Search Documents

By John L. Lamont, Walter Crafts

An investigation has been made of the multiplying factors for some of the more common alloying and deoxidizing elements for use in calculating hardenability of steel according to Grossmann's method. The factors for manganese, silicon, and aluminum that were reported in an earlier communication2 have been confirmed by microscopic determination of the half-martensite structure rather than on the basis of an empirically determined hardness corresponding to a half-martensite structure. Measurement of ideal critical diameter by microscopic examination was found to be necessary for other alloying elements, and multiplying factors for nickel, chromium, molybdenum, zirconium, vanadium, titanium, and boron have been determined. The nature and order of magnitude of the multiplying factors reflect the effect of the alloying elements on the structural character of the steel. Except for nickel and vanadium, the multiplying factors agree fairly well with previously published results. Good correlation between actual and calculated ideal critical diameters has been found in developing the multiplying factors and in checking the results against fairly simple steels. However, some discrepancies have suggested the need for a more thorough study of low-carbon and complex steels. Testing Procedure The investigation was conducted principally on steels made at the Union Car- bide and Carbon Research Laboratories, Inc., in high-frequency induction furnaces using Armco iron and standard alloying materials. However, a few open-hearth steels were used in establishing the effect of nickel, and the hardenability factor for boron was based primarily on open-hearth steels. All bars were normalized prior to the machining of Jominy hardenability specimens. The Jominy test was carried out under conditions standard for the test.3 Austenitizing temperatures judged to be appropriate for the compositions of the steels were used. Chemical analysis was determined on a sample taken adjacent to the Jominy specimen. Residual amounts of phosphorus, sulphur, nickel, chromium, molybdenum, and copper were determined on only one heat of each group made with the same materials during the same period. "Acid-soluble" aluminum and zirconium rather than total amounts were determined, as it is considered probable that the acid-soluble amount is more representative of the effective alloy. As tin was present to the extent of only 0.002 per cent, its effect was neglected. The method used to determine boron in the steels shown in Table 9* was developed by Galen Porter, Vincent Napoleon, and Thomas R. Cunningham, of the Union Carbide and Carbon Research Laboratories, Inc., and is a modification of J. Naftel's procedure for boron in soils

Jan 1, 1944

By M. Gensamer

THE PURPOSE OF THIS PAPER is to lay a foundation of elementary theory that might be useful in the discussions which it is hoped will be evoked during this Symposium. It is not my purpose to try to expound the details of the most complete theories as that would be impossible in the time at our disposal and, even if time were available, would probably be of less usefulness than a discussion of the principles underlying the advanced theoretical treatment. I shall try to discuss the fundamental bases for these advanced theories. There exists at the present time very much less need for a detailed description of complete theory than existed when this Symposium was being organized. The reason for this is that a series of papers by L. R. Underwood has been appearing in the magazine Sheet Metal Industries. It is understood that this series will he published soon in the form of a book. Dr. Underwood's articles are complete, critical and well written and it would be hopeless to try to do better in less space. The need, then, is for a brief treatment of basic theory. The objective of any theory of plastic forming- is to enable one to calculate the force and power requirements for the process, and where the deformation is not uniform, to calculate the distribution of strains- In the formed object. We need as the basis for the calculation the relationship between stress and strain in the metal, particularly for the combination of stresses imposed by the forming process. We need to know the stress-strain curve for some simple state of stress, and we need in addition some theory

Jan 1, 1948

By J. M. Smith, D. Kunii

Effective thermal conductivities of sandstones filled with stagnant fluids were measured using a steady-state technique. Data were obtained for seven sandstone samples, taken from four different locations and ranging in permeability from 18 to 590 md. The measurements with gases (helium, nitrogen, air and carbon dioxide) covered a pressure range from 0.039 psia to 400 psig. Data were taken for four liquids — n-heptane, methyl alcohol, 79.8 weight per cent glycerol-water solution and pure water at atmospheric pressure. The experimental results were used to evaluate the theoretical equations for predicting stagnant conductivities developed earlier 4 The low-pressure measurements permitted evaluation of the consolidation parameter bpDp/ks (necessary to utilize the theory) for the various types of sandstones. Using these characteristic values, the tbeoretical equations correlated well with the experimental conductivity data for the several fluids and rock samples. INTRODUCTION An aspect of heat transfer in solid-fluid systems of considerable current interest is the effective thermal conductivity of porous media. The stimulus for study of the subject arises from the need for sound procedures for designing thermal methods of petroleum production. The general system occurs when there exists a flow of fluid through the pores of the solid material. However, a logical starting point in developing a theory for predicting the effective thermal conductivity in the general system is to attack the special case when the porous solid is filled with stagnant fluid. Since the flow rates anticipated in thermal production processes are very low, such stagnant conductivities k,O are also of practical significance. Kunii and Smith4 recently reviewed the existing data for stagnant conductivities and proposed a theory for heat transfer in porous rocks. This leads to equations for predicting the stagnant conductivity as a function of the properties of the fluid and solid phases. The existing experimental information1-3,5,7,8 covered a range of porosities and agreed well with the theory. However, the available data were insufficient to examine critically the effects of two important properties on koe, — the thermal conductivity of the fluid and the pressure. The objectives of the present study are twofold: (1) to measure the effect on koe of (a) the pressure for gases, and (L) the thermal conductivity of the fluid kg for bloth gases and liquids; and (2) to determine for rocks of different porosities and permeabilities the apparent solid conductivity ks and the consolidation parameter bpDp/ks required in applying the theoletical equations. Measurements extrapolated to zero pressure are helpful in evaluating ks and the consolidation parameter. However, the extrapolations must be based upon data obtained at low pressures because in small pores the molecular conductivity of the fluid may be unusually depressed. This occurs when the mean free path of the molecules is of the same order of magnitude as the pore diameter, that is, in small-diameter pores at low pressures. The phenomenon has been studied recently by Schotte6in beds of unconsolidated fine particles. With particles in the size range of 45 to 200 microns, a significant reduction of kg with pressure was found even at absolute pressures greater than 1 atm. In the sandstones employed in the present investigation, pore diameters lower than those experienced by Schotte are likely, so that the effect would presumably be greater. SCOPE OF MEASUREMENTS Stagnant conductivities were measured for four types of sandstones using a total of seven samples. The characteristics of the samples, including porosity and permeability values, are given in Table

