Search Documents

By Norman L. Wimmler, H. G. Iverson, S. Ricker, P. E. Oscarson, S. H. Lorain

THIS paper has been prepared with the principal objective of recording the results of the Bureau of Mines exploration of five major clay deposits in the Western Region. It is based mainly on data contained in unpublished Bureau of Mines reports. Acknowledgment is made to the Federal Geological Survey for its cooperative work with the Bureau of Mines, to the various State geological and mining departments, and other State and local agencies. CLAY EXPLORATION BY THE BUREAU OF MINES Much has been written and published on clays and clay deposits relating to their refractory, ceramic, and other qualities but such literature is lacking in analyses of the available alumina content of the clays and provides little indication of their possibilities as a source of alumina. With this new objective in view, a great many of the known clay deposits were reexamined and new ones discovered. The Bureau of Mines made preliminary examination of numerous areas in the western United States. Five of those most favorably indicated were systematically drilled, and in each a large amount of high-alumina clay has been found. These five major projects are Molalla and Hobart Butte, in western Oregon; Cowlitz-Castle Rock, in southwestern Washington; Lone, in California; and the Olson-Troy area in Idaho (Fig. I). Preliminary scout drilling was done in the Stockton deposit at Coeur d'Alene, Idaho; the Whiteware deposit near Lewistown, Mont.; and 13 areas in the Spokane or eastern Washington region, where the most favorably indicated area, known as the Excelsior, is now being drilled more systematically. Preliminary drilling was undertaken in numerous areas adjacent to the major deposits and others more remote. As a result, large additional clay possibilities were found. THE CLAY DEPOSITS The clay deposits under consideration are of the sedimentary or transported types, parts of which have been altered further by the agencies of weathering, ground water, or hydrothermal action. There are extensive deposits of residual clays in northern Idaho and in eastern Washington, but they have been found to be low in the available alumina and to contain much free quartz, mica, and unaltered feldspar. To be of value, they must first be subjected to beneficiation to remove these gangue minerals. The sedimentary clays have been derived largely from the decomposition, erosion, and transportation of granites, gneisses, schists, and basalts. At Molalla, some

Jan 1, 1944

By Wittenau, E.

OPERATION of a pilot mill of 100 tons' daily capacity during 1930 and 1931 proved that the copper minerals of the Colorado and Clay sections of the Morenci ore body could be successfully concentrated by the flotation process. Economic conditions caused postponement of further testing work until late in 1938 when the former No. 6 Concentrator at Morenci was converted into an experimental mill of 1500 tons' daily capacity which was known as the Test Concentrator. The Test Concentrator began continuous operation on April 3. 1939, using such crushing and grinding equipment of the No. 6 Concentrator as was appropriate. Modern classifiers and certain flotation machines were installed and later other types of flotation machines, a large grate-type grinding mill. mechanical screens, a short-head cone crusher, and a disk filter were added to the test equipment. Operation was uninterrupted until Dec. 31, 1941.

Jan 1, 1942

By Burt C. Mariacher

To note that environmental considerations had a major im¬pact on the minerals processing industry in 1971 would be something less than a profound observation. The degree of its importance was demonstrated by MBD when it established the Environmental Committee as a new unit committee within the Division to achieve greater participation in exchange of information relating to the technologies and problems involved. It is appropriate and necessary to devote special attention to this timely aspect of minerals processing, as its influence penetrates the research, engineering and operations of almost all unit technologies that comprise minerals processing. The pollution abatement aspect of this industry has been such a dominant factor in recent years there is reason to wonder whether progress in unrelated technologies has been curtailed. Perhaps so, to some degree, but unit committee reviews presented in this article suggest rather that it would appear to have served as a catalyst for accelerated progress in development of new methods and improvement in more conventional ones. Present concepts regarding primary metal or mineral recovery and by-product potential may change considerably as a result of improved technology in waste product treatment.

