, no single model has had universal acceptance. It has been established, however, that the general requirements for superplastic extension of two-phase alloys include an extremely fine, stabilized grain size of the order of a few microns, a temperature about equal to or greater than one-half the melting point, a critical range of strain rate, and a similarity in the mechanical strength of the major phases. The proposed models can perhaps best be characterized in terms of the important phenomena associated with them. These phenomena include: phase instability,1 diffusional creep by volume diffusion3 or grain boundary diffusion4,5 slip and continuous grain boundary migration or recrystalliza-tion,= grain boundary Sliding,7-9,13,14 and dislocation glide.'5 In this paper, experimental observations will be reported which support a model involving slip and continuous grain boundary migration or recrystalliza-tion. Specifically, a correlation will be made between this model and the development of elliptical cross sections as originally round specimens are superplas-tically deformed. For the most part, superplasticity studies have been conducted with eutectic or eutectoid alloys. Probably the most thoroughly studied material has been the monotectoid Zn-A1 alloy.1,2,6,12,13,15 No attention to the eutectic Zn-A1 alloy has previously been reported, and the results discussed in this paper represent part of a general study of the superplastic properties of this alloy. MATERIALS The alloys used in this investigation were prepared by melting appropriate quantities of 99.99+ pct A1 and 99.999 pct Zn in air, mixing, and pouring into a water- cooled stainless-steel mold. Wet-chemical analysis was conducted with each heat of alloy prepared, using the procedure of Fish and smith.16 The composition of the eutectic alloy was 95.1 wt pct Zn. Ingots about 2 in. thick were rolled to 0.4-in. plate at about 300°C with a reduction of 5 to 10 pct per pass. Specimens were machined from the plate with the tensile axis parallel to the rolling direction. The specimens were round, with 0.150-in.-diam, 1.25-in.-long gage length, and 0.25-in.-diam threaded grip sections. EXPERIMENTAL PROCEDURE Specimens were mounted inside a uniform-temperature quartz tube which was surrounded by a double elliptical radiant furnace with a 12-in.-long uniform-temperature hot zone and a low thermal capacity. The tube extended through the top and bottom of the furnace and permitted rapid quenching of the loaded specimens when quickly filled with cold water at the conclusion of the test. The quench precluded any effects on specimen microstructure from a normal, slow cool. Constant stress was applied to test specimens by suspending a load on a constant stress cam of the type described by Hopkin.17 The design of this cam permitted application of a constant stress for elongations up to 200 pct. For greater elongation, approximately constant stress conditions were maintained by systematically reducing the load manually. RESULTS As part of an investigation of the superplastic properties of the eutectic Zn-A1 alloy, evidence was obtained for the development of elliptically shaped cross sections as originally round specimens were extended. For example, after an elongation of about 100 pct, a round specimen with an initial diameter of 0.150 in. became elliptical with major and minor axis of 0.128 and 0.88 in., respectively. Photographs are presented to illustrate the ellipticity developed during superplastic deformation, Fig. 1. The specimen shown was deformed at a stress of 500 psi, at a temperature of 285°C, and a strain rate of 2.28 x 10-2 min-1. The strain-rate sensitivity exponent* was measured at *The strain-rate sensitivity exponent, m, is defined as d In o/d In c where o is the steady-state flow stress and E is the strain rate. this temperature and in the strain rate range 10"3 to 10-1 min-1 was found to be about 0.5. This value is typical of those observed with superplastic materials. The material studied exhibited negligible strain hardening during superplastic deformation, the creep rate remaining constant under constant stress and temper-

