Search Documents

By AIME AIME

AN enthusiastic crowd, cheerfully confident that the upturn in the oil industry has arrived, gathered in Los Angeles on Sept. 29 for a Petroleum Division meeting arranged by the Southern California Section. The assembly room of the California Oil and Gas Association was the place of meeting. H. Norton Johnson was in the chair for the morning session, with about eighty members and guests present. Four papers were presented before lunch and a fifth, on electrical coring, was withdrawn as the work on which it was based is still confidential. Joseph Jensen read his contribution on the "Kettleman Hills Middle Dome Unit Plan" and, as he had an active part in framing the plan, his outline and discussion of it was authoritative and informing. J. H. Woods asked concerning the operation of the casing-head gasolene plant under the plan and was informed that one company would operate the plant and royalties would be paid participating companies

Jan 1, 1933

There are no data available of shipments until 1858, and then estimated, when railroad service became available. By reason of the iron made in the county, and the large amounts of salt, the tonnage used locally was quite large, and until 1860 these are estimated from the probable salt and iron production. After 1859 the tonnages shipped by rail are partly estimated from the total shipments of the Allegheny Valley Railroad from four counties. It is believed that the totals are below, rather than above, what the actual production was. While considerably larger for the same years than figures given by the Secretary of Internal Affairs and census reports, these data were always too low in those days, partly because of lack of facilities for gathering them, but more largely because of the strong prejudice existing in those days against furnishing such data to any governmental agencies.

Jan 1, 1942

By Terry Ramsey

INTRODUCTION The Cyprus Pima Mine is located 20 miles southwest of Tucson, Arizona and about fifty miles north of the Mexican border. The Cyprus Pima orebody was discovered in 1950. Feasibility studies were begun in 1952 employing underground development. Economic studies showed open pit operations to be feasible and stripping of overburden was begun in late 1955. The first ore was reached in October of 1956. A 3,000 tpd (tons per day) concentrator was completed and began operation January 1, 1957. From these beginnings, Cyprus Pima Mining Company has expanded into a plant processing approximately 54,000 to 56,000 tpd. Four expansions were required to bring the plant up to its present capacity. Each expansion incorporated what had been learned in previous operation of the plant. The first expansion was completed in August of 1963 doubling design capacity to 6,000 tpd. In reality, because of softer than average ore, capacity was closer to 8,000 tpd. Expansion II was completed in July 1966 bringing design capacity to 18,000 tpd. Expansion III followed immediately. Completed in the summer of 1967, this expansion increased the design capacity to 30,000 tpd. The actual dry tonnage of this portion of the operation in 1974 averaged 38,400 tpd, again, primarily as the result of treating softer than average ore. The latest expansion (Expansion IV), completed in December 1971 and utilizing a semi-autoge- nous grinding circuit, is located in a separate building (Mill II) approximately 200 yards southeast of the original mill (Mill I). Expansion IV was designed for 14,000 tpd, but after circuit modifications, averaged 16,500 tpd in 1974.

