Search Documents

By R. J. Marcotte, C. T. Eddy, R. J. Smith

THE objectives of the investigation herein reported were to determine: (I) the S-curves for certain selected cast steels, (2) whether or not the published S-curves for wrought steels are satisfactory for use on cast steels of similar composition, and (3) to prepare hardenability curves of the selected cast steels. In order to make the final comparisons between cast and wrought steel more completely tangible, it was deemed advisable not only to determine S-curves for the steels submitted in the cast condition but also to roll some of the cast-steel test bars and determine comparison S-curves on such wrought material. This procedure eliminates the composition variable and makes it possible to reveal the differences resulting from plastic deformation of the cast structure in addition to providing the comparison with published data on wrought steels. CAST STEELS The cast steels selected for the preparation of S-curves, or time-temperature transformation curves, were similar to S.A.E. series 1030, 2330, 4130 and 4330. Of these the 1030 was supplied by The Crucible Steel Casting Co., Cleveland, Ohio, and the other three by The Sawbrook Steel Castings Co., Lockland, Ohio. The steels were furnished in the as-cast condition. The manufacturers supplied the chemical analyses and the properties that could be obtained in the heat-treated condition-all of which is summarized in Table I. [ ] PROCEDURE The metallographic and dilatometric procedures and equipment were in general standard. The specific technique employed was described in a report of the Steel

Jan 1, 1945

By H. F. Korman, M. C. C. Mow, P. K. Dai

INTRODUCTION Detonations of high explosives in soil and rock have been used frequently in civil engineering applications. Of particular interest in recent years has been the development of test methods to simulate the desired blast and shock environments for the testing of protective structures. The United States Air Force, in particular, the Air Force Weapons Laboratory, in conjunction with the Defense Atomic Support Agency, has in recent years, developed special technology for simulation testing of protective structures in soil and rock media. Such a technology, although initially developed for military applications, is rapidly finding its way into civil applications. One of the major problems in the design of the simulation test is the correct prediction of ground motion induced by the detonation of high explosives. This paper presents a useful prediction method which is developed specifically for ground motion in rock that is induced by the detonation of a buried planar array of explosive columns (See Figure 1). The technique of simulating shock environment using such an array is called the Direct Induced High Explosive Simulation Tech- nique (DIHEST). Normally, each shot hole may contain canisters of ammonium nitrate positioned at various depths, or a slurry explosive with detonators positioned along its length (See Figure 1). The depth and width of the array, the spacing of shot holes, the spacing of detonators, the degree of containment, and the charge weight are the variables which govern the induced ground motion

Jan 1, 1971

By W. L. Zeigler

During the middle 1880's, shortly after the discovery of silver-lead ores in the Coeur d'Alene district of northern Idaho, it became apparent that concentration of the ores would be necessary to obtain a profitable product. Too much siliceous material was present for direct smelting, and the majority of the ores found at depth were too low in metallic content for economic smelting processes at the time. As the ores occurred in quartzite shear zones with siderite and quartz gangue, a large quantity of waste material was present in all the mines. As the galena was not finely disseminated, this made possible relatively good extraction of the argentiferous galena by coarse concentration. The first concentrators consisted mainly of coarse crushing, screening and jigging, principally by Harz jigs, the slimes being treated on buddles. Later Wilfley tables took the place of sand jigs and vanners superseded the buddles. Because of the marketing conditions, no attempt was made until 1900 to effect a recovery on the zinc minerals present, which were found associated in varying amounts with the galena. All through this period, the greater part of the production was obtained from mines containing ore assaying high in lead and low in zinc. Parts of some ore bodies would be reversed in this respect, so that ores high in zinc were left intact. During the decade after 1910, several important mines, The Success and The Interstate Callahan, containing ores high in zinc, were put into operation and were a material aid in the needed zinc production during World War I. Gravity concentration by jigs and tables was used during this period, with bulk flotation increasing in popularity for the treatment of the fine material that had already been treated by ordinary slime concentrating machinery. No extra fine grinding for flotation concentration was thought profitable at the time. Tailings Discharged into Streams From the start of mining and milling operations in this district until 1904, no attempt was made by the various mills in the upper district to impound or stack their tailings. They discharged them directly into the adjacent creeks or streams, to be carried away by high water. The Bunker Hill and Sullivan and the Last Chance mines, both in the relatively flat valley of the district, stacked huge piles of the coarse jig tailings on the near-by river bottom. Rain and snowfall are heavy in the Coeur d'Alene district, as it is on the heavily timbered Pacific slope of the Bitter Root Mountains. A heavy runoff occurs every spring and there is an occasional flood of disastrous proportions when warm "Chinook" winds accompanied by rain