By Karl Cohen

The question of attainment of competitive nuclear electric power is of interest to uranium producers because the rate of attainment of this goal determines the date when there will be a solid, non-political, domestic uranium market. It is a burning question to those of us in the civilian nuclear power business, because our entire business future hinges on how well, and how soon, we can make electricity from nuclear reactions at prices comparable to electricity from coal. For an idea of the magnitudes involved, consider that the first fuel load of the Dresden (Illinois) nuclear power station, plus spares, will be about 90 tons of 1.5 pct UO2. This requires about two-and- a-half times as much natural uranium oxide feed to the diffusion plant, or 225 tons. This, in turn, represents about a month's production from the nearby Uranium Reduction Co. mill. Note also that the 180,000 kw electric output of the Dresden station will be about 0.1 pct of the national electric generating capacity in 1960.

Jan 12, 1958

By Marlin J. Veesaert

Urban quarries offer one of the greatest opportunities for profit in nonmetallic mining with limited financial risk-if properly evaluated, planned and developed to meet market needs. Location, with respect to market, is the prime consideration. Geologic considerations and quality of rock are nearly as important. Cost factors and return on investment (ROI) are the principal financial considerations.

Jan 8, 1979

One of the newest and most modern surface mining operations in the East is gathering steam at Mapco Inc.'s Martiki mine in anticipation of yielding 2.7 million tons (3 million st) of coal annually.

Jan 10, 1977

By C. F. Willis

Many of the failures in vocational education are due to the fact that the educational methods were not designed to the capabilities, habits, and environments of those to be trained; rather they were based on the policy that education is education and lessons are lessons, whether for youngsters of fifteen or for men of forty. Vocational education among miners involves, first, a study of the men themselves, their habits, and the use of their leisure time; second, a study of the differences between the methods of teaching required for men and for children. Certain fundamental requirements of training methods for miners are reasonably universal and may be applied with success to any ordinary mining community. The rate of labor turnover is another consideration; it would be useless to design a four-year course for men who remain in one place only a few months. Length of Course The first consideration should be the length of the course. Few mining communities have a sufficiently stable population to make it possible successfully to carry on a course for over a year. While some men might complete a four-year course, the number is comparatively small compared with the number to whom a shorter course would be of service, and it is better to raise the standards of education even a little for a large number than to raise them to a high level for a few. It is perfectly possible to attain both objectives by arranging the courses in small units; all the units, when grouped together, should comprise a fairly complete course, yet any one unit should be complete in itself and of benefit to the workman. It should not take many of these units to make a miner or a timberman out of a mucker; but to do this the course should be short, because muckers seldom stay in one place long. By grouping a number of these units together it Would be possible for a miner to become a shift boss or a shift boss a foreman, and so on. As far as possible the units of the course should not be dependent on those preceding or following. The workman understands the completed job but he is not accustomed to carrying on several jobs at the same time and

Jan 1, 1920

By W. N. Lacey, R. H. Olds, B. H. Sage

The volumetric behavior of five mixtures of black oil and natural gas and of two mixtures of condensate and natural gas from a field in the San Joaquin Valley was experimentally established. This work was carried out at roo°, I9o° and 250°F in the pressure interval between 400 and 5000 psi. The viscosity of the liquid phase of four mixtures of black oil and natural gas was experimentally measured in the above-indicated temperature and pressure intervals. The effect of methane upon the precipitation of bitumen from the black oil was studied at 230°F. Introduction The solution of a number of the economical and technological problems which arise in connection with petroleum production is dependent upon the availability of the necessary quantitative information covering the materials involved. This requires data concerning physical properties of naturally occurring hydrocarbon mixtures at the pressures and temperatures characteristic of underground petroleum reservoirs. The experimental determination of the desired data for each situation encountered is relatively time-consuming. However, it is considered to yield results sufficiently more reliable than those obtained from correlations to justify the effort. For these reasons there was undertaken a laboratory investigation of the viscosity of the liquid phase and the volu- metric and phase behavior of mixtures of oil and gas samples obtained from wells in a field located in the San Joaquin Valley. Terminology The nomenclature of petroleum engineering is not at present entirely standardized. Many commonly used technical terms are not everywhere given the same meanings. For the purposes of this paper the following definitions will be adopted: Black oil refers to the dark-colored, hydrocarbon liquid obtained when the producing horizon of the well lies partly in the condensed hydrocarbon phase of the reservoir. Condensate is the term applied to the relatively volatile, pale yellow or amber-colored hydrocarbon liquid that is often obtained from the surface separator system when the producing horizon of the well lies in the gas cap of the reservoir. The gas obtained from the surface separator system is called natural gas regardless of whether the well is producing black oil or condensate. As might be expected from the multi-component character of naturally occurring hydrocarbon materials, the compositions of black oil, condensate and natural gas are subject to considerable variation depending upon the temperatures and pressures prevailing in the surface separator system as well as upon the overall composition of the material produced from the reservoir. In order to obtain samples capable of reproducing the total hydrocarbon material produced by the well, all oil and gas mixtures used in this investigation were com-