Jan 1, 1976

By L. D. Mullins, W. R. Bartlett, R. H. Barham, W. L. Wahl

This paper describes an electrical model and its applicution to the analysis of four reservoirs in Saudi Arabia. The model has 2,501 mesh points and represents 35,000 sq miles of the Arab-D member. Details of modeling such as mesh size, control problems and standards of performance in matching reservoir history are discussed. The particular performance match achieved for the Arab-D rnember is presented. Details such as permeability barriers, aquifer depletion and iwerference between oil fields are given. The performance match realized in the Abqaiq pool is presented in detail. INTRODUCTION The resistor-capacitor network and associated control equipment described in this paper comprise an electrical analog of a reservoir system. Similar equipment has been used to study the transient response of reservoirs for many years. The unique feature of the model and application to be described is the extremely large size of the model and reservoir system, and the detail observed in simulating the reservoir with the model. The Arabian American Oil Co. first became interested in analog computers for simulation of oil reservoirs in 1949. Since that time, several models have been developed, each more elaborate and refined so that the reservoir system might be more closely simulated. The current model is the latest in a series designed, built and operated by the Field Research Laboratory of Socony Mobil Oil Co. in collaboration with Aramco. It has been and continues to be used to study the regional performance of the Arab-D member limestone reservoir. The Arab-D member is one of the Middle East's most prolific producing horizons.. THE MODEL The theory of simulating a reservoir system with an electrical system has been presented in the literature.1-5 Therefore, this paper will not discuss the theoretical aspect of the problem except to point out the correspondence between the fluid system and electrical system, as shown in Table 1. In general, the complete model is made up of input devices, output devices, central control and a resistance-capacitance (RC) network. At times, the RC network alone is referred to as the "model". However, it should be evident from the text which meaning is attached to the word "model". A discussion of the equipment follows. THE RESISTANCE-CAPACITANCE NETWORK The RC network consists of 2,501 capacitance decades interconnected through 4,900 resistance decades. The components are arranged to form a rectangular network of 2,501 mesh points in a 41- X 61-mesh array. Imposing the mesh grid system on the continuous reservoir system divides the reservoir into discrete areal segments. These discrete segments may be of various sizes. More precisely, the mesh size need not be uniform throughout the model. The RC network is fabricated in two sections which are connected at the top. An inside view of the "tunnel" formed by the two sections is shown in Fig. 1. The height and width of the tunnel are shown in the figure. Numerals appear along the bottom and along the back opening of the tunnel. These numbers denote the x and y co-ordinate positions of mesh points. Fig. 2 presents a rear view of one-half the model. The length dimensions of the model, as well as a rear view of the capacitor decades, are shown in this figure. The control dials used in adjusting the resistance and capacitance values on the model can be seen in the enlarged portion of the model shown in Fig. 3. The electrical capacity at any mesh point can range from 0 to 1.0 microfarads set to the nearest tenth of a microfarad. The electric resistance connecting any two mesh points can range from 0 to 9,990,000 ohms set to the nearest 1,000 ohms. External capacitors may be added to any or all mesh points if the need arises. The values of electrical resistance and capacitance are adjusted manually by manipulating the two types of decade units. INPUT EQUIPMENT A considerable quantity of equipment is used to control the input to the RC network. These input devices are

By O. L. Kowalke

THE measurement and control of temperatures have assumed positions of great importance in many industries. The manufacturers of byproduct coke and carbureted water gas find that proper temperature control helps to produce a better product and economizes in the use of raw materials. In the manufacture of glass, enameled ware, brass, and high-temperature refractories, temperature control is now regarded as being coordinate in importance with the control of materials used. To control such processes as malleablizing cast iron, and hardening, tempering, and annealing of steel in a manner to meet exacting market requirements has, within recent years, involved the installation of large and expensive pyrometer equipments. In many of these installations, it was necessary not merely to measure but also to record the temperatures over a period of time and thus obtain a record of the entire heat treatment and an effective check on the workmen in charge. In view of the importance of temperature measurement and control in such a wide variety of industries and the necessity for proper supervision of the installation and operation of the outfits, the following questions may be pertinent: What instruction is offered by the engineering colleges and what departments in the colleges are responsible therefor? The latest available catalogs of ten prominent engineering colleges east of the Mississippi River showed courses in high-temperature measurements given by the departments of physics. These courses, in general, were described as comprising classroom and laboratory instruction in the theory of high-temperature measurements, together with exercises in the calibration of the various devices used. In some cases it was stated that consideration would be given, in the courses, to the practical applications in the industries. In only one. college was the course required of all engineering students; in most colleges it was optional; in a few colleges, it was required only of certain groups. In colleges offering a course in metallurgical engineering, instruction in pyrometry was always given in connection with metallurgical laboratory work. The students in ceramic,

