Search Documents

By J. H. Palm

Experiments have shown12 that the formula -S = St - (St - Se')e ne [1] expresses very well the relation between the true stress S and the true form monotonic deformation of plastic metals in single tension and compression (Fig 1). St (asymptotic or final stress), Se' (threshold stress) and ne (characteristic or specific strain) are constants, the significance of which immediately follows from Fig 1. Only at the initial stages of deformation the experimental curve runs below the theoretical curve. This may be due, at least partly, to the uneven stress distribution caused by the anisotropy of the crystals. It is now obvious that a similar formula H = Ht- (Ht- He)e ne' [2] might be valid for the relation between the hardness and the strain. The hardness can be only a function of the strain and must therefore be independent on the hydrostatic tension present in the neck during straining. Hence, if Eq 2 is correct it will also represent the relation between hardness and strain in the middle section of the neck, the strain of which is generally assumed to be almost or fully homogeneous. For aluminum, copper, and several copper alloys it is indeed observed that Eq 2 agrees very well with the experimental Vickers hardness-strain relation from zero strain on up to the strain at fracture. Moreover nc' is, for several metals fairly equal to nc- Hence H = C1 + C2S [3] C1 and C2 are constants during uniform uniaxial tension. Eq 3 was also obtained for copper by Voce.3 According to Hencky's theory4 the ratio of the Brinell or Vickers hardness and the yieldstress (expressed in kg per mm2) of a non-strainhardening metal is approximately equal to 2.8. If Eq 1, 2 and 3 are correct the ratio Ht/S, must accordingly be the same for all plastic metals and be equal to 2.8. It is now experimentally established that this ratio varies between 2.7 and 3.1 with a mean value of 2.9. Taking into account that Ht and especially St can be obtained only by extrapolation from the range of rather low strains, the agreement with the theory is very satisfactory. References 1. J. H. Palm: Appl. Sci. Res. Al (1948) 198. 2. E. Voce: Jnl. Inst. of Met. (1948) 74, II, 537. 3. E. Voce: Metal Treatment (1948) 15, 53. 4. H. Hencky: Zlsch. f. angew. Math. and Mech. (1923) 3, 241.

Jan 1, 1950

By E. R. Force, W. F. Cannon

Many large high-grade manganese deposits occur in marine-transgressive sedimentary sequences deposit fed on stable platforms, although the manganese mineralogy varies from carbonate to oxide facies and host lithologies vary from carbonate- to clay-dominated sections. Examples include the Nikopol and related deposits of the Soviet Union and Groote Eylandt, Australia. Recent work has shown that high sea-level stands are synchronous with stratified and stagnant oceans. We suggest that during transgressions and consequent anoxic events, the anoxic deep waters rich in dissolved manganese were dilute ore-forming fluids. Manganese was precipitated on the oxidized side of oxidation and alkalinity interfaces on shallow shelves. Where the precipitate was preserved, manganese ac- cumulated into ore deposits. Sedimentary manganese deposits have not been widely explored for in North America, nor are they always obvious in outcrop. Large areas of North America are underlain by rocks that we consider broadly favorable for such manganese deposits, and the disparity between the high potential but significant reserves of the United States is difficult to reconcile. Important undiscovered deposits seem likely. An area of Cretaceous rocks in South Dakota is presented as a possible location for a United States deposit analogous to foreign deposits described herein.

