Search Documents

By P. Datta, L. L. Handy

For a wetting phase displacing a nonwetting phase from a porous medium the distribution of the residual fluid may depend on displacement conditions. Although this subject has been debated in the literature, only a few experiments have been cited to support the various conclusions. Experimental results presented in this paper show that fluid distributions are dependent on imbibition pmcedures. Results agree qualitatively with predictions from the pore doublet model. If the rate of water imbibition is restricted, the nonwetting phase is trapped preferentially in .the larger pores as expected. But if the rate of water imbibition is unrestricted, trapping occurs somewhat more in the smaller pores. These conclusions were deduced primarily from relative permeability measurements. INTRODUCTION Relative permeabilities are known to depend on the saturation history of the porous medium. For either continuously increasing or continuously decreasing wetting phase saturations, however, they have normally been assumed to be single-valued functions of saturation. Severat investigators have compared relative permeabilities measured by different methods and have reported acceptable agreement.1-5 Studies of simple models of the displacement process suggest that the distribution of residual fluids can be influenced by the displacement method. If this is so, relative permeabilities also should depend on the method of displacement. These predictions have not been supported by experimental data. The object of this paper is to investigate experimentally some of the predictions of these model studies. The particular question of importance is whether steady-state and unsteady-state methods should be expected to give the same values of relative permeability. Much of the reported data showing agreement between steady-state and unsteady-state methods have been obtained on un consolidated sand. Johnson, Bossler and Naumann, however, compared steady-state and unsteady-state results for Weiler sandstone and found no significant differences.5 Levine made a detailed study of pressure and saturation distributions for a laboratory waterflood in a consolidated system but made no attempt to calculate performance from steady-state relative permeability data Bail and Marsden in a somewhat similar set of experiments did attempt a comparison of observations with predictions but the results were inconclusive.7 Excluding gravity, two forces affect the distribution of wetting and nonwetting phases during an unsteady-state, immiscible displacement: viscous and capillary forces. If relative permeabilities are indeed the same when measured by steady- or unsteady-state methods, the fluid distributions at the same fluid saturations must be similar for both methods. Furthermore, the implication is that the relation between capillary and viscous forces is the same for both methods insofar as the effect on microscopic fluid distributions is concerned. Unsteady-state displacements are normally run at high rates to maximize the ratio of the viscous to capillary forces. The objective is to reduce the effect of capillary forces on macroscopic fluid distributions. For floods in which the phase which wets the porous medium displaces the nonwetting phase, capillary forces compete with viscous forces in determining fluid distributions.8 The residual nonwetting phase is discontinuous. Competitive aspects of viscous and capillary forces and the resulting effect on water-oil distribution in porous media have been illustrated in an elementary way using a pore doublet model. This model and predictions from it have been discussed at considerable length by Rose and Witherspoon, Rose and Cleary and by Moore and Slobod.9-13 Rose and Witherspoon show that so long as water invades the model at a rate equal to or greater than the free imbibition rate, the water will move through the larger capillary of a doublet first and trap oil in the smaller capillary. On the other hand, if a negative pressure is applied to the water

Jan 1, 1967

By K. H. Ribe

Water often enters an oil reservoir during completion or workover operations on a well and forms a partial "water block" to oil production. A mathematical study of radial two-phase flow, neglecting capillary effects, has been employed to study the formation of such a water block and subsequent re-moval by production from the well. The effects of reduced oil permeability about the well on the well productivity were studied. The fluid saturation distributions about the well during formation and removal of the water block have also been computed. Several relative permeability relations and viscosity ratios were employed. If water has invaded the formation, its influence through relative permeability effects alone can cause the following. 1. Oil productivity will be depressed for extended periods after production is resumed and will build up only gradually as the water is removed. 2. Oil injected for treatment of water blocking will delay rather than promote restoration of full well productivity by enlarging the region invaded by water. Thus, unless the specific action of chemicals contained in the oil is needed, oil injection appears undesirable. INTRODUCTION During oilwell workover operations, water may enter the oil-bearing formation from the wellbore. When production is resumed, oil must flow through the region invaded by this water. The presence of this region can cause both well productivity and oil production rate to be low and oil to be produced with high water-oil ratio for some time after production is initiated. This situation is sometimes described as a water block. The introduction of water into the formation may result in other actions which also lead to reduction in well productivity and which are also usually included in the connotation of the broad term, water block. Often considered, for example, are the possibilities of clay swelling by contact with fresh water and the formation of emulsions with the formation oil. If it is suspected that such specific actions have taken place, remedial treatments are undertaken which usually involve the injection of chemicals in oil. Since the introduction of water, even in the absence of specific interactions with the formation or oil, will cause a temporary water block (which might be misinterpreted as evidence of a more severe situation), it is of importance to evaluate the magnitude and duration of this blocking which results purely from the reduction in relative permeability to oil in the vicinity of the wellbore. It is also of interest to evaluate the effect of oil injection on the productivity of a well blocked by water in this manner. Inasmuch as this unfavorable condition may persist for some time, it may lead to premature condemnation of a workover or premature abandonment of a potentially productive pay zone. A quantitative evaluation of the influence of water entry on the oil productivity through changes in relative permeability was made by solving a radial form of the Buckley-Leverett equation. The distribution of water saturation around the wellbore during the entry of water was calculated and was followed by a similar calculation of the saturation distribution during the period of resuming production. At any stage in the removal of the invading water, knowledge of the distribution of its saturation permitted calculating the attendant loss in oil productivity. The influence of the shape of the relative permeability relationships was also evaluated by carrying out the calculations for two hypothetical cases. Further, the effect of the oil-water viscosity ratio was examined by repeating the calculations, for several ratios of unity and greater, with the same relative permeabilities. Fi-nally, results are presented to show how the length of time a well must be swabbed to resume production depends on the length of time it has been subjected to invasion by water. STATEMENT OF THEORY Differential Equations Water is assumed to enter a producing formation which is initially at the connate-water saturation and contains no gas. The water and oil are treated as in-