Jan 8, 1919

By H. H. Stoek, G. W. Harries

The term " Anthracite Coal-Field " is generally used to refer to a comparatively small territory lying in the eastern-central part of Pennsylvania. This territory includes about 3,300 sq. miles of area, located chiefly in five counties in which anthracite-mining is the dominant industry. Although an area of 3,300 sq. miles is embraced in the region, less than one-fifth of this area, or only 484 sq. miles, is underlain by workable coal-seams. Moreover, this prorluctive portion is not a continuous area, but consists of a number of detached basins. These are known as the Northern, containing 176 sq. miles; Eastern-Middle, containing 133 sq. miles; Southern, containing 181 sq. miles; and western-Middle,containing 194 sq. miles. From the standpoint of business and trade, the region is divided into three districts, known as (1) the Wyoming, which includes the Northern field and the small Bernice basin; (2) the Lehigh region, which includes all of the Eastern Middle field and that part of the Southern field east of Tamaqua; and (3) the Schuylkill region, which includes the WesL ern-Middle field and that part of the Southern field west of Tamaqua. The relative commercial importance of these districts at the present time is shown by the coal-shipments as given in the following table :

Jan 1, 1904

By Howard Evans

Moderate but substantive gains were recorded in 1972 in the minerals processing industry. In the area of mill design, a number of large plants under construction during the past two to three years were tuned up and went into production. The application of operating controls has also made some significant strides. Progress here has been made in the areas of on-stream particle size analysis, on-stream x-ray analysis, slurry transportation, tripper control, flotation reagent control and digital control of grinding circuits. The major contributions to improved equipment are coming from smaller specialized equipment makers.

Jan 2, 1973

By Frank Woolley, John F. Elliott

The high-temperatzrre solulion calorimeter has been modified and an extension dynamic analysis of i/s transient behavior has provided an improved basis for interpretation of the experimental data. The partial molar heats of mixing, Him, of aluminum, copper, and silicon in the corresponding binary liquid-iron alloys haz,e been measured directly at 1600°C. The resulls in kcal per g-alom are: THE high-temperature1,2 solution calorimeter was planned and designed to obtain directly the partial molar heat of solution of solute elements in a variety of liquid metals that might serve as solvents. Results obtained in the temperature range of 1000° to 1200°C were described in the two earlier publications. However, a long-term goal in the program has been to obtain measurements at 1600°C of the heats of solution of elements in liquid iron. Hence, subsequent to the work last reported,2 and based on the experience of the first two studies, the calorimeter system has been modified and operated at 1600°C to obtain measurements on the Fe-Si, Fe-A1, and Fe-Cu systems. This paper reports the results of the work. THE MODIFIED SYSTEM It was clear from the earlier results that the most precise measurements can be obtained with the high-temperature solution calorimeter when the solution time is less than approximately 30 sec. This can be achieved only when the bath temperature, Tb, is above the melting (liquidus) temperature of the solute material being dropped. A second point of importance is that the refractories used earlier liberated considerable water so that, although the oxygen potential of the atmosphere in the system was satisfactory for work with nickel and copper, it was too high for work with iron, silicon, and so forth. Third, for work at 1550" to 1650°C, an improved temperature-sensing unit is needed. The modified calorimeter in its latest form is shown schematically in Fig. 1. The refractory brick and the Kanthal-Super heating elements which formed the furnace for heating the solute addition have been replaced by a smaller resistance-heated tube furnace which is insulated with bubble-grain alumina. A more elaborate gas purification system was installed to maintain a satisfactorily low oxygen potential in the atmosphere of the calorinieter chamber and of the solute addition furnace. As was the case in the earlier work, at the beginning of a run the calorimeter chamber is evacuated and then filled with purified argon so that a total pressure slightly in excess of 1 atm is maintained during the run. When either of the furnaces within the enclosure attains a red heat, 6 pct H2 is added to the atmosphere. Throughout the run, gas from the calorimeter is circulated through a de-oxidation system at the rate of approximately 5 standard liters per min; the changeover time for the gas within the calorimeter enclosure is approximately 1 hr. The essential stages of the deoxidation system are: a copper furnace at 600°C, a drying tube of anhydrite, and a titanium furnace at 800°C. The oxygen potential of the gas stream in the purification system can be monitored at several points by a stabilized zirconia oxygen cell. This cell is invaluable in detecting the development of leaks in the container vessel and the gas circulating system. The installation of the solute-addition furnace allowed either of two types of temperature-sensing units to be mounted on a water-cooled probe. The first was a small optical device using a silicon diode that was