Jan 1, 1983

By J. H. Bowden

The water-hoisting tanks herewith illustrated have been designed for removing large quantities of water from recently-flooded mines, through their hoisting-slopes, with rapidity proportional to the capabilities of the hoisting machinery available, the tanks being adaptable to slopes of small sectional areas and varying pitches. The following features may be of interest to those operating mines liable to be flooded. 1. The arrangement of doors on each tank by which it may be automatically filled by immersion at any point on the varying pitch of a slope, the water being retained while hoisting on the flat as well as on the steep pitches, and quickly and autoniatically discharged at the top. 2. The arrangement, in connection with the above-mentioned doors, of side-wheels over the rear wheeh of each tank and of sidedumping tracks at the top of the hoist, for the automatic emptying and quick return of the tank. 3. The arrangement of two or more tanks, one in front of the other, so as to give as large a capacity in a single hoist as the enginepower will permit, yet without making any tank too large for the sectional area of the slope, or of unwieldlp length, or of such a shape that it cannot easily pass over vertical curves; and without concentrating too much weight on any one pair of wheels or on any point of the track. The details of construction and method of operating are shown by the accompanying sketches (Figs. 1 and 2), and the following more detailed description. At the end of each tank is a large iron door of almost the full size of the end of the tank, opening inwards, so that when immersed the tanks fill almost instantly. To provide for holding the water while it is hoisted up flat pitches, a wooden door is attached to the front of each tank, opening outward. Each front door is attached to the

Jan 1, 1892

By John Birkinbine

An item of considerable importance to the producers of pig-iron is the disposition of the slag or cinder from the blast-furnace; and various plans have been adopted at different works to care for the rapid accumulation of this generally waste material. The charge per ton of iron made which must be allowed for the care of cinder is sufficient in times of business depression to give plants having facilities for disposing of their slags an advantage over others less favorably arranged, and to allow iron to be produced profitably in the one case and prevent a profit in the other. The varied methods employed and the means of conveyance utilized need not be detailed. It is sufficient to say that the large outputs of American blast-furnaces, and consequent rapidly augmenting dump-piles, have brought into general favor the use of cars carrying the slag in a liquid condition. The advantages of this method are the prompt removal of the slag, the reduced space occupied by the dump-piles, and the facility of converting the slag into such forms for use as may be desired. The progress in iron-manufactlire is also marked by a more general adoption of methods by which molten metal is carried in vessels away from the point of its production; and, anticipating the prospective advance in pig-iron manufacture, it does not seem unreasonable to prophesy the early abolition of casting-houses at blastfurnaces, particularly where several are grouped together; or the casting of steel ingots away from the converters or furnaces. In some large blast-furnace plants, the iron is carried molten from the blast-furnaces to the converters or other furnaces. Even where it is cast into pigs, casting-sheds removed from the immediate vicinity of the furnace-stack would, perhaps, be superior to casting in beds in front of the furnaces. The idea of casting-sheds appears to present the following advantages : 1st. The equipment of boilers, hot-ovens, and blowing-machinery could be closely grouped around the blast-furnace stacks, permitting

Jan 1, 1887

By R. V. Wheeler, F. V. Tideswell

The suggestion, which appears to find increasing favor, that the elementary composition of coals should be used as the basis of their classification, makes it important that our methods of expressing this elementary composition should be refined. It is doubtful whether many published ultimate analyses of coals are accurate within 1 per cent. carbon. Many are probably as much as 3 or 2 per cent. in error in carbon. It is, perhaps, not always realized that the extreme variation in carbon content over the range of bituminous coals is but 16 per cent. An error of 1 per cent. in carbon on analysis corresponds therefore with one-sixteenth of the whole range, an amount which is unjustifiable even for the application to commercial needs of a system of classification based on ultimate analysis. For the purposes of scientific research such limited accuracy is of little value. The object of this paper is to examine one important source of error in ultimate analysis, that due to the occurrence in coal of inorganic material, and to emphasize the need for the quantitative measurements (of carbon more particularly) on coals to be rendered independent of their contents of such material. Adventitious Mineral Matter When a determination of calorific value, for example, is made upon a coal, it is customary to correct the measured value with respect to the ash left by the coal on incineration, recording the result as being on an "ash-free basis." It is desirable, before discussing the adequacy of the correction thus made, to demonstrate its validity, which turns on whether the ash is present as an adventitious impurity in the coal and forms no part of the coal substance itself. The inorganic matter associated with coal has originated in several ways1: 1. The "inherent" inorganic materials, occurring as constituents of the plants from which the coal-forming deposits were derived.