Jan 1, 1949

By Ross Glanville

INTRODUCTION The Optimum Production Rate (OPR) is one of the most important parameters in the evaluation of a mineral deposit. The OPR can also be expressed as the Optimum Mine Life (OML) in years since the expected mine life is determined by dividing the OPR per year into the estimated ore reserves. Unfortunately, very little time and effort has been directed towards the determination of the OPR. Instead, "rules of thumb" are often applied to select a mine life without due consideration of the economic implications of such a selection. A "justification" for a particular production rate is often based on a pre-conceived arbitrary requirement for a mine life of 5, 10, or 15 years, for example. In this paper it is demonstrated that such arbitrary selections for high-grade/low-tonnage mines (such as many underground gold/silver deposits) often lead to sub-optimal results. In fact, an apparently uneconomic deposit at an arbitrary production rate may be economic at the OPR. Consequently, investment opportunities may be overlooked if one analyzes mine properties based on arbitrary production rates. This paper analyzes the interrelationships of variables such as production rates, capital and operating costs, cut-off grades, discount rates, metal prices, etc. The analysis shows that the OML for high-grade/low-tonnage deposits is often in the range of two to four years. Although such mine lives intuitively appear too short to many individuals, it should be noted that, in the past, much of the mining industry became familiar with the economics of large scale mining operations. The rules of thumb developed for such large scale operations should not be applied to high-grade/low-tonnage mines such as many of the underground gold deposits. DEFINITION OF OPTIMUM PRODUCTION RATE The OPR is selected on the basis of maximizing the net present value of the after-tax cash flows. However, as discussed later in this paper, the production rate selected for a particular mine may be somewhat higher or lower than the theoretical OPR as a result of other variables such as: 1) the probability or expectation of additional reserves being discovered 2) the likelihood of being able to custom mill nearby deposits owned by others 3) the configuration or attitude of the orebody, which may place upper limits on the production rate 4) the residual, or salvage values, of the mine/mill facilities COMPARISON BETWEEN DIFFERENT PRODUCTION RATES For an orebody with definite physical cutoffs*, or boundaries (such as faults or unconformities), the total ore reserves at different production rates may be identical. Consequently, for such an orebody, varying production rates result in differing mine lives. Although the metallurgical recoveries, the mine dilution, and other similar physical parameters may vary slightly at different production rates, the major differences are the capital costs and operating costs per ton. The ramifications of these differences are especially important at low production rates (up to approximately 1000 tons per day), but can also be significant at higher production rates.

Jan 1, 1985

By M. A. Scheil, S. L. Hoyt

About three years ago eight standard steels were prepared for the cooperative investigation of methods for oxygen analysis, sponsored by the Iron and Steel Division of the American Institute of Mining and Metallurgical Engineers and by the National Bureau of Standards. A preliminary report of the results was made at the annual meeting of the A.I.M.E. in February, 1936. † This report showed the reliability of vacuum-fusion methods and further brought out certain advantages of the fractional vacuum-fusion method. The results obtained by the authors with the latter method will be discussed here, with some comments on the procedure for those who are interested in determinations of gases in steel. Some additional comments are offered on the use of the polarizing microscope for identifying the inclusions in the steel to check and amplify the findings of the fractional vacuum-fusion analysis. For details of the fractional method, see the paper by L. Reeve1. Degassing the Crucible One of the sources of error in vacuum-fusion methods has been the blank gases evolved from the graphite crucible after preliminary out-gassing. We have used 1750" C. as the outgassing temperature. This gives a base pressure at that temperature of less than 0.030 mm. after one hour and of 0.004 mm. on dropping the temperature to 1575" C. At lower extraction temperatures the base pressure is 0.001 mm. at 1050" C., 0.002 mm. at 1170" and 0.003 mm. at 1320' C. Because of the size of our induction coil we are limited to this temperature, although it 'would be advantageous to use 1950" to 2000" C. Hamilton2, after outgassing at 1850" C. for 100 min., was able to reach a base pressure of 0.001 mm. for a temperature of 1700' to 1725" C. This would give a blank corresponding to less than 0.00015 per cent 02 and 0.00005 per cent H2. Chipman and Marshall outgas at 2000" C. for one hour by using a special construction

Jan 1, 1937

By Roger M. Nendick

The recovery of precious metals from heap leach solutions can be accomplished by two processes: 1. The Carbon Adsorption Process 2. The Merrill-Crowe Zinc Precipitation Process A brief review of the relative process economics is made. Each process presents certain design considerations that must be addressed during the evaluation and engineering design for the project. Discussion is presented on the design criteria for each process.

