Search Documents

By D. J. Spottiswood, C. N. Robinson, D. E. Spiller, E. G. Kelly

This paper describes the performance of a new design of spiral that is optimized for fine coal cleaning. Reduced Performance (Tromp) curves are presented to compare this spiral with the older design, as well as with other commonly used coal cleaning equipment. As an aid to equipment selection and circuit design, data are also presented to show how variables, such as flow rate, pulp density, and particle size, affect efficiency and the separation specific gravity.

Jan 1, 1985

By Wilbur C. Helt, Joseph J. Yancik

Throughout the history of mankind, the principal use of coal has been to produce heat through combustion. The heat is used in many ways: to warm air space for our comfort; to provide heat or energy to power industrial processes, such as cement and steel production; and to produce electricity. Because it is our nation's most abundant fossil energy fuel, coal in the late 20th century is on the threshold of becoming a significant source for synthetic liquids and gas energy fuels for this country. This is made possible by conversion processes which can change solid coal into various synthetic gases and liquids. These coal-derived fuels are nearly identical to the processed fuels and chemicals provided by natural gas and crude oils, which presently provide almost all the petrochemical feedstocks and energy fuels needed for the residential, light commercial, and transportation markets. A revolution is beginning to take place, not only in the United States, but in many other countries with a return to a coal-based energy economy. Also, new combustion and conversion technologies which are compatible with national health arid environmental goals are rapidly emerging. These technologies will allow coal's use to be expanded not only in its traditional markets, but also to supply markets held by natural gas and crude oil. With the worldwide decline in natural gas and crude oil reserves, coal is being looked upon to meet the energy demand. Because of these new coal conversion technologies, coal will no longer be only a combustion fuel, but a valuable raw material for production of a variety of clean fuels and chemicals. MARKETS FOR COAL: PAST AND FUTURE A simplified diagram of the marketing network for coal is shown in Fig. 1. As shown in this figure, coal is transported to its traditional

Jan 1, 1981

By W. L. Zeigler

THE tailing from the gravity concentration plant of the Hecla Mining Co., Gem, Idaho, was former-ly loaded into railroad cars to be used for ballast, highway surfacing material, or concrete work, or dis-posed of by an aerial tramway, which dumped it into another gulch. The tailing averages about 1.2 per cent lead and 0.8 oz. silver to the ton. Further treatment for the recovery of the valuable metals had been investigat-ed several times with results that did not warrant the construction of a retreatment plant; but early in 1925 experimental work was again started with small tests, and later with a 10 tons per day flotation test plant. This showed that the tailing could be ground and treat-ed by flotation at a profit. It was decided to make the new flotation plant an addition to, rather than incor-porate it in the old concentrator, the original capacity of which had been increased many times, the present arrangement being by no means ideal. The old mill buildings were of timber and board contruction, creat-ing more or less fire hazard, so all new construction was made fireproof. Construction work on the new plant was started in the middle of July, 1925, and the plant was placed in operation early in December. The building is of concrete and steel with hollow tile walls, steel sash and corrugated asbestos roofing. The ball-mill floor has for its foundation a cellular reinforced concrete block about 14 ft. deep, extending to cemented river gravel, and the cells filled with tailing to give weight to the block. Overhead, built into the steel frame, is a 5-ton hand-operated traveling crane. With both ball-mills running fully loaded, there is not the slightest trace of vibra-tion in the foundation or building. The flotation floor is of reinforced concrete beam construction and spans Canyon Creek. Adjustable plunger feeders are arranged under the the tailing-bin, which feed by gravity to a 14-in. eleva-tor, discharging to a short 18-in. conveyor. From the conveyor the tailing is discharged into a dividing hop-per, from which point the plant is arranged in three separate units. Each unit consists of a ball-mill in closed circuit with a classifier, and an 8-cell flotation machine and has an approximate capacity of 300 tons per 24 hours.