By Raymond L. Orr

Calorimetric measurements have been made of the heats of solution of gold axd indium in a number of liquid tin-rich alloys at a temperature of 705°K. Relative partial molar enthalpies of gold were determined as a function of dilute solute concentrations in the binary Au-Sn system and in the ternary Ag-Au-Sn and Au-In-Sn systems. Relative partial molar enthalpies of indium were determined for dilute solute concentrations in the In-Sn, Ag-In-Sn, and Au-In-Sn systems. Through application of the interaction coefficient concept introduced by Wagner and more recently extended by Lupis and Elliott, ualues have been obtained for the Au-Au, Ag-Au, Au-In, and Ag-In enthalpy interaction coefficients in liquid tin. The results are inte@reted in terms of solute atom distributions through comparisons with the predictions of dilute solution models. INTEREST in the thermodynamic behavior of dilute liquid alloys stems from two primary sources. From a practical viewpoint, it is often of importance to know or to be able to predict the effect that one solute will have on the thermodynamic properties of the other solutes in a multicomponent system. Studies of dilute solutions may also be rewarding from the theoretical point of view. Some of the difficulties arising from the more complex interactions possible in concentrated solutions are avoided, leading to easier interpretations in terms of solutibn models and bonding energies. For example, in a binary alloy the limiting values of the partial molar properties of the solute represent the case for which each solute atom is completely surrounded by atoms of the solvent, and no other interactions are possible. Solute - solute interactions in dilute solutions are conveniently treated by the interaction coefficient concept of ~agner.' Using a Taylor series expansion for the logarithm of the activity coefficient, In yi, of a component, i, in a solution consisting of dilute solutes with atomic fractions xi, xj, xk, and so forth, in a solvent, s, and neglecting the second- and higher-order terms, Wagner obtained the expression: Where Wheyz is the limiting value of yi in the pure solvent, s. The interaction coefficients, e:, e:, and so forth, are defined by: Since yi is related to the excess partial molar Gibbs energy of component i by GfS = RT In yi, E: is re- ferred to as the "Gibbs energy interaction coefficient". Lupis and Elliott~ extended Wagner's treatment to the relative partial molar enthalpy, aHi, and the excess partial molar entropy, qS. They defined the enthalpy interaction coefficient as: and the excess entropy interaction coefficient as: leading to expressions similar to Eq. [I]: The three interaction coefficients are related by? The self-interaction coefficients, E:,qf,and at, represent the effects of interactions between atoms of component i in solvent s; €3, q{, and 03 represent the effects of interactions between i and j atoms in solvent s; and so forth. From the Maxwell-type relationships between partial molar quantities, it may be shown1'2 that e{ = ej, r}\ =tj), and ai - crj. Experimental determination of the interaction coefficients requires extremely precise measurements of the appropriate properties as functions of solute concentrations in very dilute regions. Few such data exist for intermetallic alloys, even for binary systems, because of experimental difficulties. This is especially true with respect to enthalpy data for dilute alloys. Examination of the compilation of data for binary alloys by Hultgren, Orr, Anderson, and ~elle~~ reveals that determination of limiting values of &fii(Xi =0) often requires extrapolations to infinite dilution from xi = 0.05 to 0.10. Direct measurements of the enthalpy interaction coefficient, qi, for multicomponent systems are virtually nonexistent. This quantity is of course subject to direct calorimetric measurement, but its determination must be limited to cases where high experimental precision is possible. The heats of solution of gold and indium in liquid tin can be measured with relatively high precision, which makes determinations of 73 involving these metals as the measured solutes experimentally attractive. This paper presents the results of such determinations of the Au-Au, Ag-Au, Au-In, and Ag-In enthalpy interaction coefficients in liquid tin. MODELS FOR DILUTE-SOLUTION BEHAVIOR Random-Solution Behavior. In the quasi-chemical treatment of solutions, only nearest-neighbor bonds are considered, and a composition independent value

Jan 1, 1967

By John F. Allan

This paper does not pretend to advance any facts or improvements not known to many members of the Institute, but is intended merely to give a few practical hints on preliminary tests, and to call attention to a possible enlarged field for the cyanide process in the treatment of some silver-ores, which merits investigation. Broadly considered, the choice of a process for the treatment of silver-ores in Mexico is confined to the following alternatives: (1) Concentration for treatment by smelting; (2) milling and pan-amalgamation; (3) the patio and Ortega process; [4) chloridizing roast and lixiviation; (5) chloridizing roast and cyaniding; and (6) cyaniding of the crude ore. These methods of treatment may also be combined, and cyaniding or concentration, or both, may be introduced, at what-ever stage it is found to be most advantageous. The characteristics of the ore (especially its gold-content) and local conditions, such as distance from railway, cost of fuel, amount of water available, vary so much that it is impossible to make general comparisons between the different processes, either as to extraction or cost. Concentration and subsequent smelting may be made very expensive by long-distance transportation of concentrates; pan-amalgamation is undoubtedly expensive; and the patio process is barred when the ore contains appreciable amounts of gold, by reason of its poor extraction of that metal; yet there are many ores for which each of these processes is especially adapted, and the expense of treatment is compensated by the results obtained.