Jan 1, 1968

By C. J. Delisio

The basic concept of tunnel boring has not changed since the late 1800's. R. Stanley of Great Britain obtained a Canadian patent as early as December 1891. Mr. Stanley's machine was a device that consisted of a rotating wheel equipped with drag-type teeth; it had a means of thrusting the cutterhead against the face or heading; it had a means of clamping or gripping the machine in its bore; it had a means of collecting and depositing the cuttings into a screw-type conveyor located near the invert of the tunnel. It even had a means of varying the speed of the forward motion of the machine to suit different hardnesses of rock encountered. This description essentially fits the latest tunnel-boring machines being built today. In short, there has been no significant advance in the basic concept in 70 to 80 years. It may well be that no significant change can be expected for some time into the future. Today's machines, while still basic in concept, offer many advances aimed at faster tunneling. Among these are 1 ) improved cutters, 2) guidance and steering devices, 3) dust-control devices, and 4) mechanisms to aid in installing tunnel supports. CUTTERS The most important part of a hard-rock tunnel borer is the cutter. If the cutter can cut the rock, it is a boring machine. If the cutter cannot cut the rock, no other part of the machine can. When Jarva, Inc. decided to build a machine, the first problem was to find a good cutter. In our search, we looked at most of the cutters on the market. We selected Reed Drilling Tools' cutter because the design of their cutter was aimed at hard-rock tunneling. We feel that they build the best cutter available and provide the best possible service to their customers. As tunnel-boring machine design advanced, the transition from drag bits to roller bits was natural because harder formations required a roller bit, and it is the goal of all mole users to bore harder formations. Roller bits

Jan 1, 1970

By R. Q. Shotts

This paper is a review of recoverable reserves of bituminous coal in the Southern Appalachian area, according to the latest published estimates. A few comparisons are made, some apparent trends are discussed, and some comments are made regarding the limitations of present estimates. The definition of Southern Appalachian area used in this report is somewhat arbitrary. It includes all the bituminous coal deposits of Alabama, Georgia, and Tennessee. All of West Virginia has been excluded. The East Kentucky and Virginia counties included were selected in connection with a literature study the writer made in 1959 of possible coal supply areas for the Tennessee Valley Authority. The selected counties were considered to be the only ones from which TVA might expect to obtain coal. The availability of coal from some of these counties is doubtful, but no other East Kentucky counties were considered more than remote possibilities. With these limitations, the Appalachian area covered is that from which producers of electric power and steel and commercial coal users, located in the Southeastern U. S., may expect to obtain their supplies of coal. Of course, it is recognized that coal from the eastern interior fields is also available to many of these same organizations. RANK AND QUALITY OF THE COALS Practically all the coals in the Southern Appalachian region are of high volatile A bituminous rank. An occasional sample indicates a slightly lower rank, but such samples may be oxidized or otherwise not representative. Some thin beds in Lookout Mountain and Sand Mountain in Alabama and Georgia, are low volatile bituminous coals, but they have not been mined extensively in modern times. There is a possibility that some of the deeper beds along the southeastern edge of the Warrior field of Alabama are near the Low-medium volatile bituminous dividing line. The Sewanee bed and some other minor ones of the Southern Tennessee field, some of the lower beds in Virginia, many beds in Sand and Lookout Mountains in Georgia and Alabama, one or more beds in the Coosa field, possibly some lower beds in the Cahaba field, and most of the beds along the southeastern edge of the Warrior field and the southern end of the Sequatchie anticline of Alabama, are of medium volatile bituminous rank. The quality of the Southern Appalachian coals is highly variable. Some of them, particularly such prevailingly thin ones as the Black Creek bed of Alabama and the Straight Creek bed of Kentucky, are unusually low in mineral matter— probably the lowest in the U. S. With the exception of certain beds and local areas, Alabama and East Kentucky coals probably have as low average ash and sulfur content as can be found in any sizeable coal area in the country. The sulfur content of Southern Appalachian coals is also variable, but few beds are consistently high in sulfur. In Alabama, sulfur generally increases from southeast to northwest across the Warrior field, but this trend is not quite as clear in the other states. A few beds in Northern Tennessee are prevailingly high in sulfur. All Southern Appalachian coals are potential coking coals if they can be prepared to meet chemical requirements. Only a comparatively small part of the medium volatile A bituminous coal, but most of the medium volatile bituminous coal mined is actually used for coking purposes. An estimate of reserves of coking coal under the requirements of present practice, could be compiled comparatively easily, but this probably has never been done. The reserve of coal that can be coked as an ingredient of a suitable blend is probably many times the size of the reserves of coal that will yield suitable blast furnace and foundary coke without blending. WHAT CONSTITUTES ECONOMICALLY RECOVERABLE COAL RESERVES? When one first realizes the vast extent of the coal-bearing rocks in the Southern Appalachian area, (see Fig. 1) the thought is likely to occur that the supply of coal is inexhaustible. This is particularly true on realizing that in some of the basins of thicker coal-