Jan 8, 1927

By Oliver B. Hopkins

Peru produced approximately 17,466,620 bbl., of oil during 1937, or slightly less than the record high of 17,593,700 bbl. established during 1936. As in 1936, the entire output of the country was derived from the La Brea-Parinas, Lobitos-Restin and Zorritos fields in the northwestern part of the country. Outside of the proven areas, drilling was 'continued by the Peruvian Government in the northern province of Tumbes on the reserved zone at Zorritos. Drilling was carried out on three locations, two of which are understood to have been abandoned during the year. In southern Peru, further attention was given by Government engineers to the Pusi and Saman districts and plans are being worked out for the commencement of drilling operations in the near future in the vicinity of Pirin. Activities in the montaiia region in eastern Peru were continued by the Compafiia Petrolera El Ganso Azul. This company acquired the interest of the Selden Breck Co., and holds some 90,000 acres along the Pachitea River a few miles above its confluence with the Ucayali. During the year, the preparation of a landing place, the cutting of a 12-km. (71/2-mile) road from the river to the drill site, and the construction of a camp were undertaken. Equipment for drilling on this company's concessions has already arrived in South America. La Brea-Parinas Estate.—Production of crude oil on the La Brea-Parinas Estate of the International Petroleum Company Limited amounted to 14,722,754 bbl. during 1937, a decrease of 403,736 bbl. from the all-time high reached during 1936. The total production from 1890 to Dec. 31,1937, was 178,390,767 bbl. During 1937, a total of 141,653 ft. was drilled, 129,516 ft. in new wells and 12,137 in deepening existing wells. In all, 57 wells were completed, 47 of which produced oil, 2 were gas wells and 8 dry. holes. Twenty-nine wells were cleaned out or deepened during the year. The average depth of new wells completed during 1937 was 2367 ft. compared with 1984 ft. for the new wells completed during 1936. There was an increased use of rotary tools during the year and this method is now used to a greater extent than the cable-tool method, which formerly predominated. Of the 57 wells completed during the year, 31 were

Jan 1, 1938

By E. T. Turkdogan, P. Grieveson

STAFF: Editor, Gerhard Derge Acting Editor, Paul G. Shewmon Carnegie lnstitute of Technology Sc hen ley Park Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: Karl L. Fetters, President; J.S. Smart, Jr., Past-President; R. C. Cole, Vice President; R. L. Hennebach, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: W. 0. Phil-brook, Chairman; H. L. Bishop, R. C. Cole, J. N. Hobstetter, W. A. Krivsky, E. R. Morgan, F. C. Langenberg, R. E. Lund, Paul Queneau, L. L. Seigle, R. L. Smith, and T. '4. Wainwright. Review and selection of manuscripts is under the supervision of the following Publications Committes: Extractive Metallurgy Division: R. E. Lund, Chatrmon; M. E. Wodsworth, Vice Chairman; D. H. Baker, Jr., G. M. Bell, R. E. Groce, W. A. Krivsky, R. A. Lewls, Charles O'Neill, A. W. Schlechten, R. E. Shinkoskey, and W. W. Stephens. Iron and Steel Division: T. V. Wainright, Choirman; H. L. Bishop, R. E. Boni, T. E. Dancy, C. W. Murphy, Johonnes M. Uys, J. B. Wagstaff, and R. G. Ward. lnstitute of Metols Division: J. N. Hobstetter, Chairman; P. A. Beck, J. J. Becker, G. F. Bolling, J. O. Brittain, J. 8. Clark, R. S. Davis, A. E. Dwight, R. W. Fountain, L. R. Girifalco, J. C. Gurland, H. S. Kclish, E. L. Harmon, J. J. Heger, A. A. Hendrickson, L. Himmel, J. P. Hirth, H. H. Johnson, Jr., R. R. Nosh, T. N. Rhodin, R. H. Richman, H. C. Rogers, W. Rostoker, C. Sherby, C. W. Spencer, L. Slifkin, J. K. Stanley, R. Steinitz, H. C. Stumpf, and R. Swolin. Published bimonthly by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc., 345 East 47th Street, New York 17. N. Y. Telephone PLaza 2-6800. Subscription $30 per year for non-AIME members in United States and North, South, and Central America; $32, foreign; $7.50 for AlME members. Single copies, $6.00, single copies foreign, $6.50. The AlME is not responsible for any statement made or opinion expressed in its publications ... Copyright 1962 by the American lnstitute of Mining, Metollurgical. and Petroleum Engineers. Inc. . . . Registered cable address, AlME New York . . . Indexed in Engineering Index, lndustriol Arts Index, and Chemical Abstracts . . . Second class postage paid at New York, N. Y., and Ann Arbor, Mich. Volume 224, Number 6.