Jan 1, 1984

By G.A. Moore, C. E. Sims

In previous publications of the writers4-7 it has been shown that vacuum extraction of steel can be carried as close to quantitative completion as desired provided the steel is in the austenitic state and sufficiellt time is allowed. For precise work, the method claims preference because the equipmelit for holding and heating the sample can be made simple, and because crucibles, boats, and other unnecessary materials can be eliminated and the blanks thus made very small. It is well known that the evolution rate of hydrogen is smaller just above the trans. formation than immediately below, as would be expected from the increase in solubility when passing into the gamma state. Many attempts have been made to obtain analyses by extraction just below the transition, using times of approxi. mately 2 hr. while it is true that the rate of evolution drops nearly to zero under these conditions, it has repeatedly been shown that the process is incomplete since on raising the temperature into the austenitic range, evolution will be resumed, usually after a, considerable induction period. The low-temperature evolution process appears to be useful in some cases for comparative tests where the residual crror may be more or less constant between samples, For general use, however, there is no guarantee that the error caused by incomplete extraction is constant; hence, the more laborious but more reliable high-temPe'atu'e Process must be used. At high temperature, an original flash evolution, similar to that at lower temperature, is first observed. After not more than an hour, the flash subsides and cvolution settles down to a regular first-order reaction rate for which the half-life* is usually of the order of a few hours for the 5/8-in. diam cylinder at 1050°C. The regular evolution may be followed for whatever period appears justified, after which the residual gas may be estimated as equal to that which was evolved in the last observed half-life period. Tests have shown that the composition of the evolved gas does not vary greatly during the progress of evolution; therefore the residual gas may safely be taken to have the same composition as the portion col-

Jan 1, 1949

By C. E. Sims, G. A. Moore

In previous publications of the writers4-7 it has been shown that vacuum extraction of steel can be carried as close to quantitative completion as desired provided the steel is in the austenitic state and sufficiellt time is allowed. For precise work, the method claims preference because the equipmelit for holding and heating the sample can be made simple, and because crucibles, boats, and other unnecessary materials can be eliminated and the blanks thus made very small. It is well known that the evolution rate of hydrogen is smaller just above the trans. formation than immediately below, as would be expected from the increase in solubility when passing into the gamma state. Many attempts have been made to obtain analyses by extraction just below the transition, using times of approxi. mately 2 hr. while it is true that the rate of evolution drops nearly to zero under these conditions, it has repeatedly been shown that the process is incomplete since on raising the temperature into the austenitic range, evolution will be resumed, usually after a, considerable induction period. The low-temperature evolution process appears to be useful in some cases for comparative tests where the residual crror may be more or less constant between samples, For general use, however, there is no guarantee that the error caused by incomplete extraction is constant; hence, the more laborious but more reliable high-temPe'atu'e Process must be used. At high temperature, an original flash evolution, similar to that at lower temperature, is first observed. After not more than an hour, the flash subsides and cvolution settles down to a regular first-order reaction rate for which the half-life* is usually of the order of a few hours for the 5/8-in. diam cylinder at 1050°C. The regular evolution may be followed for whatever period appears justified, after which the residual gas may be estimated as equal to that which was evolved in the last observed half-life period. Tests have shown that the composition of the evolved gas does not vary greatly during the progress of evolution; therefore the residual gas may safely be taken to have the same composition as the portion col-

