Search Documents

By Rudolf Kudlich

The problem of eliminating the hazards of hoisting in mines has been with us since the industry passed its earliest stages, when coal and ore could be won from surface working and tunnels. At first, safety devices were introduced as means of decreasing the amount of labor necessary to produce the mineral, or to increase the amount that could be obtained from a certain opening. For example, crude ladders replaced winding footpaths or steps cut into the walls of the pit or shaft, decreasing the distance it was necessary to carry the product to the surface and eliminating, to some extent, the hazard introduced by the precarious footing afforded by such paths and steps. Latcr, instead of being carried from the pit on the backs of men, the product was hoisted in buckets or baskets on a rope passing over a pulley or around a windlass. Thus the capacity of the pit was considerably increased, and the hazard due to making many trips up and down the shaft was eliminated. From such beginnings accident prevention in mine hoisting advanced with the importance of the industry, until at present hoisting compares favorably with other branches of the mining industry with reference to safe practices. As in the other branches, this progress has been accomplished along two general lines—by legislation, rules, and education, and by the installation of safety devices. Though due credit must be given the former, it is not so satisfactory as the latter. Legislation, to be effective, requires a policing and inspection system to guarantee enforcement, such as we cannot hope to inaugurate. Rules may be satisfactory so long as the employer controls the labor market, and dismissal or some other form of discipline is an effective means of insuring obedience to the rules; but where labor demand is in excess of the supply, or where labor organizations are in control, such measures are not effective. An educational campaign will draw attention to hazards and may awaken a desire to avoid accidents by exercising the proper care. It is necessary, therefore, to place our reliance mainly on mechanical devices to prevent accidents, and to depend as little as possible on laws,

Jan 1, 1923

By Rudolf Kudlich

The problem of eliminating the hazards of hoisting in mines has been with us since the industry passed its earliest stages, when coal and ore could be won from surface working and tunnels. At first, safety devices were introduced as means of decreasing the amount of labor necessary to produce the mineral, or to increase the amount that could be obtained from a certain opening. For example, crude ladders replaced winding footpaths or steps cut into the walls of the pit or shaft, decreasing the distance it was necessary to carry the product to the surface and eliminating, to some extent, the hazard introduced by the precarious footing afforded by such paths and steps. Latcr, instead of being carried from the pit on the backs of men, the product was hoisted in buckets or baskets on a rope passing over a pulley or around a windlass. Thus the capacity of the pit was considerably increased, and the hazard due to making many trips up and down the shaft was eliminated. From such beginnings accident prevention in mine hoisting advanced with the importance of the industry, until at present hoisting compares favorably with other branches of the mining industry with reference to safe practices. As in the other branches, this progress has been accomplished along two general lines—by legislation, rules, and education, and by the installation of safety devices. Though due credit must be given the former, it is not so satisfactory as the latter. Legislation, to be effective, requires a policing and inspection system to guarantee enforcement, such as we cannot hope to inaugurate. Rules may be satisfactory so long as the employer controls the labor market, and dismissal or some other form of discipline is an effective means of insuring obedience to the rules; but where labor demand is in excess of the supply, or where labor organizations are in control, such measures are not effective. An educational campaign will draw attention to hazards and may awaken a desire to avoid accidents by exercising the proper care. It is necessary, therefore, to place our reliance mainly on mechanical devices to prevent accidents, and to depend as little as possible on laws,

Jan 1, 1923

By AIME AIME

DONALD K. CRAMPTON, present Chairman of the Institute of Metals Division, A.I.M..E., is well known by nonferrous metallurgists in all countries for his research work on the fabrication and properties of copper and its alloys including investigation of season- and stress- corrosion cracking. He is also well known, at least by many metallurgists in the United States for the proficiency with which be carries on his hobbies, in i:lrlditlg photography. gardening, and golf