Jan 1, 1928

By John M. Hartman

TWO systems are used for heating air in blast-furnace operations: I. The double surface system, in which a cast-iron pipe is heated on the outer surface, and, at the same time, heats the blast from its inner surface. This is simple in operation and gives a continuous effect, but is limited by 1100" F. as a maximum temperature of the blast. 11. The single surface system, by which large surfaces of fire-brick are heated, and air passed over the heated surface, absorbing the heat and carrying it on to the furnace. This system is more comylex than the double surface, as it invoives the reversing of the air and gas every hour and a half. The single surface system has two advantages: 1. The blast can be heated to a temperature of 1800° F. 2. The stoves are indestructible. From recent experience it has been found that 1300" F. to 1400' F. is the best average temperature for economy of coal for safe working. This is equivalent to a saving of 11/2 to 2 cwt. of coal per ton of iron over the extreme limit of cast-iron stoves. Independently of this, it is a strong point in favor of this system that the blast can be raised to a temperature of 1800° F. within an hour when the hearth is getting cold. All furnacemen know the ralue of a hot hearth for quality and quantity of iron. Cooling of a hearth occurs from leaky tuyeres, scaffolds, or heavy burden. When there is not sufficient coal at the tuyeres to seize on the oxygen of the entering air and convert it at once to carbonic oxide, there will not be enough heat to liquefy the cinder. Black cinder and poor iron are the results. The remedy is additional heat from the blast. If the stoves will give 1800" in place of 1100°, it is obvions that the furnaces will get around sooner, and without waiting for a change of burden at the tunnel head to bring extra coal to the hearth. The heat absorption caused by a leaky tuyere will chill the hearth and drive the zone of fusion higher up in the furnace. This loss must be supplied, and the calorics lost to the hearth must be regained before good iron can be made. Take another case: A furnace carefully burdened on No. 1 iron, during a spell of damp weather, goes on to No. 2 or No. 3. Heat is lost to the furnace through absorption by the moisture, and less burden must be carried in order to get back on No. 1. When the

Jan 1, 1879

By Sylvain J. Pirson

The main value of earth magnetic measurements, outside of certain mining problems, resides in the study of deeply buried tectonic phenomena related to regional and local geology. Magnetic surveys are a necessary complement of gravimetric measurements, especially of pendulum surveys. To date, magnetometer prospecting has been used chiefly in the study of sedimentary basins where petroleum structures are associated with the uplifted basement rocks. There are, in the literature, innumerable articles dealing with such surveys as applied to oil geology but few treat of broad geological features related to regional magnetic disturbances of the earth field. An important piece of coordination work has been made by Jean Jungl for the magnetic and gravimetric measurements made in France and their geologic significance. A similar attempt at correlation of the known geology with the anomalies of the vertical component of the earth magnetic field has been made for the United States by George B. Somers2. Taking the magnetic vector as a whole, W. P. Jenny3 made a coordination of magnetism and geology for the main producing oil states of the United States. A more detailed study along the same lines is published by A. Van Weelden4 for southern Oklahoma and northern Texas; in this work magnetic and gravimetric measurements taken at stations as close as one mile apart are compiled and compared to the regional geology of the Ouachita-Amarillo uplifted area. From the literature mentioned, it is evident that reliable interpretation of magnetic' anomalies can be arrived at only when the magnetic stations are numerous and cover the area in a close net of measurements, therefore the works of Somers and Jenny, based on sparsely distributed Government measurements, can be regarded only as preliminary programs indicating lines along which further work should be done, whereas the coordination made by Van Weelden is an example of the contribution to the knowledge of regional geology that can be arrived at by the use of applied geophysics. With the hope that further systematic magnetic measurements will be carried on to solve regional and local geological problems, the author