Jan 1, 1949

By J. L. Shafer, Christopher L. Caenepeel, Martha L. White

Often an in situ leach is the only practical economic method for copper recovery from small low grade oxide deposits. The decision to develop a copper property by an in situ blast and leach is strongly dependent on ore grade, tonnage, hydrology, and the copper extraction and acid consumption rates. The inherent leachability of the ore will in part determine the desired amount of fracturing of the ore deposit by the blast in order to obtain a copper extraction rate that is economical. For the last several years Occidental Research Corp. (ORC), has undertaken a modest effort to address the question of how to best identify and determine the information necessary to predict and control the operation of an in situ leach for the economic recovery of copper. Modelling of the Leaching Process During the past 10 years the activity in the mathematical modelling of the leaching of copper sulfides in copper dumps and heaps has increased dramatically. The modelling of copper oxide leaching has not received as much attention. The acid leaching of non-sulfide copper minerals while chemically less complex, compared to sulfides, does generate a vertical acid concentration gradient in the ore heap being leached due to the acid-base nature of the reaction. This is generally not observed in sulfide deposits that are biologically active, due to the buffering action of opposing reactions involving the generation of sulfuric acid from sulfide minerals and acid consuming host rock. Thus, the objective of ORC 's copper oxide modelling efforts is to determine the leaching parameters which will account for this vertical acid concentration gradient. Knowledge of this gradient will result in the correct choice of the feed acid concentration to the top of the ore dump or heap, such that the effluent will have the desired pH.

Jan 1, 1980

F. Lynwood Garrison, Philadelphia, Pa. (communication to the Secretary): I have been specially interested in Mr. Drake's valuable contribution to our knowledge of the Chinese coalareas, as I had occasion, about a year ago, to make a reconnoissance over some of the coal-fields in the Yangtse river valley. I noticed, as he appears to have done, certain peculiarities which may eventually prove to be characteristic of the Chinese coal-measures, at least in central and northern China. The most striking feature, perhaps, is the invariable proximity of the great granite masses to those coal-deposits which have an anthracite character. In common with all other anthracite areas elsewhere, the Chinese show evidences of profound stratigraphical disturbances. The sedimentary rocks are folded, faulted and dislocated in a manner similar to those of the Pennsylvania anthracite-regions. It would seem that the intrusive granite had much to do with converting the original bituminous into present anthracite. The action of the granite was probably direct as a conveyor of heat, and indirect as dynamic force in dislocating, overturning, and compressing the coal-measures. My stay in China was unfortunately cut short, so that I was unable to collect fossils, or to give this highly interesting and important subject more than passing attention. Cholnoky* and Richthofen are practically agreed that these granite eruptions took place during the Tertiary period—probably the Eocene. This profound tectonic movement has had a most important effect upon the geological conditions in central and northern China, and will be, I am sure, a potent factor in the economic development. Evidences of disturbances and metamorphism are very abundant in the anthracite-areas of the Yangtse valley. I noticed the coal in them, as did Mr. Drake in northern China, to be often flaky and " slickensided."

Jan 1, 1902

By Z. T. Bieniawski

Tunneling in coal mines includes driving the main haulageways or roadways which serve as the development entries. Although constituting the lifelines of these mines, little attention has been paid to development entries in the United States in terms of systematic pre-construction planning and design. Coal mine tunnels, as the terminology is used in Europe and elsewhere, are understood in the United States to be the main development entries, either in room-and-pillar mining or in longwall mining. These development entries are not tunnels in the traditional sense since they usually are of a multi-entry type involving entries and cross-cuts, and their intersections. Thus, the design of coal mine tunnels is intertwined with the design of coal pillars. This paper summarizes the results of a three-year research project aimed at improving the design of development entries in U.S. coal mining. A design approach has been developed for this purpose and design procedures for roof support in main entries and for pillar sizing are proposed.

Jan 1, 1984

By Howard Eavenson

PRIOR to 1907 nearly all coke was made in beehive ovens, and most of the gas produced was made in the old-style gas retorts, and while there were a few coke plants in southern West Virginia, southwest Virginia and Kentucky operating on high-volatile coals the proportion of the total product made by them was small and was usually used locally. The greater part of the coke made, and the coal gas produced, came from the Pittsburgh seam of western Pennsylvania and northern West Virginia-which was then regarded as the standard coking and gas coal of the coun, try, and the best coal available anywhere for these purposes. With the advent of the by-product oven and the building of coke plants at the furnaces, the restriction of the use of one grade of coal for making coke was removed and the use of mixtures of low-volatile and high-volatile coals began. The change in the locations of the coke plants removed the necessity of using Connellsville coal and also made sources of gas available to the public utilities other than of their own manufacture. Most of the first oven plants were built at points distant from the Connellsville region and this afforded an opportunity for the use of coals from the southern Appalachian fields, which were at approximately equal distances from the ovens. Since that time development has been made on a number of seams of coal of great purity in southern West Virginia, southwestern Virginia and eastern Kentucky, which have been largely used for cokemaking, gas and other metallurgical purposes where low amounts of ash, sulfur and phosphorus are determining factors. These coals are much lower in the objectionable elements than the best of the coal from the Pittsburgh seam, or than any northern coal, and in by-product ovens produce coke that is not excelled for any purpose by any coal mined in this country, and is equaled very seldom. Coal from several of these seams is shipped in great quantities without beneficiation and is lower in ash and sulfur than the best washed product from any seam mined in the north.