Jan 1, 1941

By O&apos, M. M. Fine, K. G. Meara

One of the principal activities of the Bureau of Mines connected with the recent war was to help to increase the supply of strategic and critical minerals. Fluorite was one of the most critical of the nonmetallic minerals because of the increased demand for it as a flux in basic open-hearth and electric steel furnaces and as a raw material for the production of artificial cryolite used in the aluminum industry. Wartime developments in the technology of hydrofluoric acid, such as the use of the anhydrous acid as a catalyst in production of high-octane gasoline and the use of organic fluorides as carriers for insecticides, also increased the demand for acid-grade fluorite.f In 1943 the consumption of acid-grade fluorite was advancing at a more rapid rate than production, and was only slightly less than production during the latter half of the year.' The outlook for the postwar market for fluorite is encouraging. Steel production is expected to remain high until the domestic demand for commodities not manufactured during the war is satisfied. The uses for hydrofluoric acid are expected to increase under the impetus of war-initiated research. In considerbtion of these and other factors some authorities predict a postwar demand for fluorite equal to about 60 to 75 per cent of the wartime production.1,2 Others believe that the postwar fluorite industry will be permanently expanded over its prewar status.3 Acknowledgment This paper is one of many reporting on various aspects of the Bureau of Mines program directed toward the more effective utilization of our mineral resources. The program has been under the general supervision of R. S. Dean, Assistant Director, since July 1942. The scope of the paper falls in the province of the Metallurgical Branch, whose activities embrace the separation of difficultly beneficiated ores, the production of pure metals from domestic deposits, the exploitation of marginal orc reserves, the recovery of secondary metals, and the improvement of present industrial metallurgical practice. The investigation was initiated at the request of Mr. J. H. Steinmesch, vice-president and general manager, Minerva Oil Co., Eldorado, Ill. His hearty cooperation and helpful suggestions, and those of Mr. 0. E. Anderson, mill superintendent,

Jan 1, 1948

By K. G. Meara, M. M. Fine, O&apos

One of the principal activities of the Bureau of Mines connected with the recent war was to help to increase the supply of strategic and critical minerals. Fluorite was one of the most critical of the nonmetallic minerals because of the increased demand for it as a flux in basic open-hearth and electric steel furnaces and as a raw material for the production of artificial cryolite used in the aluminum industry. Wartime developments in the technology of hydrofluoric acid, such as the use of the anhydrous acid as a catalyst in production of high-octane gasoline and the use of organic fluorides as carriers for insecticides, also increased the demand for acid-grade fluorite.f In 1943 the consumption of acid-grade fluorite was advancing at a more rapid rate than production, and was only slightly less than production during the latter half of the year.' The outlook for the postwar market for fluorite is encouraging. Steel production is expected to remain high until the domestic demand for commodities not manufactured during the war is satisfied. The uses for hydrofluoric acid are expected to increase under the impetus of war-initiated research. In considerbtion of these and other factors some authorities predict a postwar demand for fluorite equal to about 60 to 75 per cent of the wartime production.1,2 Others believe that the postwar fluorite industry will be permanently expanded over its prewar status.3 Acknowledgment This paper is one of many reporting on various aspects of the Bureau of Mines program directed toward the more effective utilization of our mineral resources. The program has been under the general supervision of R. S. Dean, Assistant Director, since July 1942. The scope of the paper falls in the province of the Metallurgical Branch, whose activities embrace the separation of difficultly beneficiated ores, the production of pure metals from domestic deposits, the exploitation of marginal orc reserves, the recovery of secondary metals, and the improvement of present industrial metallurgical practice. The investigation was initiated at the request of Mr. J. H. Steinmesch, vice-president and general manager, Minerva Oil Co., Eldorado, Ill. His hearty cooperation and helpful suggestions, and those of Mr. 0. E. Anderson, mill superintendent,

Jan 1, 1948

By Walter W. Fisher, Samuel Rudy

Secondary treated sewage effluent was substituted for normal process water in laboratory tests simulating froth flotation recovery of copper and molybdenum sulfides. Sewage effluent caused significant detrimental response in the flotation process. First, a voluminous, uncontrollable froth was generated, even in the absence of a frothing agent, that has little mineral carrying ability. Second, sewage effluent caused a small loss in copper recovery and a large loss in molybdenum recovery. The detrimental effects of sewage effluent on flotation were partially overcome by tertiary treatment of the effluent by activated carbon adsorption and anion exchange. The frothing problem was significantly reduced after treating the sewage effluent by foam fractionation. Dilution of the effluent with normal process water resulted in a significant improvement in metal recovery. In addition, the large loss in molybdenum recovery was overcome by using a secondary collector in a combination reagent schedule. However, the secondary collector caused an appreciable loss in copper recovery.