Jan 2, 1972

By Heinrich Ries

Fullers' earth is a clay-like substance, which has the property of decolorizing or clarifying oils. An ultimate chemical analysis shows it to differ from most ordinary clays in having usually a high percentage of combined water and a low amount of alumina. There is probably a large amount of hydrous silica present. Fullers' earth possesses little or no plasticity, and in order to work properly has to be ground very fine. A chemical analysis is of little value at present in determining its quality; only a practical test suffices. Up to about two years ago all of the fullers' earth used in this country was imported from England; but about that time deposits were discovered in Florida, "† and since then rumors of its occurrence have been coming from all parts of the country. Next to the Florida deposits of fullers' earth, those of South Dakota are the most extensive thus far discovered in this country. The earth was first discovered near Fairburn, Custer county, and other deposits have since been prospected at Argyle, Minnekahta and other localities. Fairburn.—One of the first deposits located and opened up is five miles southeast of Fairburn, Custer county. The mine is a mile from the Fremont, Elkhorn and Missouri Valley Railroad, and the section exposed shows, beginning at the top: Feet. Micaceous sandy clay,......... 6 Fullers' earth,..........9 Micaceous sandstone,......... The fullers' earth passes upwards into the sandy clay, but in its purer portions it is a yellowish, gritty clay, with a somewhat

Jan 1, 1898

By H. E. Mills

THE local auditorium of a little Alabama mining town was crowded with expectant men, women and children, as the bulletin board had announced the addition of visiting entertainers to supplement the local talent and motion pictures which usually made up the program of the regular monthly safety meeting. In the audience, near the stage, sat a group of bright-faced boys in boy scout uniforms, discussing the picture just completed. As the lights flashed on a crash and scream was heard from the outside, a shrill whistle and word of command from the scoutmaster, and five of the scouts ran out of the hall, while the mine super-intendent stepped on the stage and requested everyone to keep their seats. The scouts returned, three of them carrying a limp figure in their arms, while the other two cleared the doorway and aisle of excited spectators. They marched to the stage and, placing the apparently badly-injured boy on the floor, proceeded to give an expert demonstration of first aid to the injured. The scoutmaster then explained to the audience that the whole affair had been arranged for their benefit, and invited the local first-aid men to come up on the stage to examine and criticize the boys' work. This gave an opening for several talks on the value of first-aid training and accident prevention, which is the main object of the monthly meetings. This demonstration was given by the first-aid team of Troop One, and the entertainment was provided by members of Troop One and Twenty-eight of the Bir-mingham Scout Council, organized by the writer for the purpose of promoting interest in the welfare and safety meetings in the mining villages of the State. During the past year they have visited a number of such meet-ings and presented programs similar to the one men-tioned above. However, in order to assure a good attendance, entertainment features must also be pro-vided, and the serious part of the evening program was interspersed with excellent vocal and instrumental mu-sic, dancing and novelty acrobatic acts furnished by the visiting scouts. In addition to the numerous first-aid teams of the Birmingham Council, there are hundreds of scouts scat-tered throughout the mining district whose knowledge of first aid, safety first, life-saving, personal health and public health are a constant source of protection to their community. All of these subjects are covered by merit badge pamphlets and are required of an eagle scout.

Jan 2, 1927

By S. P. Kinney, C. E. Wood, T. L. Joseph

In connection with its investigations of the blast-furnace process, the Bureau of Mines, in cooperation with the Minnesota School of Mines Experiment Station, developed a 6-ton experimental furnace. Such a furnace was needed to determine the feasibility of producing ferroman-ganese from Minnesota manganiferous iron ores, a problem of national importance because of the present need for manganese in the steel industry and our small reserves of ferro-grade ores. Furnace operators are reluctant to use new or untried raw materials or to make decided innovations in practice on account of the financial hazard of experimenting with full-scale equipment. A small furnace which can be operated at a relatively low cost is particularly adapted for testing new raw materials and for determining the feasibility of decided innovations in practice. Laboratory experiments, plus whatever information may be available, are valuable but often do not indicate the net result of changes in an operation involving a large number of interrelated variables. From time to time the cooperation of the Bureau of Mines is solicited in connection with problems involving departures from normal procedure. Under these circumstances some sort of a practical demonstration is a desirable forerunner to full-scale operations which appear feasible after small-scale tests. The Aluminum Co. of America was interested in knowing the practicability of smelting a charge of bauxite, iron ore, and limestone, of proportions that would produce slag of the following composition: A1203, 47 to 48 per cent.; CaO, 41 to 42 per cent.; SiO2,4 to 5 per cent.; TiO2, 2 to 3 per cent.; FeO, 1 percent., and MgO, 1.8 percent. In addition to determining whether it was feasible to operate a blast furnace on slag approaching the composition given above, a quantity of slag was needed for a series of experiments that would show the relative ease and cost of extracting alumina from slag which could be made in the blast furnace, as compared to extracting it from raw bauxite. The value of the slag as a raw material

