Search Documents

By Charles H. Jones

Jan 1, 1905

By Klaus Schwerdtfeger

The equilibria in the Cr-N system have been investigated in the temperature range 1100° to 1310°C by reacting chromium powder with Nz-Hz gas mixtures. The solubility of nitrogen in chromium in equilibrium with chromium subsitvide ("Cr,N") is given by Chromium subnitride is nonstoichiotnetric; its nitrogen content is always less than that corresponding to the formula CrzN. The lattice paranzeters of quenched samples have been measured; c, and a. parameters are found to increase with increasing nitrogen content. The growth rate of the subnitride layer on chromium plates was measured by a thermogravimetric technique, using a silica spring balance. The self-diffu-sivity obtained from the theoretical analysis of the parabolic rate constant is found to decrease with increasing nitrogen content, i.e., with decreasing vacancy concentration in the nitrogen sublattice. The intrinsic nitrogen diffuivity is derived from another series of rate measurements using "CrzN" plates; the intrinsic diffusivity, DN = 3.2 X 10-a cmZ sec-' at 1200 C, is found to be essentially independent of- the subnitride composition. The concentration gradient was measured in a chromium subnitride layer by the X-ray method and found to be consistent with the derived diffusivity value. TWO chromium nitrides are known to exist:' the nonstoichiometric subnitride "CrzN" and the nitride CrN. In the present work the kinetics of the formation of chromium subnitride from chromium and nitrogen have been investigated at 1100" and 1200°C. In additional experiments the relevant equilibria have been measured. The data are used to evaluate the diffusivity of nitrogen in chromium subnitride. Since chromium nitrides are often found in chromium-containing steels, the results are expected to be helpful in the interpretation of the chemical reactions between chromium steels and nitrogen. Equilibria in the Cr-N system have been determined by several investigators.2"3 The rate of nitriding of chromium was measured by Arkharov et a1 .' in ammonia in the temperature range 800" to 1200°C. The parabolic rate law was observed. Due to the undefined nitrogen activity of the ammonia atmosphere, it is dif- ficult to interpret these rate data theoretically. An additional difficulty arises from the fact that the two-layer scale consisting of CrN and "Cr2N" was formed at the temperatures below 1030°C. The rate of nitriding of technical chromium (95 pct) was measured by Zaks in nitrogen at -1 atm in the temperature range 800" to 1300°C. EXPERIMENTAL METHODS The chromium samples were reacted with Nz-HZ gas mixtures in a vertical tube furnace, wound with Pt-10 pct Rh resistance wire. The gas-tight reaction tube was of high-purity recrystallized alumina. In nitrogen solubility measurements the nitrogen content of chromium was determined by the Kjeldahl method, on samples quenched in the cold part of the furnace. The nonstoichiometry of the subnitride and the nitriding rates were measured thermogravimetrically using a sensitive (+0.1 mg) silica spring balance. For the equilibrium measurements samples of 1 g of chromium powder contained in high-purity alumina crucibles were used. In order to remove most of the oxygen and nitrogen impurities from the chromium, the samples were initially annealed in purified hydrogen until a constant weight was obtained. The chromium plates (approximate dimensions 2 by 1 by 0.08 cm) used for the rate measurements were machined from ingots obtained by arc-melting of iodine-processed chromium. According to manufacturers' specifications the purity of the chromium powder was 99.9 pct Cr and that of the iodine-processed chromium 99.99 pct Cr. Our own spectroscopic analysis of the chromium powder yielded 0.02 pct Fe, 0.05 pct Mn, 0.05 pct Si, and 0.02 pct Ti as major impurities with all the other detectable elements below 0.005 pct. The nitrogen partial pressure of the gas phase was controlled by mixing prepurified hydrogen and nitrogen with constant pressure head capillary flowmeters. Oxygen and water vapor were removed from the mixed gas by passing it through columns of platinized asbestos (450°C) and anhydrone. The gas flowed upward in the furnace with flow rates of 300 to 500 cu cm per min (25"~). Gas tightness of the furnace system was ensured by pressure checks at regular intervals. The furnace temperature was controlled electronically in the usual manner. The reported temperatures were measured with a Pt/Pt-10 pct Rh thermocouple and are estimated to be accurate within ±$C The X-ray measurements were made with a Debye-Scherrer camera and a diffractometer using chromium radiation {\Ka = 2.29092A). EQUILIBRIUM MEASUREMENTS The experimental results of the equilibrium measurements are contained in Tables I to In. Fig. 1 shows the solubility of nitrogen in solid chromium in the temperature range 1100" to 1310°C. In Figs.