Jan 1, 1949

By Lars Rossemyr, Terkel Rosenqvist

The equilibrium Mn + 2 IiCl = MnCl2(g) + H2 has been studied at 1090°C for pure manganese and for Mn-Si alloys. For this reoction a standard free energy of Fo1363, = - 19,700 i 300 col ioas found. Combined with other thermal data, the standard free energy of the reaction Mn(s, ß) + Cl2 = MnCl2(g) was derived: Fo=- 56,140 + 9.78 T log T - 40.10 T For the formation of the various manganese silicides the following free energies were obtained. 5 Mn + 3 Si - M1z5Si3 ?F°1363 = -41,500 i 1500 cal Mn + Si - h.lnSi ?F°1363= -10,000 i 500 cnl Mn + 2 Si = MnSiz ?F°1363= -11,500 ± 500 cal In the search for a method suitable for the study of thermodynamic properties of certain alloy systems, it was found that the heterogeneous equilibrium between the alloy and a gas mixture consisting of hydrogen chloride, hydrogen, and volatile metal chlorides has considerable advantages. In addition to giving thermodynamic information about the alloys, such measurements may be used to derive thermodynamic data for the volatile metal chloride itself. The present paper gives some results which were obtained for manganese silicides and manganous chloride. Similar studies are presently being carried out for the iron silicides. The phase diagram of the Mn-Si system is rather well known,' but no information exists to the authors' knowledge about the thermodynamic properties of manganese silicides or about the chemical activities in molten Mn-Si alloys. At elevated temperature, manganese may react with hydrogen chloride according to the equation: Mn(s, ß ) + 2 HC1 = MnC1, (g ) + H2 [ 1] with the equilibrium constant The value of K, may be determined from measurements of the gas composition in equilibrium with pure manganese. When this value is used in connection with measurements on manganese alloys, the chemical activity of manganese in the alloy may be derived. Initial calculations showed that around 1000" to 1200°C the equilibrium constant K1 has a value of a few thousand, i.e., the reaction is shifted far to the right. In order to study this rather unbalanced gas composition, a flow method was used in two slightly different modifications. For all experiments with manganese silicides and for some experiments with pure manganese the apparatus shown on Fig. 1 was used. A bed of the metal or alloy was placed in a tube furnace. The refractory tube had an internal diameter of 14 mm and the bed was 75 mm long. Electrolytic manganese of high purity and silicon, 99.95 pct Si, were used as raw materials. All alloys were prepared by melting weighed amounts of the elements in a high frequency induction furnace in argon atmosphere. The melting was done in a silica crucible which was placed inside a graphite shell. The alloys were crushed to - 10 +40 mesh and analyzed chemically. Also, for the pure elements, the same size fraction was used. A controlled gas mixture of purified hydrogen and from 3 to 12 pct HC1 was passed through the bed where it reacted with manganese according to Eq. [I]. The volatile manganese chloride was collected in a condenser placed in the cooler part of the furnace tube. The gas mixture before and after the furnace was sampled and analyzed by absorption of

Jan 1, 1962

By Stanley D. Michaelson

The selection of the proper size of grinding mill for a given installation has long been a subject of discussion by mill manufacturers, consulting engineers, and their clients. It would be presumptuous for the author to propose a simple cure-all. Instead this paper describes a method that has been used over a period of years to determine mill size with a reasonable degree of accuracy. Furthermore, this method claims no theoretical background, for ball milling, as practiced today, is still an art. The selection of the proper size and type of mill must, therefore, be made on an empirical basis. A ball mill, in order to grind, must deliver power through its grinding media to the material to be ground. Assuming that a mill is properly supplied with grinding media, ore pulp, and power, the amount of grinding done is closely proportional to the power expended. With this as a basic premise we can, for the moment, forget about type of mill (i.e., overflow, low-level mill, or other design) and base our calculation of mill size on the total power required to grind a ton of a particular ore from a given size of feed to a given size of product. When this is determined the type and size of mill, its speed, and the weight of the load of grinding media can be selected to absorb this amount of power. Development of Technique Some years ago, W. L. Maxson, F. Cadena, and F. C. Bond, working in the Minerals Research Laboratory of Allis-Chalmers Co., Milwaukee, developed and described a laboratory technique for comparing grindability (or relative ease of grinding) of various ores at different mesh sizes of grind.' Additional papers2 have described the work done since that time, and the most recent paper3 summarizes results for hundreds of tests on many ores and materials. The essentials of the testing method are: a 12 by 12-in. laboratory mill operating at a constant speed of rotation, using a constant volume of ore, and a constant ball load having a relatively constant grinding surface. Tests are run at 250 per cent circulating load with the feed, circulating load and products screened on calibrated Tyler standard screens. Certain ores from operating mills, representing various mineralogical types, were selected for reference and designated "standard ores." In most cases, detailed studies of the grinding circuits were made when samples of mill feed were taken for grindability tests. Each analysis formed a basis for comparison of the grindability in the laboratory with actual power requirements for a particular grinding circuit. In addition, a critical study was made to evaluate the differences in the various grinding circuits so that two or more field installations having different layouts (single-stage grinding, two-stage grinding, or others), and using mills of various diameters operating at various speeds with differing circulating loads, etc., could be compared. Large-scale tests by mill operators complemented by laboratory investiga-