Jan 1, 1962

By G. V. Kurdjumou

STAFF: Editor, Gerhard Derge Acting Editor, Paul G. Shewmon Carnegie Institute of Technology Schenley Park Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: Karl L. Fetters, President; J. S. Smart, Jr., Past-President; R. C. Cole, Vice President; R. L. Hennebach, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: W. 0. Phil-brook, Chairman; H. L. Bishop, R. C. Cole, J. N. Hobstetter, W. A. Krivsky, E. R. Morgan, F. C. Langenberg, R. E. Lund, Paul Queneau, L. L. Seigle, R. L. Smith, and T. V. Wainwright. Review and selection of manuscripts is under the supervision of the following Publications Committes: Extractive Metallurgy Division: R. E. Lund, Choirmon; M. E. Wodsworth, Vice Choirmon; D. H. Boker, Jr., G. M. Bell, R. E. Grace, W. A. Krivsky, R. A. Lewis, Chorles O'Neill, A. W. Schlechten, R. E. Shinko~ke~, and W. W. Stephens. Iron and Steel Division: T, V. Wainright, Choir- mon; ti. L. Bishop, R. E. Boni, T. E. Doncy, D. W. Murphy, Johonnes M. Uys, J. B. Wogstaff, ond R. G. Word. Institute of Metals Division: J. N. Hobstetter, Choirmon; P. A. Beck, J. J. Beckar, G. F. Boiling, J. O. Brittain, J. 0. Clark, R. 5. Davis, A. E. Dwight, R. W. Fountain, L. R. Girifolco, J. C. Gurlond, H. S. Kolish, E. L. Harmon, J. J. Heger, A. A. Hendrickson, L. Himmel, J. P. Hirth, H. H. Johnson, Jr., R. R. Nosh, T. N. Rhodin, R. H. Richrnon, H. C. Rogers, W. Rostoker, O. Sherby, C. W. Spencer, L. Slifkin, J. K. Stanley, R. Steinitz, H. C. Stumpf, ond R. Swolin. PuUlished bimonthly by the American lnstitute of Mining, Metallurgical, and Petroleum Engineers, Inc., 345 East 47th Street, New York 17, N. Y. Telephone PLaZa 2-6800. Subscription $30 peryear for non-AIME members in United States and North, South, and Central America; $32, foreign; $30peryear$7.50 for AIME members. Single copies, $6.00, single copies foreign, $6.50. The CentralAmerica;AlME is not responsible for any statement made or opinion expressed in its publications ... Copyright 1962 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . .Copyright.Registered cable address, AIME New York . . . Indexed in Engineering Index, Industrial Arts Index, and Chemical cableaddres .. . AlME class postage paid at New York, N. Y., and Ann Arbor, Mich. Volume 224, Number 3.

Jan 1, 1962

By David B. Scott

The Mogollon mining district, New Mexico, has received little public attention, although for 15 years it has been the leading silver producer of the state; it is situated in a region remote from the principal lines of travel, and its activities have usually been limited to the operations of two or three companies. The value of the total production of the district in the 44 years of its history has been estimated at $15,000,000. For the years 1904 to 1917, inclusive, the output was: gold, $4,370,000; silver, 10,042,000 oz.; copper, 874,862 lb.; total value, approximately $10,500,000. In 1913 the district contributed 80 per cent. of the total silver production of New Mexico, but in 1917 only 41 per cent., due to serious interruption in the operations of the leading producer. Since 1914 the silver output has diminished one-half, and the present high value of silver is nearly offset by the increase in cost of production. The output of gold has rarely exceeded 35 per cent. of the total for New Mexico. The ratio of silver to gold, by weight, has averaged 46:1 based on the whole output of the district. Location and Topography The town of Mogollon is 75 mi. (121 km.) by a poorly located highway ,. from the nearest railroad terminals, at Silver City and Tyrone. All supplies are transported by motor trucks and teams. The area, sometimes called the Cooney Mining District, lies on the western flank of the Mogollon Mountains, which occupy the western part of Socorro County. The elevations drop steeply on the west to the valley of the San Francisco River, adjacent to the Arizona boundary. The topography is very rugged, the whole area being sharply dissected; deep canyons with steep gradients and rugged walls are characteristic of the whole western slope of the Mogollon Range. The main canyons i run east and west, and usually maintain a flow of water during the entire year. As would be expected in a region of such deep dissection, the mines are generally dry. The mountain ridges between the canyons have altitudes varying from 7000 to 10,000 ft. (2130 to 3050 m.) and drop sharply, on their western face, to the floor of the San Francisco Valley at an elevation of 5000 ft. (1525 m.). Erosion has been rapid, and the