THE man who forgot to mail the letters his wife gave him was for once justified at Tulsa, for envelopes, scratch paper and tablecloths were all in demand and through the two days of the meeting of the Petroleum Division, pencils were busy everywhere sketching out diagrams, drawing curves, figuring, or just taking notes. Those attending took the serious papers seriously, and discussion was wide-ranging but pointed. Despite the highly technical character of the papers presented, the chairmen had never to call for discussion; it was only necessary to say the paper was open for it. Both days the meetings lasted until after five in the afternoon, and it was enthusiastically voted to advance the meeting hour on Friday, in order to give more time. In all, ten papers, abstracts of which appeared in MINING AND METALLURGY for October, and copies of all but two of which were available in print, were presented in the two days, and no more could have been handled to advantage in that time. All but one of these dealt with problems of production engineering. That, the opening paper, was a general review of demand, supply and price in 1928, by Campbell Osborn, in which he argued for the price control of production and showed how the economic conditions determined development. J. Elmer Thomas presented a carefully prepared review of the same data, but came to somewhat different conclusions as to trend, and J. E. Pogue pointed out that in recent years it has been the manufacturing rather than the producing industries that have been notably profitable. These and other discussions were too long to be reported here, but will be printed in full later.

Jan 1, 1928

By Benjamin F. Tillson

The hammer drill rightly receives the credit for having made the one-man drill possible, and so many economies seem possible through the proper application of different types of hammer drills to various mining, quarrying, and excavating operations, that an indication of the 'economies effected by the New Jersey Zinc Co. at its Franklin mines may be of pertinent interest. When this company commenced its trials of hammer drills in 1907, these tools had not been developed to one-fourth the capacity and refinement which they have at present. At that time it was frequently stated that such a small tool, drilling holes of less diameter than the reciprocating rock drill, could not drill enough holes in a shift to permit the placing of sufficient explosive to break a tonnage of ore comparable with that produced by the "rock drills;" that the placing of small holes inclined upward, at angles steeper than 40' above the horizontal, could not be expected to produce results equal to the large flat, wet or dry, holes in the breasted back of an overhand stope, and would only shatter the ground so as to make the back unsafe. In spite of these adverse opinions, the hammer drills first showed their superiority over both heavy and light reciprocating drills in raising and in stoping, and then in drifting and quarry work. As a result, all of the reciprocating drills at the Franklin mines were scrapped three years ago, all of the mining work being accomplished with increased efficiency, as shown in detail in this article. With the advent of the hammer drill in this property, it was considered advisable to make comparative tests of all the tools accessible, and it has since been the policy to investigate the merits of any advance of the drilling art in order to get the maximum amount of work from the tools. The necessity of devising some means of standardizing drill tests, and of measuring the consumption of compressed air as well as the drilling speed, was early realized. The common test was to fill a measured air receiver with compressed air at a certain gauge pressure, run the drill until the pressure had dropped to too low a figure, then compute from the time, drop in pressure, and