Jan 1, 1947

By Stanley D. Michaelson

The selection of the proper size of grinding mill for a given installation has long been a subject of discussion by mill manufacturers, consulting engineers, and their clients. It would be presumptuous for the author to propose a simple cure-all. Instead this paper describes a method that has been used over a period of years to determine mill size with a reasonable degree of accuracy. Furthermore, this method claims no theoretical background, for ball milling, as practiced today, is still an art. The selection of the proper size and type of mill must, therefore, be made on an empirical basis. A ball mill, in order to grind, must deliver power through its grinding media to the material to be ground. Assuming that a mill is properly supplied with grinding media, ore pulp, and power, the amount of grinding done is closely proportional to the power expended. With this as a basic premise we can, for the moment, forget about type of mill (i.e., overflow, low-level mill, or other design) and base our calculation of mill size on the total power required to grind a ton of a particular ore from a given size of feed to a given size of product. When this is determined the type and size of mill, its speed, and the weight of the load of grinding media can be selected to absorb this amount of power. Development of Technique Some years ago, W. L. Maxson, F. Cadena, and F. C. Bond, working in the Minerals Research Laboratory of Allis-Chalmers Co., Milwaukee, developed and described a laboratory technique for comparing grindability (or relative ease of grinding) of various ores at different mesh sizes of grind.' Additional papers2 have described the work done since that time, and the most recent paper3 summarizes results for hundreds of tests on many ores and materials. The essentials of the testing method are: a 12 by 12-in. laboratory mill operating at a constant speed of rotation, using a constant volume of ore, and a constant ball load having a relatively constant grinding surface. Tests are run at 250 per cent circulating load with the feed, circulating load and products screened on calibrated Tyler standard screens. Certain ores from operating mills, representing various mineralogical types, were selected for reference and designated "standard ores." In most cases, detailed studies of the grinding circuits were made when samples of mill feed were taken for grindability tests. Each analysis formed a basis for comparison of the grindability in the laboratory with actual power requirements for a particular grinding circuit. In addition, a critical study was made to evaluate the differences in the various grinding circuits so that two or more field installations having different layouts (single-stage grinding, two-stage grinding, or others), and using mills of various diameters operating at various speeds with differing circulating loads, etc., could be compared. Large-scale tests by mill operators complemented by laboratory investiga-

Jan 1, 1947

By Ronald Gibala

THE Au-Ni alloy system is one of many binary systems in which the supersaturated solid solutions may exhibit a multistaged precipitation behavior during aging. In addition to the equilibrium phase separation, which was studied extensively years ago in the range 400" to 600",' there exists at least one earlier stage of precipitation, i.e., preprecipitation, which occurs below 300°C in quenched alls.-This note reports on some effects of composition on the preprecipitation in Au-Ni alloys as determined from resistivity measurements. The kinetics of the preprecipitation were studied in alloys of 15 to 85 at. pct Ni which were water- were found in alloys which after various quenching-and-aging treatments were slowly heated and cooled (1Z"C per hr) between room temperature and about 300°C. Two such heating-cooling curves for a 40 pct Ni alloy are shown in Fig. 2. Similar effects were observed in other 15 to 50 pct Ni alloys. These curves are characterized upon heating by two changes in slope indicated by A and B in the figure and upon cooling by a resistivity hysteresis of approximately the size of the original decrease in resistivity after the aging treatment. The inflection at B generally falls at about the same temperature for all heating curves for a given alloy and appears to be a critical temperature (T,) for the preprecipitation for that alloy. The values of T, for most of the 15 to 50 pct Ni alloys fall in the range 200" to 220°C. The position of the inflection at A depends upon the heat treatment prior to the heating-cooling run and perhaps the heating rate, which was held constant in these runs. The preprecipitates grown in by the appropriate aging treatments seem to decrease in size as the alloys are heated from A to T,, dissolve at T,, and do not reappear after cooling below T,. When similar heating-cooling treatments were performed on 60 to 85 pct Ni alloys, an entirely different behavior was observed. Typical results are shown in Fig. 3 for an 85 pct Ni alloy. In these