Jan 1, 1969

By A. W. D. Hills

This paper describes the development of a generalized integral-Wofile method for the analysis of heat transfer dwing solidification. The method is extremely flexible, and can be applied to a wide range of situations. This flexibility has been achieved by characterizing the solid metal layer in terms of two parameters, and by developing two simultaneous nonlinear differential equations for these parameters in terms of the heat fluxes crossing the boundaries of the solid layer. The use of these equations is illustrated in a series of examples which involve the solidification of pure metals at zero superheat cooling under different conditions. The simplicity with which the method can be extended to treat more complicated jwoblems is illustrated in a further example which involves natwal convection effects in the liquid metal. ThE rate at which molten metal solidifies in an industrial casting process, and the structure of the cast product, are both controlled by the rate at which heat can be removed from the casting. A knowledge of heat transfer rates is thus essential to the control of the process and to the control of the structure and soundness of the final casting. Heat transfer rates during real solidification processes cannot be predicted by formal mathematical techniques, however, because nonlinear boundary conditions are involved. Approximate methods are normally used, and these have included electrical and hydraulic analogue techniques, finite difference methods, and the integral-profile method. Considerable effort has been devoted to the development of the first two techniques, but the integral-profile method has been used very little so far. This is unfortunate because the method is capable of providing relatively accurate solutions for the heat transfer equation during solidification without involving large amounts of computer time. A further advantage of the method is its flexibility, although this is not apparent from the integral-profile solutions that have been developed to date. These solutions have been derived for the solidification of molten metal at zero super-heat under cooling conditions involving either a constant heat flux from the cooled surface;' a constant heat transfer coefficient at the surface,'-3 or a specified variation in the surface temperature.4,5 A generalized integral-profile method is presented in this paper which can be used to predict unidirectional solidification rates under a very wide range of more realistic cooling conditions. The use of the method is illustrated in a series of problems involving pure metals, or skin forming alloys, solidifying at zero super-heat. However, the principal advantage that this method has over the previous integral-profile methods is the ease with which it can be extended to treat more complicated solidification problems. This is illustrated by considering a problem in which super-heat is liberated from the liquid metal by natural convection during the solidification process. In the final section of the paper the generalized method is compared with previous methods used to predict solidification rates and its extension to more complicated solidification problems is briefly discussed.

Jan 1, 1970

By John W. Langley

The unsatisfactory character of most, if not all, of the processes for the direct determination of alumina in the presence of iron and phosphoric acid, and the sharpness with which both the iron and phosqhoric acid can be determined, have led chemists to rely mainly

Jan 1, 1892

By J. Ostachowicz, B. Holynska, M. Lankosz

The paper presents an analyzer and the method for the continuous determination of weight percentage of ore grains with diameter smaller than 75 µm in mineral slurries. The method is based upon the measurement of characteristic x-rays of copper excited by primary radiation of two different energies 16.5 keV and 60 keV from Pu238 and Am241 sources respectively. Additionally the backscattered primary radiation is measured in order to correct the variations of the solids content in the slurry. Since the particle size distribution of slurry can be described by the Rosin-Rammler formula, some calculations have been carried out in order to evaluate the influence of distribution parameters upon the results of the measurements of weight percentage U75 of particles smaller than 75 µm. The influence of solids content and of the copper concentration variation on the results has been also evaluated.1 It resulted from the calculations that the ratio rl/rz, where rl and r2 are the relative intensities of copper characteristic x-rays excited with 16.5 keV and 60 keV photons respectively does not depend on the copper content within the range 1 % to 4% of copper and is slightly dependent on the solids weight fraction and its chemical composition. The change of the dispersion parameter of the Rosin- Rammler distribution from 0.5 to 0.9 results in a change of value of U75 of approximately 3.0%. The results of calculations have been confirmed by the results of laboratory experiments. Therefore, a prototype of industrial analyzer for continuous determination of weight percentage of particles smaller than 75 µm has been designed and made. Its schematic drawing is shown in [Fig. 1]. Slurry is flowing down through steel flow-cell of the length equal to approx. 2 m. In the center, two XRF measuring heads (1) and (2) are located. Each of the heads comprises a rigid waterproof cover (3) with the mylar window (4), in which a proportional counter of resolution 15% for 6.4 keV is mounted with a preamplifier (5). The low- energy isotope source (6) is centrally located above the detector