Jan 1, 1940

By Sylvain J. Pirson

The main value of earth magnetic measurements, outside of certain mining problems, resides in the study of deeply buried tectonic phenomena related to regional and local geology. Magnetic surveys are a necessary complement of gravimetric measurements, especially of pendulum surveys. To date, magnetometer prospecting has been used chiefly in the study of sedimentary basins where petroleum structures are associated with the uplifted basement rocks. There are, in the literature, innumerable articles dealing with such surveys as applied to oil geology but few treat of broad geological features related to regional magnetic disturbances of the earth field. An important piece of coordination work has been made by Jean Jungl for the magnetic and gravimetric measurements made in France and their geologic significance. A similar attempt at correlation of the known geology with the anomalies of the vertical component of the earth magnetic field has been made for the United States by George B. Somers2. Taking the magnetic vector as a whole, W. P. Jenny3 made a coordination of magnetism and geology for the main producing oil states of the United States. A more detailed study along the same lines is published by A. Van Weelden4 for southern Oklahoma and northern Texas; in this work magnetic and gravimetric measurements taken at stations as close as one mile apart are compiled and compared to the regional geology of the Ouachita-Amarillo uplifted area. From the literature mentioned, it is evident that reliable interpretation of magnetic' anomalies can be arrived at only when the magnetic stations are numerous and cover the area in a close net of measurements, therefore the works of Somers and Jenny, based on sparsely distributed Government measurements, can be regarded only as preliminary programs indicating lines along which further work should be done, whereas the coordination made by Van Weelden is an example of the contribution to the knowledge of regional geology that can be arrived at by the use of applied geophysics. With the hope that further systematic magnetic measurements will be carried on to solve regional and local geological problems, the author

Jan 1, 1940

By H. R. Barnhurst

IT would be a difficult matter to trace from the beginning the very few improvements made in the burning of fuels prior to 1860. Doubtless the crossing of the sticks of wood in building a, wood fire early appealed to our savage ancestry as a means of expediting its effectiveness for their crude culinary purposes. Stones and andirons came later in assisting the admission of air to the under part of the fuel bed, while beacons and cressets utilized metal bars as supports for the same purpose. It is probable that Tubal Cain owed his success to the use of bellows making possible the use of mixed fuel and charge upon a hearth. With the development of working in east iron, grate bars cane in, and they are still with us doing duty in every household and almost every art where heat is a factor. Little was done beyond these crude methods prior to 1860. With the advancement of knowledge came the fuel-gas producer, a. natural child of the retorts employed in supplying illuminating gas. It is only within the last 15 years that the conclusion became general that complicated systems for saving heat would not remedy deficiencies in its primary development, and within that tine there has been great advancement in the means of producing initially fire of high efficiency, so that to clay we are moving rapidly toward loth high development and high absorption, with the resultant of high efficiencies. In studying the subject of the availability of pulverized coal as a fuel, it may occur to ask, why has this not come up earlier? This question would be naturally prompted by recalling the fact that Thomas Crompton's English patents upon his methods were issued to Min nearly 40 years ago. A conclusive answer to this, however, is that Crompton at that time had very crude facilities for raking what was at best a, very imperfect pulverization of the coal, and the expense of preparation was very great. He does not seem to have been aware of the advantage of a thorough drying of the coal in the