Jan 1, 1905

By Frederick Laist

THE ore from the Butte mines of the Anaconda company is quite siliceous; that is, it contains considerably less iron than is needed for the fluxing of the silica. The direct smelting of this ore, therefore, requires the addition of considerable fluxing material. The only flux available in sufficient quantity at Anaconda is limestone containing no metallic minerals. This necessarily makes the direct smelting of the ore so expensive that it is more profitable to subject the ore to a preliminary treatment by concentration. However, as the losses in the concentrator were very high, compared with the losses in the blast furnaces, it was found, by calculation, more profitable to send ores containing more than a given percentage of copper to the blast furnaces, in spite of the higher costs of treatment. The dividing point was dependent on various factors, the chief of which was the prevailing market price of -copper. It was customary, therefore, to segregate the ore as mined into two classes. Ore in the first class generally contained 5 per cent. or over of copper;: this was sent directly to the blast-furnace department. Second-class ore contained less than 5 per cent. of copper, and averaged around 3 per cent.; it went to the concentrating department. With the introduction of the flotation process, it was found possible to maintain an average recovery, as concentrates, of 96 per cent. At the same time, the cost of reverberatory smelting was very materially decreased by the use of pulverized coal. These two changes in practice made the blast furnaces unable to compete with the reverberatory furnaces on a cost basis. The distinction between first-.and second-class ore was therefore abandoned, and the ore was treated by concentration. Obviously, on ores as high in iron as the Butte ores, the concentrator, produces a product that is self-fluxing; in fact, it is possible to produce a

Jan 1, 1920

By N. A. Zeigler

GRaphitization phenomena occurring in solid cast iron have principally been studied from the angle of the reactions taking place during annealing of white castings in the manufacturing of malleable iron. The selected bibliography at the end of this paper presents the high spots of the published information in this field. Graph-itization of gray iron upon reheating has received much less attention, primarily because only on rare occasions is this material subjected to any kind of industrial heat-treating. Moreovcr, articles made from gray iron are seldom used commercially at temperatures when any graphitization can take place. When used in such conditions, it is assumed that the articles can be replaced at frequent intervals, which can be afforded because of the low cost of gray iron. However, there is at least one commercial process in which articles made from gray iron, during their manufacturing processing, are subjectcd to rather high temperatures; that is, manufacturing of cast-iron enamelware, which is glazed at about 1600° to 1700°F. (870' to 930°C.) From practical experience, it has been found that one of the convenient and economical compositions of gray iron suitable for enameling is, in round figures, as follows: Si, 2.50 per cent; Mn, 0.35; S, 0.07; P, 0.80; T.C., 3.35; C.C., 0.70. Since this iron usually is cast into thin-walled sections, the percentage of com- bined carbon in it is relatively high. Upon heating in the enameling furnaces, this combined carbon graphitizes, which causes permanent dimensional changes of the articles. Obviously, from practical considerations, it is desirable to maintain these dimensional changes as constant as possible. In the course of experimentation with this iron, two series of experimental heats were prepared in which the manganese to sulphur ratio of the standard cupola metal was offset by ladle additions of: (I) progressively larger amounts of sulphur, and (2) progressively larger amounts of manganese. Each one of these ladle charges was cast into experimental plates 8 by 4 in. and about 5/16 in. thick. All told, 13 ladle charges were thus treated. All of them are listed in Table I, together with their chemical analyses. It may be noted that the manganese to sulphur ratio in these samples ranges between 1.2 and 30.2. Every one of these compositions was subjected to thermal allalysis, using an automatic, self-recording differential dila-tometer. The specimens used in this instrument are 50 mm. long and 4 mm. in diameter. During the dilatometer cycle they are kept under a vacuum of about 3 microns. Each one of them was subjected to a thermal cycle by heating it to I830°F. (1000°C.) in 3 hr. and cooling to room temperaturc in 5 hr. Figs. I, 2 and 3 present three automatically recorded dilatometer curves for irons: Serial No. I (normal composition), Serial No. 6 (high sulphur), and Serial No. 13 (high manganese). All three of these figures are

Jan 1, 1945

By Wm. C. Coffin

THE refractory linings of open-hearth steel furnaces above the bath line are subject to severe wear not only from the heat caused by the combustion of the fuel and the reactions of the bath, but also from the melting action of the gases when not controlled and directed, and from the scouring of the oxides, etc. with which the products of combustion are charged. The framework that encases or binds the furnace is made up primarily of an iron or steel pan in which the furnace proper is built, side and end buckstays, and tie-rods. The expansion and contraction are so great and variable that the bindings may be subjected to severe stresses unless the tie-rods are carefully adjusted in heating up the furnace, but they are most affected by direct heat and usually become deformed from that cause when the lining is worn thin and, sometimes, when sections of the lining fall in and expose some of the framework. A deformed framework displaces the skewback of the roof arch and tends to distort or crush the roof. Bent buckstays deform the front wall, causing the door frames to stand away from the lining so that the gases burn between the lining and the frames, destroying both of them. Frequently the frames are attached to the buckstays; then when the latter bend the frames usually break. Preventing the distortion of the framework and maintaining the economy of the refractories are real factors in the cost of steel making. Not only does the cost of general repairs and reconstruction add directly to the cost of steel produced, but the time lost in making repairs cuts clown the steel production and increases the overhead expense of both the furnace shop and its allied foundry or mills. Many years ago water-cooled equipment applied to iron blast furnaces made it possible to increase greatly not only the size and production of the furnaces but also the life of the lining. It also cut down the loss from frequent repairs. The open-hearth furnace is a much later invention, especially as a commercial factor; for though it dates from the Fred Siemens patent of 1856, much more progress was made in the Bes-