Jan 1, 1962

By Basil B. Zavoico

Production of crude oil in the U. S. S. R. during 1939 is estimated at, 226,111,000 bbl., as compared with 219,778,000 bbl. in 1938, an irlcreasc of 2.88 per cent but some 6.00 per cent under the planned output. During the past year a major readjustment took place in Russian oil fields, with the Grozny district falling into the third place, its former place having been taken by the fields of the Maikop-Kuban area of northwestern Caucasus. Production continued to grow in the Ural-Volg:t district and further large increases in this province in the coming years are certain. The drilling operations continued to be most unsatisfactory, falling far behind the plan, possibly as much as 25 per cent undvr the set objectives, and thereby interfering with the production plans, mora particularly since the Soviet oil industry is still based primarily upon the production from the naturally flowing wells without any proration whatsoever rather than upon stabilized production from either prorated oil wells or those operated with various mechanical lifts. The year 1939 started with the fulfillment of the drilling programs to the extent of about 90 per cent, but the situation rapidly deteriorated arid by the second half drilling programs were being fulfilled only to the extent of 60 per cent or less. Such breakdown in drilling operations was possibly due to poor equipment, which has not been able to stand increasing demands upon it, and this is substantiated by the rccent orders plaeed in the United States by the Soviet Government for some 60 drilling rigs of the latest design. Production Baku District.—-The fields of the Apshcbron Peninsula (Baku district) made a notable progrress during the past year and were able slightly to increase their production, to 166,000,000 bbt. as compared with 164,692,-000 bbl. during 1938. The c.rnphasis of production in the Baku district remained on the flowing wells, about 20 per cent of the total number of wells flowing about 70 per cent of production. During 1939 some 550 wells were complr.tcd in the Baku district with active rigs averaging

Jan 1, 1940

By Basil B. Zavoico

Production of crude oil in the U. S. S. R. during 1939 is estimated at, 226,111,000 bbl., as compared with 219,778,000 bbl. in 1938, an irlcreasc of 2.88 per cent but some 6.00 per cent under the planned output. During the past year a major readjustment took place in Russian oil fields, with the Grozny district falling into the third place, its former place having been taken by the fields of the Maikop-Kuban area of northwestern Caucasus. Production continued to grow in the Ural-Volg:t district and further large increases in this province in the coming years are certain. The drilling operations continued to be most unsatisfactory, falling far behind the plan, possibly as much as 25 per cent undvr the set objectives, and thereby interfering with the production plans, mora particularly since the Soviet oil industry is still based primarily upon the production from the naturally flowing wells without any proration whatsoever rather than upon stabilized production from either prorated oil wells or those operated with various mechanical lifts. The year 1939 started with the fulfillment of the drilling programs to the extent of about 90 per cent, but the situation rapidly deteriorated arid by the second half drilling programs were being fulfilled only to the extent of 60 per cent or less. Such breakdown in drilling operations was possibly due to poor equipment, which has not been able to stand increasing demands upon it, and this is substantiated by the rccent orders plaeed in the United States by the Soviet Government for some 60 drilling rigs of the latest design. Production Baku District.—-The fields of the Apshcbron Peninsula (Baku district) made a notable progrress during the past year and were able slightly to increase their production, to 166,000,000 bbt. as compared with 164,692,-000 bbl. during 1938. The c.rnphasis of production in the Baku district remained on the flowing wells, about 20 per cent of the total number of wells flowing about 70 per cent of production. During 1939 some 550 wells were complr.tcd in the Baku district with active rigs averaging