Jan 1, 1964

By Paul Rhedey

Various commercial pelroleum cokes were heat-1,reated at temperatures between 500° and 1500°C, in a nitrogen atmosphere, in laboratovy induction furnaces. The rate of tenlperature rise was varied betzveen 10" and 300°C per min, or the green cokes were flash-calcined, orv a combination of heating rates was used. Changes in the rate of heating had only negligible effects on the degree of' calcination as characterized by mean crystallite thickness and the chemical properties of the calcined coke. The physical structure of the cake was however significantly affected when rate of heating during calcination exceeded 50°C per min over the temperature range of 600° to 900°C. Surface-accessible porosily increased with the .rate of temperature rise, and this was accompanied by a change in pore size distribution. Source and properties of the green coke also had an influence on the structure of the calcined coke. The evidence presented suggests a similar mechanism of porosity development in petroleuiiz coke during calcination in industvial equiplnenl, such as rotary kilns. An increase in surface accessible povosity incveased the pitch binder requirement when the coke was used as aggregate in Soderberg paste. A correlation was established between calcined coke porosity and paste binder requiremenl. ManY results have been published on the changes of properties of petroleum coke during calcination, such as chemical composition, real density, electrical resistivity, crystallite and pore structure. The correlation of these properties with temperature of calcination and time at maximum temperature has been rather well established in both laboratory and pilot plant experiments. Surprisingly little attention has been given however to the effect of calcination conditions, such as rate of temperature rise or furnace atmosphere, on the chemical and structural properties of the calcined coke. It has been observed that petroleum coke, when calcined in industrial equipment, acquires higher porosity and lower real density than those attainable in laboratory furnaces at apparently identical calcina- tion temperature and soaking time. This paper describes a study of the effect of rate of heating during calcination on calcined coke properties using green petroleum cokes of different volatile matter, hydrogen, and sulfur content. An attempt was made to correlate the changes in coke structure with the flowability of anode paste of the type normally used in aluminum reduction cells. EXPERIMENTAL Petroleum Cokes Used. In the study of release of volatile matter and sulfur during calcination and the effect of rate of heating on calcined coke properties two delayed cokes of different sulfur contents were used. The results of analysis of the green cokes are given in Table I. In the study of the effect of flash calcination thirty-six commercial petroleum cokes from twelve different refineries were used with a range of properties shown in Table 11. Calcination Conditions. Calcination experiments were carried out in a laboratory induction furnace. In each run a 200-g sample of dry green coke sized to 10 by 65 Tyler mesh was calcined in a graphite crucible. The crucible containing the sample was placed in the middle of a stack of eight others filled with metallurgical coke to reduce temperature gradients within the sample. Temperature was measured by two Pt, Pt-10 pct Rh thermocouples and controlled by a Celectray instrument. The two couples generally agreed within 5°C. In the study of volatile matter and sulfur release the samples were heated to temperatures in the range of 500" to 1500°C at a rate of 10°C per min in a nitrogen atmosphere and held at the final temperatures for 30 min. In the study of the effect of heating rate on calcined coke properties the desired rates between 10' and 300°C per min were obtained by manually adjusting the power input. Flash calcination was carried out by dropping 100 g of the green coke into the graphite dish preheated to the calcination temperature. Because of the small heat capacity of the furnace the coke was introduced in 20-g portions at a time. For this purpose a 2-in.-long nipple between two 1-in. gate valves installed on the top flange of the furnace served to provide a gas seal while feeding coke to the furnace. It was estimated that the temperature of the coke reached that of the furnace at a rate of approximately 1000°C per min. Holding time at final temperature was also 30 min. Calcined Coke Proper- Determined. Porosity was determined on 20 by 35 Tyler mesh samples using an Aminco-Winslow mercury pressure porosimeter with an operating range of 1.8 to 3000 psi absolute pressure (100 to 0.05 p pore diameter range).' Apparent density was obtained by the mercury poro-simeter. It represents a particle density of the 20 by

Jan 1, 1968

By L. W. Holm

Laboratory flooding experiments on linear flow systerns indicated that high oil displacement, approaching that obtained from completely miscible solvents, can be attained by injecting a small slug of carbon dioxide into a reservoir and driving it with plain or carbonated water. Data are presented in this paper which show the results of laboratory work designed to evaluate this oil recovery process, particularly at reservoir temperatures above 100°F and in the pressure range of 600 to 2,600 psi. Under these conditions CO2 exists as a dense single-phase fluid. It was found that a bank, rich in light hydrocarbons, was formed at the leading edge of the CO? slug during floods on long cores. Formation of this bank is probably due to a selective extraction by the C02 and, it is believed, partially accounts for the attractively high oil recoveries. In crddition to the efficient displacernerlt of oil from the pores of the rock by this process, the favorable rnobility ratio related to a C0 2-water flood also contributes to high oil recovery. A further advantage of this process is noted on limestone and dolomite rock, in that the CO1 reacts with the porous medium increasing its permeability. Flooding experiments were conducted on sandstone and vugular dolomite models. The results of this experimental work show the effect on oil recovery of type of porous medium, pore geometry, flooding length, and flooding pressure. The porosity of the cores and rilodels varied from 16 to 21 per cent and their pern~eabilities ranged from 100 to 200 md. A reconstituted West Texas reservoir oil, a West Texas stock tank oil, an East Texas stock tank oil and Soltrol were used to represent reservoir oils in this study. Oil recoveries ranging from 60 to 80 per cent of the original oil in place in these cores were obtained by CO2,-carbonated water floods at pressures between 900 and 1,800 psi, compared with conventional solution gas drive and water-flood recoveries of 30 to 45 per cent on the same cores. Oil recoveries greater than 80 per cent resulted frorn f1oods at pressures above about 1.800 psi. There high recoveries were noted from both the sandstone and the irregular Porosity carbonate cores. In all floods, additional oil was recovered by a solutiorr gas drive resulting from blowdown following the flood. Oil recoveries of 6 to 15 per cent of the original oil in place were obtained during this blowdown period. This additional recovery was found to be a function of oil remaining after the flood, decreasing with decreasing oil saturation. It was also noted that highest oil recoveries by blowdown were obtained when carborlated water rather than plain water followed the CO, slug. INTRODUCTION Miscible phase or solvent flooding processes, which are designed to increase oil recovery -from petroleum reservoirs, involve the injection of small quantities of a petroleum solvent into the reservoir, followed by an inexpensive scavenging fluid which is miscible with the solvent. Essentially complete displacement of oil from the pores of reservoir rock has been obtained by this technique. CO,, although not completely miscible with most reservoir oils at moderate pressures, is highly soluble in these oils at pressures above about 700 psi; there is appreciable swelling and reduction in the viscosity of oil when CO, is dissolved in it. Therefore, CO, could be expected to perform similarly to other oil solvents as a displacing agent. CO, is also highly soluble in water at elevated pressures, so water should be a satisfactory material to drive a slug of CO, through an oil-bearing reservoir. A favorable mobility ratio would be obtained through the reduction in viscosity of the oil and the use of water as a final displacing agent. A number of investigations of the use of CO, to improve oil recovery have been reported in the literature.2,3,4,5,6 These studies, however, have been conducted on uniform porosity sandstone at relatively low temperatures and pressures. The behavior of CO1 as a flooding agent at temperatures above its critical temperature could not be predicted adequately from these studies, particularly for the case of non-homogeneous rock. The purpose of this work was to evaluate the oil recovery efficiency of a process involving the injection of a CO2 slug followed by carbonated water, at reservoir temperatures above 100°F and in the pressure range of 600 to 2,600 psi, and to compare this process with conventional water flooding. The investigations were primarily designed to provide information on the efficiency of the process in irregular porosity carbonate rock. The effects of flooding path length, the presence of free gas, the type of oil to be recovered, and the amount of solvent required were also determined. The essential results of static phase behavior studies and experimen-