Jan 2, 1919

By C. S. Giggins, F. S. Pettit

The oxidation of Ni-Cr alloys in 0.1 atm of oxygen has been studied at temperatures between 800" and 1200°C. For alloys with 30 wt pct or more Cr, continuous layers of Cr2O3 are formed during oxidation. In the case of alloys with chromium concentrations between approximately 5 to 30 wt pct, external scales of Cr203 are formed over grain boundaries whereas internal precipitates of Cr2O3 and external layers of NiO are formed at other areas on the alloy surface. When such conditions are present on the alloy surface, chromium diffuses laterally from those areas covered with a continuous layer of Cr2O3 to areas where a Cr2O3 sub scale exists and it is possible for the sub-scale zone to become separated from the alloy by a continuous layer of Cr2O3. Whether such a state will be attained depends upon the initial grain size of the alloy and the oxidation time. When the concentration of chromium in the alloy is less than 5 pct, Cr2O3 is formed internally both at grain boundaries and within the interior of grains and the alloy is covered with an external layer of NiO. MECHANISMS which describe the growth of oxide scales on nickel-base superalloys are complex and the effects produced by the various elements in these alloys on the oxidation behavior of superalloys are not clearly understood. In order to determine the influence of the different elements on the oxidation behavior of superalloys, it is first necessary to examine the oxidation properties of binary nickel-base systems which contain the principal elements present in the superalloys and then progressively more complex systems until compositions typical of the superalloys are attained. Chromium is present in virtually all nickel-base superalloys and the purpose of the present studies was to examine the selective oxidation of chromium in Ni-Cr alloys. The oxidation characteristics of Ni-Cr alloys have been extensively studied1-" to date principally as a result of the high oxidation resistance exhibited by some of these alloys. Ni-20Cr* has long been known *All compositions are given as wcight percent unless specified otherwise. to be oxidation resistant and is commonly used as resistance heating elements for service temperatures up to 1100°C. This alloy cannot be used for extended periods of time at higher temperatures because of the apparent reaction of the external scale with oxygen to form gaseous CrO3. In spite of the considerable work cited above some important aspects of Ni-Cr oxidation still remain unresolved. Virtually all of the previous studies agree that small additions of chromium to nickel, e.g., <10 wt pct Cr, result in increased oxidation rates as compared to that of pure nickel, whereas larger additions, e.g., 20 to 30 wt pct Cr, form alloys with substantially lower oxidation rates. The controversial aspects of the oxidation mechanisms for these alloys that still remain unresolved are as follows: 1) A description of the oxidation mechanism for the low chromium alloys. 2) A description of the oxidation mechanism for the high chromium alloys, particularly with respect to the composition of the external scale which results in the lower oxidation rates. 3) The specific alloy compositions at which the oxidation mechanism changes from that obtained for low chromium contents to that of the high chromium alloys and the reason for this transition. EXPERIMENTAL The Ni-Cr alloys listed in Table I were prepared from high purity metals by nonconsumably arc melting and casting as buttons. These alloys were then given a preliminary annealing treatment in argon at 815°C for 100 hr to promote homogeneity. Each button was cut into 0.250 in. thick sections that were subsequently cold-rolled to 0.050 in. thicknesses and annealed in argon at 815°C for 48 hr to provide a twinned, equi-axed grain structure. The grain size for these alloys was not uniform and the limits, within which the average grain size lies, are given in Table I for the single-phase alloys. All the alloys were single phase with the exception of the Ni4OCr alloy in agreement with the Ni-Cr phase diagram.&apos;&apos; Rectangular specimens were cut from the sheet to provide surface areas of approximately 2.5 sq cm. Exact areas were determined with a micrometer after surface preparation was completed. All of the specimens except the Ni-40Cr alloy and pure chromium were polished through 600-grit Sic abrasive paper, ultrasonically agitated in ethylene trichloride, rinsed with ethyl alcohol, and electro-polished. The specimens were electropolished in a 10 vol pct H2SO4 (conc), 6 vol pct lactic acid, methyl alcohol solution at 70" to 80°C for 2 min at a current density of 0.8 to 1.2 amp per sq cm. This electro-polishing procedure did not produce acceptable surfaces on the Ni-40Cr alloy nor on pure chromium and the oxidation properties of these materials were obtained for specimens polished through 600-grit Sic