Jan 10, 1913

By W. A. Bruce

This paper presents the essentials of a mathematical method of studying the pressure behavior of an oil reservoir as the fluids are withdrawn. Methods are shown Whereby the behavior of a reservoir can be used to predict the future relationship between withdrawals and pressure. The oil reservoir is considered as a small part of a large porous continuum, which contains for the most part water. The expansion of this water resulting from a decrease of pressure in the oil zone causes a movement of water that is an important factor in the relationship between fluid withdrawals and reservoir pressure. Examples are given to illustrate the methods of pressure prediction for a circular reservoir containing undersaturated crude, the pressure distribution over a field that has a uniform production rate, the effect of a fault line near a field, the mutual interference of near-by fields, and the perturbing influence of a gas cap. Applications of the analysis to well-spacing problems are shown. Introduction The pressure-prediction methods to be described here are based upon the conception of an oil pool as a small part of a large porous continuum, containing for the most part water. The formation containing this water may be thought of as extending over an area of many square miles and having one or more small bodies of oil or gas trapped in high spots or reservoirs. It will be treated as having the genera1 aspect of a thin, flat sheet with an over-all tilt to the horizontal and with numerous small high spots, tight zones, and irregularities This porous continuum will be treated as being much more extensive than the oil or gas zones, but will be recognized as terminating at such large boundaries as a general fault, outcrop, unconformity, or pinch-out. Throughout the greater part of this limited porous continuum it is likely that there is a hydraulic connection. If this is true, the removal of fluid in one place will cause a disturbance that eventually will travel to all parts of the continuum. This picture has led to the recognition of water as the major fluid in the porous continuum and in many cases the expansive nature of this water as the main driving force producing the oil. The next step is the solution of the general problem of compressible liquid behavior in porous media. The works of Hurst I and Muskat2 introduced the idea of using heat-flow mathematics to consider the problem of compressible liquid flow in a porous medium. Before their reports, it had been thought sufficient to use the incompressible fluid-flow work of S1ichter.3 Law Muskat4 pointed out in detail how far the incompressible-fluirl assumption, deviated from fact even for water, of which the compressibility is about 3 X 10-6 volumes per unit volume per pound per square inch. He showed that this deviation increased with increases of distance. For example, the incompressible-fluid formula might show good agreement with the

Jan 1, 1943

By W. A. Bruce

This paper presents the essentials of a mathematical method of studying the pressure behavior of an oil reservoir as the fluids are withdrawn. Methods are shown Whereby the behavior of a reservoir can be used to predict the future relationship between withdrawals and pressure. The oil reservoir is considered as a small part of a large porous continuum, which contains for the most part water. The expansion of this water resulting from a decrease of pressure in the oil zone causes a movement of water that is an important factor in the relationship between fluid withdrawals and reservoir pressure. Examples are given to illustrate the methods of pressure prediction for a circular reservoir containing undersaturated crude, the pressure distribution over a field that has a uniform production rate, the effect of a fault line near a field, the mutual interference of near-by fields, and the perturbing influence of a gas cap. Applications of the analysis to well-spacing problems are shown. Introduction The pressure-prediction methods to be described here are based upon the conception of an oil pool as a small part of a large porous continuum, containing for the most part water. The formation containing this water may be thought of as extending over an area of many square miles and having one or more small bodies of oil or gas trapped in high spots or reservoirs. It will be treated as having the genera1 aspect of a thin, flat sheet with an over-all tilt to the horizontal and with numerous small high spots, tight zones, and irregularities This porous continuum will be treated as being much more extensive than the oil or gas zones, but will be recognized as terminating at such large boundaries as a general fault, outcrop, unconformity, or pinch-out. Throughout the greater part of this limited porous continuum it is likely that there is a hydraulic connection. If this is true, the removal of fluid in one place will cause a disturbance that eventually will travel to all parts of the continuum. This picture has led to the recognition of water as the major fluid in the porous continuum and in many cases the expansive nature of this water as the main driving force producing the oil. The next step is the solution of the general problem of compressible liquid behavior in porous media. The works of Hurst I and Muskat2 introduced the idea of using heat-flow mathematics to consider the problem of compressible liquid flow in a porous medium. Before their reports, it had been thought sufficient to use the incompressible fluid-flow work of S1ichter.3 Law Muskat4 pointed out in detail how far the incompressible-fluirl assumption, deviated from fact even for water, of which the compressibility is about 3 X 10-6 volumes per unit volume per pound per square inch. He showed that this deviation increased with increases of distance. For example, the incompressible-fluid formula might show good agreement with the