In the history of American mining, so far as I know, there is no cleaner, brighter, or more completely successful mining adventure than that of the United Verde Extension.* It deserves to be placed on record here. The mine is at Jerome, 25 miles northeast of Prescott, in Yavapai county, Arizona. For 30 years before the U.V.X., as it is known to mining men, achieved celebrity, the Jerome district was identified with a copper mine, the United Verde, one of the great mines of the world. The success of this mine, of course, stimulated the search for similar orebodies, or for an extension of those already known, in adjacent ground; but, despite vigorous prospecting, the United Verde remained for many years alone in its glory. The reason for this solitariness was geologic: a fault with a big throw frustrated the effort to trace the ore-zone, thereby causing exploratory work to be both uncertain and costly. Despite these failures to develop other mines in the vicinity, the belief persisted that all the ore was not localized in the United Verde mine, but before we consider the reasons for such a belief we must look at the geologic conditions. The basal rock of the Jerome district is a schist, which has been correlated with the Yavapai formation of the Bradshaw quadrangle. This schist is geologically ancient, for it is of pre-Cambrian age. It is composed of volcanic tuffs, together with sediments, both argillaceous and siliceous, all of which

Jan 1, 1932

By S. D. Dahlgren

The plasticity of unalloyed P plutonium was studied by evaluating the strain-rate-hardening exponent, m, in the equation Values of m up to 0.33 and tensile elongations up to 680 pct were obtained for ß plutonium formed directly from the a phase. Casl bars that were cycled and tested had lower flow stresses and higher values for than uncycled bars , hut their total plastic elongations were not as great as expected because of premature failure at voids formed during cycling. Flow stresses were higher and m was lower (m = 0.15) for 9 plutonzutn formed from the y phase. ThE strain-rate-hardening exponent for plastic flow of p plutonium was determined as a function of strain rate, test temperature, and heat-treating history, and it was related to the rather large plastic elongation found previously for some plutonium tensile samples. Gardner and ~ann' obtained tensile elongations of up to 620 pct for P plutonium samples which had been completely transformed from the low-temperature a phase to the P phase before testing. Such a large percentage elongation is unusual for unalloyed metals or single-phase alloys.' The a phase is stable below approximately 112°C and (3 is stable between approximately 112" and 190"c.~ Both phases have mono-clinic structures. A temperature of 160°C is 0.58 of the effective absolute melting point, 475°C) of the p phase. The effective melting point is obtained by considering the enthalpy and entropy changes associated with the higher-temperature phase transformations and it is not the same as the experimental melting point of the highest-temperature allotrope of unalloyed plutonium. Nelson, Bowman, and Bierlein observed a striking difference between the ductility, as well as other mechanical properties, of p plutonium formed from the next higher-temperature phase (y) and the ductility of /3 plutonium formed from the a phase. The total elongation of /3 plutonium formed from the y phase was less than 5 pct. Earlier, the creep rate of 13 plutonium formed from the a phase was shown to be 200 to 500 times faster than the rate for 0 formed from y for the same test temperature and stress.