Jan 1, 1920

By Morris Cohen

STAFF: Editor, Gerhard Derge Acting Editor, Paul G. Shewmon Carnegie Institute of Technology Schenley Park Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: Karl L. Fetters, President; J.S. Smart, Jr., Past-President; R. C. Cole, Vice President; R. L. Hennebach, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: W. O. Phil-brook, Chairman; H. L. Bishop, R. C. Cole, J. N. Hobstetter, W. A. Krivsky, E. R. Morgan, F. C. Langenberg, R. E. Lund, Paul Queneau, L. L. Seigle, R. L. Smith, and T. V. Wainwright. Review and selection of manuscripts is under the supervision of the following Publicotions Committes: Extractive Metallurgy Division: R. E. Lund, Chairman; M. E. Wadsworth, Vice Chairman; D. H. Baker, Jr., G. M. Bell, R. E. Grace, W. A. Krivsky, R. A. Lewis, Charles O'Neill, A. W. Schlechten, R. E. Shinkoskey, and W. W. Stephens. Iran and Steel Division: T. V. Wainright, Choirman; H. L. Bishop, R. E. Boni, T. E. Dancy, D. W. Murphy, Johannes M. Uys, J. B. Wogstoff, and R. G. Ward. Institute of Metals Division: J. N. Hobstetter, Chairman; P. A. Beck, J. J. Becker, G. F. Bolling, J. 0. Brittain, J. B. Clark, R. S. Davis, A. E. Dwight, R. W. Fountain, L. R. Girifolco, J. C. Gurland, H. S. Kalish, E. L. Harmon, J. J. Heger, A. A. Hendrickson, L. Himmel, J. P. Hirth, H. H. Johnson, Jr., R. R. Nosh, T. N. Rhodin, R. H. Richman, H. C. Rogers, W. Rostoker, C. Sherby, C. W. Spencer, L. Slifkin, J. K. Stanley, R. Steinitz, H. C. Stumpf, and R. Swalin. Published bimonthly by the Americon Institute of Mining, Metallurgicol, and Petroleum Engineers, Inc., 345 East 47th Street, New York 17, N. Y. Telephone PLaza 2-6800. Subscription $30 peryear for non-AIME members in United States and North, South, and Centrol America; $32, foreign; $30per$7.50 for AlME members. Single copies, $6.00, single copies foreign, $6.50. The AlME is not responsible for any stotement made or opinion expressed in its publications ... Copyright 1962 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address, AlME New York . . . Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts . . . Second class postage paid at New York, N. Y., and Ann Arbor, Mich. Volume 224, Number 4.