Jan 1, 1932

By Roswell H. Johnson

The principle of sliding or graduation in royalties is accomplished either by the block, period, cumulative, or class method. The block method calls for a very low royalty rate on all oil produced up to a certain amount. This amount would normally be that which is believed to suffice to repay the cost of the well. A higher rate would be charged after the well is making a profit. This method, common in many industries, is peculiarly inadaptable to any industry such as this where the productivity per day of the units gradually and inevitably decreases. This, for reasons given later, is because it forces an early abandonment of the well and so offends against conservation. In the period method, the royalty rate is changed by some definite amount when the well produces less than a specified quantity per day or other given unit of time. While simple to explain, it operates badly because a great deal is made to depend upon a small reduction in production, whereas the reduction as a matter of fact declines rather erratically owing to the exigency of lease management, connecting of tankage, and vagaries of the gaugers. These disadvantages are obviated by the cumulative method. In this method, all the production less than a certain amount per week has one rate of royalty, or none at all, and the oil produced in excess of that amount pays an additional rate of royalty. In the long run the calculation is probably no greater than with the period method, for simple tables will be published and printed in the oil papers that can be cut out, enabling quick readings to be made. Even without the table the calculation is easy with the few royalty rates, two or three, which would be used. In this method, the amount paid in royalty declines gradually, rather than suddenly as in the period method. The following reasons might be advanced for the adoption oi cumulative royalties: 1. To distribute the burden in accordance with the capacity to pay. This principle is a unique one in business, although familiar in taxation. This is because it does not distribute reward in proportion to efficiency.