Jan 1, 1969

By Arthur Fleischer

The Kalunite process+ for the production of metal-grade alumina from alumina-con-taining ores is applicable, considered from a general point of view, to any aluminous raw material that can be converted to potassium alum or equivalent normal alum. This result of modern technology has been the subject of a continuous study and development since 1929, on a laboratory and test-plant scale, with initial emphasis on the utilization of alunite as the raw material. The research and developmental program was carried out by the Kalunite Company and its successor, Kalunite, Inc., an affiliate of the Olin Corporation of East Alton, Illinois. The process is now approaching the time for a major test in its history with the completion of construction of a plant having a capacity of IOO tons of alumina per day in Salt Lake City for the conversion of Marysvale, Utah, alunite ores to alumina and potassium sulphate. The Salt Lake Alumina Plant is a Defense Plant Corporation project. Production of Aluminum: The known existence of alunite deposits, especially in the Marysvale district, furnished the motive for the original inquiry into the utilization of this raw material for aluminum production. The deposits in this region were actively explored during World War I and utilized for the production of potassium sulphate, an essential fertilizer, of which a shortage of monumental proportions then existed. Up to the twentieth century—for alunite is a mineral with an ancient history—it was used in Europe and in China as a source of potassium alum. It never had been used successfully in this country as a source of oxide for reduction to metal. Although the known reserves of this ore, which undoubtedly will be greatly expanded with a commercial outlet for this ore, are recognized to be sufficient for only a part of the present-day needs of aluminum, it has a definite place in the aluminum industry. Academically it points the way for future raw materials. The aluminum industry has undergone a remarkable growth in the past few years as a result of defense and war requirements. Its expansion in many ways has been beyond belief and prediction, both in volume and location. This wartime status of the industry has accelerated the consumption of bauxite to such an extent that a re-evaluation of the raw material reserves for the future peacetime industry and for eventual wartime reserves is seemingly of concern. The generally accepted picture of bauxite ore reserves in the United States, especially in raw material suitable for treatment by the Bayer process, focuses attention on other possible sources of raw material of metal-grade oxide. The perspective for the development of a suitable process may have changed in the interim since the original work by Kalunite, but the ultimate goal is the same.

Jan 1, 1944

By L. G. Jones

The objective of this paper is to present a better method for determining reservoir reserves of gas from extended drawdown test data. Means are proposed for conducting the test with or without the requirement of prior build-up to a static reservoir pressure. The test is based upon solutions to unsteady-state gas flow developed in an earlier paper and is believed to be superior to previous methods for determining reserves from flow-test data. The limitatiom of such tests are discussed, with emphasis on the subject of test duration. The test can supply useful information if the mechanics and limitations of it are understood. This type of information can be particularly valuable in deciding whether or not to drill offsets to producing wells. INTRODUCTION In the life of any gas or oil field, the engineer in charge must decide if certain wells need stimulation and whether or not to drill more wells in the field. Well production tests can aid in making these decisions. For instance, the value of stimulation can be estimated by determining formation permeability and the amount of well damage from drawdown or build-up tests. These tests are freely used in the oil industry. A less well-known type of analysis uses data from extended drawdown tests for determining reservoir reserves. Into this category fits the "reservoir limit test" of Jones,'-3 and the "reservoir reserve test" presented in this paper. The chief value of these tests is their ability to "see" reservoir boundaries and thus prevent costly dry holes. Methods for determining reserves of both gas and oil reservoirs were proposed in the work of Jones. His proposals appear sound for single-phase liquid flow. The generality of his work on gas flow is open to question, however, since the analysis is based upon solutions to liquid-flow equations. The test for gas reserves presented here is derived from unsteady-state gas-flow solutions presented in a previous paper.' In deriving this reservoir reserve test, it has been assumed that all of the reservoir energy is provided by expansion of the reservoir fluid and that the reservoir is radially symmetrical. No mention has been made of the effects of deviations from Darcy's law such as quadratic (turbulent) flow and well damage. Since the terms representing these effects are function of rate only, since the rate is constant and since the data are plotted in a differential form, it seems reasonable that these terms will not affect the test results in any way. No attempt has been made to estimate the effects of water drive, faults, or other departures from an idealized and isolated reservoir. For a qualitative discussion of some of these effects, the reader is referred to a paper by Jones3

By L. W. Pommier, F. B. Brien, A. K. Bhasin

The diflerential movement of solid particles through solid-liquid suspensions is very important to many branches of engineering. The flow of suspensions around immersed bodies is mainly of a turbulent nature. Problems are encountered when attempts are made, as is the general practice, to extrapolate the velocity and resistance relationships of Newton, pertaining to Newtonian systems, into non-Newtonian solid-liquid suspensions. The conventional velocity and resistance relationships for turbulent flow in fluids when applied to suspensions, do not take into consideration the two very important variables: suspension particle size and solid volume fraction. A study of the effect of suspension particle size (dgb) on the velocity of falling balls leads to the concept of a critical particle size (dgc) at which the suspensions will be Newtonian. This leads to the classification of static suspensions into two types: suspensions consisting of particle of diameter dgh > dgt, and those with dgh, < dgr. Separate velocity and resistance equations for these two types of suspensions have been proposed, taking into account both the solid particle size and solid volume fraction. The agreement between the velocities predicted from the proposed equations and the measured velocities, confirms their validity. The resistance force offered by suspensions to the movement of immersed bodies has been calculated from the proposed equations, and the effects of suspension particle size and solid volume fraction on the resistance force and velocity have been examined. The movement of immersed bodies in solid-liquid suspensions is of great importance in many areas of engineering such as minerals processing, oil well drilling, suspension flow in pipelines, and hydrometallurgy. A number of mineral dressing processes deal essentially with the movement of solids in suspensions—in particular, classification, thickening, filtration, ore washing, and gravity concentration—thus a study of the fluid characteristics of suspensions is of theoretical and practical interest.&apos; A rigorous analysis of the mechanisms of momentum transport of a solid-liquid system is complex indeed. The rheological properties of the suspensions deviate from those of liquids, varying, for example, with density, solid volume fraction, size and shape of the solid phase of the suspension, and with the density and viscosity of the liquid phase. The flow of suspensions around immersed bodies is mainly of a turbulent nature and hence studies of the turbulent flow characteristics of suspensions are of par- ticular importance. Problems are encountered when attempts are made to extrapolate the velocity and resistance relationships of Newton, pertaining to Newtonian systems, into non-Newtonian solid-liquid suspensions. Due to the numerous variables present in a suspension, certain limitations and assumptions become necessary in order to produce quantitative relationships for predicting their effects. The solid particle size and the solid volume fraction are two of the more important variables. By comparing the measured and calculated Newtonian velocities of falling balls in simple static suspensions, the existing velocity and resistance relationships have been modified to take these variables into account. In order to keep the study less complex, all other variables such as the characteristics of suspending liquid and shape of the particle are maintained constant. Objective The objective of the present investigation is to modify the Newtonian velocity and resistance equations in order to take into account the suspension particle size and solid volume fraction. Theory Liquids are classified on the basis of viscosity, which may be defined as the relationship between applied shear stress and resulting rate of shear.&apos; pure single-phase fluids composed of small light molecules behave as Newtonian liquids, having a single viscosity pa-