Jan 1, 1962

By Francis Foley

Small cracks in a plane normal to the axis of steels are found to be prevalent around the water hole of drill steels that have been in service for an unknown period of time. Cracks are not found on the exterior surface of the steels nor to any noteworthy extent even in the water holes of new drill steels. Undulations and serrations are found in the surface of the water hole in new steels; it is in the bottom of such defects that cracks appear to develop in used steels. The occurrence of the more serious of these cracks at the point in the steel to which it has been heated for forging or hardening is thought to account to a great extent for failures in that region. DURING the past, year, we have investigated the cause of 88 per cent, of the failures by breakage near the bit end of some 1-in. hollow, hexagon, drill steel used in a metal mine. This breakage in the region of the bit end of the steel was peculiarly interesting because we have been led to believe that breakage is most prevalent at the shank end of drill steels near the place where the steel is gripped in the chuck of the machine. Records from the mine showed, also, that the breakage was much more frequent in the short lengths of large gage than in the longer steels; this is shown graphically in Fig. 1. Because the shorter lengths of steels are usually those that have been made from broken pieces of long steels or from steels that have worn down in service, rarely being made from new stock, those who are wont to suspect steel of tiring and crystallizing in its old age through fatigue are quite apt to see in this instance an argument in favor of their idea. As usual, a careful examination of these steels reveals defects of a character hardly to be overlooked in favor of such a cause. The steel in question was rolled with a sand core and was of the usual drill steel composition: Carbon 0.85 per cent., manganese 0.60 per cent., silicon 0.25 per cent., phosphorus 0.02 per cent., and sulfur 0.02 per cent., with the exception that in some specimens there was vanadium, not exceeding 0.20 per cent.

Jan 3, 1924

By William Benzon

Bethlehem Steel's Cambria Division coal cleaning and preparation plant, operated by Bethlehem Mines Corp., is located in Cambria County, Pa., about 2 ½ miles southeast of Ebensburg. Here, above ground, is the most modern coal preparation plant in the world. Below the surface is a new coal mine also referred to as "the most modern that could be built today." The preparation plant has a capacity of 1370 tons of clean coal per hr. It serves three Bethlehem mines, Heisley No. 31, Revloc No. 32, and the new Cambria Slope No. 33.

Jan 12, 1965

By D. Jeulin

For iron ore sinters to be good blast furnace burden, they need to possess certain basic properties such as cold mechanical strength, reducibility, etc. Relations between such basic parameters and sintering parameters (composition of the mix, fuel consumption, operating conditions of the sintering plant, etc.) are not always well understood. For example, one cannot explain the differences in quality noticed for sinters having the same chemical composition. In this paper a new approach is proposed for the characterization of iron ore sinters by a quantitative description of their morphology. The Texture Analyzer LEITZ T.A.S. is used for this purpose and such morphological parameters as sizes of microstructures and the size distribution of phases are measured on samples of sinters. The results indicate that these measurements can be correlated with the sinter quality.

Jan 1, 1977

By R. E. Lamborn

A summary of oil and gas development in Ohio for 1935 must necessarily be brief. As attention of the state government to the oil and gas industry has never included the collection and compilation of statistics on production, either by producing sands, by counties, by fields, or for the state as a whole, such information as requested in Table 1 of this symposium is impossible to secure for this state. In the absence of production data chief attention must be directed to drilling activity for the year. Information such as can be compiled from various sources, including weekly drilling reports to operating companies and trade journals, is given in the following paragraphs with the realization that the data may not be complete in all its details. Drilling Activity by Fields Drilling activity during 1935 was similar to the preceding year in , that the major operating companies were generally content to drill lease-requirement and offset wells and in that comparatively little effort was made to discover new pools. A compilation of completions recorded in weekly reports to drilling companies and in trade journals show 1022 tests completed for the year in 53 counties of the state. Of this total number, 653 wells were commercial producers and 369 were classed as dry holes. Production was secured in 40 counties from formations ranging in depth to 5700 ft. and ranging in age from Middle Ordovician to upper Pennsyl-vanian. From the standpoint of new production for the year, the most important sands are the Clinton of Silurian age, the Berea of Mississippian age and the Shallow sands of Mississippian above the Berea and of Pennsylvanian age. Trenton Sand Field Production in the field of Trenton sand, which originally included parts of 15 counties in northwestern Ohio, is now on the decline. Seventy-three completions were reported in this field during 1935, of which 33.8 per cent were dry holes. Activity centered in Allen County with 12 completions, two of which were dry holes; in Hardin County with 11 producers; and in Wyandot County with 12 producers and 2 dry holes.

