Search Documents

By Paul Weir

BLEACHING clays have been used extensively in the oil-refining industries for a number of years. Their use in water purification is relatively recent and less extensive. They are frequently classified as (1) those naturally active and (2) those active after artificial activation with acid. Fuller's earths fall within the general group of bleaching clays and gradually the commercial term "fuller's earth" has been applied to natural clays originating, for the most part, in the south- eastern section of the United States. Bentonitic clays are usually classed as activable and are prevalent in the southwestern section of the United States. Bleaching clays vary considerably in chemical and physical properties throughout the country, or even in different parts of one deposit (Table 1). [ ] The fuller's earth type of clay is characterized by a lack of plasticity, relatively adsorbent, foliated structure, and does not swell to form a

Jan 1, 1939

By R. J. Brown

Design of a submarine pipeline system is governed by many factors, one of which is the effect of transverse horizontal currents on the pipeline structure itself Although this feature alone can be of utmost importance to the life span and stability of the underwater pipeline, it is usually the least recognized, with these hydro-dynamic forces being either completely overlooked or grossly underestimated. In an attempt to supply the methods and means for stabilization of sub-marine pipelines, much capital has been spent by pipeline companies. Design criteria incorporated by these organizations extend over a broad spectrum of engineering with bases varying from pure theory to cut and dry methods. A history of numerous failures has substantiated the postulate that many of these submarine pipelines have been underdesigned from the stability standpoint. By the same token, equally as many have been excessively overdesigned with resultant excess expenditures. An attempt has been made in this paper to establish the magnitudes of these hydrodynamic forces by measuring the lateral current-induced differential pressure distribution around the periphery of the submarine pipeline. INTRODUCTION The expenditure of money for research by corporations obviously requires beneficial results to justify the investment. One of the functions of the engineer is first to make the problem known and then to provide a means of solution at the least possible cost. The initial procedure is to investigate all pertinent published technical articles on the subject to determine if this problem has been previously solved. If resolution of this problem is not obtainable, the next course of action is to evaluate through experiments these forces and their magnitudes. On the specific subject of drag and lift, the accumulation of data is provided from three separate and distinct sources: from experience, from theoreticians and through experimental observations. The experience source has proved costly with money wasted either because of underdesign and failure or excessive expenditures for overdesign, and has not been sufficient to form a definite conclusion on these hydrodynamic forces. The pure theoretician is often not completely cognizant of the situation and his works bear little adaptation to the real problem. The experimentalist has his own problems with regard to obtaining results from small-scaled models and successfully adapting them to the larger prototypes. Each method has its own advocates who diligently adhere to their own separate routes as being the only means of resolving this problem. However, a review of the various methods of analysis leads one to the conclusion that if the advantages of all three are combined, a reasonable solution to this problem can be reached. Briefly then, the problem is to obtain the magnitudes of the forces on the submarine pipeline subjected to a lateral current by investigations of previous design considerations, by a study of existing theoretica1 data and by appropriate experimentation. This paper deals mainly with obtaining experimental data and the interweaving of theoretical and experience factors for resolution of these forces. APPARATUS AND PROCEDURE These tests were performed in 1961 at Collins Construction Co.'s main office near Port Lavaca, Tex. Test equipment consisted of a steel tank 3 ft high by 4 ft wide by 40 ft long, with several pumps circulating the water through the tank via suction lines from the downstream portion of the tank and discharging from the pumps directly into the upstream end of the tank. For reduction of turbulence, a wire section was constmcted in the upstream portion and straightening vanes in the form of pipes, screens, etc., were used to reduce the vortex and eddy action in the tank (Fig. 1). A venturi was built at the test specimen for obtaining velocity sufficient to simulate actual conditions. This full-scale test was initiated to eliminate the error introduced in modeling and obtain a truer picture of forces actually encountered. Six- and 10-in. specimens were prepared by

Jan 1, 1967

By C. S. Barrett

THE crystal imperfections known as faults in stacking (stacking disorder) are of importance to both fundamental and applied science and are receiving increasing attention. On the theoretical side there have been recent advances in the analysis of diffraction patterns in terms of stacking faults, and on the experimental side it has been found that certain metals develop a faulted structure on cooling through a phase transformation. Beyond this, little is known of what may be called the physical and mechanical metallurgy of faulting, although there has been no lack of discussion and conjecture as to the presence of faults in metals and the effect of faults on mechanical properties and microstructures. In the close-packed metals the nature of faults can be described very simply. Face-centered cubic (FCC) crystals consist of close-packed layers of atoms, (111) planes, stacked above each other in a definite manner. If one layer is designated as the A layer, the next must be a B or a C layer; that is, every atom of the second layer lies not above the atoms of the A layer, but nestles in the hollows between these, using the hollows designated as the B positions, or the equivalent hollows designated as C. If the sequence of layers is ABCABC...., so that layers three spacings apart are directly over each other, the crystal is FCC; if CBACBA ... it is an FCC crystal that is a twin of the former; if ABAB........or BCBC..it is hexagonal close-packed (HCP). A fault is a break in the sequence, such as ABCABABC .. . which has the effect of inserting an HCP lamella into an FCC crystal. Regularly spaced faults spaced two layers apart would convert an FCC crystal entirely to HCP, or an HCP to FCC. A fault in an FCC crystal is also equivalent to creating an FCC twin of minimum thickness; in fact, the entire crystal would be converted to its twin if faults were introduced regularly. (In HCP crystals, however, twinning does not occur on the basal plane and a fault on this plane is not identical with a thin twin). Faults are one of the possible causes for annealing twins,' for the strain markings that are brought out by etching deformed metal,'," for the altered X ray reflecting power of metal at slip bands that is revealed in X ray reflection micrographs,' for the extinction of Kikuchi lines in electron diffraction patterns, and for the hardening of latent slip planes.' Since other explanations of these effects are also available," there has been no direct proof of faults from deformation; yet it has appeared likely that they would occur. Faults resulting from phase transformations in metals, however, have been clearly revealed by diffraction in cobalt" and lithium. It is to be expected that the faulting tendency is greatest