Jan 1, 1915

By Eugene Coste

Although some of the observers who first paid especial attention to the occurrences of oil and gas in the strata (such as Hunt in 1859, Andrews in 1861; Winchell in 1865, Mendelejeff in 1876, Höfer in 1876, Minshall in 1881, and I. C. White in 1883) seem to have been impressed with the fact that oil and gas deposits were connected with the disturbances in the rocks caused by their upheavalll yet, with the exception of Mendelejeff, and possibly Andrews, these observers do not appear to have understood what is really the one essential factor in the occurrence of oil and gas in the strata: viz., the faulting, uplifting, fracturing, fis-suring, and jointing always accompanying even slight rock disturbances, and in certain districts (petroliferous provinces)2 allowing solfataric hydrocarbon emanations to force their way up from the interior and to reach and impregnate the porous portions of sediments subjected to the disturbances. Instead of this simple explanation to account -for the observed connection between petroleum deposits and rock disturbances, most of the observers mentioned above, and many others who have foliowed them on the same lines since, have entirely reversed the problem. To them, instead of the dissemination of gases from fissures into the sediments, it presented the accumulation and concentration, according to anticlinal or other geologic structures, of oil and gas originally present throughout the whole mass of the strata where they were produced by the decomposition or distillation of organic remains. Whether this important problem involves accumulation from sources within the strata themselves, or infiltration and dissemination from outside sources, may be easily determined if all preconceived ideas are put aside and the established facts only are considered. Physical Facts Sedimentary strata are composed of alternate beds of shales, sandstones, and limestones, most of which are sufficiently close-grained to

Jan 1, 1915

By Mark R. Lamb

THE treatment of slime is of special interest to those engaged in cyaniding gold- and silver-ores. The usual practice is to make as small a percentage of slime as possible. In many instances the slime is given no treatment, but is impounded in dams in the hope that the future will develop some method of economically treating this product. The filter-press was the first step upward from ordinary decantation, but, on account of heavy labor-charge and high cost, its use has been limited to high-grade material. The slime at the Combination mill at Goldfield averages perhaps $20 per ton, and although the values are quickly dissolved the filter-press installation was not entirely satisfactory, resulting in the erection of the canvas-cell filter, developed by Chas. Butters and his staff. This filter is a great improvement over the filter-press, and the following description of it will be of interest to those engaged in treating slime produced in crushing ores, especially in view of the fact that, by the use of this filter, slime can be treated at a lesser cost and with a higher percentage of gold- or silver-extraction than in the ordinary treatment of sand; and, moreover, the initial outlay for an all-sliming plant is less than that for the ordinary sand- and slime-plant. The economy of construction of the Butters filter-plant is clearly shown in Figs. 1 and 2, which illustrate the 20-frame filter of 40 tons capacity, now being installed by the Nevada Goldfield Reduction Co. In this construction the slime-pump is so connected that it can pump to or from either tank or the filter by changing the valve-settings-a combination which is necessary in this particular installation, since sufficient fall is not available for filling and discharging the filter by gravity. Ordinarily, a slime-plant comprises: a filter-box with frames

Jan 1, 1907

By Clark A. Sumner, D. Arthur Burnham

A process for recovery of greater than 99% of the copper contained in acid leach solutions by sulfide precipitation using hydrogen sulfide as a hydrometallurgical reagent has been developed. The process incorporates the concept of hydrogen sulfide addition to recycled copper sulfide solids in a turbulent flow area where further precipitation or agglomeration occurs to increase the effective particle size of the copper sulfide precipitate. Because the recycled solids provide a larger number of particles upon which momentary excesses of hydrogen sulfide are absorbed, oversulfidization of the product is prevented. Copper sulfide precipitates produced in this manner in a laboratory test reactor showed greatly improved physical characteristics compared to copper sulfide precipitates obtained by conventional direct precipitation in which H2S is bubbled directly into acid leach liquor. Copper sulfide precipitates were evaluated and compared by use of filtration tests and settling rate studies. Electron microscopic examination of the solids confirmed the presence of larger particles in reactor-precipitated copper sulfide. Flotation was examined as an alternative to filtration for recovery of CuS precipitates and was found to achieve complete CuS removal without addition of collector or frothing reagents in a period of 2 min. In the same test reactor, a rapidly floatable CuS precipitate was also formed by mixing H2S with acid liquors used to leach crushed copper oxide-copper sulfide ore (LPF process). In the presence of gangue from the crushed ore, flotation of both natural and reactor-produced copper sulfides resulted in recovery of better than 90% of the copper contained in the crushed ore.