Jan 1, 1936

By R. E. Lamborn

A summary of oil and gas development in Ohio for 1935 must necessarily be brief. As attention of the state government to the oil and gas industry has never included the collection and compilation of statistics on production, either by producing sands, by counties, by fields, or for the state as a whole, such information as requested in Table 1 of this symposium is impossible to secure for this state. In the absence of production data chief attention must be directed to drilling activity for the year. Information such as can be compiled from various sources, including weekly drilling reports to operating companies and trade journals, is given in the following paragraphs with the realization that the data may not be complete in all its details. Drilling Activity by Fields Drilling activity during 1935 was similar to the preceding year in , that the major operating companies were generally content to drill lease-requirement and offset wells and in that comparatively little effort was made to discover new pools. A compilation of completions recorded in weekly reports to drilling companies and in trade journals show 1022 tests completed for the year in 53 counties of the state. Of this total number, 653 wells were commercial producers and 369 were classed as dry holes. Production was secured in 40 counties from formations ranging in depth to 5700 ft. and ranging in age from Middle Ordovician to upper Pennsyl-vanian. From the standpoint of new production for the year, the most important sands are the Clinton of Silurian age, the Berea of Mississippian age and the Shallow sands of Mississippian above the Berea and of Pennsylvanian age. Trenton Sand Field Production in the field of Trenton sand, which originally included parts of 15 counties in northwestern Ohio, is now on the decline. Seventy-three completions were reported in this field during 1935, of which 33.8 per cent were dry holes. Activity centered in Allen County with 12 completions, two of which were dry holes; in Hardin County with 11 producers; and in Wyandot County with 12 producers and 2 dry holes.

Jan 1, 1936

By R. S. McClellan

In order to meet the ever-increasing demand by consumers for uniformity of ground talc, a new method of blending its finished product has been developed by Gouverneur Talc Company, Inc., at its plant near Gouverneur, N. Y. The method has been in use for a sufficient length of time to be now judged a success. The Gouverneur district is the leading talc producing area of the world, inasmuch as more tonnage is produced there than from any other state in the U.S. or, so far as is known, from any other locality in the world. Almost all of the output goes into industrial uses, with ceramics and paint being the principal consuming industries. The physical and chemical specifications imposed by these industries are stringent and the trend, as in most industries, is toward ever increasing severity. The blending method described herein has aided Gouverneur Talc to keep up with this trend.

Jan 3, 1961

By Dewitt T. Ring

Reliable and detailed data covering the enormous number of wells drilled and the long historical production of the state, many of which were never recorded until recent years, render it impossible to gather statistical material suitable for the Institute's standardized form. The total production of crude oil in Ohio for the year was 3,654,503 bbl., which is less than the total production in the United States for the peak day of August 1937. For a period of eight years, from 1895 to 1902 inclusive, Ohio produced more oil than any other state. During the year, 1271 tests were drilled in the state, or 114 more than in 1936. Of these, 317 were oil wells, with an initial production of 7088 bbl., an average of 22.3 bbl. per well; 503 were gas wells, with an initial open flow of approximately 222,441 M cu. ft., or 443 M cu. ft. per gas well drilled; 451 were dry holes, that is, 35 per cent of the total completions. A number of factors account for the steady decline of oil production in Ohio. In the state, at the close of thc year, there were fewer than 28,122 producing oil wells. In 1936, there were 30,150 operated oil wells with an average yearly production per well of 126 bbl. The production for 1937 averaged 130 bbl. per well. During the year, 2028 oil wells were abandoned. In other words, old wells are being abandoned more than six times faster than new ones are being drilled. Since the inception of the oil and gas industry in Ohio, between 150,000 and 160,000 wells have been drilled in the state; new potential territory, offering desirable locations for either oil or gas, is becoming increasingly more difficult to find; the dry-hole percentage will continue to increase. Prices Another factor directly affecting the crude situation during the year was the matter of price and proration of Pennsylvania grade oil. The posted price for Pennsylvania grade in Ohio on June 7 was $2.37 per barrel; at the close of the year, it was $1.70 per barrel, or a reduction of 28 per cent in price. In addition to this price cut, a 50 per cent pro-

Jan 1, 1938

By D. E. Hyatt

Many flotation plants practicing pyrite depression, mills leaching gold and silver ores, blast furnace facilities, and many metal plating shops share at least one common waste-water constituent of particular environmental concern-cyanide. In free or complexed form, cyanide ion is an emotionally and technically problematical reagent whose removal from water deserves attention. The initial consideration of the fundamental nature of soluble cyanides is followed by a discussion of decomposition or removal options for simple cyanide species. Complexed cyanide reactivity is discussed as it relates to ongoing or proposed methods for the decomposition or removal of soluble cyanides. New approaches to cyanide removal are discussed.