Jan 1, 1951

By Om P. Garg

During the period between 1970 and 1974 the Iron Ore Company of Canada had embarked on a detailed program to evaluate all aspects of mine design work for its open pit mines around Schefferville, located both in Quebec and Labrador, Newfoundland, Canada. One of the main conclusions was that the majority of the slope angles for the ultimate pit walls could be steeped. During the period 1975 and 1976,five (5) open pit iron ore mines were redesigned using the steeper slope angles up to 55 degrees. Initially these pits were designed at slope angles varying between 37 degrees and 45 degrees due to the generally fractured and leached nature of rocks in the area. During the active mining phase between 1976 and 1979, the stability of the steeper ultimate pit walls was monitored. The mining of ore was successfully completed in 1978 and 1979 in three pits. This of course, resulted in a significant savings due to a reduction in the quantity of waste that had to be removed. The successful pit slope redesign project was a co-operative effort between the Federal Government, Universities and the Iron Ore Company of Canada.

Jan 1, 1983

By K. Mukherjee

A quasi-thermodynamic calculation is presented for estirt~ating vacancy Parameters in fcc metals. For fcc metals the equilibrium vacancy concentration at the melting point can be approximated by a constant mole fraction. The Gibbs free energy of formation of the vacancies can then be expressed as a simple function of the absolute melting temperature alone. From this description the formation energy Ef, the vibrational entropy Sv, and the formation volume of a vacancy can be calculated in terms of known thermodynamic parameters. The calculated values are in good agree-rnent with available experimental results. IT appears that many of the physical parameters associated with lattice defects can be empirically related to thermodynamic melting parameters.'-7 Besides the implicit correlations between melting phenomenon and point defects, the melting temperature itself at atmospheric pressure can be used as a reference temperature for the purpose of comparison of vacancy concentrations in a given crystal class. The concentration at the melting point then corresponds to the maximum vacancy super saturation in the crystalline state at a fixed pressure. For pure fcc metals such as Au, Cu, Al, Ag, Pb, and Pt the mole fraction of vacancies at the melting point8 is of the order of 10*"3 to 10"1. The equation expressing the equilibrium vacancy concentration at the melting point contains three parameters: the formation energy, the vibrational entropy, and the absolute melting temperature, see Eq. [2]. Since these three parameters cover a wide range of values8 in the above-mentioned metals, it can be assumed that in other fcc metals, for which no reliable data are available, the mole fraction of vacancies at the melting point most likely lies in the range 10~3 to lO"4. This is then the basis of the calculations described in this article. Within this range the mixing entropy can be linearized and the vibrational entropy, the formation energy, and the vacancy formation volume can be calculated in terms of known thermodynamic constants. 1} LINEARIZATION OF MIXING ENTROPY The Helmholtz free energy of a crystal containing n vacancies at the melting point can be writteng as where Ef, T,, k, and S, are the formation energy of a vacancy, the absolute melting temperature, Boltz-mann's constant, and the vacancy formation entropy, respectively. After applying Stirling's approximation in Eq. [l] and minimizing with respect to n where (n/N), is the equilibrium vacancy concentration in mole fraction at the melting temperature at 1 atm pressure. If instead of setting (6~/6n) = 0 immediately after Stirling's approximation in Eq. [I], the configurational partition function is simplified, then some useful and significant results can be obtained by utilizing the experimental inforrnation After applying Stirling's approximation and rearranging is plotted as a function of (n/N) in Fig. 1. The points, not all of which are shown, are fitted by a straight line substituting from Eq. [5] into Eq. [I] and minimizing with respect to n combining Eqs. [6] and [2] It must be emphasized that Eq. [7] is only a crude approximation based on an oversimplified model of