Jan 1, 1968

THE New York Petroleum Club has elected the following officers for the current year: Chairman, William B. Heroy; vice-chairmen, Edwin B. Hopkins, Warren. A. Sinsheimer; secretary, A. C. Hunter. This is the local section of the Petroleum Division. It holds monthly lunch-eons, usually in the rooms of the Railway Club.

Jan 3, 1927

By Rossiter W. Raymond

The term " pipe-vein " has recently been applied in this country to certain deposits of lead ore in magnesian limestone. The use of the term has been twofold. It has been revived as a term found in textbooks on mineral veins, with the implied or declared assertion that the ore-deposits thus named in this country are similar to those which have borne the title abroad. It has also been advanced as an appropriate name for a new class of deposits, even if such a class had not previously been recognized. In either case, the assumption is that pipe-veins form a group or class by themselves, and are not merely interior and subordinate features in larger deposits. The peculiar mining law of the United States, which regards " the vein," whatever that may be, as the basis of title, lends a special interest to these claims. But the object of this paper is rather to discuss the subject from the standpoint of geology and technical literature. I shall briefly answer two questions: (1) What are pipe-veins as described in technical literature? and (2) Is the name appropriate or necessary for a new class of deposits ? The term " pipe-ore," as applied, for instance, to irregular, cylin-

Jan 1, 1879

By Rossiter W. Raymond

(Read at the Amenia Meeting, October, 1877.) THE term "pipe-vein" has recently been applied in this country to certain deposits of lead ore in magnesian limestone. The use of the term has been twofold. It has been revived as a term found in textbooks on mineral veins, with the implied or declared assertion that the ore-deposits thus named in this country are similar to those which have borne the title abroad. It has also been advanced as an appropriate name for a new class of deposits, even if such a class had not previously been recognized. In either case, the assumption is that pipe-veins form a group or class by themselves, and are not merely interior and subordinate features in larger deposits. The peculiar mining law of the United States, which regards " the vein," whatever that may be, as the basis of title, lends a special interest to these claims. But the object of this paper is rather to discuss the subject from the standpoint of geology and technical literature. I shall briefly answer two questions : (1) What are pipe-veins as described in technical literature? and (2) Is the name appropriate or necessary for a new class of deposits ? The term "pipe-ore," as applied, for instance, to irregular, cylin-

Jan 1, 1878

By T. L. Joseph

IN connection with its investigations of the blast'-furnace process, the Bureau of Mines, in coöperation with the Minnesota School of Mines Experiment Station, developed a 6-ton experimental furnace. Such a furnace was needed to determine the feasibility of producing ferromanganese from Minnesota manganiferous iron ores, a problem of national importance because of the present need for manganese in the steel industry and our small reserves of ferro-grade ores. Furnace operators are reluctant to use new or untried raw materials or to make decided innovations in practice on account of the financial hazard of experimenting with full-scale equipment. A small furnace which can be operated at a relatively low cost is particularly adapted for testing new, raw materials and for determining the feasibility of decided innovations in practice. Laboratory experiments, plus whatever information may be available, are valuable but often do not indicate the net result of changes in an operation involving a large number of interrelated variables. From time to time the coöperation of the Bureau of Mines is solicited in connection with problems involving departures from normal procedure. Under these circumstances some sort of a practical demonstration is a desirable forerunner to full-scale operations which appear feasible after small-scale tests.

Jan 1, 1928

By Philip McKenna

WHEN a new material becomes available to industry, it is useful to describe its properties as a guide to its most effective application; and when the new material may be produced in compositions having a series of graded properties, tests to select the combination of properties best adapted for various uses are helpful. The class of materials to be con-sidered in this paper are hard tool materials produced by processes of powder metallurgy from hard carbide constituents and various matrices of iron, nickel or cobalt, or alloys of them with tungsten, or tungsten and carbon. The customary use of carbide hard alloys is for metal-cutting tools; although wire-drawing dies, lathe centers, follow rests, grinding rests, burnishers, rolls, extrusion dies, measuring gauges and micrometers, and a number of other tools are also made with these hard alloys as the essen-tial wear-resisting parts. The properties and tests to be considered are those affecting these uses. In the development of tool, materials since the industrial revolution we have had carbon tool steels, Mushet steel, high-speed steels, stellites, and now cemented carbide compositions. For an understanding of the latter category of materials their properties and uses relative to the older and more familiar tool materials will be considered.