Jan 1, 1970

By T. T. Quirke, L. C. McCabe

The object of the present investigation was to discover a physical basis for rank differentiation of coals, particularly the coals of the Illinois basin. Vitrainl was selected as the most appropriate coal material to use in the investigation, because of its homogeneity and ease of acquisition and handling. Previous Investigations.—Hoffman and Jenker2 have shown that their index of reflection is a characteristic of coal rank and that the Leitz slit microphotometer may be used in determining the different intensities of reflection. Zhemchuzhnikov3 measured the luster of several Russian coals with a color analyzer and found that the degree of luster was indicative of rank. Luster-volatile matter curves based on data from Sucan and Donetz coals were satisfactorily used for determining the rank or volatile content of other coals after the luster strength was determined. In 1934 Fisher4 reported refractive indices of 1.76 for bituminous vitrain and 1.87 for semibituminous vitrain. Investigation of Angle of Polarization.—Early in the present investigation several determinations of the refractive indices of the vitrains were made by immersing the minus 150 plus 200-mesh powder in oils. It was found that all the samples fell within the range 1.6 to 1.8. However, difficulty was encountered in securing oils in this high index range that were closely enough spaced to separate some of the coals. The writers made a number of determinations of the angle of maximum polarization from the polished surfaces of the vitrains and derived their refractive indices by the procedure described in the following paragraphs. Johannsen5 states the fundamental concepts underlying this procedure as follows: In general, in an isotropic medium light vibrates in all directions at right angles to the direction of propagation, and when it meets with another isotropic medium at an angle, part of the light is reflected and part refracted. It has been found that after reflection or refraction, the vibrations do not move with the same freedom in every

Jan 1, 1938

By E. L. Bruce

GOLD occurs in many mineral deposits in the rocks of the Canadian Shield. It is present in the ores of many base metals and a considerable quantity is recovered as a by-product from the production of copper at Noranda, of nickel and copper at Sudbury and of copper and zinc at. Flinflon. But the greater part of the gold production of Canada is from deposits in which gold is the only metal of value. No gold is obtained from placer deposits within the borders of the Canadian Shield. A brief review of the geological relations of some of the gold deposits of the Canadian Shield will be presented in an attempt to explain certain associations. Only those which are being worked for their gold content will be considered and descriptions will be conned to representative types of deposits, chiefly those of major importance; a few others, differ-ing in certain features from those of the older and larger mines, will be included in order to illustrate the general conditions in which gold occurs in these ancient rocks. Brief summaries will be given of the geological relations of the Beattie and Siscoe mines of northern Quebec, of the mines of the Porcupine and Kirkland Lake areas of northeastern Ontario and of the Howey, Central Patricia and Little Long Lac mines of northwest-ern Ontario. Genetic relations to igneous rocks of granitic composition, outcropping in the vicinity, have been assumed for many of these deposits. Undoubt-edly the ore minerals have been derived from igneous sources and, for some occurrences, there is evidence suggestive of genetic relationship between the ore bodies and neighbouring intrusive rocks. During the past few years, however,, many investigators have expressed doubt of the genetic relationship of certain ore bodies to igneous masses near which they occur. As will be seen from references in the following descriptions the importance of the structural conditions in localizing deposition has been realized. This is pointed out for Canadian pre-Cambriang old deposits by E. T. Dougherty, who also refers to the

Jan 1, 1937

By T. T. Quirke, L. C. McCabe

The object of the present investigation was to discover a physical basis for rank differentiation of coals, particularly the coals of the Illinois basin. Vitrainl was selected as the most appropriate coal material to use in the investigation, because of its homogeneity and ease of acquisition and handling. Previous Investigations.—Hoffman and Jenker2 have shown that their index of reflection is a characteristic of coal rank and that the Leitz slit microphotometer may be used in determining the different intensities of reflection. Zhemchuzhnikov3 measured the luster of several Russian coals with a color analyzer and found that the degree of luster was indicative of rank. Luster-volatile matter curves based on data from Sucan and Donetz coals were satisfactorily used for determining the rank or volatile content of other coals after the luster strength was determined. In 1934 Fisher4 reported refractive indices of 1.76 for bituminous vitrain and 1.87 for semibituminous vitrain. Investigation of Angle of Polarization.—Early in the present investigation several determinations of the refractive indices of the vitrains were made by immersing the minus 150 plus 200-mesh powder in oils. It was found that all the samples fell within the range 1.6 to 1.8. However, difficulty was encountered in securing oils in this high index range that were closely enough spaced to separate some of the coals. The writers made a number of determinations of the angle of maximum polarization from the polished surfaces of the vitrains and derived their refractive indices by the procedure described in the following paragraphs. Johannsen5 states the fundamental concepts underlying this procedure as follows: In general, in an isotropic medium light vibrates in all directions at right angles to the direction of propagation, and when it meets with another isotropic medium at an angle, part of the light is reflected and part refracted. It has been found that after reflection or refraction, the vibrations do not move with the same freedom in every