Jan 1, 1967

By Frank C. Kelton

A method is outlined for the analysis of large cores, developed primarily for the purpose of obtaining reliable data on fractured or vugular limestones. Porosity and fluid saturations are determined by a modified Dean-Stark extraction after initially bringing the samples to 100 per cent liquid saturation by a vacuum-pressure method. Horizontal permeabilities on the whole samples are determined in two directions, parallel and perpendicular to the di-rection of principal fracturing. Results are presented for various types of formations. A comparison is made between data obtained by this special method and the method of conventional analysis, and discussion is given of the relative advantages and limitations of each. In view of this comparison a modified method for the analysis of fractured and vugular formations is proposed, which method retains the advantages of the previously outlined techniques but gives promise of speeding up the analysis. INTRODUCTION For many years the greater part of the production in the Permian Basin was from formations of Permian and Pennsylvanian age. While production from these formations is still the predominant production. deeper prospecting has brought to light older formations with oil productive characteristics. Attempts to core these deeper horizons were at first usually characterized by poor recovery. The old rule of thumb, "good core recovery — poor well" was originated and remained in effect until recently. With the advent of diamond coring and the increased efficiency in drilling and coring operations. the old adage has lost its significance. Formations of Devonian. Silurian and Ordo-vician ages were successfully cored with varying degrees of recovery. The cores thus obtained were surprising and in some case; disappointing. Good recovery from these formations led to speculation as to the feasibility of analysis and the meaning of data obtained from conventional analysis. Commercial laboratories were engaged to analyze these cores. and their results indicated that data obtained by conventional methods would be of little value. From visual inspection it was apparent that in many cases the effective porosity for storage of hydrocarbons. and permeability. were contained largely in fractures and solution cavities rather than in the primary crystalline structure of the formation. In other cases the solution cavities augmented the effective porosity of the primary crystalline structure, or fractures enhanced the permeabiilty of the latter so that the formation might respond favorably to acidization and become commercially productive. Since the spacing of the cavities and fractures was often comparable to the core diameter, it was evident that the entire core should he analyzed instead of small fragments. On the basis of these observations, commercial laboratories were requested to devise a system of analysis which would yield data of practical value. Pro- cedures have accordingly been developed which seem to meet this requirement, and to date nearly 12,000 large core samples have been analyzed. It is the purpose of this paper to describe the methods used, to present typical results for several fractured formations and to compare the data obtained by this special analysis with that obtained by conventional analysis. Certain modifications and alternative procedures are finally suggested to speed up the analysis. CORE ANALYSIS PROCEDURE Fluid Saturations and Porosity The core sample, in segments up to 15 in. in length. is marked, weighed and examined under ultra-violet light to determine the presence of oil saturation. If present, the approximate quantity of oil and its location on intercrystalline, fracture or vugular surfaces is noted. This information is carefully recorded. The degree of fracturing and/or vugular development is also noted. The sample is then placed in a pressure cell and the air evacuated with a high speed vacuum pump. This evacuation is continued only long enough to reduce the pressure to approximately the vapor pressure of water in order not to remove excessive amounts of water. Water is admitted to the cell and allowed to penetrate the sample under atmospheric pressure, filling the pore space initially occupied by air and replacing the small amount of water removed by evacuation. Pressure up to 200 psi is applied to force water into the smaller capillaries, and the sample is left sub-

Jan 1, 1950

By R. K. Hopkins

For a great many years fusion welding has been used in and around petroleum refineries, but it is only within six or seven years that the more important pressure vessels have been constructed by this process, because before that time the properties of fusion welds would not with-stand such rigorous service. Since the adoption of fusion welding for the construction of this equipment, the refiner has required pressure vessels suitable for operation over a very wide range of conditions. On the one hand, vessels must operate at extremely high temperatures, in the range of 950° to 1000° F., and on the other vessels must be suitable for operation at sub-zero temperatures down as low as -75° F. Also, vessels are required suitable for operation at pressures upwards of 1000 lb. per sq. in., and as low as a 29-in. vacuum. In addition, vessels are required to withstand the attack of very corrosive mediums. It has been a rather difficult task for the fabricator to meet all of these require-ments, but as a result of the extensive research carried on by steel manu-facturers and several fabricators of class I vessels, practically all of these demands have been met. In order to meet the refiners' requirements for this wide range of conditions, the fabricator has worked closely with the metallurgist. This has enabled him to choose the proper base metal for each service condition, but it has been the fabricator's problem to develop a welding rod and welding technique, as well as a heat-treatment, that would produce in the welded vessel characteristics in and around the weld comparable to those in the base metal. Where corrosion is not a serious problem, and where the operating temperatures are not too high, ordinary carbon steel has served very well. But when corrosion is serious, and/or when the temperatures are either very high or very low, it is necessary to use some form of alloy steel to give satisfactory service.