Jan 1, 1916

By Bunting S. Crocker

PEBBLE grinding at Lake Shore is not a temporary wartime substitute. The tube milling plant, with a 1000 ton per day capacity, grinds a hard siliceous ore to 90 pct - 325 mesh. The plant, prior to using pebbles, was consuming 4.3 lb of 1 1/4-in. grinding balls per ton of ore, which amounted to 785 tons of balls per year. At September 1951 prices, $132.60 per ton, this steel cost amounted to, $104,400 per year, or $0.285 per ton milled. By the Lake Shore method of substituting screened rock for this steel, all of this cost is saved. This is one of the major economies in Lake Shore mill practice. Regardless of the ultimate price of grinding balls, a change, back to steel balls is not considered. The present pebble plant is more flexible than a steel ball plant and equally efficient. For example, if it is desired to change the size of grinding media, the pebble charge in any mill can be changed completely in 4 to 5 days, as against 76 days to change completely a 1 1/4-in. steel ball charge. To change pebble size it is necessary only to change two sets-of screens and clean out the rock feed storage bin. This will take 8 to 10 days as against 3 to 4 months to clean. out the customary supply of grinding balls kept on hand. Also it has not always been ' possible to purchase all desired sizes of balls at any price. In an analysis of savings effected by the use of the pebble mills, the flexibility of the Lake Shore grinding plant should be discussed, as it has a direct bearing on these savings. The plant has always used several units to handle tonnage rather than sending all the tonnage through a single unit. This principle may result in using small diameter mills, but no objection to that is seen. At no time has any advantage been found in cost per ton ground in large diameter mills. Both the capacity and the power of any mill varies as the diameter raised to the 2.6th power. Consequently large or small mills are equally efficient, and a plant should be designed to use as many units-or combination of units as is consistent with reasonable operating practice. Mills under 5 ft diam are harder to reline, etc. To define the case at Lake Shore, .2600 tons per day formerly were milled in seven 7x6-ft ball mills and twelve 5x16-ft (and two 6x16-ft) tube mills.* This gave an excellent test plant. and an extremely efficient-one. In this plant the ratio of ball mills to tube mills was 1: 2. When the much cheaper pebble mills were substituted for the tube mills, this. ratio -was changed to one ball mill to four pebble mills to take the greatest possible advantage of the cheaper operating mill, i.e., the pebble mill. This flexibility without loss in efficiency has been an important item in the cost savings. It is interesting to note that the use of pebbles for fine grinding was. proved first in the laboratory in a 12-in. ball mill. In fact, since 1934 all testing on -.8 mesh material has been done in this 12-in. mill. Scope of the Tests A paper on fine grinding at Lake Shore Mines was published in July 1940.1 This paper covered 7 years of intensive research on fine grinding as well as sizing methods and equipment, plant scale grinding tests on 5x16-ft tube mills with and without .grate discharges-both with 1 1/4-in. and 3/4-in. balls, the use of laboratory mills to evaluate plant changes, and several reports on classifiers and classification. In the following July the addendum report' was added in which the idea of series-circuit grinding was introduced, and the results of running five stages of tube mills and bowl classifiers were shown. Since 1940, the ball milling end of the plant has been altered extensively as a result of tests on the use of 3 1/2-in. rods in 7x6-ft mills and the use of the Tyler repulping screen with from 7 to 14 mesh screens. These tests are, lengthy and may be covered in a separate 'report later. The scope of this report is confined to ore ground by rod milling and ball milling until it passed through an 8 mesh Tyler Ty-rod screen. The -8 mesh screen undersize then was pumped to a primary bowl classifier in open circuit and the sands .from the bowl sent to the primary pebble mills, see Fig: 1. In the pebble mill circuit the ore is ground to 90 pct -325 mesh (24 pct + 28 microns) In studying the flowsheet, attention should be paid to the efficiency of the classification equipment used. The Tyler repulping screen is an efficient machine on the 8 to 10 mesh separation, and the bowl classifier is equally efficient at the 325 mesh separation. Efficient classification is a necessity for series-circuit stage grinding. The ore is hard siliceous porphyry, 60 pct SiO2, 80 pct insoluble. Its grindability at different. meshes has been shown near the top of 'the list in F. C. Bond's grindability tests' Lake Shore is not shown, but an adjacent-mine with identical ore, Wright-Hargreaves, is. Reasons for the-Changeover Since 1936 grinding balls have been rising steadily in price with no sign of stopping. For a mill that used 4.5 to 5.2 lb of grinding balls for every ton of ore ground this rise represented an alarming increase in grinding costs. In many cases the quality of the grinding balls fell off as the scrap steel became more difficult to obtain. The ratio of tube mills to ball mills increased with the use of the Tyler repulping screen in the ball mill circuit. Originally only 3.0 lb of balls per ton were used in the tube mills, and this

Jan 1, 1952

By F. Lynwood Garrison

There is probably no subject for study in the metallurgy of iron and steel of greater interest than the effect of manganese upon the properties of iron. Some of the peculiarities of iron and steel containing appreciable quantities of manganese were observed many years ago by Heath, Robert Mushet, and others; but it was not until the introduction of the Bessemer process, when a demand was created for large quantities of iron-manganese alloys, that such compounds of iron and manganese became articles of commerce. Since that time the demand for these alloys has steadily increased, the use of ferro-manganese not only becoming an absolute necessity in the ordinary Bessemer practice, but also essential to the manufacture of open-hearth, crucible steel and steel castings; in fact it is the only source of supply for all the manganese used in metallurgical opera-

Jan 1, 1893

GENTLEMEN Herewith are transmitted reports from the Treasurer and of the principal standing committees of the Institute. To these special reports members are referred for details as to the year's work. Despite the unfavorable business conditions obtaining throughout the year, the Institute was able to carry on its various activities without curtailment and without drawing on the surplus accumulated through previous years. In fact, small additions were made to the Life, Member¬ship and various other funds. It is highly desirable that such additions should continue to be made, especially to the Life Membership fund, for reasons reported last year. At present, money must be used from current receipts in order to enable the Institute to fulfill its obligations to those who on joining the organization commuted their dues by a single payment. In addition, with the passage of years the number increases of those who have paid dues forty years or more and who, by reason of age or dis¬ability, are unable longer to practise their profession. These men have supported the Institute through their active professional life and it would be a pity to lose them as members through resignation or for failure to keep up their dues. In accordance with the By-laws the Board has authority to advance such members, on application, to the Honor Roll of Senior Members and to relieve them from further payment of dues. It has been the policy of the Board to do this liberally, but to keep up this, as well as to meet other obligations, it is necessary for money to be provided. It has been estimated by the Treasurer that nearly $50,000 additional should be placed in the Life Membership fund as soon as possi¬ble to meet these obligations without using current income and to that end it is necessary, not only to avoid running behind currently but to earn, if possible, some surplus each year. The small amount transferred to the Life Membership fund from surplus this year was, as a matter of fact, made possible by certain members paying personally bills that were properly chargeable to the Treasury. Such generosity is common among those active in Institute work and probably no year would have closed with a surplus except for it.