Jan 1, 1974

By Guy Bjorge

IN recent years the Homestake mine has been served by three shafts, the B. &. M., the B. & M. No; 2 and the Ellison, supplemented by an inside shaft, the Milliken, extending from the 2000-ft. level to the 3200-ft. level. In 1932, when a new operating shaft was under consideration, the bottom of the mine was at the 3200-ft. level. The B: & M. and the B. & M. No. 2 shafts were down to the 1550-ft. level and the Ellison was being deepened from the 2600 to the 3200-ft. level. All ore was hoisted at the B. & M. and-Ellison shafts. Levels below the 2600 level, which were under development only, were served by the Milliken shaft. Below the 1550-ft. level, the mine was served only by the Ellison shaft from the surface. Within a few years, when ore reserves above the 1550-ft. level would be depleted, operation would be limited to the Ellison shaft and the auxiliary underground shaft. The Ellison shaft alone was not adequate for hoisting the entire output from the deeper levels and also handling all men and supplies. Further-more, assurance of safety and uninterrupted operation required- two fully equipped shafts to the deeper levels. Therefore a new operating shaft was authorized in November, 1932, and was named for A. J. M. Ross, the mine superintendent.

Jan 1, 1935

By Edward H. Robie

OF the current Adirondack iron mine development, the Benson Mines operation of the Tones and Laughlin Ore Co. (Jones & Laughlin Steel Corp. wholly owned subsidiary) is the last to go into operation. Following an active construction program in 1943, the mine. concentrator and sintering plant were scheduled to enter production in the fall. This description therefore cannot include any operating data, and details of equipment and flowsheet have not as yet been released.

Jan 1, 1943

By R. M. Foley, Hidesaburo Kurushima

About 25 pct of all Japanese pyrite comes from the Yanahara mine on Honchu Island. For the past 40 years lack of an economical recovery process forced the operator, Dowa Mining Co., to sell the pyrite for its contained sulfur only, leaving 7 million tons of high grade iron ore waste. Introduction of the Dorrco FluoSolids roasting system enabled the company to make use of its iron sulfides and also to find a market for the mine's considerable pyrrhotite production. The success of this project is of great importance to Japan's economy since it points the way toward material increase in her natural resources. Prior to use of the present process, no practical method was available for commercial exploitation of known large tonnages of pyrrhotite, while the copper content of the even larger deposits of pyrite made the roasted residue unacceptable for the iron and steel industry. In Europe, large amounts of copper-bearing pyrite cinder are given a chloridizing roast for separation of the copper and iron but this treatment is not economical in Japan where salt is imported from as far away as Egypt.

Jan 10, 1958

By E. Horton Jones

CONTENTS I Page Introduction ....:......................... 3 Chapter I. Unit Costs. . ...................... 4 Chapter II. Comparative Costs ..................... 20 Chapter III. Composite Costs..................... 32 Chapter IV. Wage Scale....................... 36 Chapter V. Raw Material Prices................. 37 Chapter VI. Description oF Costs ................... 64 Introduction We have endeavored in the following "sheets" to give the unit construction costs derived from 'the building of the Arizona Copper Co.'s new smelter, Clifton, Ariz., starting in February, 1912, and completing February, 1914.l In Chapter I—Unit Costs—are to be found the most elementary total unit costs which the accounts provide for. They are usable in the Clifton district. Here too are found the percentages to be added to an estimate for Engineering and General Expense. In Chapter II—Comparative Costs—these elementary costs have been classified, averaged and reported as labor and material unit costs. In such form the labor unit costs, when properly applied to similar conditions as these under which they were derived, are usable anywhere. The material unit costs are better disregarded for more accurate estimates and replaced by a newly priced bill of material. In Chapter III Composite Costs are given. They are unit costs built up from several elementary units, and likewise units of larger dimensions and simpler application, valuable for