Jan 1, 1938

By T. A. Read, S. W. Kitchen, H. I. Fusfeld

At the present time most artillery cartridge cases are used only a single time. Since the process of reshaping a fired cartridge case so that it may be used again is much simpler and cheaper than the original manufacture of the case, it is clear that important savings could be effected if such re-formed cases were used in place of new cases. Extensive use of reconditioned cases has been hindered in the past, however, by the deterioration of the brass which may occur in the period of time between the first firing and the reconditioning of the cartridge cases. This deterioration sometimes results in a dangerously high incidence of firing splits in groups of reconditioned cartridge cases. It appears that the mechanism of the deterioration is the season cracking of the brass, for season cracks, of varying degrees of severity, may frequently be found in the cartridge cases after their return from the field. There are, of course, severe practical limitations to the extent to which fired cartridge cases can be protected from corrosion under battle conditions, particularly since the powder residue in the case is itself corrosive. The present paper describes a rapid method of testing the sidewalls of artillery cartridge cases for the presence of season cracks. This method has been developed specifically for use in connection with the reconditioning of fired cases, and makes it possible to carry out 100 per cent inspection. This new method of inspecting cartridge

Jan 1, 1945

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburg, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3

Jan 1, 1923

By Cyril Stanley Smith

IsolatEd alloys of copper and silicon were prepared and examined by chemical methods more than one hundred years ago, but it was not until the work of Rudolfi l that the equilibrium relations were studied. The early history of the alloys was well described by Baradue-Muller 2 and need not be further discussed here. The diagram of Rudolfi, based entirely on thermal observations, showed sillcon to be soluble in copper up to 4.5 per cent. at 849" C., at which temperature there was a peritectic horizontal resulting from the formation of a ß phase with about 7.4 per cent. silicon from a and liquid with 7.85 per cent. silicon. The ß phase was believed to form a eutectic with Cu3Si at 820" C. and 9.8 per

Jan 1, 1929

By Cyril Stanley Smith

IsolatEd alloys of copper and silicon were prepared and examined by chemical methods more than one hundred years ago, but it was not until the work of Rudolfi l that the equilibrium relations were studied. The early history of the alloys was well described by Baradue-Muller 2 and need not be further discussed here. The diagram of Rudolfi, based entirely on thermal observations, showed sillcon to be soluble in copper up to 4.5 per cent. at 849" C., at which temperature there was a peritectic horizontal resulting from the formation of a ß phase with about 7.4 per cent. silicon from a and liquid with 7.85 per cent. silicon. The ß phase was believed to form a eutectic with Cu3Si at 820" C. and 9.8 per

Jan 1, 1929

ASHBEL WELCH, LAMBERTVILLE, N. J.: Dr. Dudley has given the wear of steel rails under four different conditions. He arrives at the conclusion that the softer rails, or those that from their composition ought to be softer, wear better than the harder. But there is another condition which has an important bearing on the subject, and, should not be overlooked,-the weight on a wheel. With the lighter weights of the past, the softer rails may have worn best; with the heavier weights of the future, the harder may wear best. Weights will probably be increased up to the capacity of steel to bear; then doubtless the harder steel will wear best. A leaden rail with ten pounds on a wheel might carry millions of tons, but with one hundred pounds on a wheel, it would be destroyed by a few thousand tons. So in the days of iron rails, my experience was that the softer rails under light machinery stood better than some of the harder; but under heavy machinery the softer were much the most rapidly destroyed. His doubtless the same with steel. The pounding motion of the wheels loosens or spreads the particles of a thin film of steel; the pull lengthwise on the rail de- * Metallurgical Review, vol. i, page 1. † The remarks as here given, as in the previous discussion on steel rails, have all been written out or revised by the participants in the discussion, and represent, therefore, their mature views. It has been thought that this plan, when it can be carried out without doing any of the speakers injustice in debate, is much to be preferred to a strictly verbatim report. The remarks of Mr. Chanute were sent to the secretary after the. meeting, and although they did not form a part of the actual discussion, there can be no doubt of the desirability of including them in this report. The papers under discussion were “Rail Specifications and Rail Inspection in Europe,” by C. P. Sandberg ; " The Wearing Capacity of Steel Rails in Relation to the Chemical Composition and Physical Properties," by C. B. Dudley, and a Rail Patterns," by A. L. Holley. T. M. D., Secretary.