Jan 1, 1923

By H. Reiss

The zone-melting process in which redistribution of solute in a solid bar is effected by the passage of a molten zone is considered mathematically. Simple approximate techniques are developed for computing the manner in which redistribution occurs as molten zones continue to pass. The introduction of the "zone-melting flux" provides valuable insight into the nature of the phenomenon, as well as a central mathematical theme in terms of which the process can be discussed. Curves are presented for typical and general cases. AN extremely efficient purification technique was described recently by Pfann.1 Known as zone refining, it consisted of the slow passage of a series of molten zones, produced by external heaters, through a long solid ingot of the substance to be purified. Equations were given for the maximum separation attainable, and a numerical computation method was described for obtaining the concentration in the ingot after a given number of zone passes. The present paper offers an interpretation of the physical nature of zone melting in terms of a transport process in which formal diffusive and convec-tive flows occur. This interpretation, in addition to providing insight into the physical nature of the process, also provides a basis for its mathematical treatment. From this basis, useful equations are developed for the solute concentration in the ingot as a function of the number of zone passes. These are applicable particularly where large numbers of passes are necessary and where numerical computational methods might be laborious. All considerations will deal with the limiting form of the process, described by Pfann,' in which: 1—Diffusion in the solid is considered negligible. 2—Mixing in the liquid is supposed, complete. 3—The distribution coefficient, k, measuring the ratio (at equilibrium) of solute concentration in the solid to that in the liquid is supposed, independent of composition. In general, this paper will be concerned with a bar of uniform (actually unit) cross section, ex- tending in the x-direction from x = 0 to x = L, where L may be infinite. Zone melting is a transport process, and as such must admit of interpretation in terms of a flux of transported quantity. However, the progress of operation is not measured in units of time but in terms of the number of completed zone passes. Consequently, the zone-melting flux will be a rate, per unit pass, rather than per unit time. The description of this flux and the examination of its properties is given below. Zone-Melting Flux Fig. 1 represents an intermediate stage of the nth pass. Concentration C is plotted against distance, x. The molten zone with its back at the point x and front at x + I moves in the direction indicated by the arrow. As it moves, it leaves behind the nth

Jan 1, 1955

By C. S. Allen

With increased coal production and mechanization of coal mines many transportation problems arise. The main objective is to bring the coal to the tipple or dump it as quickly as possible. Larger and faster haulage locomotives or two locomotives connected in tandem have been adopted to solve the problem. Motor equipment, gears and control systems of locomotives to be placed on these hauls are carefully studied to meet these requirements, by an analysis of motor characteristic curves with the corresponding tractive effort curves, in order to determine the correct load for maximum efficiency and to determine the approximate schedule. Control equipment is usually considered to be the controller and resistance. Sometimes accelerating curves are calculated in order to obtain smooth starting in the least possible time without slipping the wheels. Train control is very important, but why limit this to acceleration ? Deceleratien-or-retardation of the locomotive is a part of the train control and should be given as much consideration as the control for acceleration. Types or Braking Common braking systems for mine locomotives utilize screw-type mechanical brakes, dynamic braking and the air brake. For gathering and haulage locomotives, the srrew-type mechanical brake is regarded as standard. A brake of this kind cannot be applied without much effort and lapse of time. Motormen, like other people, follow the path of least resistance, and therefore have their brakes ready for instant application—which means that the shoes are virtually dragging. Even then, a motorman bucks and plugs the motors to gain time and avoid as much physical effort as possible. "Bucking of motors" consists in turning the reverse cylinder of the controller to parallel position corresponding to the opposite direction of travel while the locomotive is in motion, without applying power from an external source. When this occurs, both motors tend to act as series generators, because the armatures are revolving and there is residual magnetism in the field circuit. Owing to slight differences in motor manufacture, one of these will generate a slightly higher potential and will overcome the generated voltage of the second and tend to drive it as a motor in the reverse Direction.-This action retards the locomotive but is very severe on the segments of the reverse cylinder and on the motor commutators. "Plugging motors" is the application of power to the motors corresponding to the opposite direction of travel. In order to "plug" the motors it is necessary first to "buck,, them (which reverses the connections to the motors) and then to apply power. Theoretically, this should be done only in an emergency, but locomotives in mine service are frequently thus treated., Dynamic braking is retardation of the locomotive by the motors acting as generators, which take no power from the line.