Jan 1, 1915

By B. M. Larsen, T. E. Brower

A perspective is presented of the steel plant sulphur distribution and elimination problem from coal to liquid steel ready for teeming, giving distributions of sulphur over a range of coke sulphur content, and some methods of sulphur control, in the blast furnace, external desulphuriza-tion between blast furnace and open hearth, distribution between fuel, slag, and metal, and methods and limitations of control of sulphur in the open hearth furnace. AS a part of the 1951 AIME symposium on sulphur in steelmaking, it was thought that a discussion of the distribution of sulphur throughout the whole series of operations, from coal and ore to finished steel ingots, might have some value in giving a perspective on the whole problem. The following discussion is an attempt to present such an overall picture. The order is that of the actual plant operations, beginning with a very brief consideration of the coking process. Sulphur in Coal and Coke Since by far the largest source of sulphur entering the steelmaking cycle is in the coal used to make coke for the blast furnace, it would seem reasonable to eliminate some of it, either from the coal, or the coke, or during the coking process. This has appeared impracticable up to the present, at least, for two main reasons: the low activity of the organic sulphur in either coal or coke, and because of price limitations involved in treating a low cost material such as coke. A variable portion, usually M or less, of the sulphur is present in coal in the form of pyrites or similar compounds, and a large part of this sulphur may be removed in the coal washery. Most of the sulphur, however, is normally present as "organic" sulphur, intimately associated with the coal structure. Its distribution prevents any separation by mechanical means. Its low activity makes improbable ' any rapid chemical removal, although hydrogen will remove sulphur from both coal and coke. Thus, prolonged recirculation of coke oven gas in the coking process would tend to leave a smaller percentage of the total sulphur in the coke residue. Table I shows a typical distribution of sulphur from coal into products in the coking process. As the sulphur in the coal increases, the sulphur in the coke tends to increase in about the same proportion. Sulphur in the Blast Furnace The best picture of the situation in the blast furnace is provided by a sulphur balance of raw materials entering, and of products leaving, the furnace. The difficulties in accurate weighing and sampling of the variable solid materials entering this process, and the number of hours required for the raw materials to descend through the furnace under variable operating conditions, make it difficult to obtain an accurate balance. However, balances made over periods of weeks or months tend to average out some of these uncertainties. Table I1 presents three typical sulphur balances similar to a number that the writers have calculated. In most of these the slag volume calculated from the sulphur balance is, in some instances more, and in other instances less, than the value corresponding to the best input and output balances of the other slag constituents (lime, silica, alumina, etc.). Probably the greatest source of error in these calculations is the sulphur content of the slag. Despite some possible inaccuracies the balances of Table II show rather definitely the following points: 1—That 87 to 95 pct of the total sulphur input is in the coke and 95 to 97 pct of the total sulphur output is in the slag. Also, that if any sulphur leaves the furnace with the gas it is relatively small, amounting to a possible 1 pct or less. 2—At the lower sulphur coke level of 0.86 pct the total amount of sulphur charged is 15 Ib of sulphur per ton iron increasing to 26 lb per ton at the higher sulphur, intimately associated with the coal struc-rare burdens containing sulphur-rich ores will the total sulphur burden fail to be nearly proportional to the content in the coke used. 3—The 7 to 9 pct of the total sulphur input from the limestone of furnaces B and C is due to the relatively high sulphur content of the stone, 0.226 and 0.265 pct, respectively. In the case of furnace A, the sulphur content of the limestone was only 0.06 pct which resulted in only 3 pct of the total sulphur input coming from this source. It is rather interesting to compare the sulphur balances of a typical ferromanganese furnace with