Jan 1, 1980

By R. T. DeHoff, L. J. Buteau, J. Kronsbein

Network topology is introduced and used to describe sinter bodies at various stages of the sintering process. The matrices of incidence, loop-branch. tree-branch, and cut-branch are constructed and their relationship to the three-dimensional void space and the common two-dimensional bounding surface is established. The sintering body is assunzed to remain connected but this is not so with the void space. The topological invariants known as Betti numbers are related to this observed fact and provide parameters which measure the progress of the sintering process. They are extracted from the matrices by means of known algebraic operations. Experimental procedures are given which permit actual construction of the various matrices and determination of the Betti numbers by serial sectioning of the sinter bodies. A sinter body is produced by exposing a large number of metallic particles (0.00001 to 0.3 in. diam) to a temperature that is near but below their melting point. When these particles are maintained at such a temperature for a sufficient length of time, it is found that the interparticle contacts become welded. As time increases, these welds, often referred to as necks, grow. All of the space between the particles constitutes a single connected void; an ultimate consequence of sintering is the breaking up of the void into separated parts. A mathematical apparatus for describing the geometric characteristics of a sinter body at each stage of the process was first proposed by F. N. Rhinesl when he introduced the application of topology to this problem. He described the sinter body in terms of one of its topological invariants, the genus. The most important advantage of a topological description is invariance with respect to continuous deformations. This means that particle sizes and shapes need not be considered, resulting in considerable simplification and generalization of the geometric description. In the case of a sinter body, wherein the internal geometry is particularly complex, the simplification provided by topological concepts is absolutely essential. The important parameters in the Rhines model are the number of particles and the interparticle contacts. The invariant considered called genus is given by Euler's formula for the connectivity of two-dimensional surface of the sinter body. This surface includes the pore-solid interface. The Euler formula is G = C - P + 1 [1] where C = number of interparticle contacts, P = number of particles, and G = genus of the surface bounding the sinter body. In topology the term genus may be used to mean the number of self re-entrant cuts that can be made on a closed surface without dissecting it into more than one connected surface. Its use is restricted to the surface and does not apply to the three-dimensional volume enclosed or excluded by it. In the case of sintering, the volume enclosed by the surface is defined as the sinter body; the volume excluded will be referred to as the void space. There is an intrinsic reason for using genus as a characteristic number associated with a sinter body. The genus is related to the Gaussian curvature by the integral of the product of the principal curvatures taken over the entire surface of the sinter body, as given by

Jan 1, 1965

By Richard Klimpel

This paper describes the effects of slurry viscosity on the selection-for-breakage and breakage distribution parameters in the wet grinding of ores. A series of experimental tests were run on laboratory scale ball mills. Slurry viscosities were modified by varying the solids/water ratio with and without the presence of selected chemicals. Very consistent and predictable correlations are shown to exist. The grinding parameters were calculated using a computerized back-calculation technique developed by Klimpel and Austin. Industrial scale circuit calculations and preliminary plant trial data suggest that considerable increases in throughput and/or fineness of grind can be achieved through the judicious use of chemical additives.

Jan 1, 1977

R. B. BRinsmade, Ixmiquilpan, Hgo., Mexico (written discussion").—how far ahead of the United States are the self-governing British colonies in their application of economic democracy is well illustrated by Mr. Godson's paper. To prove this, I need quote only two of his assertions, the italics being mine: "lt is a stern fundamental principle that a11 natural resources are the inalienable property of the crown.'' "The right to a claim should only exist as long as it is worked or taxed to insure work. Once depart from that sound maxim, there results improper control of the natural resources of the country, which primarily belong to the people." These assertions formed the basis of my criticism1 of Dr. Raymond's paper in 1913, and they should be inscribed in letters of gold above the entrance to the office of every county recorder in the United States. I venture to assert that the existing United States mineral land laws are essentially unfair to the nation and a hindrance to the legitimate miner, because they fail to embody the above quoted principlca; and this applies both to state laws east of the Mississippi and to federal laws in the West. That these laws favor the forestaller and the monopolist, defraud the government of its fair share of the profits of mineral production, and tend to industrial feudalism must be evident to any competent unbiassed observer. The fact that no serious political movement arose to change them, until the conservation agitation of the last decade, may be largely explained by two salient conditions. First, as stated by President Winchell, "for a long time there was such a vast surplus, or excessive amount of unwanted, undesirable land in the West that the land offices did not scrutinize the claim sought to be located;" second, that the millions of individual farm owners throughout the country could easily be aroused, by the special pleaders hired by the great land speculators and monopolists, to use their vast political power for the suppression of any statesmen striving to incorporate in our semi-feudal land laws any such principles as those quoted from Mr. Godson. While agreeing with Mr. Godson that a freehold or fee-simple title, if coupled with obligatory continuous work, may have the same practical effect as a lease, it seems to be the experience of the most active and