Jan 1, 1881

By A. Vifian, I. lwasaki

Several samples of copper-nickel ore from the Duluth Gabbro were studied to relate their mineral-ogical characteristics with their amenability to concentration by flotation. The most common rocks in the samples were norites, gabbros, and troctolites. The texture of the rocks varied from coarse pegma-titic to very fine. The copper contents ranged from 0.2-0.7% and the nickel contents from 0.07-0.15%. The ore minerals were chalcopyrite, cubanite, pyrrhotite, and pentlandite. Most of the ore minerals occurred in interstices between laths of plagioclase, but some were included in the gangue grains. The samples responded readily to xanthate flotation. After a 65 to 100-mesh grind about 95% of the copper and 85% of the nickel were recovered in a bulk sulfide concentrate. Such recoveries remained constant even with grinds as fine as 270 mesh due to the extremely fine inclusions of sulfides in the silicate gangue. A finer grind than 270 mesh was necessary to free the copper-iron sulfides from the nickel-iron sulfides. A combination of time and British gum* was quite effective in producing concentrates analyzing 25-30% copper. The nickel concentrate averaged 1.5% nickel. Most of the nickel lost in the tailing was present as un-liberated sulfides and not as nickel in the olivine structure. The nickel content of the olivine was only about 0.05 or 0.08%. Western world nickel usage in 1967 is expected to be the second highest on record, amounting to 825 million lb. Despite a rise in mine production, however, demand is expected to exceed supply in 1968. ' Hence, exploration, development, and production expansion projects are being accelerated on a world scale. In Minnesota the copper-nickel bearing Duluth Gabbro is receiving much attention. During the past year 11 companies have been granted leases in the region, and the 1967 Minnesota legislature enacted a tax law designed to encourage the development of a copper-nickel industry. Although it is only during the past few years that mining companies have shown an active interest in the Minnesota copper-nickel deposit, copper-nickel minerals have been known to exist in northeastern Minnesota since 1899.3 At the 28th Mining Symposium, Dr. P. K. Sims, from the Geological Survey of Minnesota, gave a review of copper-nickel exploration in northeastern Minnesota,4 in which he emphasized that the potential of the Duluth Gabbro complex is large. Tests on samples from the Kawishiwi River area were reported by the United States Bureau of Mines in 1955.' In 1964, the Mines Experiment Station described tests on samples from the Gunflint Trail: and in 1966 the Minnesota Geological Survey published a geological map of the Gabbro Lake Quadrangle. The Mines Experiment Station published a study of the concentration of a Minnesota copper-nickel ore in 1967.7 The present paper is divided into three parts. The first describes the mineralogy of some rock samples from the Kawishiwi River area of northeastern Minnesota; the second summarizes the results of numerous flotation tests that were made on the samples, and the third explains the loss of nickel in the flotation tailing. MINERALOGY OF KAWlSHlWl ROCKS Recently five samples of mineralized gabbro from the Kawishiwi River area, a few miles east of Ely, were received at the Mines Experiment Station. One of the samples was a 175-lb composite, which was designated Ore 1556. The other four samples were 7-lb grab samples that had been obtained from four different exploration pits. They were designated Ore 1626, Lots 1 through 4. Basic Mineralogy: Many authors have reported that the rocks of the so-called gabbro of the Duluth Intrusion vary widely in composition.8-9 The samples on which our studies were based also contained a wide range of rocks. A gabbro, olivine-gabbro, anorthosite-gabbro, norite, and a troctolite were represented. The essential minerals in the samples were plagio-clase, pyroxene, and olivine, in variable proportions.

Jan 1, 1969

The 116th (New York) Meeting of the Institute will be held in the third week of February, 1918. The Committee on Papers and Publications has set Dec. 1, 1917, as the closing date for the receipt of .manuscripts intended for this meeting. Manuscripts must be received by the Secretary on or before this date. If they are sent through members of the technical committees they must be sent to those committees enough in advance of the time to be forwarded and in the. hands of the Secretary by the time specified.