Jan 1, 1943

By D. J. Carney, R. R. Burt, E. J. Whittenberger

Hardenability (multiplying) factors for carbon, mongonese, silicon, chromium, nickel, and molybdenum have been developed for hypereutectoid low-alloy steels in which bainite is the first subcritical transformation product. These factors permit the calculation of 95, 80, and 50 pct martensite hardenability from chemical composition when steels with spheroidized structures are quenched from 1475°, 1525°, and 1575°F. The strong contributions to hardenability of the less expensive elements, silicon and manganese, suggest their use to obtain additional hardenability in hypereutectoid low-alloy steels. DURING the past decade a number of investigators'"11 have carefully developed information which permits calculation of the hardenability of medium -carbon low-alloy steels from chemical composition and grain size. These data have been especially valuable in developing less costly low-alloy steel compositions with equivalent or Improved

Jan 1, 1957

By L. H. Marshall

MALLEABLE-IRON castings frequently are made brittle by hot-dip galvanizing. The castings may be and usually are perfectly normal before the hot-dip treatment, in that they will stand a remarkable amount of distortion and punishment before fracturing, yet, after galvanizing, a single blow with a hammer will often cause a break. One such casting broke when accidentally dropped on a concrete floor. Such weakness causes galvanizers to view malleable cast iron with misgivings, and, in turn, is a source of worry to the manufacturer of the castings. It is felt, therefore, that a practical method of overcoming this embrittlement, a method that has already been used on several thousand tons of castings, will be of general interest. The purpose of this paper is to describe this immunizing process. DEVELOPMENT OF THE PROBLEM In the early days the trade was not much concerned with the finish of the castings and in most cases the only protection given to the parts placed in service was a coat of paint. It was soon found that this form of protection was inadequate and the user demanded a better type of rustproofing. In compliance with this demand, the use of zinc for coating gradually spread until it became general practice. More than half of all the zinc produced today is used for coating iron and steel, and, in spite of the recent use of cadmium and chromium, zinc coatings are still recognized as among the best general rust inhibitors for atmospheric exposure.

Jan 2, 1926

By J. E. Cannaday, R. J. Austin, R. K. Saxer

PREVIOUS investigators have determined activation energies and have postulated various controlling mechanisms for creep.'-' Recently Barrett et 01.I5 have suggested, as the result of their work with cadmium, that the apparent activation energies for creep (AHc) above 0.5 T, could be correlated by means of activation energies for self-diffusion (AHSD) and modulus of elasticity functions: AHC = AHSD - (5RT/E) dE/dT. The wide disparity of apparent activation energies previously obtained with nickel compared to those reported for other fcc metals and the desire to test the postulate of Barrett el al. prompted this study. The as-received 17.5-mil nickel wire used during this work assayed 99.87 pct pure, Table I. X-ray analysis indicated that the wire was in a stress-re- lieved state and metallographic examination revealed an equiaxed grain size of approximately 0.01 mm. Specimens degreased in acetone and cut to 1-1/2 in. lengths were tested in a cam-mechanized constant-stress creep machine. A vacuum of at least lo-5 mm Hg was maintained during all tests. Stresses were applied when thermal equilibrium was established. When a measurable (at least 0.5 pct) secondary creep was observed, the temperature was pulsed to a higher temperature. Pulsing time varied from 30 sec at 480°C to 2 min at 1300'C and above. Slopes of creep curves were determined after the initial acceleration in the strain rate had subsided and steady-state creep was achieved. To confirm the results obtained, additional tests were performed incorporating a temperature pulsing method suggested by sherby. In this method the load was removed during temperature pulsing and reapplied after thermal expansion had occurred. No appreciable differences in results were obtained. Tests were performed over a wide range of temperature (470" to 1310°C) and stresses (250 to 17,000 psi). The expression was used to calculate activation energies. In this expression T1 and T2 are the initial and final temperatures, and el and i2 are the creep rates at T, and T2. The variation of the apparent activation energies with the mean test temperature calculated by means of Eq. [I] are shown in Fig. 1. The mean test temperature (Tmean) was calculated from the relationship