Jan 1, 1940

By Edward H. Robie

PROBABLY nowhere in the United States or its possessions is mining development more active at present than in the Philippine Islands. Only a few years ago only one company was of any importance, the Benguet Consolidated. Now, five companies are paying dividends, five others have reached the producing stage, some seven others may produce this year, and a score or so are being actively developed. Gold production in 1933 was valued at about $8,000,000, last year at about $11,000,000, and this year an output valued at about $17,000,000 is envisaged. At the beginning of 1934 about 1750 tons of ore was being milled daily; at the end of the year, the tonnage was approximately 3400. In 1933 there were only thirteen Institute members in the Philippines; a year ago there were 27, and now there are 46. About fifteen thousand amen were employed in the mining industry last year, with mine payrolls amounting to $3,500,000. An immense amount of new machinery has been required. One difficulty has so far hindered gold-mine development to some extent-lack of adequate power. Each company therefore finds it necessary to generate its own power, and for this purpose diesel engines are generally adopted.

Jan 1, 1935

By AIME AIME

PETROLEUM technology was the sole subject of discussion at the meeting of the Petroleum Division at the Baker Hotel, Dallas, Texas, Oct. 6-7, except for the brief talks by President Becket and Secretary Parsons at the dinner on Friday evening. Even on this occasion, following the scheduled official features, it was in order to talk "shop." W. E. Wrather and E. A. Stephenson, respectively Chairman and Secretary of the Division, had planned for a meeting of this nature and by preference, apparently, the 122 who registered fell in with the scheme wholeheartedly. Not because the competent local committee had not provided for it, but by choice, the members just did not sign up for entertainment or field trips, but did attend largely the three technical sessions and engage in earnest discussion of the approximately dozen excellent papers. In this connection, and without question, the high lights of the meeting were the papers by Morris Muskat and R. D. Wyckoff, and Prof. W. K. Lewis. The former, entitled, "A Theoretical Analysis of Waterflooding Networks," had been entirely demathematized by the authors for presentation at this and the Los Angeles meetings; the author of the latter, which was on the "Physical-chemical Relationships of Hydrocarbon Gas-liquid Mixtures at High Pres¬sures," had airplaned to Dallas in the company of Dr. H. D. Wilde from Chicago in order to present his paper at the final session on Saturday morning.

Jan 1, 1933

By Herman Van Fleet, Frederick W. Neil, O&apos

The object of this paper is to describe the present status and possil~ilities of liquid oxygen as an explosive based upon the investigations, research and practical work of the Ingersoll-Rand Co., and of the Air Reduction Co., from early in 1922 to date. The following work was done. 1. A study of the history and physical theory of L. 0. X. as an explosive. (No attempt will be made in this paper to give the history or theory, as this has already been covered by the literature on the subject.) 2. An investigation of the use and the practice with L. 0. X. in the iron mines of Lorraine where L. 0. X. has its largest application in Europe. Although L. 0. X. is extensively employed in the iron mines of Lorraine, many of the mines using it exclusively, and blasting with it a total of approximately three million tons of iron ore per year, the fact that the mining practice in Lorraine1 is to drill comparatively shallow holes and blast only a few holes at a time, renders the data obtained there of very little value in estimating the possibility of replacing dynamite with L. 0. X. in American mining methods. In fact, in the iron mines in Lorraine, L. 0. X. replaced black powder, or its equivalent. 3. Laboratory research work on properties of absorbent materials. 4. Work in the Bureau of Mines explosive laboratory at Pittsburgh, Pa., on the properties of L. 0. 3. cartridges. 5. Practical work underground with L. 0. X. cartridges in the Kitherbee-Sherman iron mines at Mineville, N. Y. 6. Practical work in the quarries of the Calcite Quarry Co., Myers-town, Pa. 7. Practical blasting in several quarries and open-pit mines.