Jan 1, 1979

By J. S. Aronofsky, R. Jenkins

A simple means of predicting the flowing well pressure history in a natural gas reservoir has been developed. The differential equation for unsteady radial flow of gases through porous media was solved by numerical methods using electronic punch card machines. The results obtained from these calculations are presented in a generalized form which is believed to be most convenient for engineering use. These results are compared with those presented in a paper by Bruce, et al4. An effective radius of drainage has been defined which permits the equation of steady state gas flow to be used easily to predict well pressures in gas reservoir depletion. An equivalent effective radius of drainage is defined for liquid flow systems and a comparison is made of the gas solution to the liquid solutions. INTRODUCTION This paper presents a numerical method for describing the transient flow of gases radially through a porous medium from which the production rate is specified. The results obtained from these calculations are presented in a generalized form which is believed to be the most convenient for engineering use. The principal application of these calculations should be to flow in natural gas reservoirs, in the interpretation of pressure drawdown tests, in the estimation of reserves, and in calculation of injection pressures required in gas injection and cycling operations. The evaluation of natural gas wells is based upon back-pressure tests in which measurements of production rate and flowing well pressure are made for periods of one, two, or more days. The flow is assumed to have stabilized at this time, and the observed values of pressure and production rate are used with standardized formulae to determine the well's allowable production rate. Furthermore, the results obtained from such a test of short time duration are extrapolated in such a manner to allow a prediction of what the well pressure will be at some future time for a specified (but possibly untested) flow rate. The manner of conducting such back-pressure tests suggests several questions as follows: 1. 'What is the definition of stabilized flow and what factors determine the length of time required for the flow to become stabilized? 2. How may the recorded values of pressure and rate be utilized? 3. As the well is produced and the reservoir pressure falls, how will the flowing well pressure change? Can this flowing well pressure be predicted from the back-pressure test? 4. Are the results obtainable from the test influenced by a particular procedure used in obtaining the results? 5. Is it possible to estimate the gross reservoir permeability from back-pressure data? It is not within the scope of this paper to provide solutions Or even to discuss adequately all the above questions. However. in considering such matters, the

Jan 1, 1955

By M. T. Simnad, R. F. Mehl, L. Yang

Techniques for studying marker movement in K-Rb interdiffusion have been worked out. The results indicate that Rb diffuses faster than K and that the ring mechanism of diffusion cannot be the dominant one operating in this case or probably in cases involving other alkali metals, despite their low ion core repulsive energies. SEVERAL theoretical attempts have been made in the past decade to elucidate the mechanism of diffusion in body-centered-cubic metals. No general agreement, however, has been reached by different authors. Zener,1 and later LeClaire,2 on the basis of a correlation between the entropy of activation for self-diffusion and the temperature dependence of the elastic constants, predicted that a ring mechanism should operate in the diffusion of body-cen-tered-cubic metals. Paneth3 calculated the activation energies of various ring, vacancy, and interstitial mechanisms for the self-diffusion in alkali metals and concluded that the most likely one was based on the linear motion of "crowdions," which is in fact a different form of interstitial diffusion. Fumi,1 however, showed that the experimental values of the activation energies for self-diffusion in the alkali metals could be better accounted for if the diffusion process in these metals was assumed to follow a vacancy mechanism. The same conclusion was reached by Kojima5 for the self-diffusion in lithium. Experimental evidences published during the past few years seem to exclude the ring mechanism as the predominating one in the diffusion of body-centered-cubic metals. For instance, maker movement has been observed in ß-brass, first in this laboratory" and later by Resnick and Baluffi.5 Shewmon and Bechtoldh also found marker movement in the body-centered-cubic system Ti-Mo and showed that the argument which led Zener and LeClair to favor a ring mechanism was not incompatible with a vacancy mechanism. In spite of this, it seemed to the authors that further experimental tests should be made by studying the Kirkendall effect in body-centered-cubic systems that characteristically have small ion core repulsion, such as the alkali-metal systems. Since the ion core repulsion term constitutes the main part of the activation energy needed for the rotation of a ring, such a test should be the most critical of all. The system K-Rb was chosen for experimental study because these metals form a continuous series of solid solutions. Experimental Investigation Owing to the extremely active nature of these two metals, a brass dry box (18 x 11 x 10 in.) was built for making the diffusion couple. It had a big lucite window on top, two side ports through which neo-prene-rubber gloves were inserted, and another side port covered with an optically flat-glass window for microscopic examination of the sample. Inside the box there were a circulating fan driven with a rotating horse-shoe magnet located outside the box, a heater used to generate potassium vapor for getter-ing the box, and a cold trap for keeping the inside of the box cool. Chemically pure grade K and Rb were triple distilled before they were transferred in vacuum into cylindrical steel molds kept in pyrex-glass ampules, Fig. 1. The latter together with the tools needed for making the diffusion couple were put into the dry box. After the box was flushed with purified argon and gettered with potassium vapor, generated from a heated steel crucible inside the box, the glass ampules were broken and the mound on the top of the alkali-metal ingot was cut off with a razor blade to yield a flat surface. To make the diffusion couple, one K ingot and one Rb ingot were pushed out of the molds together with their steel supports by screwing a metal plunger into the bottom of each mold. They were then laid on a brass cradle inside the assembling carriage (shown separately in Fig. 2) with the flat faces opposite to each