Jan 1, 1935

By Hiroshi Kato, Shin’ichi Nagashima, Hiroshi Takechi

The preferred orientations detleloped during cold rolling, annealing, and hot rolling of low-carbon steel sheets have been investigated by means of an inverse pole figure technique. And X-ray line profile meas-urerrlents were made for the study of the factor which causes the textural changes between cold-rolled and recrystallized sheets. From ND (sheet normal divection) and RD (rolling direction) inverse Pole figures tlze axis detisity change with increasing cold reduction was measured and the Preferred orientations were analyzed. These results can be explained by crystal rotation due to slip during rolling deformation. The ND axis density change during annealing of cold-rollitig sheets is contrary to the change observed in the case of rolling. It was found that the orientation dependency of stored strain energy resulting from cold rolling apparently corresponds to the textural changes during recrystallization. The texture in hot-rolled sheets was found to be influenced by finishing tenlperatltre. In a sheet kol-rolled below the Ar, temperature a significant differernce in texture between the surface and central layers was obtained, the former having {hkl}(111} and {110 )(uvw) orientations and the latter having {pqr}( 110) orientation. A large number of investigations1 6 have been made on the textures of iron and low-carbon steel sheets, and, since it was shown7 13 that preferred orientations are closely related to deep drawability of steel sheets, studies14" 7 on the influence of production processes upon textures have been made from the standpoint of industrial interest. Generally, the textures in low-carbon steel sheets have several components of preferred orientations, but the overlapping of poles makes it difficult to analyze texture quantitatively from pole figures. On the other hand, an inverse pole figure directly expresses quantitative values of components of preferred orientations as the density of a certain sample axis with respect to the crystallite coordinates. Such a texture representation is desirable for a study of deep drawability. The purpose of the present work is to use both inverse and conventional pole figures, with emphasis on the former, to clar~fy the textural changes ~n low-carbon steel sheets by the production processes of hot rolling, cold rolling, and annealing. And the factor causing the textural changes during annealing is studied using an X-ray diffraction line profile technique. EXPERIMENTAL PROCEDURE Sheet specimens for study of cold rolling and annealing textures were taken from a hot-rolled strip of rimmed steel 2.7 mm thick. The chemical composition is shown in Table I. Although the study of cold-rolling textures requires a suitable material with random orientation, it is difficult to produce a perfect random one. But the used specimens, obtained from the hot-rolled strip with a finishing temperature higher than Ar3, were nearly random, such as shown in Fig. 15. These were cold-rolled to various reductions by a 4-high rolling mill with 150-mm-diam work rolls and 300-mm-diam backup rolls. The influence of hot-rolling conditions such as finishing and coiling temperatures on textures of hot-rolled strips was studied. The chemical compositions of these hot coils are given in Table I1 and the hot-rolling conditions are given in Table 111. inverse Pole ~i~ure -~easurement. Two methods for determining inverse pole figures with high precision have been proposed. The first, by Jetter et a1.,18 consists of obtaining mean densities of divided regions in a unit stereographic triangle by solving simultaneous linear equations to approximate the integral relation between conventional and inverse pole figures. The second, proposed by ~oe'~-'~ and Bunge,22'23 consists of determining an expanded series of spherical surface harmonics which express axis densities from several sets of pole distribution data. Both methods require laborious numerical calculations which make them unsuitable for practical use. However, the axis densities of the locations corresponding to low Miller indices in a unit stereographic triangle can be obtained

Jan 1, 1969

By A. F. Colombo, R. T. Sorensen, D. W. Frommer

An analytical method has been developed and used in batch and continuous tests to provide initial insights into the effect of soluble calcium ion in anionic flotation of silica from iron ores. A deficiency or excess of calcium ion in pulps subjected to this type of flotation produces an impairment in flotation efficiency. Data developed in the investigation are from a single ore, but show that total calcium requirement is met from water, ore and reagent sources. In batch studies, starch additions were shown to exert no influence on the calcium level, but fatty acid and sodium hydroxide had subtractive effects. The investigation was next extended to continuous flotation testing where the general observations from batch testing were confirmed. Factorially designed experiments were performed showing that the relationship of calcium additions to flotation response was not a simple one, but tended to shift to higher additions with increased fatty acid. Nevertheless, the range of soluble calcium levels measured remained fairly constant in areas of good flotation response. It is concluded that techniques developed should be useful in removing empiricism from flotation operations in this and other systems requiring activation for success. Further development should aid in process control both through methods outlined and through investigations aimed at studying the effects of other soluble reagents. Of the major mineral commodities, iron ore was one of the last to succumb to flotation processing. Commenting on this fact, one of the speakers 1 at the convention celebrating the 50th Anniversary of flotation in the U.S.A., said ". . . in 1951 froth flotation as a means of beneficiating nonferrous minerals was a might giant and could be characterized by 'you name it, we float' - but not iron ore". This tardiness in applying flotation to iron ores was the result of a number of factors, including economics and ready availability of direct shipping ores. Even now, when the need for beneficiation can no longer be denied, proposals for flotation of iron ores are apt to be viewed with some misgivings. This disquiet results from knowledge that wide variability, which would necessitate corresponding adjustments in reagents, often exist within even a single ore deposit. Coupled with ore variability is the fact that, at present, there is no way of quickly and precisely anticipating the direction and magnitude of reagent changes required for uninterrupted production of acceptable concentrates. Despite the long delay, iron ore flotation is now practiced commercially, although the chief applications2-4 are to specular hematites having relatively coarse liberation and low slime content. In addition, the application of flotation in upgrading magnetic concentrates seems assured. However, these flotation methods do not appear applicable to substantial tonnages of fine grained, earthy, and frequently more complex semitaconites and nonmagnetic taconites. The U.S. Bureau of Mines, in devoting its attention to the semitaconite and nonmagnetic taconite class of materials, has demonstrated that anionic flotation of calcium-activated silica can be utilized with an expected high frequency of success.' Even so, it has been recognized that the flotation method is a complex one, and that the reagent suite must be carefully tailored to the feed. These conditions would be expected to offer difficulties in treating ores with the wide range of variability previously discussed. Accordingly, research was initiated to develop methods to remove much of the empiricism from the flotation operation by measuring the reagent variables within the pulp for a correlation with flotation response. A simple illustration of the technique sought would be in the well established use of pH meters to provide feedback control to reagent feeders and thereby limit acidity or alkalinity to a range producing optimum results. The first efforts in this area have been concerned with measurements of soluble calcium ion. Bureau experience in both laboratory and pilot plant over the past five years has proved that the amount of calcium