Jan 1, 1971

By D. Muraoka

Introduction Soda ash, anhydrous sodium carbonate, is produced from underground trona deposits occurring in the Green River Basin of southwestern Wyoming. Stauffer Chemical Co. of Wyoming, a jointly owned subsidiary of Stauffer Chemical Co. and Rocky Mountain Energy Co., mines the trona and processes it into high-purity soda ash. Stauffer Wyoming has been in operation since 1962 with a current production capacity of about 1.8 Mt (2 million st) per year of soda ash. The refinery has five parallel operating trains using the monohydrate process which is a series of chemical processing unit operations described below. Screening and Crushing The mined trona is brought to the surface in two counterbalancing ore skips. The ore is initially screened with refinery feed (less than peagravel size material) entering the process. Oversize is conveyed to an outdoor stockpile. Ore is recycled from under the stockpile via cone feeders as the refinery needs require. The ore is conveyed to hammer type crushers and screened. The refinery feed enters the process and the oversize is recycled to the crushers. Calcining The first step in refining trona to soda ash is calcining the trona ore. This is accomplished in concurrent flow, rotary kilns that are direct fired with natural gas. [2 (Na CO NaHCO 2H O) Heat 3Na CO + 5H20 + CO 2 3~3~ 2 ~~2 32] The trona ore is fed to the kiln at the burner end and is intimately mixed with the hot exhaust gases from the burner. Direct contact with the flame is avoided. The ore moves down the kiln by gravity and rotation aided by the kiln&apos;s internal lifters. The exhaust gases are cleaned to 99 + % particulate removal and discharged to the atmosphere. Dissolving the Calcined Trona The calcined trona is conveyed from the kiln discharge to a rotary drum dissolver where it is mixed with water and weak solution (unsaturated solution of calcined trona in water). The calcined trona is soluble whereas the impurities, primarily shale, are insoluble. The discharge from the dissolver is a slurry containing saturated solution (about 30% dissolved calcined trona in water), some undissolved calcined trona, insoluble impurities, and organic impurities. The dissolver discharge enters a rake classifier that makes the first solid/liquid separation in the process by removing the heavy undissolved material from the saturated solution. This undissolved material is conveyed to a second rotary drum dissolver and mixed with water to dissolve any remaining calcined trona. The secondary dissolver discharges to a second rake classifier that separates the solids from the liquid. The solids are now primarily insoluble impurities with very little unrecovered calcined trona. These wastes are conveyed to evaporation ponds for disposal. The liquid from the secondary rake is recycled to the primary dissolvers&apos; weak solution system. Returning to the primary rake classifier, the saturated solution which contains suspended insoluble muds is pumped to a thickener. Flocculant is added to aid settling of the suspended muds. The flocculated muds are collected at the bottom of the thickener and pumped to vacuum cloth filters. The adhering saturated solution is separated from the muds that remain on the filter cloth. The recovered solution is returned to the dissolvers&apos; weak solution system. The muds are reslurried and pumped to the evaporation ponds for disposal. Saturated solution, containing some suspended insoluble muds along with the organic impurities, overflows the thickener. Filtering the Saturated Solution The saturated solution overflowing the thickener enters a holding tank where it is pumped to a bank of pressure leaf filters. The suspended muds are captured on the filter leaves while the cleaned saturated solution is pumped to polishing filters. The polishing filters are also leaf pressure type, intended to remove any suspended solids that may pass the primary filters. Organic impurities are removed with activated carbon. The purified solution is now free of insoluble muds and has most of the organic impurities removed. Crystallizing and Drying the Monohydrate The purified saturated solution is pumped to evaporative crystallizers. The solution is circulated from the crystallizer vessel through a heat exchanger. Indirect contact with steam in the heat exchanger causes the saturated solution to boil, thus crystallizing the soda ash in its monohydrate form. Slurry crystal density is maintained in the crystallizer by simulta¬neous feed of fresh saturated solution and drawoff of the slurry.

Jan 1, 1986