Jan 1, 1942

By C. S. Allen

With increased coal production and mechanization of coal mines many transportation problems arise. The main objective is to bring the coal to the tipple or dump it as quickly as possible. Larger and faster haulage locomotives or two locomotives connected in tandem have been adopted to solve the problem. Motor equipment, gears and control systems of locomotives to be placed on these hauls are carefully studied to meet these requirements, by an analysis of motor characteristic curves with the corresponding tractive effort curves, in order to determine the correct load for maximum efficiency and to determine the approximate schedule. Control equipment is usually considered to be the controller and resistance. Sometimes accelerating curves are calculated in order to obtain smooth starting in the least possible time without slipping the wheels. Train control is very important, but why limit this to acceleration ? Deceleratien-or-retardation of the locomotive is a part of the train control and should be given as much consideration as the control for acceleration. Types or Braking Common braking systems for mine locomotives utilize screw-type mechanical brakes, dynamic braking and the air brake. For gathering and haulage locomotives, the srrew-type mechanical brake is regarded as standard. A brake of this kind cannot be applied without much effort and lapse of time. Motormen, like other people, follow the path of least resistance, and therefore have their brakes ready for instant application—which means that the shoes are virtually dragging. Even then, a motorman bucks and plugs the motors to gain time and avoid as much physical effort as possible. "Bucking of motors" consists in turning the reverse cylinder of the controller to parallel position corresponding to the opposite direction of travel while the locomotive is in motion, without applying power from an external source. When this occurs, both motors tend to act as series generators, because the armatures are revolving and there is residual magnetism in the field circuit. Owing to slight differences in motor manufacture, one of these will generate a slightly higher potential and will overcome the generated voltage of the second and tend to drive it as a motor in the reverse Direction.-This action retards the locomotive but is very severe on the segments of the reverse cylinder and on the motor commutators. "Plugging motors" is the application of power to the motors corresponding to the opposite direction of travel. In order to "plug" the motors it is necessary first to "buck,, them (which reverses the connections to the motors) and then to apply power. Theoretically, this should be done only in an emergency, but locomotives in mine service are frequently thus treated., Dynamic braking is retardation of the locomotive by the motors acting as generators, which take no power from the line.

Jan 1, 1942

By James W. Neill

Discussion of the paper of H. 0. Hofman, presented at the Canal Zone meeting, November, 1910, and printed in Bulletin No. 42, June, 1910, pp. 473 to 497. JAMES W. NEILL, Pasadena, Cal. (communication to the Secretary *) :-Professor Hofman's paper brings the art up to . date. As I was one of the pioneers in this business, I beg to give the following incomplete data regarding my efforts in this line. In the year 1883, while I was in charge of the smelting-operations at Mine La Motte, Mo., there was at the concentrator an unusually large production of a middle product, locally called "iron," which carried considerable values in nickel and cobalt, and which it was desirable, for this reason, to treat by itself. The works could not spare a furnace for the purpose; and to handle this product I improvised a "roast-hearth " from an old " lead-hearth." This was a small cast-iron furnace of the usual construction, about 2 by 4 ft. in dimensions, with a hollow cast-iron back, through which the wind circulated before entering the tuyeres. I had a cast-iron grate made to fit this hearth, and placed it flush with the lip, or apron, and above the tuyeres. On this grate, which had round holes about 0.25 in. in diameter, and a total surface of about 20 by 40 in., I roasted the nickeliferous pyrite product; starting the fire with kindling, then adding charcoal, and then gradually feeding the sulphides with a shovel, so as to cover the fire, choke down blow-holes, and get an even bed. Blast at a pressure of 3 or 4 oz. was supplied by a fail-blower. When a cake of roasted material had formed, it was removed with a steel bar, or fork, to the lip of the furnace, and thence into a wheel-barrow.. The fine material which had remained unmelted, but very hot, on top of the cake would promptly ignite when the cake was broken up and removed. The fire would then be covered with fresh material and * Received Aug. 29, 1910.

Apr 1, 1911