Jan 1, 1965

By G. R. Gohn, S. M. Arnold

The results of stress-corrosion tests upon several non-ferrous sheet metals are presented in this paper. The metals include tough pitch copper, five binary brasses, two leaded brasses, one copper-silicon alloy, two tin bronzes, and two nickel-silver alloys. The tests indicate that for most of these sheet metals, externally applied bending stresses below the yield point (0.01 per cent offset) do not result in stress-corrosion cracking as determined by the A.S.T.M. Tentative Method of Mercurous Nitrate Test for Copper and Copper Alloys (B 154-41T).~ Only in the cases of low brass, high brass and medium leaded brass, all cold-worked 4 B & S numbers hard, was any corrosion cracking observed below the yield strength, and in all cases such failures occurred at stresses above the proportional limit for these materials. However, when some of the same materials which showed no evidence of stress-corrosion cracking at stresses below the yield strength, are stressed beyond the yield point, stress- corrosion cracking is quite apt to occur. Since experience has shown that some of these materials, particularly the brasses, are susceptible to stress-corrosion cracking under service conditions, these tests would indicate that, besides externally applied stress and corrosion, plastic deformation in addition to that resulting from the original cold working of the material is also required to produce conditions conducive to stress- corrosion cracking.

Jan 1, 1945

By D. L. Katz, M. J. Rzasa

The derivations of three methods of computing the static pressure gradients in natural gas wells have been presented to show the assumptions made. Charts were developed from which the pressure gradients may be read when the well-head pressure, the well fluid gravity, depth, and the average well temperature are given. A chart for estimating the well fluid gravity from the condensate content and separator gas gravity is included. The effect of the increased average well temperature after flow on the calculation of the static pressure gradient is discussed. Introduction Reservoir pressures have been calculated from well-head pressures for gas wells for many years. As the pressure measurements become more accurate, the need for a reliable calculation of the static pressure gradient often arises. This paper will develop the several methods for computing the pressure gradient in gas wells and make a comparison between them. The method of calculating static pressure gradients in common use is Eq. I (ref. I) or its counterpart which includes a factor for the deviation of the gas from the ideal gas law. P2 - P1 = P1(e0.0000347GX _ I) Eq. [I] in which P1 = pressure at well head, lb. per sq. in. abs. PP = pressure at bottom of well, Ib. per sq. in. abs. G = gas gravity X = depth of well, ft. An alternate method is to compute the average density of the gas in the well and multiply by the well depth in a manner similar to that used for liquid gradients. Derivation of Formulas A static pressure gradient is a special case of the general fluid-flow equation. Consider a pound of fluid flowing in a vertical column from point I to point 2, Fig. I. By an energy balance for fluid flowing from I to 2: U1 + P1V1 + u12/2g + X1 + q = U2 + P2V2+ u22/2g+X2 +W [2] in which U = internal energy, ft-lb. per lb. P = pressure, lb. per sq. ft. V = volume, cu. ft. per lb. u = average linear velocity, ft. per sec. X = height above datum, fl. q = heat absorbed by fluid, ft-Ib. pcr lb. W = work done by system, ft-lb. per lb. An energy balance on the fluid itself gives: U = ?TdS - ?PdV + etc. [3] in which T = temperature, deg- R- S = entropy, ft-lb. per deg. R. per lb.

Jan 1, 1945

By Henry E. Wood

In my opinion, the concentration of minerals by flotation is the most interesting problem in ore-dressing, and will command eventually far more consideration than it has at present. For many ores it furnishes a complete method of concentration absolutely independent of specific gravity, and thus simplifies the milling of many difficult combinations. Not having to recognize the influence of specific gravity, we are also able to dispense with some of the complications resulting from classifying-conditions. Where flotation cannot be used for a complete separation of the minerals from the gangue, it will be found, in nearly all cases, to save those portions which are generally lost by reason of their fine state of division. For this reason, it should be looked upon mainly as an aid to general concentration, although there are many ores so well adapted to flotation that more than 90 per cent. of the valuable metals can be recovered from them in one operation by this process. In presenting the results of my investigations in flotation, I have endeavored to theorize as little as possible. That side of the subject has been extensively discussed by others. My earliest work with flotation was done in 1895, when I used various oils, grease, soap, etc., with results that were remarkable. I did not realize then that with water alone equally good separations could be made. Up to 1906, my endeavors were confined to attempts to keep the concentrates on the tables well wetted and away from exposure to the air. In common with others, I observed that when there mas any obstruction in the wash-water on the table of sufficient size to divert the water to either side, the concentrates collected, and, on exposure to the air, would promptly float away. This convinced me that the sulphides were all good "swimmers," and that if,