Jan 1, 1952

By C. K. Gupta, P. K. Jena

Niobium (columbium) metal in the form of a button has been produced by calciothermic reduction of niobium pentoxide using sulfur as the heat booster. In these experiments with 50 g of niobium pentoxide per batch, the influence of percentage of calcium in excess of the stoichiometric, the percentage of sulfur by weight of the niobium oxide, and the outer-wall temperature of the bomb on the quality and yield of the metal has been studied. The maximum yield on this scale was 78 pct using 50 pct excess Ca and 20 pct of S and at a bomb-wall temperature of 600°C. In experiments conducted on 500 g of niobium pentoxide, reduction with 40 pct excess Ca and 20 pct of S, and at a bomb-wall temperature of 500°C, the.yield of the metal improved to 82 to 84 pct. Some of the reduced-metal samples have been electron-beam melted and the button melts thus obtained have been observed to be extremely ductile and capable of cold reduction to 98 pct without intermediate annealing. NIOBIUM, because of its high melting point (2468oC), its ductility, its resistance to corrosion especially in liquid metals, its high-temperature mechanical properties, and its relatively low capture cross section (1.1 barns) for thermal neutrons, has potentialities as a structural material in the field of nuclear engineering. Niobium and its alloys are also gaining importance in high-temperature technology as components in aircrafts, jet engines, and missiles, electronics, chemical engineering, and surgery. In 1904 Weiss and Aichel 1 produced niobium by reduction of its pentoxide by misch-metal. Since then a large number of investigations have been carried out for the extraction of niobium from its compounds. The various routes through which the metal niobium has been extracted from its compounds can broadely be classified into the following groups: a) reduction of its halides, oxides, and fluo-salts with metals like calcium, magnesium, sodium, and aluminum;2-10 b) reduction of its halides with hydrogen and oxides with carbon or carbides;11-18 c) electrolytic winning from its halides and fluo salts;19-25 and d) thermal decomposition and disproportion ion of its halides26-30 Among the processes in commercial use at present are sodium reduction or fused-salt electrolysis of potassium niobium fluoride, carbide or carbon reduction of the oxide, and hydrogen or metallothermic reduction of the chlorides. In 1907 Von Bolton2 prepared niobium by reducing niobium pentoxide with aluminum. Dennis and Adam-sona attempted reducing the oxide with magnesium powder in argon atmosphere and the resulting metal contained as much as 5 pct O. Mondolfo8 claimed a method for the reduction of the oxides with aluminum. In the case of both magnesium and aluminum reduction, it has been stated31 that by-product oxides such as MgO or A12O3 would involve a major separation problem. Further, in the case of alumino-thermic reduction, the solubility of aluminum in niobium and intermetallic formation have to be reckoned with. In 1922 Bridge3 produced niobium by calcium reduction of niobium pentoxide. Dennis and pdamson' obtained the metal by a similar method with an oxygen content of 0.2 pct. In most of the cases of metallothermic reduction of niobium oxides mentioned above, the metal niobium is obtained in the form of powder. In an attempt to produce massive niobium metal, lock' used iodine as the thermal booster in the bomb reduction of niobium pentoxide by calcium. Massive niobium metal was obtained with a maximum yield of 75 pct containing 0.1 pct 0. Joly32 carried out experiments on calcium reduction of niobium pentoxide on a 2-kg scale using sulfur as the heat booster in a sealed bomb filled with argon. In his experiments, the reaction was initiated by passing a current through niobium spiral wire embedded in the charge. In a typical run consisting of 2000 g of niobium pentoxide, 3100 g of calcium, and 800 g of sulfur (S/Nb2O5 = 3.3), he obtained massive metal in the form of a very uneven mass with a yield of -57 pct. With lower amounts of sulfur and calcium, powder niobium mixed with small metal globules was obtained and the yield was also poor. From these experiments he concluded that this method is not a suitable one for industrial development considering the quality and yield of metal obtainable and the possible hazards with higher ratios of sulfur to niobium pentoxide in the -~charere. In the present work, a detailed investigation on the calciothermic reduction of niobium pentoxide in a stainless-steel bomb in presence of sulfur as the heat booster was undertaken on a laboratory scale.

Jan 1, 1964

By B. Trentini

In the spectacular development of pure oxygen steel-making, the process using the vertical lance converter LD, is at the present time the most widely employed. Proper control of slag composition during the steel-making process appears to be essential in achieving satisfactory blowing from both the metallic yield and metallurgical points of view. The paper illustrates the primary importance of the presence of a large quantity of metal droplets in the slag during the process. In the case of both phosphorus and hematite pig iron, it can be deduced from the phase diagrams and confirmed by experimentation that nonhomogeneous slags are one of the causes of slag overflowing during the blow. The problem is however a complex one and further physicochemical studies appear necessary. Finally, the new continuous steelmakingprocess developed by IRSID is described. PEOPLE who knew Henri Marion Howe have said that he took great pleasure in speculating on the future of metallurgical processes. It is therefore not inappropriate to devote, in his memory, some description and discussion to processes unknown to the world of his time, in particular oxygen steelmaking and continuous steelmaking. The first industrial application to steelmaking of tonnage oxygen produced by air liquefaction was made in Germany just before the war and consisted in enriching the air blown through the bottom of a basic Begsemer converter in order to melt a higher proportion of scrap and to produce steels with lower nitrogen content than is achieved with conventional practice. While this process was being developed after the war, mostly in Western Europe, steelmakers were becoming increasingly familiar with the technique of blowing pure oxygen from the top, first by means of consumable steel pipes, with or without refractory shielding, and later by water-cooled lances, designed for the purpose and affording longer life. The field was then open for the wide use of pure oxygen in steelmaking, either in existing processes such as open-hearth or electric furnace, or in new processes. These new processes can be broadly classified according to the category of furnace employed. In the case of the vertical converter taken as the first category, bottom-blowing of pure oxygen causes extremely rapid wear of the refractory tuyeres, and although various expedients have been tried to overcome this drawback (such as mixing oxygen with CO2 or H2O or using high pressure oxygen), they have had to be abandoned. The solution for vertical converters has been found in top-blowing with a vertical water-cooled lance; this is known as the LD process or basic oxygen converter process.