Jan 11, 1917

By Henry A. Mather

While this device is not new in its inception, its peculiar advantages failed to be of practical utility until furnace-builders instituted the mechanical reform of supporting the upper and lower water-jackets by hanging them from an I-beam frame, independently upheld by iron columns, instead of resting the entire weight of structure on the bottom, as practice formerly prescribed. The Colorado Iron Works were among the first to build copper-furnaces of this description, and the device, illustrated herewith, has been installed by them in three recent plants,—two furnaces for the Westinghouse interests near Ely, Vermont, and one for the Grand Prize Copper Company, of Gila county, Arizona. The jack-screw supports (Figs. 1 and 2) and the familiar iron bottom of former practice are retained as integral parts of this new furnace-bottom. And, instead of resting inert on the tapfloor of the furnace-room, the jack-screws are supported on and bolted to two I-beams the length of the furnace, placed immediately beneath, and parallel to, its sides. These I-beams are bolted to, and supported by, three steel axles equipped with small flanged wheels, the whole constituting a carriage, which runs freely on a track. The entire apparatus is movable or rigid at will, for the wheels are easily braced, if the tension of the tightened jack-screws does not serve to hold the whole in position. The advantages of this design will be at once apparent to those who have had practical experience in barring furnaces provided with stationary iron bottoms. It is a well-known fact that the larger part of the time occupied in cleaning and preparing a frozen furnace for active service is necessitated by working in a confined place where the temperature is uncomfortable, and that in such case the débris must be removed from

Jan 1, 1903

By H. R. Hanley

THE characteristics of alloyed anodes and their influence on the products of electrolysis and power consumption have been noted previously in the literature.1 This paper presents data in continuation of the subject given in an earlier paper by the authors.2 As noted in the authors' previous paper, the objectives of this work are the reduction in the cell voltage and the purity of the cathode product resulting from the use of alloyed lead anodes. The fundamental facts developed in the previous paper were: (1) that the presence of a small amount of calcium lowers the anode potential approximately 50 per cent. below that of pure lead; and (2) that thallium when present to the extent of 4 per cent. rendered the anode practically stable, thereby lowering the contamination of the cathode by lead to a very insignificant amount. The specific features determined in this recent work are as follows: 1. The lowest limit of calcium in the lead which will still give maximum lowering of the anode potential. 2. The characteristics of the thallium-calcium-lead anode. 3. The characteristics of the silver-calcium-lead anode. 4. The characteristics of the thallium-silver-calcium-lead anode. It was determined that 0.1 per cent. calcium in the anode was sufficient to lower the anode potential approximately 50 per cent. Table 1 shows the characteristics of alloyed anodes tested. The anode composed of 0.1 per cent. calcium, 4 per cent. thallium, and 95.9 per cent.

Jan 1, 1931

By Kung-Lee Wang, Brian W. Mackenzie, Warren E. Morrison, DeVerle P. Harris, George F. Sharrard

The term "mineral economics" is applied to a wide range of activities in the mineral industries. Earlier chapters have described the application of economic concepts to the mineral industries-supply, demand, conservation, tariffs, etc. The solution of mineral economics problems is often assisted by the application of quantitative methods. The purpose of this chapter is to describe a number of quantitative methods-econometric, operations research, and management science techniques-which find application in the analysis of mineral economics problems. These methods include input-output analysis, trend analysis, forecasting techniques, simulation, multivariate statistical analysis, mathematical programming, and market research techniques. The purpose of this introductory section is to provide a mineral economics framework for the application of these methods. Mineral economics is a subdivision of economics that is justified by a sufficient number of economic problems in the mineral industry requiring special experience and an unusual combination of skills. These problems are concerned with the conversion of minerals as geologic resources to minerals as economic goods. The mineral conversion process is outlined in Fig. 8.A.1. The physical occurrence of mineral deposits in nature and the market demand for mineral products in the economy provide the basic stimuli. The conversion process embodies a number of sequential stages-exploration, the development of mineral deposits, and mineral processing facilities and, consequently, productive activity to supply market demand. Changes in demand and the depletion of deposits illustrate the dynamics of the process. Mineral economics applies economic con-