Jan 1, 1913

THE Copperton mill in reality was a sort of proving ground. It was. designed to serve three purposes: (1) to verify the accuracy of the mine sampling by actually treating substantial tonnages of ore, (2) to demonstrate on a reasonably large scale the percentage of the copper in the ore that could be recovered, and (3) to permit the testing of various kinds of machines and devices for crushing and concentrating the ore, so as to guide the engineers in designing the proposed 6000-ton milling plant at Garfield. As a matter of fact, it contained a lot of second-hand equipment sent by MacNeill and Penrose from the works of the United States Reduction &Refining Co. in Colorado; and it was by no means a model installation. Probably it would have been even less efficient, except for the skillful work of George O. Bradley and-Frank-G, Janney, both of whom had worked with Jackling at Mercur. Bradley was a mechanical engineer employed to design the plant. Later he directed the design of the concentrator at Garfield and remained as consulting mechanical engineer to the company until 1915. Janney, who afterwards became manager of mills, a position that he retained until his death in 1916, was a skilled mechanic at the Golden Gate mill at Mercur when Jackling built the plant in 1897. His flair was making machinery do what it was intended to do. He was not an ore-dressing engineer in a technical sense; but Jackling him- self was a specialist in this respect as well as in designing and construction and Janney's mechanical aptitude made him a particularly valuable man in the Utah organization. John McDonald, another of Jackling's Mercur associates, was the first mine superintendent. With practically all of the available funds earmarked for construction of the Copperton

Jan 1, 1933

By R. H. B. Jones

This paper reviews pertinent geology of the Biwabik iron formation, Mesabi Range, Minnesota. This iron formation is divisible into four members. Each member is distinctive and contains marker horizons, which are recog nizable throughout all phases of alteration from lean, fresh rock to high-grade iron ore. Some beds have a larger magnetite content than others. During the process of ore genesis, which is essentially an oxidation process, the magnetite content is lowered. Alteration from iron formation to ore includes both oxidation of iron minerals and silica removal by leaching and these distinct processes progress at variable rates for different locations and structures. Magnetic intensities, of each horizon of the iron formation are dependent chiefly upon its preoxidation magnetite content, upon the subsequent degree of oxidation, upon the character of the enclosing rocks, and on the extent of fracturing, folding, or faulting. The results of a number of magnetic surveys are described and are correlated with results of drill-hole and mine exploration and developmerit. The magnetic anomalies obtained are discussed in relation to phases of formation of ore within the iron formation. General Information One hundred years ago a party of surveyors, applying the principles of geophysical prospecting, discovered iron ore in the state of Michigan in the Lake Superior district. This event was officially reported as follows:' On Sept. 19 (1844) while running the east line of Town 47 North, Range 27 West, they observed by means of the solar compass remarkable variations in the direction of the needle, amounting to 87" from the normal. Ascribing this phenomenon to iron ore, they sought and found it in ledges or outcrops at several points. The solar compass referred to was invented by William A. Burt, deputy surveyor in charge of this party.2 It is used for determining the true meridian by an observation on the sun. Eight years later, on July 7, 1852, the first iron 're, consisting of 6 bbl. of Ore, was shipped from Marquette, Michigan. It was another 40 years before the first or> shipment left the Mesabi Range in Minnesota, in October 1892. It totaled 4245 tons. Fifty years later, 90 years after the original shipment, during 1942 the Lake Superior district shipped 93,495,392 gross tons of iron ore. Production came from Minnesota, Michigan, Wisconsin, and Ontario, Canada. Throughout the 90-Year period it was known that magnetic properties of most of the ore bodies, and of the iron formations in which they occur, affected the compass. This phenomenon, later to be made use of to outline areas of ground favorable for exploration, was at first a