Jan 1, 1938

By H. Landsberg

IN a previous report1 it was pointed out that a successful attack on roof troubles has to be preceded by extensive scouting. As Lord Kelvin once said, scientific progress can be made only if accurate data are available: "unless you measure, you do not know.? THE CONVERGENCE RECORDER For the observation of roof movements in mines the convergence recorder has shown that it will enable us to get some of the necessary information. Results with convergence recorders were first published by Winstanley and other English investigators for rapidly moving longwall faces. In their investigations the speed of work and the heavy over-burden produced a considerable amount of absolute values of convergence in a short time. Under the conditions frequently encountered in our investigations in Central Pennsylvania, under shallow, overburden and in mines with slowly proceeding extraction, the movements observed were much less in absolute value, for an equal interval of time. This was partly because the mines in which our studies were carried on frequently had idle days, sometimes four or five in succession. Therefore continuous records were not employed and a simple convergence gauge was built. In its first models, it consisted only of two telescoping tubes pressed against roof and floor by a coil spring. At the side of the lower tube a rule divided into 1/-mm. divisions was fixed and a knife-edge, which was attached to the upper tube, was slid over the scale in case of convergence between roof and floor. While the larger motions could be read on this device, it seemed to be desirable to increase the accuracy by inserting between the two tubes a dial meter reading in 1/1000 in. Such a gauge was first built in April 1937 and installed for experimental purposes in a bituminous coal mine in Pennsylvania (Fig. 1). It was read at least once daily, 24 hr. apart, and if feasible at shorter intervals. After several months of experience it can be said that this type of gauge answers the scientific as well as the practical needs. It is easier to handle than the recorder; no clock is used, there are no pen troubles. The price of

Jan 1, 1938

By H. B. Bailey

SiNcE the gypsum deposits of Nova Scotia have been operated on a large-tonnage basis, it has become increasingly necessary that more study be given to the geological relation of gypsum to anhydrite. It was while attempting to work out some definite system of quarry operation for several operators that the factors relating to hydration as given in this paper became apparent. For convenience the words "the formation" are used to mean anhydrite and gypsum taken together as one bed geologically and forming a distinct unit from the rocks below or above. Also, the word "block" is used geologically to define a portion of the formation that is cut apart and separated by erosion from other portions. The formation is part of the Lower Carboniferous, the remainder of which is made up of red shales and shaly sandstones, coarse red conglomerates and limestones. Overlying the Lower Carboniferous are the even-bedded gray sandstones of the coal measures. To a large extent these sandstones have been eroded from above the formation and the usual cover is clay and unconsolidated sediments. The position of the limestone member which immediately underlies the formation usually furnishes the key to the general structure. Being harder, and subject to less erosion, it has a wider spread than the&apos;formation, and measures for dip read on it have a value which can not be applied to dips taken on gypsum or anhydrite. This limestone usually is not more than 25 ft. deep, but it has a remarkable tenacity—one would almost say elasticity—under strain of earth movements. In many cases it stands as a barrier to the erosion which otherwise would have destroyed completely the remaining block of the formation. No bedded limestone is found within the formation except in narrow seams close to the bottom and in short irregular masses in highly disturbed strata where it has been caught up by fault action. This paper is not concerned with the general theories of original deposition and no opinion is expressed as to whether gypsum or anhydrite was first deposited from evaporating sea water. For purposes of study, and as an observed fact, except in the few cases where there has been extreme disturbance, a block of the formation is regarded as a block of anhydrite which has become partly hydrated into gypsum. 177

Jan 1, 1931

By L. C. Weiner

For zinc single crystals, xo = 3o, a surface coating raises both the cleavage and yield strengths over a large temperature range. The "brittle temperature," associated with slip after completion of twinning, does not coincide with the point of intersection of the flow and cleavage curves, which is associated with twinning. A surface film has no effect on the brittle temperature, while it lowers the intersection temperature some 20°. For crystals, yn = 83o, a coating decreases the cleavage strength, making it temperature independent, as well as increases the brittle temperature or its equivalent, the intersection temperature, 20°. These observations are described on the basis of a dislocation-pile-up-at-a-barrier model for brittle fracture; in crystals x,, = 3o the number and distribution of twins play a vital role. IN a recent investigation on the effects of solid environments on the brittle fracture of zinc single crystals,&apos; it was demonstrated that the presence of a surface film changes the cleavage strength of these crystals, either increasing or decreasing it, depending on the crystal orientation. An increase in cleavage strength of some 43 per cent was found for coated crystals oriented x, — 3o K = 28",* while a decrease of 48 per cent was observed with crystals X" = y» — 83". Moreover, these effects were found

Jan 1, 1959

By W. N. Hiatt

The mathematical theory of the flow of two-phase, incompressible fluid through porous media is clarified, and the development of a general fluid displacement equation for two-phase, incompressible vertical flow through porous media is outlined. The relationship between the three components of the equation — the "fluid drive effect", the "gravity effect", and the "capillary effect&apos;&apos; — is discussed, as well as implications of the analysis in connection with the study of certain types of petroleum reservoirs. INTRODUCTION The purpose of this paper is to clarify and summarize the mathematical basis of the theory of two-phase incompressible fluid flow through porous media, particularly as it pertains to vertical flow, and to present a qualitative* exposition of the controlling factors involved in circumstances where this type of flow may exist. Although the generally accepted theory of heterogeneous fluid flow through porous media was developed a number of years ago by Muskat,1 and Buckley and Leverett2, 3 using the basic premise of Darcy, (and since then expounded upon by many others) there is a need for an over-all summary and clarification of this theory, especially regarding certain types of applications in connection with so-called "gravity-drainage-type reservoirs". The source and derivation is outlined for what is referred to here as the "General Fluid Displacement Equation for Incompressible Vertical Two-Phase Flow through Porous Media&apos;&apos;. This equation would apply under the condition where the pressure drop along the path of flow is negligible in comparison with the pressure level on the system, or where compressibility and solubility effects are negligible. These conditions exist ordinarily in gravity-drainage-type reservoirs. Specifically, it will be shown that this general equation may be developed directly from the basic equations, which, according to present theory, govern the general case of viscous heterogeneous flow through porous media. This general equation has appeared in the literature previously, but in most cases its development from basic theory is not indicated clearly, or the equation is presented in terms of groups of constants and variables involving reduced or dimensionless quantities. This presentation is expedient in cases of experimental or computer applications; but it may make it difficult for the practicing petroleum engineer to identify all the factors involved or to understand the relationships between them. Therefore, in the following development, only ordinary mathematical parlance will be used, and no terms involving groups of other equations or reduced or dimensionless quantities will be used. DERIVATION The following equations for two-phase oil and gas flow result from analogy with Muskat&apos;s general equations,** if solubility and compressibility effects are neglected, and if all volumes are considered in terms of reservoir conditions, and the water phase, if present, is considered to be immobile (or effectively a part of the porous medium.) In this case, the sum of the oil and gas saturations may be taken as unity, and the saturation of each phase is in terms of the total hydrocarbon saturation. Note that in Eqs. 1 and 2, and in the derivation following, z is taken as positive in the vertically downward direction,