Jan 1, 1920

By M. Hoch

Equations are derived from statistical considerations to represent the activities of each component of an interstitial solution, and of a compound with a wide homogeneity range as a function of composition and temperature, based on the interaction energies between the various components, Eij. The equations are checked on the binary systems Fe-C, Ta-H, and Y-H, the ternary systems Ti-O-H, liquid Fe-C-0, and the compounds TiO, MnO, COO, and YH,. In all cases the present model represents the experimental data well. THE aim of this paper is to derive from statistical considerations the thermodynamic behavior of non-substitutional solid solutions. "Nonsubstitutional solid solution" means either an interstitial solid solution (carbon in iron, oxygen and hydrogen in hexagonal and bcc titanium, and so forth) or deviation from stoichiornetry in compounds (introduction of vacancies—removal of atoms in one or both lattice sites of compounds FeO, MnO, TiO, NbO, YH2). wagnerl and Fowler and Guggenheim considered the theory of compounds with small deviation from stoichiometry; Anderson includes larger deviations from stoichiometry, the defect being present in one component only, as vacancy and interstitial. Rees considers only vacancies in one of the components and introduces various kinds of sites for the component where the defect occurs; the various sites interact with different energies, thus giving isotherms with two or more plateaus. Both Rees and Anderson are mainly occupied in determining the limits of two-phase regions, and the defect interaction energy is determined from the critical point. Darken and Gurry5 gave a brief treatment of carbon solution in iron; Speiser and spretnak calculated the configurational entropy for binary interstitial solid solutions by assuming that each interstitial atom in the solution excludes a certain number of neighboring interstitial sites from occupancy. Use will be made of this concept later. Hoch et al treated transition metal oxides of the NaCl-type structure, and also oxygen solution in titanium.' The main aim was to determine the behavior of the activity of one of the components as a function of the composition in the single-phase region. In the present paper, the various interaction energies are discussed in detail and the similarity between interstitial solid solutions and deviation from stoichiometry in ionic compounds is shown. Both types of systems have in common that at least on one kind of lattice site only one kind of atom occurs; this gives a fixed frame to the system, permitting a much easier statistical treatment than for the substitu-tional solid solutions. (The theory is also applied to ternary systems.) The difference between an interstitial solution and deviation from stoichiometry can be explained as follows. In an interstitial solution in the pure or standard state the host atom or host structure is present alone and all the interstitial sites which are going to be filled when the interstitial atom is introduced are empty. The interstitial solution is now created by introducing atoms into this empty lattice. In the deviation from stoichiometry, both kinds of lattice sites are already occupied in a special fashion (all lattice sites occupied, or the same fraction of lattice sites empty, or one kind completely filled, the other only two-thirds). Deviation from stoichiometry removes atoms from lattice sites, adds them, or removes atoms from one kind of lattice site and introduces them on the other lattice site. Though both cases (interstitial solution and deviation from stoichiometry) lead almost to the same equations, they are treated separately. The treatment given below corresponds to the "regular solution"10 treatment of substitutional solid solutions. Speiser and spretnak's6 treatment is similar to the athermal solution in the substitutional use. a) INTERSTITIAL SOLID SOLUTIONS Theory. It will be assumed that there are N lat-tice sites occupied by the host atom (denoted by 1). Corresponding to those N lattice sites there are N octahedral and EN tetrahedral interstitial sites. If only one kind of interstitial atom is added, this in-

Jan 1, 1964

By James P. Roe

Those who deem the subject of this paper an old and superseded one may recall with advantage the words of the great proverb-maker, bidding us to seek the new in the ashes of the old. The manufacture of wrought-iron began with the small hearth built upon an eminence, and relying on the wind for blast. Next came, either the hearth about 12 in. in diameter by 2 ft. in height, blown by a man operating two goat-skins for bellows, or, a hearth of greatly varying diameter and about 10 R. high, depending for its blast upon natural draft. The former appeared in India, the latter in Burmah; and both were in operation until quite recently, though their origin is lost in prehistoric times. The Catalan forge was the evolutionary descendant of the foregoing, and the parent of the Blase-ofen, which in turn led to the high bloomary or " StÜckofen," the father of the blastfurnace, as a producer of cast-iron. The production of cast-iron checked the growth of the direct processes; and led to the introduction of various hearths, such as the Walloon, for low-silicon irons; and the South Wales process, combining the run-out fire with the finery, for higher-silicon irons. Some of these are still in operation in localities possessing the necessary raw materials; and their product is used for purposes requiring wrought-iron of exceptional quality, the supply of which is still smaller than the demand.

Jan 1, 1906