Jan 1, 1976

By W. A. Ver Wiebe

The year 1939 in Kansas, with a production of 57,944,300 bbl. from 19,669 wells, shows a slight recession from the peak of oil production reached the previous year, when slightly over 59,000,000 bbl. of oil was marketed. The previous peak had been reached in 1917 with 45,451,000 bbl. marketed. Another still earlier peak had been reached in 1904, when slightly less than 5,000,000 bbl. was produced and sold. The production of gas probably reached a new peak during 1939 with a total of over 69 billion cubic feet. Between the peak of the year 1908, when over 80 billion cu. ft. was produced, and that of 1939 the production dropped to 16 billion cu. ft., in the year 1921. During the year 1458 wells were drilled. This figure is somewhat lower than that given in several trade journals, because it does not include wells that were deepened or recompleted in a different geological horizon. Nearly 75 per cent (1029) of the total number of wells were completed as commercial oil wells (824 in western and 205 in eastern Kansas). The commercial gas wells completed number 71, of which 24 are in eastern Kansas and 47 in western Kansas. The remaining completions include 154 dry holes in eastern and 204 dry holes in western Kansas. Based on daily potential capacity the new discoveries of the year accounted for a cumulative initial production of 264,000 bbl. in eastern and 1,158,827 bbl. in western Kansas. It is interesting in this connection to note that the number of wells completed in the state rose gradually to a first peak in 1904, when 2782 were drilled. The number dropped off rapidly to 368 three years later, but rose to the second and highest peak in 1918, when 4671 wells were completed. In the period between 1904 and 1912 more gas wells than oil wells were completed. Between the high peak of 1918 and the somewhat lower peak of 1937, the low point was reached during 1931 with the completion of only 470 wells. In the matter of new pools discovered, Kansas again ranks high. The exact number depends somewhat upon the interpretation of a "new" area—whether it should be called a new pool or a long extension of an older pool. In some places this determination cannot be made until more wells are drilled within the area. Therefore, the figures given

Jan 1, 1940

By W. A. Ver Wiebe

The year 1939 in Kansas, with a production of 57,944,300 bbl. from 19,669 wells, shows a slight recession from the peak of oil production reached the previous year, when slightly over 59,000,000 bbl. of oil was marketed. The previous peak had been reached in 1917 with 45,451,000 bbl. marketed. Another still earlier peak had been reached in 1904, when slightly less than 5,000,000 bbl. was produced and sold. The production of gas probably reached a new peak during 1939 with a total of over 69 billion cubic feet. Between the peak of the year 1908, when over 80 billion cu. ft. was produced, and that of 1939 the production dropped to 16 billion cu. ft., in the year 1921. During the year 1458 wells were drilled. This figure is somewhat lower than that given in several trade journals, because it does not include wells that were deepened or recompleted in a different geological horizon. Nearly 75 per cent (1029) of the total number of wells were completed as commercial oil wells (824 in western and 205 in eastern Kansas). The commercial gas wells completed number 71, of which 24 are in eastern Kansas and 47 in western Kansas. The remaining completions include 154 dry holes in eastern and 204 dry holes in western Kansas. Based on daily potential capacity the new discoveries of the year accounted for a cumulative initial production of 264,000 bbl. in eastern and 1,158,827 bbl. in western Kansas. It is interesting in this connection to note that the number of wells completed in the state rose gradually to a first peak in 1904, when 2782 were drilled. The number dropped off rapidly to 368 three years later, but rose to the second and highest peak in 1918, when 4671 wells were completed. In the period between 1904 and 1912 more gas wells than oil wells were completed. Between the high peak of 1918 and the somewhat lower peak of 1937, the low point was reached during 1931 with the completion of only 470 wells. In the matter of new pools discovered, Kansas again ranks high. The exact number depends somewhat upon the interpretation of a "new" area—whether it should be called a new pool or a long extension of an older pool. In some places this determination cannot be made until more wells are drilled within the area. Therefore, the figures given

Jan 1, 1940

By Alden B. Greninger, Alexander R. Troiano

Metallurgists have long believed that martensite in steel forms as plates along the octahedral {111} planes of austenite. Much has been written about mechanisms whereby units of the austenite lattice are pictured as transforming to martensite by shearing movements initiated along the octahedral planes of austenite, supposedly resulting in plates of martensite lying parallel to these planes of shear. A critical inspection of two or three photomicrographs of quenched hypereutectoid steel led us to the conclusion that the orientation habit of martensite, at least in hypereutectoid austenite, could not possibly be octahedral. Inasmuch as recent studies,30,31 of the martensite-type reaction in nonferrous alloy systems have established the irrational orientation habit as characteristic of this type of lattice transformation, the need for a thorough restudy of the crystallography of martensite formation in steel was evident. The present paper reports the results of such a study, extended to include both cementite and some of the products of constant-temperature decomposition of austenite. Also reported are a few of the results obtained from a microscopic and X-ray study of the austempering process in very high-carbon steel. I. The Martensite Transformation Previous Work Microstructure and Crystal Structure of Martensite.—Among the best series of published photomicrographs of quenched steels are those of Whitely,1 Robertson,2 Hanemann and Schrader,3 and Lucas.4 The crystal structure of martensite is body-centered tetragonal, with axial ratio varying from 1 near 0.0 per cent carbon to 1.08 for 1.75 per cent

Jan 1, 1940