Jan 1, 1949

By R. H. B. Jones

This paper reviews pertinent geology of the Biwabik iron formation, Mesabi Range, Minnesota. This iron formation is divisible into four members. Each member is distinctive and contains marker horizons, which are recog nizable throughout all phases of alteration from lean, fresh rock to high-grade iron ore. Some beds have a larger magnetite content than others. During the process of ore genesis, which is essentially an oxidation process, the magnetite content is lowered. Alteration from iron formation to ore includes both oxidation of iron minerals and silica removal by leaching and these distinct processes progress at variable rates for different locations and structures. Magnetic intensities, of each horizon of the iron formation are dependent chiefly upon its preoxidation magnetite content, upon the subsequent degree of oxidation, upon the character of the enclosing rocks, and on the extent of fracturing, folding, or faulting. The results of a number of magnetic surveys are described and are correlated with results of drill-hole and mine exploration and developmerit. The magnetic anomalies obtained are discussed in relation to phases of formation of ore within the iron formation. General Information One hundred years ago a party of surveyors, applying the principles of geophysical prospecting, discovered iron ore in the state of Michigan in the Lake Superior district. This event was officially reported as follows:' On Sept. 19 (1844) while running the east line of Town 47 North, Range 27 West, they observed by means of the solar compass remarkable variations in the direction of the needle, amounting to 87" from the normal. Ascribing this phenomenon to iron ore, they sought and found it in ledges or outcrops at several points. The solar compass referred to was invented by William A. Burt, deputy surveyor in charge of this party.2 It is used for determining the true meridian by an observation on the sun. Eight years later, on July 7, 1852, the first iron 're, consisting of 6 bbl. of Ore, was shipped from Marquette, Michigan. It was another 40 years before the first or> shipment left the Mesabi Range in Minnesota, in October 1892. It totaled 4245 tons. Fifty years later, 90 years after the original shipment, during 1942 the Lake Superior district shipped 93,495,392 gross tons of iron ore. Production came from Minnesota, Michigan, Wisconsin, and Ontario, Canada. Throughout the 90-Year period it was known that magnetic properties of most of the ore bodies, and of the iron formations in which they occur, affected the compass. This phenomenon, later to be made use of to outline areas of ground favorable for exploration, was at first a

Jan 1, 1949

By H. M. Faust

THERE are a number of different types of power plants. Some use coal to generate steam, others use oil or gas either in the form of steam or internal combustion equipment, while still others avail themselves of water power as a source of energy. A general comparison of the relative power production with different sources of energy in the United States, for several different years is set up in Table 1. This table shows that coal was used to generate 85.6 per cent of the total heat power requirements of 1909, and only 59.2 per cent of the 1930 requirements. The increasing proportion of modern heat energy generated by the use of fuel other than coal is apparent. If coal is to maintain its importance as a source of heat energy, the necessity for its improved perform-ance, in which preparation plays an -important part, cannot be stressed too strongly.

Jan 1, 1933

By E. C. Wright

The following article is based on observation of college graduates entering the steel industry in technical work made during the Past 25 Years, the first five of which were spent as a college instructor in two engineering schools, and the last 20 in the employ of a large steel company that has hired hundreds of engineering graduates for steel-mill operations. The college graduates encountered during this period have come from many colleges representing schools in Eastern States, Midwestern Universities, many Southern colleges, and many smaller colleges and normal training schools mostly in western Pennsylvania and Ohio. The college training of these students for engineering work naturally has varied widely and the educational qualifications of the entrants have been in many ways different. It was found at an early date that graduates of standard engineering colleges were much more adaptable than graduates in science from nontechnical schools. The engineering students seemed to be more suited to actual work in steel plants and in general were better able to grasp a knowledge of the operations they observed. However, although the graduates of engineering schools have had somewhat better training in physics, mathematics, and engineering, it has been a general and continual observation that most of the students employed have had inadequate training in the fundamental sciences. Since this discussion relates entirely to metallurgical engineers it should be emphasized that students taking metallurgical engineering courses in college seem to be poorly trained in organic chemistry-physics, physical chemistry, thermodynamics, and any higher form of mathematics than simple calculus. It has been noted frequently that young engineers faced with problems in a mill that involve some mathematics generally flounder badly, and that they have little conception of physical chemistry. Another common deficiency lies in the young graduate's lack of knowledge of where to look for the more detailed literature on any subject. He reverts instinctively to some college textbook whose coverage is usually very elementary. It is recommended that such textbooks contain a bibliography of the source literature. and that students be taught to use the original data. Many of the students had had previous courses in college dealing with metallurgical work such as steel melting, metallograhy, etc.r but it was found that their grasp of these subjects was extremely sketchy. It was soon realized that an ordinary engineering graduate could be taught more about steel melting and manufacturing processes in a few weeks in a plant than he could learn in a college course on such subjects. A similar statement may be made regarding the ability of students to conduct laboratory work. Their lack of technique and skill in handling equipment and setting up experiments was soon apparent. It became neces-

Jan 1, 1948

By E. C. Wright

The following article is based on observation of college graduates entering the steel industry in technical work made during the Past 25 Years, the first five of which were spent as a college instructor in two engineering schools, and the last 20 in the employ of a large steel company that has hired hundreds of engineering graduates for steel-mill operations. The college graduates encountered during this period have come from many colleges representing schools in Eastern States, Midwestern Universities, many Southern colleges, and many smaller colleges and normal training schools mostly in western Pennsylvania and Ohio. The college training of these students for engineering work naturally has varied widely and the educational qualifications of the entrants have been in many ways different. It was found at an early date that graduates of standard engineering colleges were much more adaptable than graduates in science from nontechnical schools. The engineering students seemed to be more suited to actual work in steel plants and in general were better able to grasp a knowledge of the operations they observed. However, although the graduates of engineering schools have had somewhat better training in physics, mathematics, and engineering, it has been a general and continual observation that most of the students employed have had inadequate training in the fundamental sciences. Since this discussion relates entirely to metallurgical engineers it should be emphasized that students taking metallurgical engineering courses in college seem to be poorly trained in organic chemistry-physics, physical chemistry, thermodynamics, and any higher form of mathematics than simple calculus. It has been noted frequently that young engineers faced with problems in a mill that involve some mathematics generally flounder badly, and that they have little conception of physical chemistry. Another common deficiency lies in the young graduate's lack of knowledge of where to look for the more detailed literature on any subject. He reverts instinctively to some college textbook whose coverage is usually very elementary. It is recommended that such textbooks contain a bibliography of the source literature. and that students be taught to use the original data. Many of the students had had previous courses in college dealing with metallurgical work such as steel melting, metallograhy, etc.r but it was found that their grasp of these subjects was extremely sketchy. It was soon realized that an ordinary engineering graduate could be taught more about steel melting and manufacturing processes in a few weeks in a plant than he could learn in a college course on such subjects. A similar statement may be made regarding the ability of students to conduct laboratory work. Their lack of technique and skill in handling equipment and setting up experiments was soon apparent. It became neces-