Jan 1, 1969

By James Johnston

Synopsis.—A description of the working of the mills of this company and the metallurgical practice in vogue, by which a remarkably complex silver ore, averaging 54 oz. of silver per ton (run-of-mine ore), is treated to give a 95.66 per cent. extraction. The main features of the processes are: The cyanide amalgamation of the high-grade ore. The cyanide treatment of the low-grade ore, after extremely fine grinding and close classification, in a caustic soda solution. The use of a wet desulphurizing process to break up refractory silver minerals. The substitution of aluminum dust for zinc dust as a precipitant. The recovery and shipment of over 13,000,000 oz. of silver in bullion at 997 to 999 fine since this metallurgy was inaugurated, about 2.5 years ago. On the completion and successful operation of the mill to treat their high-grade ore,' the Nipissing Mining Co., under the general management of R. B. Watson, started a series of investigations of the possible treatment of the low-grade ore by the cyanide process, so that they would be in a position to market only silver bullion. These tests were run in July, 1911, on a large scale, by G. H. Clevenger, on an average mixture of Nipissing ore. The results obtained by a partiai amalgamation followed by cyanide treatment gave an extraction varying from 90 to 93 per cent. and were sufficiently encouraging to warrant Charles Butters, the company's Consulting Metallurgist, in recommending that the new low-grade ore mill under contemplation should be a cyanide mill, instead of a concentrator. The cost of such a mill, capable of treating 200 tons per day, to obtain a 90 per cent. extraction at a working cost of $3 per ton of ore treated, was estimated at $250,000. In coming to a decision as to which type of mill should be erected, the concentrator, with the subsequent shipping of concentrates to a smeltery,

Jan 1, 1915

By H. S. George

On one occasion when it seemed desirable to reveal under the microscope not only the metallic structure of an alloy, but certain small non-metallic inclusions that are ordinarily obliterated by etching, it was discovered that, by partly eclipsing the illuminating pencil of light rays, the residual light was thrown on the object from one side and the structure was brought out in relief. At the same time, the non-metallic inclusions were retained in clear view. In this first demonstration of lighting obliquely through the objective a card was thrust part way into the light beam between the arc iris and the light filter; the shadow of the card on the filter served to locate its position. Next several stiff-paper disks of various diameters were mounted on flexible wires; some plasticine on the other end of the wires made it easy to adjust and maintain a disk at any desired position in the light beam. To facilitate manipulation, an assortment of disks was mounted on a wheel, as shown in Fig. 1. The purpose of partly eclipsing the light beam was discussed in an earlier paper.' There it was pointed out that the usual methods of illuminating opaque objects for microscopic examination lend an unnatural appearance to the view, while the new method, which has been termed conical illumination, revels the true relationship of constituents by simulating natural lighting. In nature, all objects are lighted diffusely, or by light predominating from one direction, or by a combination of diffuse and directed light. Under these conditions, objects appear to have three dimensions—they possess relief. The kind of illumination known to metallographists as vertical or axial results in an unnatural appearance, as a large proportion of the illuminating rays are parallel to the line connecting the eye with the object, a condition almost never met in nature. Microconstituents

Jan 1, 1924