Jan 1, 1967

By O. C. Ralston

The use of copper sulfate for improving the flotation behavior of sphalerite is probably at least 15 years old. The original discovery of its activating influence is somewhat obscure. The story goes that in the mill at Mascot, Tenn., its favorable action was discovered by accident, early in 1914, as follows: The original laboratory test work on a sphalerite ore gave favorable flotation results, but after a mill had been built the flotation concentration of the ore was very unsatisfactory. In diagnosing the probable reasons, one fact pointed out was that the laboratory test machine had been constructed of bronze whereas the commercial machine allowed pulp to come in contact only with wood and iron. A plate of sheet copper was hung in the flotation machine and results immediately improved. At first fanciful explanations of electrolytic and electrostatic behavior were given credence, but when the copper plate was removed and a small amount of copper sulfate substituted in the pulp an even more favorable result was obtained. Toward the end of 1914 copper sulfate was also adopted in the acid flotation circuit of the Butte and Superior Copper Co. Just who is responsible for the original discovery the present writers do not know. It seems strange that in that era of flotation litigation this discovery was not patented. While for pragmatic purposes it [nay be sufficient to know that the mere addition of copper compounds to a flotation pulp is sufficient to activate the flotation of the sphalerite, for scientific purposes it is quite desirable to know more about how the action takes place. It is the purpose of this paper to present certain evidence dealing with the mechanism of the beneficial effect. The description of the effect as activation in contradistinction to depression is now common in both the English and German languages. It makes no assumptions as to whether the zinc sulfide surfaces have been filmed with copper compounds. In fact, the principal differences of opinion expressed in the literature deal with whether there is an actual formation of CuS (or even Cu2S) on the surface of the sphalerite. Activation of sphalerite takes place in alkaline, neutral or weakly acid solutions and whereas the present day flotation of sphalerite is usually in ah alkaline solution, the early use of copper sulfate was in a sulfate solution.

Jan 1, 1930

By Louis Moyd

In the preparation of illustrations to accompany reports of investigations concerning particle shapes of various natural and manufactured materials proposed for use as he aggretates in concrete structures, it was found that stereoscopic views of such materials presented the information much more effectively than the usual two-dimensional photographs. With the whole-hearted cooperation of the Photographic Section, a technique was developed in the petro-graphic laboratory of the Concrete Research Division, U.S. Corps of Engineers, at Clinton, Miss., for simple and rapid preparation of paired stereoscopic photographs and micrographs. The method requires only equipment which is usually part of the general stock of any laboratory, and it is adaptable for all purposes in which three-dimensional views would be found superior to ordinary photographs. Stereoscopic Photographs Where the subject or subjects to be photographed are small but not of microscopic size, an ordinary camera having a ground-glass focusing screen is set up vertically over the field. The material to be photographed is placed on a card, the surface of which is suitable as a background. The card is mounted so that it can be tilted about 5' above and below the horizontal plane, on an axis that coincides with the north-south diameter of the viewing screen. A simple way of achieving this is to mount the card on an object having a convex lower surface. In our laboratory, a watch-glass has been used, with plasticene as the mounting medium. The convex surface should be mounted on a support having a round opening on top and a flat bottom. A roll of tape, a petri dish, a beaker, or any other piece of equipment having the proper shape to give stability to the setup will be satisfactory. The arrangement of the required equipment is shown in Fig 1. For the best results, the subject to be photographed should be mounted in the plane of the axis of rotation. To achieve this effect, the depth of the mass of plasticene between the background and the watch-glass is varied so that when the watch-glass is tilted back and forth on the axis, the subject to be photographed does not appear to move back and forth across the viewing screen. A permanent piece of equipment, embodying an adjustable vertical screw, with lock-nuts, could be made for this purpose. The subject may be illuminated in any manner desired. It was found that the presence of shadows intensifies the effect of depth. In taking the photographs, the concave surface is mounted so that one side of the background card is about 5' below the horizontal, while the axis remains in the horizontal plane. The subject is focused carefully on the ground glass and a picture is taken. The card is then tilted so that the opposite side is about 5' below the horizontal, while the axis still remains in the horizontal plane. The subject is again put in focus and another picture is taken. After both pictures are developed and printed, they are placed side by side in the same orientation and examined with a stereoscopic viewer. If depressions appear where there ought