Jan 1, 1948

By J. L. Wyatt

The electrical resistance of titanium as a function of purity and temperature was measured from —325" to 2800°F. Two points of inflection in the data plots were found, and an increase in resistance with increase in temperature above the transformation was observed. IN 1948 Greiner and Ellis' reported on the thermal and electrical properties of titanium, including a study of the effect of temperature on the electrical resistance. The materials used in the research were obtained from the United States Bureau of Mines, where powder metallurgy techniques were being employed for consolidation purposes. These authors found a decreasing resistance with increasing temperature above 1625°F, and concluded that the latter temperature represented the point of transformation from hexagonal close-packed to body-centered cubic structure on heating. They reported a specific resistivity value of 55x10-6 ohm-cm, and showed that dp/dt was positive, decreasing with increasing temperature above ambient. In one of his early texts Hume-Rothery2 mentioned that certain metals, including titanium, exhibited minima in plots of resistance vs temperature. He indicated that this occurred at 212°F. Reporting many years ago on the effect of temperature on the electrical resistance of zirconium, de Boer and Fast³ showed that phase transformation in this sister metal occurred over a range of temperatures, the extent varying with its purity. Graphs of resistance vs temperature, showing transformation effects over a range of several hundred degrees, were presented for relatively impure metal. In the latter case the resistance decreased with increasing temperature throughout the region of partial phase transformation, thereafter increasing as predicted for normal metals by modern theories of the solid state. Since the quality of metal used in previous studies was substandard compared with iodide-type titanium, and in view of the fact that there seemed to be some rather unusual observations in the reported literature, it was decided to undertake a more extensive study of the thermal effects using high purity titanium, and to include temperature ranges beyond those which had been studied in order to ascertain whether or not the characteristics of zirconium would be duplicated. Experimental Materials Materials used in this investigation included commercial quality titanium (Ti-75A produced by the Titanium Metals Corp. of America) in the form of ¼ in. diam rods, and high purity iodide titanium (produced by the Foote Mineral Co.) in the form of crystal bar of irregular size. The latter was cold-swaged into rod form and machined to the desired size. Lead wires to all specimens consisted of 18 gage Ti-75A. Chemical analyses of the stock materials are given in Table I. Experimental Procedures Specimens 2½ to 3 in. in length were prepared with diameters nominally 0.15 to 0.20 in. Two holes,

Jan 1, 1954

By Enrique Touceda

For a number of years prior to the world war, the firm of Geo. H. Thacher & Co., of Albany, N. Y., was engaged in the manufacture of marine and other gray-iron castings. At the outbreak of the war the firm decided to specialize in the manufacture of propeller wheels. It attacked the problem, therefore, from a foundry point of view, seeking to produce a casting that would be so accurate that no subsequent machining would be required on the blades, also from the point of view of the ship builder. There were two general methods of manufacture, the shortcomings of which have been freely acknowledged. In the sweep method, the nowel, or bottom half-mold, for each blade is swept up by a spindle beam and pitch race, while the top half-mold for each blade is built up individually. In the pattern method one individual blade, with the hub or hub portion, is mounted on a spindle and the individual blade mold formed, the pattern is then rotated on the spindle to the position for the next blade, etc. In rare cases wheels were made from a solid pattern. Owing to the cost of the pattern, its failure in many instances to be correctly made, and (when made of wood) its early and sure distortion the disadvantage of this pratctice is obvious, while metal patterns in most instances were prohibitive in cost. In these methods both green-sand and loam molding was practiced. The casting produced by either method can be considered only as a blank from which the propeller must be machined. The back surface of each blade must be chipped to the templet and through this procedure chipped to such accuracy as will be required for a static balance. Inasmuch as the work done by the machine tool is confined to the driving face of the blades, not only is perfection most difficult, but corrosion will be greater because of the removal of the dense skin of the casting and the local strains set up by the pneumatic tool in chipping. To produce a finished 9-ft. propeller for a Navy destroyer required from 8 to 21 days of foundry work and about the same length of time for the machining. Through the use of the Thacher process, only as many hours are required, besides it is possible to produce a finished casting in perfect conformity with any particular propeller-wheel design.

Jan 1, 1922