Jan 1, 1927

By T. A. Rickard

The notion prevails that writing is a knack, that the skilful use of the pen is a gift of nature. This is an error. Dogberry may be responsible for it; he said: "To be a well-informed man is the gift of fortune, but to write and read comes by nature". Because Dogberry said it, we may be sure that Shakespeare thought otherwise. Ability of any sort may be partly innate, but my own observation and experience lead me to conclude that most of the easy writers have become so by constant practice. As I recall the names of men successful with the pen, I remember that most of them have written a great deal and have taken particular pains to improve their style. The suggestion that proficiency in the difficult art is a happy accident provokes a sardonic smile. The larger part of the great writing in our literature is the result of persistent effort. An easy fluency has been the undoing of many; their flamboyant and fantastic scribbling has proved as perishable as froth. This criticism applies to technical writing also; in order that a technical description or discussion may hold the interest of the reader, at least long enough to cause him to read it to the end, the writing must be done carefully and systematically; otherwise it will fail in its purpose of conveying information. Clearness is absolutely essential. "It is not enough to use language that may be understood; it is necessary to use language that must be understood."* The purpose of writing, at least of that which is meant to be read by others, is not only to express ideas but to communicate them. Lack of perspicuity may prove as %ad as

Jan 1, 1931

By A. Aly Selim

A computer model was developed to calculate the fragmentation cost for in situ leaching operations as a function of the blast design and deposit parameters. The model is based on blasting an ore zone only or an ore zone plus overburden by either a coyote blast or a vertical blasthole system. The model calculates the blast design parameters and the fragmentation cost based either on a user input powder factor value or on a powder factor calculated by the model as a function of the overburden height and the ore zone thickness. Examples of blast design parameters calculated by the model are the number and spacing of blastholes for a vertical blasthole system and the number and spacing of crosscuts for a coyote system. The model also calculates the total amount of explosives, the detonating cord length, and the number of primers. The cost of blasthole drilling can be calculated by the model based either on purchasing and operating a drill or on a user input value of the contracted cost of drilling. Application of the model to an example ore deposit showed that the vertical blasthole systems were more economical than the coyote system when there was no overburden and the deposit had an average ore thickness less than 45 meters. With no overburden and ore thickness greater than 45 meters, the vertical blasthole system was either more or less expensive than the coyote system depending on the number of levels used in the coyote system. With overburden, the coyote system was less expensive than the vertical blasthole system for blasting either the ore only or the ore plus the overburden. A coyote blast will usually produce larger particle sizes than a vertical blasthole system. Larger particle sizes can result in lower copper recoveries so that a less expensive coyote blast may not improve the overall economics of an in situ leaching operation. Blasting the ore zone only was generally less expensive than blasting the ore plus the overburden by either blasting system. Also, for the example considered, the coyote system costs were less sensitive to changes in overburden thickness and powder factor while the vertical blasthole system costs were less sensitive to changes in ore thickness.

Jan 1, 1977

By E. N. Silverman

Mixtures of' MnS, ZFeO-SiO,, ZMnO.SiO, FeO, and MnO were prepared synthetically and used to study the planes ZFeO. Si0,-ZMnO.SiO,-MnS, FeO-MnO-MnS, and Fe0-MnO.Si0,-MnS in the quaternary system. Because the oxides and silicates studied flux MnS, inclusions in this system are partly liquid during rolling. Also, oxygen can modify subsurface inclusions through the reaction MnS + FeO—FeS + MnO during the soaking of ingots and the reheating of blooms and billets. NONMETALLIC inclusions in steel have long been a subject of study and conjecture because the properties of many steels are known to be affected by the the kind and amount of inclusions present. In free-machining steels, the type of inclusion present has a direct bearing on their machinability; in other steels, cleanliness is important and metallurgists direct their efforts at reducing the amount of non-metallic inclusions. Thus, the accumulation of knowledge about the formation and behavior of inclusions during all stages of steelmaking and processing should aid in improving the quality of steels and decreasing the production costs resulting from rejections. Previous studies of inclusions have contributed greatly to our understanding. The investigators have generally examined inclusions in finished steel. Boulger, Moorehead, and Garvey1 found that in Bessemer steels, low silicon contents results in globular sulfide inclusions with attendant high machin- ability ratings. Van vlack2 also found that low silicon contents favor inclusion morphology that contributes to high machinability ratings. Boquist and Stoll* found that silicon content affected sulfide inclusions and machinability of blooms, billets and bars more than did the finishing temperature in the range between 1775° and 2075°F. Carney and Rudolphy3 studied the distribution of sulfur, manganese, silicon, and carbon in a commercial ingot of resulfur-ized steel and found that silicon was concentrated near the bottom. This helped to explain why bottom cuts had poorer machinability. Klinger and Koch4 developed techniques for extracting inclusions from steel, and the technique devised by Gurry, Chris-takos, and stricker5 for extracting carbides can also be adapted to the study of inclusions. A different approach to the study of inclusions in steel consists of synthesizing the constituents that form inclusions and determining the phase eauilibria in the system that contains the constituents. The resulting phase diagrams can then be used to determine the effect of the various constituents upon each other. In this way, it becomes possible to under-