Jan 1, 1959

By Charles L. Mantell, B. G. Shah

SINCE the beginning of the industry, commercial electrolytic manganese has followed the Shelton patent' among others, which called for the addition of sulfur dioxide in controlled amounts, to a purified manganese sulfate-ammonium sulfate at a controlled pH. Every attempt to eliminate sulfur dioxide additions has resulted in operating difficulties, chiefly solution of the deposited metal and lowered current efficiencies. Many replacements for sulfur dioxide have been proposed and studied, chiefly sulfur compounds, urea, thiourea, and proteins similar to those employed successfully in copper refining. It has been suggested that sulfur dioxide is a re-ductant for higher-valence manganese compounds, or that it is reduced by manganese metal in the deposit to hyposulfites or its compounds, and that these might affect the cathode film or the deposition potential, or the overvoltage of manganese. The additives were studied following the method of Mantel1 and Ferment2 who determined the feasibility of current-potential curves as an analytical tool for monitoring manganese elec trowinning solutions for metallic impurities: nickel, cobalt, silver, copper, zinc, molybdenum, cadmium, magnesium, and sodium. The individual effect of each on the standard polarization was determined for a range of concentrations. Not all affected the polarization curve; cadmium, magnesium, and sodium had no effect. Nickel, cobalt, silver, copper, and zinc yielded a correlation between transition current and concentration of impurity.

Jan 1, 1968

By K. E. Manchester, A. H. Clark

Hall measurements have been made on three groups of silicon samples, which were implanted with boron, aluininunz, and phosphorus ions. Boron and phosphorus implants show essentially bulk properties when annealed under previously determined conditions, i.e., 15 min at 80O°C for boron and 10 mirz at 600°C for phosphorus. Bulk properties were also observed in alu?rrilzum-implanted samples when ion concentrations were below 1015 cm-'; however, strange low- terrzperalure behavior and a falloff in cavrier concenlralion was observed for sarnples with ion concenlration abozle loL5 ern-'. This can be attributed to solid-solubility effects since the average bulk concentration f0.r the sample exhibiting bulk properties was below the reported solubility limit for aluminum, while the other samples were above the limit. A detailed study of the annealirzg process indicates that mobilities reach bulk c~alues in phosphorus implants at 250DC, in alutninurn ivnplanls a1 500°C, and in boron implants at 700°C. A simple rnodel has been proposed to fit the annealing data. THE technique of semiconductor doping by direct injection of energetic ions is being actively investigated at this Center. Previously published results from this laboratory have been concerned with the investigation of implanted profiles in silicon and the electrical properties of the resultant p-n structures.1'2 Diode properties have been reported for junctions produced by implantation of boron ions and aluminum ions in n-type silicon and phosphorus ions in p-type silicon. Reverse current characteristics, as well as electron diffraction data, have indicated that the damage to the structure produced by the energetic ions during the stopping process can be minimized by a gentle anneal. The time-temperature conditions for this process have been determined by sheet resistivity studies.3 Electrical profiles of implanted phosphorus ions which have been determined by a differential sheet conductivity technique are based on the assumption that the carrier mobilities and activation energies for ionization are the same as in bulk silicon. These assumptions have been substantiated experimentally by measurement of Hall constants and resistivities of these implanted structures and the results are presented herein. After establishing the bulk property equivalence of the annealed layers, a more detailed examination of the annealing process was undertaken. The sheet resistivity technique initially used to determine anneal conditions has been broadened to include Hall constants and mobility behavior with anneal conditions. PROCEDURE The three groups of samples prepared for Hall measurements were implanted with mass-separated beams of boron, aluminum, and phosphorus ions. Ion concentrations are equivalent surface concentration and they have been determined from beam current measurements during implantation. Implant conditions for the samples are shown in Table I. In all cases, the samples had previously been angle-lapped on one edge and the junction delineated with an HF-copper sulfate solution. The surfaces of the implanted regions of the samples were exposed to the delineating solution and in the case of the "n"-type phosphorus-implanted areas it was later discovered that a finite amount of surface could be etched by this solution. This is discussed in the section on results. The implanted samples were ultrasonically cut into the conventional six-probe configuration shown in Fig. l.* In the annealing studies, for which the meas- urements were taken at room temperature, the sample holder was a Bakelite jig incorporating tungsten mechanical probes. The other measurements were taken using a conventional liquid-nitrogen cryostat, in which the temperature could be varied from 77" to about 400°K. For these measurements, 10-mil aluminum dots were evaporated onto the samples and alloyed with the silicon at 530°C for 15 min. The samples were then mounted in flat-packs, and gold wires were bonded to the aluminum dots. The electrical measurements were made with either a Leeds & Northrup K-5 Potentiometer, a Keithley 147 Nanovolt Null Detector, or a Keithley 601 Electrometer. No external bias was applied to the substrate. There is an inherent self-biasing arrangement at one or the other of the current contacts (depending upon the polarity), and this suffices to limit the current flow to the implanted layer. The magnetic field was generated by an A. D. Little electromagnet. Except for occasional checks of linearity of the Hall voltage with