Jan 1, 1969

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page I Wilkes-Barre, Pa * May, 1871 I 3 II Bethlehem, Pa August, 1871 I 10 III Troy, N Y November, 1871 I 13 IV Philadelphia, Pa February, 1872 I 17 V New York, N Y * May, 1872 I 20 VI Pittsburg, Pa October, 1872 I 25 VII Boston, Mass February, 1873 I 28 VIII Philadelphia, Pa * May, 1873 II 3 IX Easton, Pa October, 1873 II 7 X New York, N Y February, 1874 II 11 XI St Louis, Mo * May, 1874 III 3 XII Hazleton, Pa October, 1874 III 8 XIII New Haven, Conn February, 1875 III 15 XIV Dover, N J * May, 1875 IV 3 XV Cleveland, 0 October, 1875 IV 9 XVI Washington, D C February, 1876 IV 8 XVII Philadelphia, Pat June, 1876, V XVIII Philadelphia, Pa October, 1876 V 9 XIX New York, N Y February, 1877 v 27 XX Wilkes-Barre, Pa * May, 1877 vi 3 XXI Amenia, N Y October, 1877 vi 10

Jan 1, 1910

By L. K. Jetter, J. C. Ogle, C. L. McHargue

The preferred orientation developed in extruded aluminum rods has been studied as a function of extrusion temperature, extrusion speed, and position in the rod. Duplex <111> - <001> textures were developed for slow extrusion speeds at temperatures of 75° to 850° F and for fast extrusion speeds at temperatures of 75° to 450°F. The <001> texture component was shown to be primarily due to re crystallization occurring during fabrication. At fast speeds and billet temperatures of 650° to 850°F, complete recrystallization occurred and <115>or<118> textures were found. The nature of the structure has proved to be an important variable in the production and use of extruded products. Data on the flow of aluminum and aluminum alloys summarized by Smith,&apos; Hardy,&apos; and Locke3 show that the extruded product may possess a deformed, a partially recrystallized, or a completely recrystallized structure, and there may be important variations in the structure from surface to center and from front end to back end of an extrusion. This inhomogeneity in grain structure and preferred orientation affects both the mechanical properties of the extruded section and its response to subsequent heat treatment. Among the fabrication variables causing these differences are temperature, extrusion ratio, and extrusion speed. Preferred orientation which develops during the extrusion of rods is of the fiber-type and, in general, has been assumed to be similar to that developed in rods or wires fabricated by drawing through dies, rolling, or swaging.4 Because of the nature of the flow of metal being extruded, this assumption may be valid for material near the center of the rod but probably is not valid for the outer layers. In most face-centered-cubic metals a duplex fiber texture has commonly been reported in which the grains have either <Ill> or <001> directions parallel to the longitudinal axis. Sachs and fichiebold5 reported cold-drawn aluminum (99.6 pct pure) to have a single <Ill> fiber texture, and this observation was confirmed by Schmid and Wassermann.6 Hibbard, on the other hand, observed a minor <001> and a major <111> texture in 99.994 pct A1 cold drawn to 98 pct reduction in diam.7 He concluded that the <001> component resulted from a small amount of room-temperature recrystallization. Dayal8 concluded that the <001> component was an intermediate component which disappeared at high reductions in 99.5 pct pure Al. Kostron and schippers9 found duplex <111> — <001> textures in extruded 99.5 pct Al, as did Gow and cahnl0 and GOW11 for extruded rods of commercial and superpure aluminum. Similar duplex fiber textures have been reported for aluminum alloys by Kostron,= Unckel,13 and Van Horn.14 The present paper is concerned with the variation in texture with fabricating conditions and with the nature of the texture components in extruded aluminum rod (99.99 pct pure). EXPERIMENTAL PROCEDURE Ingots were chill-cast in cast-iron molds and machined to 3-in. diam by 6-in. long extrusion billets. These billets were upset to 3.125 in. diam and extruded through a flat-face 0.690-in. diam die. Quenching of the rods was accomplished by a water spray at the die face. The combinations of fabricat-