Jan 1, 1962

By R. P. Rothwell

THE milling of silver ores has arrived at a great degree of perfection in the mining districts of our Western States and Territories, and I have thought the record of the practical results obtained at the present time, in a few of the principal districts, would prove of value and interest to many of our members, both at home and abroad. An American silver mill is composed, in descending order from where the ore is dumped, of: 1st. A rock-breaker, usually of the Blake or Alden pattern ; 2d. The battery of stamps, the number of which varies from 5 to 120, generally in batteries of 5 or 10 heads, so arranged that a single battery may stand while the others are running; 3d. The tanks where the crushed ore settles (if it is a wet stamping-mill), or of a drying-floor if the crushing is done dry; 4th. Amalgamating pans ; 5th. Settling pans ; 6th. Agitators or pans in which mercury escaping in the tailings is caught; 7th. Blanket sluices, over which the tailings run, and where mercury and unamalgamated sulphides are saved. A reference to the engravings (see plate), which show one of the latest forms of an 80-stamp silver-mill run by a turbine water-wheel, will show clearly the arrangement of the several parts. THE ONTARIO, UTAH, SILVER MILL. One of the best examples of a silver-mill, and at the same time one of the most successful concerns in the West, is the mill of the Ontario Silver Mining Company, near Salt Lake, in Utah. This mill treats the ore from the Ontario mine, ore which at present is very base, being composed of zinc, lead, and silver sulphides and silver chloride in a quartz gangue. This ore has become baser as the mine attained greater depth, though the vein holds its own, or rather increases, both in thickness and richness. The mill is man¬aged in a skilful and economical manner, though the necessity for * Read at the Montreal meeting, September, 1879.

Jan 1, 1880

By H. H. Dievendorff, F. W. Hertel

The method of drilling deep wells into the earth for the recovery of oil and gas is beset with many hazards. This is especially true in the Ventura Avenue field, which has the distinction of being the hardest field in California in which to complete a deep well. The hard, shifting and squeezing formations must be penetrated to great depths in the face of tremendous gas pressures. This field presents problems that keep the operators abreast with all of the latest developments in oil-field tools and machinery and in oil-well drilling practices. Equipment must be strong, and adapted to deep-well drilling and the handling of long heavy strings of casing. High-pressure sands require the utrnost care and attention of the operators and no chances can be taken, since a serious blowout may cause the loss of a well that has cost months of labor and expense. Equipment must meet these requirements or be discarded. Although the deepest wells in the world are not in this field, nor hav:. the longest strings of casing been set, nevertheless, the consistency with which deep wells are drilled and long strings of casing are set places the Ventura Avenue field foremost, in this respect, among the oil fields of the world. The V'entura Avenue field dors claim the deepest commercial oil-producing well in the world, in the Shell Co. of California's "Edison" No. 18. This well was drilled 7015 ft. and came in flowing 3280 bhl. of oil per day. This field also claims the deepest average depth of producing wells in that its Ill producing wells average 5676 ft. in depth. Of these 111 producing wells, 50 arc 6000 ft. or deeper, and 16 are 6500 ft. or deeper. Also, of the 111 producing wells 100 arc flowing, and 11 arc pumping wells. This paper is intended to set forth the methods used in the drilling of deep wells with rotary tools and the handling of long heavy strings of casing in the Ventura Avenue field.

Jan 1, 1928