Jan 1, 1969

By A. F. Meston

Centrifugal force has been used for centuries for separating liquids but machines for doing this are a comparatively recent development. The use of these machines is being extended into many industries but this paper is confined to their use in the oil industry. The centrifugal machine is found at the well where "cut oil" is dehydrated for acceptance by pipe lines; and in the refinery and byproduct plant. In fact, wherever finely divided suspended particles should be removed from an oil, there is a possible use for a centrifugal machine, if the particles have, or can be made to have, a specific gravity different from that of the oil. Centrifugal machines are also used for cleaning fuel and lubricating oils and dehydrating transformer oils. Applications and Results When oil comes from the well mixed with water, it is spoken of as cut oil. Settling often does not remove sufficient water for the oil to be accepted by pipe lines, thus necessitating chemical or other treatment. Centrifuging alone, or following chemical treatment, effectively prepares such oil for pipe lines, as is shown by the following data: WateR, Etc. Wat~R. Etc. Temperature, Oil to Pipe Line, aT StUt at Finish Degrees F. Bel. Per HouR PIE Cent. PEECent Oklahoma lease.... 160 10 10 0.25 Kansas lease....... 125 4 20 0.25 to 2 On the Oklahoma lease, the machine was cleaned of solid material once in 12 hr. At first, it was thought that chemical treatment was necessary to start separation and 1 qt. of prepared compound was added to each 100 bbl. of the cut oil before centrifuging. Later it was found that

Jan 1, 1924

By Howard C. Dunkle

Various factors can affect the quality of B1112 and B1113 steel as produced in a bessemer plant; among them: vessel-charging practice, blowing practice, ingot-pouring practice, ingot delivery-time practice, pit-heating practices, and ingot-rolling practice. Evaluation of the influence of ingot delivery time on quality has been chosen as the subject for this paper because this time is completely within the control of the operator, and on this particular factor there is a tremendous amount of information in the dusty archives of the average steel plant. In order to know how much improvement can be made and when attention should be directed to other factors that influence quality, in the continual struggle for improvement, the effect of ingot delivery time must be accurately evaluated. Once this is done, the importance of other variables can be accurately obtained, thus eliminating the necessity of resorting to opinions that are of doubtful value at best. In the study described herein, extensive use was made of the statistical card system as a method of determining the effect of ingot delivery time as a quality factor in bessemer screw-stock grades by simple direct correlation. The value of this statistical method as a means of accurately determining the influence of various factors has been amply demonstrated by Work1 for the bessemer process and by Hand and Gould2 and Fetters and Chipman3 for the open-hearth process. The quality records of 300,000 tons of bessemer screw-stock billets were used in this study of the effect of ingot delivery time on the rejections for breaks, pipe, check and seams. The reduction in the number of rejections for poor quality reduces the costs and increases the productivity per man-hour. The operator today, more than ever before, must know how to keep costs down, how to do it most quickly and in the best way, and how to obtain the highest quality in line with the ever increasing demands of the customer. It is necessary for him to know the individual relations and interrelations between various factors affecting the quality of the manufactured product if he is to produce material that will meet competitively the cost, performance, and quality demands of the trade. SIGNIFICANCE OF STEEL MANGANESE, MIXER SILICON AND STEEL SULPHUR AS QUALITY FACTORS In order to obtain the highest grade of material it is necessary to control many factors-not just one or two, as operators