Jan 1, 1960

By P. K. Koh

Isothermal salt bath annealing of 0.014-in. thick 3 pct Si-Fe sheet was conducted at temperatures ranging from 927" to 1260°C in order to investigate the grain-growth behavior. Within the temperature range studied normal grain growth did not take place; instead nucleated grain growth prevailed. The nucleation frequency was found to increase with the annealing temperature, with corresponding decrease in grain diameter of ultimate secondaries after long-time annealing. Large secondaries grown by low-temperature isothermal annealing are essentially of (110)[001] orientation, and the (110)[001] texture is strong. The relatively small secondaries grown by high-temperature isothermal annealing also have orientations near (110)[001] as an average but widely scattered; thus the amount of (110)[001] texture is found to decxease with isothermal annealing temperature. Grain growth and texture development at various annealing temperatures can be described by families of sigmoidal curves with the time axis. ThE cube-on-edge (110)[001] texture and predominating large secondaries in fully annealed 3 pct Si-Fe are customarily produced by a 1100°C annealing of a primary recrystallized sheet. On annealing the primary recrystallized sheet above the temperature at which secondary recrystalliza-tion starts May and turnbull&apos; have demonstrated that secondary grains decrease in size as the temperature is increased. The phenomenon was attributed to a decrease in the (G/N) ratio where G is the growth rate of secondary grains and N is their nucleation frequency. In addition, the growth of grains in orientations rather far from (110) [0011 occurred. The present investigation is devoted to detailed rate studies of the same phenomenon. Mi-crostructure, magnetic anisotropy, and texture data were obtained on strips of 3 pct Si-Fe isothermally annealed for various lengths of time in a BaC12 salt bath at temperatures ranging from 927&apos; to 1260°C. The texture results are reported elsewhere.2 EXPERIMENTAL PROCEDURE Commercial 0.014-in. cold-rolled silicon-iron strip (3.16 pct Si), prepared by two stages of cold rolling with an intermediate short anneal, was given a decarburizing 3-min anneal at 800°C. Metallo- graphic studies indicated complete recrystallization. In order to provide a protective atmosphere and to obtain a rapid rise to an elevated temperature, a BaC12 and NaCl fused salt bath was used to heat samples isothermally at temperatures from 927" to 1260°C for various lengths of time. Torque magnetometer measurements were made on 1-in.-diam disc specimens before and after annealing, since magnetic torque curves supply information on textures and texture changes. Surface layers of the strip samples were polished and etched to reveal the grain structure. The diameters of grains were measured from micrographs at X100. The average value of diameters of matrix grains was established. Individual grains in the micrograph were cut out separately along grain boundaries. These grains were classified either as matrix grains or growth grains. The percent weight of growth grains in the cut-out patterns was reported as percent growth. Manv of the individual grains in the annealed samples were large enough to be X-rayed with a 5-mil beam for Lauegrams. Complete (110) pole figures were obtained for the primary recrystallized structure and short-time annealed structure with CoKa radiation at 30 kv in the back-reflection range, such as (220) for (110) poles, as described recently by Newkirk and ~ruce.~ Both the X-ray optics and the technique for pole figure differed slightly from those adapted previously.4

Jan 1, 1960

THE second part of the mould for making guns is the core. Without this the space could not be made where the powder is to be and through which the ball, impelled by the fire, can pass and take flight. To make this it is necessary to take two things into consideration, because they are very important. One is what you are to make it on so that it may be supported and kept true. The other is what composition of clay will stand up during casting and yet not be very difficult to extract from the body of the finished gun. For the first, it is found that only an iron spindle of a suitable thickness is able to support the weight of the clay without bending under the heat of the fire or wobbling as it is turned on its journals or when handled. This should be a braccio or more longer than the mould of the gun and worked exactly round, straight, and well tapered like a spindle; above all every one of its joints should be well secured and solid. At the upper end a per-orated heel should be made, and lower down, exactly at the point corresponding to the length of the mould, are one or two other holes through which the little crossbars can be passed that fasten the core to the outer mould and also serve for constructing the disc. Now this iron is to be arranged on two trestles, pivoted so that it may turn truly when rotated. In order that it may not run up and down, make a little iron fork which engages a notch made with a file at the foot, and another at the head. After this, you must prepare clay for the core which is well made and tenacious ,enough not to crack. Fint take care that there are no pebbles in it and that it is composed of a small amount of cloth clippings and much sifted horse dung and some washed and clean wash ashes so that it may be of a tender and crumbly consistency in order that it may later be more easily extracted from the space inside the gun. In the same way, in order that you may be able to take out the iron piece at the same time, first cover it with ashes, and then wrap it all over with a rope of ordinary thickness, leaving a dito of the iron uncovered in every palmo length. [86] Alternatively, you may cover it all very tightly with hemp tow in the same way after it has been covered with ashes. Or heat your iron considerably and then cover it all to the thickness of a good cord with wash ashes or powdered charcoal that has been made into a paste with a little

Jan 1, 1942

By G. C. Mudd, E. J. Myers

Within the last 15 years David Brown Gear Industries has manufactured approximately 200 large mill gears over 6m diam., 58 of them over 9 m and up to 12 m diam. The experience has not been without problems, due to a lack of clear understanding of the loads and stresses imposed on large gear wheels. American Gear Manufacturers Association (AGMA) practices suggest that a service factor be used for mill gears. But what is meant by "service factor"? The layman might be forgiven for believing that the term is synonymous with "safety factor," but this is certainly not true. The service factor is an aggregate of the following in some proportion: -An application factor, i.e., an allowance for the fact that systems do not run smoothly with uniform torque. -An ignorance factor covering the imperfections in the basic gear calculation. -Possibly a safety factor. In the following sections some of the ways in which the limits of applicability can be overstepped are discussed.

Jan 1, 1983