Jan 1, 1977

By Thomas Fraser, Robert MacLachlan

The dry cleaning of coal is a relatively new art and, as might have been expected, a number of unforeseen problems have been brought to light in the few years that dry methods of treatment have been in commercial use. The pneumatic concentrators that were first adapted to the cleaning of coal had already been developed to a fair degree of efficiency, although at low ratings, in the field of ore dressing. The concentrating machines, therefore, were in a relatively more perfected state than the general technology of dry cleaning and, for this reason, the major difficulties encountered in the early plants were in the accessory operations involved in the servicing of the cleaners rather than in the functioning of the cleaners themselves. The crudities of a new technology were further aggravated, in some cases, by meagerness of appropriations which precluded even the provision of adequate storage bins and such other facilities as had been long recognized as indispensable to the proper functioning of older types of cleaning plants. The practice of dry cleaning is now sufficiently established so that we may examine critically auxiliary equipment and operations. The cleaning processes have been so simplified, with respect to presizing of the raw coal required and the quantity of air circulated, that stinting of expenditures for auxiliary equipment is not necessary to keep the per ton cost of installation in line with complete and well designed plants of other types. Furthermore, sufficient operating experience has been accumulated to ascertain the conditions most conducive to effective operation of dry-cleaning machines; at least the essentials of a definite technology of dry cleaning has been established. Early Operating Problems The problems that have occupied the builders and operators of dry-cleaning plants from the beginning have been relatively few, but difficult of solution. The principal difficulties have been: 1. The proper sizing of the raw coal to suit the cleaning process. 2. The handling of raw coal when it is delivered wet from the mine. 3. Dust collecting. 4. The maintenance of uniformity in cleaning performance.

Jan 1, 1931

By J. P. Nielsen

When two grains in a polycrystalline specimen meet at a point in the course of grain-boundary movements, and the new boundary created at the point is one of relatively low specific free energy, a nonequilibrium boundary condition occurs. The nonequilibrium is enhanced if the other grain boundaries involved at the point of meeting are relatively high in specific free energy. The nonequilibrium results in a correction by growth of the complex grain (two subgrains) to a large size, sufficient in many cases for it to become a self-propagating unit, i.e., a recrystallization grain. This mechanism, herein called "geometrical coalescence," is proposed as a logical origin for recrystallization nuclei, particularly for secondary recrystallization. RECENT publications1-' indicate that considerable progress has been made toward a complete understanding of the three microstructural processes in metals: recovery, recrystallization, and grain growth. However, a major problem persists, namely, the origin of recrystallization nuclei. It is generally accepted that once a recrystallization nucleus, a secondary recrystallization nucleus particularly, has reached a certain size, it will continue to grow at the expense of its neighbors, simply as a consequence of grain-boundary free-energy considerations. What has remained obscure, however, is the mechanism whereby such a nucleus comes into being and grows to the self-propagating size. Recrystallization Nucleation in a Two-Dimensional Grain-Boundary System In the left portion of Fig. 1 is shown schematically the meeting of grains 1 and 4 on disappearance of boundary 2-3, i.e., the boundary that existed between grains 2 and 3, as might happen in the course of normal grain-boundary migration. If, by chance —and the probability is not necessarily small— grains 1 and 4 are close together in their mutual orientations, or in some other special way mutually oriented so that the new common boundary has relatively a very low specific free energy (hereinafter referred to by s), then the grain boundary arrangement as depicted in the figure is highly unstable. This is particularly so if boundaries 1-3, 3-4, 4-2, and 2-1 are high in their s values. Assuming, for the sake of argument, that boundary 1-4 has a s equal to zero, and the s's of all the other boundaries present are equal to each other and constant, then the boundary arrangement on the right in Fig. 1 will be