Jan 1, 1945

By T. E. Tietz, J. E. Dorn

Activation energies for creep of copper at intermediate temperatures, where crystal recovery was negligible, were determined by the simple technique of rapidly alternating the test temperature between and T2 (T2 = TI + about 10°K) throughout a constant stress creep test. The activation energy for creep H was found to be 37,000± 3,000 cal per mol, independent of stress and strain. The same creep laws as have been previously established for high temperature creep were found to be valid for creep at intermediate temperatures. But the AH was found to be lower than that for self-diffusion in the intermediate temperature range whereas it is known to be equal to that for self-diffusion at high temperatures. IT is now well established that creep at high temperatures can be correlated by the functional relationship'-" e = f(?) s = constant [I] where E is the total plastic strain, f is the function that depends on the stress, ? = f e -- dt, t is the duration of test, e is the base of natural logarithms, AH is the activation energy for creep, R is the gas constant,T is the absolute temperature, and s is the stress. Thus, identical values of are achieved during creep under a given stress at two alternate temperatures at the same total strain. At the same strain therefore where subscripts refer to the two alternate temperature conditions of test. Consequently, the activation energy for high temperature creep is readily obtained with the aid of Eq. 2. Activation energies so obtained have been observed to be insensitive to the creep strain at which they are evaluated, the applied stress, grain size, minor alloying additions,'-' cold worked state, and the presence of thermally stable dispersions of intermetallic compounds in an a solid solution matrix Furthermore, the activation energy for high temperature creep is very nearly equal to that for self-diffusion in all cases where adequate data are available for comparison." " The apparent identity of the activation energies for high temperature creep and self-diffusion strongly suggest that high temperature creep arises from a dislocation climb process. This hypothesis is further strengthened by the fact that the energy of activation for high temperature creep is insensitive to the applied stress," and by the observations that the correlation suggested by Eq. 1 cannot be ex- tended to temperatures below those for rapid crystal recovery. When using the activation energy for self-diffusion, Eq. 1 fails to give the required correlations between creep curves at various intermediate temperatures.' This suggests that the dislocation climb mechanism for creep might be superseded by some alternate mechanism in the intermediate range of temperatures. This investigation was initiated in a preliminary attempt to ascertain the type of creep law that might be valid in the intermediate range of temperatures. Special consideration, however, was given to the determination of the activation energy for creep in this range because the Becker-Orowan', " and the Mott-Nabarro10 theories for transient creep suggest that the activation energy should increase

Jan 1, 1957

By Philip Bucky

THE general conception of a mine model is that of a three-dimensional object representing the mine workings, the orebody and the country rock of a particular property. Its chief uses have been to make it easier to understand the mine and to serve as a basis for the arguing of legal questions. Fayol endeavored to use mine models in a different way and to all students of subsidence "Fayol's dome theory" is of decided interest. We have more recently the suggestion of Young and Stoek of the University of Illinois, who1 suggest the use of models as a means of studying the problem. Prof. Henry Briggs, of the University of Edinburgh and Herriott Watt College, also makes use of models to determine the effects of bending at the edges of extensive workings.2 It is interesting to note that civil engineers are taking a decided interest in the application of models and the principles of dynamic similarity to the solution of their problems. The Proceedings of the American Society of Civil Engineers for 1930 contain an elaborate article by Benjamin F. Groat,3 who says, in his opening remarks: "Every engineer should know and understand that a model constructed in accordance with Newton's theory of similarity is not only the means for reproducing the complexities of flow, or other mechanical action, on a small scale, but that models may be made the best means of designing works of great magnitude. In the present state of knowledge, a properly constructed and properly tested model will answer the difficult questions of hydrodynamics much more quickly and accurately than the most profound mathematical analyses." A study of P. W. Bridgman's book on Dimensional Analyses leads one to arrive at the same conclusion.