Jan 1, 1950

By Grant Buma

The purpose of this paper is to present arguments and evidence that there are natural processes at work which tend to minimize the impact of solution mining on the environment. The contaminants have two sources. First are elements which were present in the roll-front deposit in insoluble compounds, for example, uranium in uraninite and coffinite, molybdenum, arsenic, iron, cobalt, nickel, etc. in sulfide minerals, vanadium in micas and clays, etc. Second are elements introduced by the leach liquor. Precipitation of reduced compounds, scavenging of heavy elements and absorption by quartz and clays, can all reduce the amount of heavy elements in solution. If a roll can be demonstrated to be actively precipitating uranium and heavy metal elements, then the presence of precipitants (pyrite and carbon) can be assumed. Criteria for recognizing an active roll are described.

Jan 1, 1979

1913. FRANK DAWBON ADAMS Montreal, Canada. 1921. WILLIAM CUTHBERT BLACKETT Sacriaton, Durham. England. 1923. GELAEIIO CAETANI Rome, Italy 1920. HENRY STURQIB DRINKER Merion Station, Pa, 1922. FEDERICO GIOLITTI Torino, Italy. 1906. SIR ROBERT A. HADFIELD London, England. 1928. JOHN HAYB HAMMOND New York, N. Y. 1921. FRANK WILLIAM HARBORD London, England. 1917. HERBERT HOOVER Washington, D. C. 1905. HENRI LECHATELIER Paris, France. 1931. WALDEMAR LINDQREN Cambridge, Mass. 1929. JOHN MARKLE New York, N. Y. 1921. C. MCDERMID London, England. 1913. EZEQUIEL ORDONEZ Mexico City, Mexico. 1909. ALEXANDRE POURCEL Paris, France. 1911. ROBERT H. RICHARDS Cambridge, Mass.

Jan 1, 1932

YEAR OF ELECTION 1913. FRANK DAWSON ADAMS, Montreal, Canada. 1921. WILLIAM CUTHBERT BLACKETT Sacriston, Durham, England. 1920. HENRY STURGIS DRINKER Merion Station, Pa. 1933. KARL EIKERS NEW YORK, N. Y. 1922. FEDERICO GIOLITTI Torino, Italy. 1906. SIR ROBERT A. HADFIELD London, England. 1928. JOHN HAYS HAMMOND New York, N. Y. 1921. FRANK WILLIAM HARBORD London, England. 1917. HERBERT HOOVER Washington, D. C. 1905. HENRI LECHATELIER Paris, France. 1931. WALDEMAR LINDGREN Cambridge, Mass. 1921. C. McDERMID London, England. 1913. EZEQUIEL ORDONEZ Mexico City, Mexico. 1911. ROBERT H. RICHARDS Cambridge, Mass. 1934. T.A. RICKARD Victoria, B.C., Canada 1933. ALBERT SAUVER Cambridge, Mass.

Jan 1, 1934

Organization Place Date 1917 Mine Inspectors Institute of U. S. A Indianapolis, Ind. July 9-11 American Society of Sanitary Engineers Grand Rapids, Mich. Aug. 1-3 National Association of Stationary Engineers... Evansville, Ind. Sept. 10-15 National Exposition of Safety and Sanitation.. New York City Sept. 10-15 American Iron, Steel & Electrical Engineers.... Philadelphia, Pa. Sept. 10-14 American Institute of Metals Boston, Mass. Sept. 24-29 American Foundrymen's Association Boston, Mass. Sept. 24-29 Chemical Industries, Third National Exhibition. New York City Sept. 24-29 American Electro-Chemical Society Pittsburgh, Pa. Oct. 3-6

Jan 7, 1917