Jan 1, 1955

By T. Egleston

THE direct process for the manufacture of iron which is principally used in the United States, in New York and New Jersey, is called the Jersey forge, the Champlain forge, the Catalan forge, the Bloomary forge or fire, and sometimes a Forge fire. Dr. T. Sterry Hunt, who has discussed the process as applied to the beach sands of Canada as well as to ores, in the Report of the Canadian Geological Survey for 1867-69, has shown that the name of Catalan forge is incorrect, as this process in no way resembles the Catalan, but is really the old German bloomary modified by long use in this country. Dr. Hunt gives the probable history of the introduction of the process into the United States, and a series of historic citations of great interest relating to it. Not¬withstanding the improvements which have been made in the construction of the furnace and its greater output, the process to-day, in all its essential features, is carried out as Karsten described it. It should now be known as the American Bloomary. The name of Jersey or Champlain forge or fire is not sufficiently distinctive. The name of Bloomary, by which the process is usually distinguished, is objectionable, not because it is incorrect but because it is indefinite, as the Knobbling fires, which are a very slight modification of the Walloon process, for making blooms either from pig iron or by sinking scrap, are also called Bloomaries, and although Knobbling fires are only used in a few localities where charcoal pig is made, and special grades of charcoal-refined blooms are required, one does not, without an explanation, know whether the blooms are being manufactured from ore or pig. The name Forge fire is equally indefinite, as it might just as well apply to any of the five direct methods of making blooms which have been in use in Europe, but which have now mostly gone out of date. The Dame of American Bloomary, however, is the one which most completely describes it, and is the one least open to objection. The names of German, Jersey, and Champlain bloomary are too local, and these adjectives are thought unnecessary by those who use the process, and we shall not therefore describe it under any of these names, but as the American Bloomary process. * Read at the Montreal meeting, September, 1879.

Jan 1, 1880

By John Tyssowski

In 1925, Harry Howard Stout, then metallurgist for Phelps Dodge Corporation, while investigating the cleaning of cathode copper by various gases at elevated temperatures below the melting point of the metal, observed in the laboratory that particles of pure copper heated in a closed tube filled with hydrogen seemingly "stuck together." By further investigation he found that there was actual crystal growth across the boundaries of the particles of pure metal; in other words, there was a complete new crystal realignment and growth throughout the newly formed copper mass. It was coalescence, not adhesion; the several particles had become one unit. From this discovery has been developed the coalescence process, whereby copper of cathode purity is squirted out in semifabricated form from an extrusion press, by the application of about 3000 tons pressure on a 10-in. piston. Stout decided that cathode copper produced by electrolytic deposition was the logical source of the pure copper required for the coalescence process, but as there was no way of reducing the ordinary tough commercial cathodes to the small particles required he was confronted by a serious problem at the outset. Under his direction, this problem was solved by William H. Osborn and Harry Howard Stout, Jr. They developed the process and technique for producing cathode copper in brittle, friable form, and to them must be given the greater part of the credit for this phase of the development program as well as for that relating to the gas cleaning of the cathode particles. Concurrently, the three metallurgists worked on the problem of effecting a complete union of the cathode particles. Adequate washing was all that was needed to free the particles from electrolyte solution and slimes. A press was designed to produce briquettes of the proper porosity and density, and a method was devised of removing surface oxidation from the particles of cathode, by treatment in an atmosphere of deoxidizing gas at an elevated temperature. The temperature was determined at which the surface cleansing and preheating could be done in one operation, and for this a charging and preheating furnace in which there is maintained a positive pressure of deoxidizing gas atmosphere was designed. And finally, a method of feeding the heated briquettes of deoxidized cathode copper into an extrusion press without contamination from the air was evolved. For the final stage, a press was required because not only heat but pressure was required to obtain complete growth of the new crystals between the cathode particles as well as the elimination of all voids or non-coalesced areas. All essential stages of the process are protected by patents or patent applications in the United States and principal foreign countries, and the copper is produced on a commercial scale.

Jan 1, 1941