Jan 1, 1931

By Ernest Klepetko

A NOTABLE amount of fossil resin exists in many of the bituminous coal beds of Utah. The upper part of these show a marked concentration of resin, which occurs primarily in the fracture seams. In general, these seams are less than 1/8 in. thick, but it is not uncommon to find coal with areas as thick as 3/8inches. The resin is of the hard kauri variety, with coloration varying from deep blood red to lemon yellow and almost colorless. There is also an almost black variety, which is not readily soluble in the same solvents as the lighter colored resins. These resins are valuable for many industrial purposes. When refined, they are suitable for uses similar to those for which lac resins are usually employed. They are particularly desirable for preparing dielectric varnishes. They are also desirable in preparing printing inks, waterproofing agents, special synthetic rubbers and rubber cements. They are especially suitable as an admixture in synthetic rubbers and cements, as they supply the essential tackiness the synthetics lack. The following chemical trade characteristics have been found by Inter-Chemical Co. research chemists in the refined resins: [Specific gravity (melted) 1.03 -1. o6 Acid number6-8 Softening point, mercury method 160 -165°C Iodine value (Wijs)140-1.50 Refractive index1.544 Color (Hellige, 25 pct toluol) ...14 Molecular weight, average732 Purity, 99 + pct pure hydrocar Bon] "Unaffected by alkalies and resistant to one hour fusion with solid potassium hydroxide. Completely soluble in aliphatic and aromatic hydrocarbons. Insoluble in alcohols, ethyl acetate and other commonly used alcohols and esters. Compatible with natural and synthetic rubbers, chlorinated and cyclized rubbers, waxes, vegetable oils, mineral oils, rosin, ester gum, phenolic and modified phenolic resins and other natural and synthetic resins of like solvent solubility. The recovery and refining of these fossil resins has been the subject of much research work and has intrigued many investigators. Broadly speaking, the problem involves separation of the resin from the coal into a very high-grade concentrate, and subsequent treatment of this concentrate to produce an acceptable refined resin for its various usages. Obviously it is also desirable to recover the residual coal without excessive size degradation. The late W. D. Green, concentration engineer for Combined Metals Reduction Co., obtained U. S. Patent No. 1773997 for the recovery of resin from coal through

Jan 1, 1947

"The earth is the Lord's and the fullness thereof." Science knows no national boundaries, knows no country. These views might be taken as premises for a discussion of the development of the mineral resources of the world. Yet how far man is removed from such broadminded ideals! In this day of jealousy and dread, of political machinations and statesmen's maneuverings, of rantings and crass ravings against fellow-beings, man's attitudes towards God's gifts are but the measure of the smallness of man. That the exploitation of mineral wealth should be for the common good, none will deny, but what is meant by "common"? Is it for the common good of The Pennsylvania State College, Pennsylvania, the United States of America, or the world? If man is big enough and honest enough to state categorically that by "common," as used in the context above, is meant that the utilization of the mineral wealth should be for the mutual benefit of all mankind, and that all concerned strive to see that such a viewpoint is executed, then there is brighter hope for the future. It is to be hoped that the world may have at least a few years or possibly a generation of peace. What can be done in these years to work towards the ultimate goal of human improvement? The work of statesmen in the drafting of international agreements and the easing of small frictions which appear between nations, as they

Jan 1, 1950

By J. V. N. Dorr

DEADWOOD and the Black Hills were familiar names to me from childhood, for. I had an uncle who was among the earliest eastern investors there and I used to hear of the Uncle Sam mine and its rich ore back in the eighties. The spring of my junior year at college, in 1893, brought me an offer of summer work at the Deadwood & Delaware smelter, in Deadwood, and full of the thrill of the long journey from New Jersey, I went out as chemist and stayed four months. Within a week or two of my arrival, I went through the tragic experience of seeing an associate drink cyanide by mistake and die within a few moments. I shall never forget the horror of feeling that my lack of knowledge of an antidote might be responsible for his death, but I found later that the solution he drank was so strong that nothing could have been done. A year after graduation, when I had settled down to chemical research work in New York, an offer came to go back to the smelter in Deadwood, and within a few days I was again tramping down "the Gulch" with my lunch bucket and putting in the standard assay office shift of that day, from 7 a.m. to 6 p.m., with a half-day off on Sundays. During my absence East, the D. & D. smelter had been changed from a pyritic smelter, using native pyrite, and Homestake concentrate to matte the siliceous gold ores, into a copper-matting smelter using copper ores brought from Butte, over the newly-completed Burlington rail-road. The work was interesting, and the laboratory offered many opportunities for making improvements. I remember also undertaking experiments at home on a new method of gold precipitation for the chlorination process and leasing a mine in Strawberry Gulch that promised great things, but soon petered out.

Jan 8, 1927

By Henry A. Ley

Oklahoma produced about 40,000,000 bbl. less crude oil in 1930 than it did in 1929, but developed the largest initial production from current well completions ever recorded in its history. The output of this year would have exceeded all previous years had it not been for state-wide production curtailment. The record initial production of 5,911,982 bbl. from new oil wells completed during the year is accounted for entirely by the rapid development of the Oklahoma City field. Completions declined to the lowest levels since 1909, as a result of a marked reduction in number of dry holes incident to reduced wildcat exploration. Leasing was most active in western and northern counties of the state west of Oklahoma City, but on a much smaller scale than in the preceding year. Geological and geophysical surveys were likewise most active in this western territory. The urge to deeper objectives resulted in the discovery of oil on the Cement fold. Changing economic conditions have created a distress situation among the marginal operators in northeastern localities of the state. Elsewhere in the state production records and successful exploitation of new supplies have been eclipsed by a new social concept of the industry in accord with natural economic developments. Many of the producers of crude oil have organized for a voluntary stabilization of the industry by regulating the output of wells. To enforce their measures these operators have sought for and secured the support of the state. Consequently, the current position of the crude-oil producer is not unlike that of the natural-gas producer—withdrawal of supplies in accordance with market needs. And while the industry as a whole is artificially stabilized by these measures individual operators and some of the integrated concerns suffer hardships. Oil Developments and Production The early operations in Oklahoma were confined to northeastern and eastern localities, beginning in 1885. The first commercial oil wells were completed in 1894, near Chelsea in Craig County, from Cherokee sands in the lower portion of the Pennsylvanian section. Scattered

Jan 1, 1931

By J. J. Bodmer

The substances or materials employed in this manufacture, are the same as those used in the preparation of mortar and concrete, viz., the different kinds of lime and sand. Instead of, or in conjunction with, sand there may be used calcined clay, blast-furnace slag, clinkers or ashes from furnaces, natural puzzolana, powdered chippings from stone quarries, etc. Of the different kinds of sand, pitsand—siliceous sand, as it commonly occurs mixed with gravel—and the sand found on the seashore, where the salt has been washed out by long exposure, whilst out of reach of the tide, may be used. The purer the above-named materials are from admixtures of clay, earth, or organic substances, the more complete will be their combination with the lime, the quicker will the manufactured brick or block set, and the more satisfactory will be the quality which it ultimately attains. For this reason, subdivided blast-furnace slag is preferable in most cases to sand, and the only sand which, in reference to setting capacity, is analogous to blast-furnace slag, is the volcanic sand occurring in different localities in North and South Wales, as an almost pure calcined silica. The lime used for the manufacture may be either slaked or unslaked. In the first case, (slaked), in order. to obtain satisfactory results, the lime must be strongly hydraulic. The use of unslaked lime, however, is by far preferable. A process for using fresh or unslaked lime has been patented in England by Major-General Scott. Lime thus prepared is called " selenitic lime," and consists of a mixture of fresh (unslaked) lime with sulphate of lime, or plaster of Paris. The graystone lime, for instance, found by the Medway, is mixed with from 5 to 7 per cent. of plaster, which has the effect of keeping the lime from slaking when water is added. This mixture also partakes of the nature of cement, and when used for mortar, or concrete, attains in a shorter time a greater degree of hardness than the same lime would ever have obtained after being slaked. Bodmer's process for the manufacture of artificial stone bricks consists chiefly in the use of automatic measuring, forwarding, and mixing apparatus, by means of which the materials are supplied and unite in a continuous stream, and are accurately measured. They

By George F. Weaton, Eugene P. Pfleider

13.4-1. History. During the past ten years the mining and production of iron ores has been through a revolution. From 1939 through 1948, which included World War II, 561,000,000 tons of iron ore was mined and shipped from Minnesota's Mesabi Range to the blast furnaces of the United States for the production of iron and steel products (20, 28, 29). The iron mining industry, anticipating the exhaustion of this highly productive source of raw material, instigated a worldwide search for new sources of iron ores. This search was highly successful, both as to quantity and quality. Venezuela (38), Canada (17, 28, 42), Peru (19, 23, 50, 52, 54, 56) Chile, (1, 66, 75), Brazil, and Liberia were among the countries where enormous deposits of high quality iron ores were discovered. The exploitation of these deposits took away the monopoly held by the Lake Superior region for so many years and created a highly competitive market for high quality natural iron ores. 13.4-2. Exploration and Development Practices. SPECIFIC TO IRON MIN- ING. American industries are motivated to continue exploration because new ore discoveries often lead to an improved competitive position with respect to raw material supply. Exploration techniques have advanced rapidly in recent years, to a degree that potentially important iron ore reserves, stratigically located, may now be detectable by application of a combination of refined and diversified geophysical exploration methods. Since the days of the dip needle, iron ore people have placed greatest reliance on the magnetometer. Its successive stages of development progressed from the balance and the torsion type to the fluxgate, and then to the "sophisticated" magnetometers-conceived and developed in th field of atomic physics. By far the greatest advancement in magnetometer prospecting was made when the self-orienting fluxgate magnetometer took to the air. This was not a new development, but it was a breakthrough in reconnaissance investi-

Jan 1, 1968